Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
MAX31785 is a PMBus compliant 6-Channel fan controller. It supports 6 fan
channels, 11 temperature sensors, and 6-Channel ADC to measure the remote
voltages. Datasheet can be found here:
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
This initial version of the driver has skeleton and support for the
fan channels. Requests for temperature sensors, and ADC Channels the
are serviced with the default values as per the datasheet. No additional
instrumentation is done. NV Log feature is not supported.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-5-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The Renesas RAA229004 is a PMBus Multiphase Voltage Regulator
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-9-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Currently there is no way for a board model's Kconfig stanza to
say "I have an i2c bus which the user can plug an i2c device into,
build all the free-standing i2c devices". The Kconfig mechanism
for this is the "device group". Add an I2C_DEVICES group along
the same lines as the existing PCI_DEVICES. Simple free-standing
i2c devices which a user might plausibly want to be able to
plug in on the QEMU commandline should have
default y if I2C_DEVICES
and board models which have an i2c bus that is user-accessible
should use
imply I2C_DEVICES
to cause those pluggable devices to be built.
In this commit we mark only a fairly conservative set of i2c devices
as belonging to the I2C_DEVICES group: the simple sensors and RTCs
(not including PMBus devices or devices which need GPIO lines to be
connected).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20220208155911.3408455-2-peter.maydell@linaro.org
This commit adds emulation of the magnetometer on the LSM303DLHC.
It allows the magnetometer's X, Y and Z outputs to be set via the
mag-x, mag-y and mag-z properties, as well as the 12-bit
temperature output via the temperature property. Sensor can be
enabled with 'CONFIG_LSM303DLHC_MAG=y'.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Message-id: 20220130095032.35392-1-kevin.townsend@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The MAX34451 is a Maxim power-supply system manager that can monitor up to 16 voltage rails or currents. It also contains a temperature sensor and supports up to four external temperature sensors.
This commit adds support for interfacing with it, and setting limits on the supported sensors.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-5-titusr@google.com>
[Moved the device to the sensor directory]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The ADM1272 is a PMBus compliant Hot Swap Controller and Digital Power
Monitor by Analog Devices.
This commit adds support for interfacing with it, and support for
setting and monitoring sensor limits.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1272.pdf
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-3-titusr@google.com>
[Moved the device to the sensor directory]
[remove include of trace.h, it is not needed]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Lots of this are expected to be coming in, create a directory for them.
Also move the tmp105.h file into the include directory where it
should be.
Cc: Cédric Le Goater <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
