The IGD OpRegion is enabled automatically when running in legacy mode,
but it can sometimes be useful in universal passthrough mode as well.
Without an OpRegion, output spigots don't work, and even though Intel
doesn't officially support physical outputs in UPT mode, it's a
useful feature. Note that if an OpRegion is enabled but a monitor is
not connected, some graphics features will be disabled in the guest
versus a headless system without an OpRegion, where they would work.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Enable quirks to support SandyBridge and newer IGD devices as primary
VM graphics. This requires new vfio-pci device specific regions added
in kernel v4.6 to expose the IGD OpRegion, the shadow ROM, and config
space access to the PCI host bridge and LPC/ISA bridge. VM firmware
support, SeaBIOS only so far, is also required for reserving memory
regions for IGD specific use. In order to enable this mode, IGD must
be assigned to the VM at PCI bus address 00:02.0, it must have a ROM,
it must be able to enable VGA, it must have or be able to create on
its own an LPC/ISA bridge of the proper type at PCI bus address
00:1f.0 (sorry, not compatible with Q35 yet), and it must have the
above noted vfio-pci kernel features and BIOS. The intention is that
to enable this mode, a user simply needs to assign 00:02.0 from the
host to 00:02.0 in the VM:
-device vfio-pci,host=0000:00:02.0,bus=pci.0,addr=02.0
and everything either happens automatically or it doesn't. In the
case that it doesn't, we leave error reports, but assume the device
will operate in universal passthrough mode (UPT), which doesn't
require any of this, but has a much more narrow window of supported
devices, supported use cases, and supported guest drivers.
When using IGD in this mode, the VM firmware is required to reserve
some VM RAM for the OpRegion (on the order or several 4k pages) and
stolen memory for the GTT (up to 8MB for the latest GPUs). An
additional option, x-igd-gms allows the user to specify some amount
of additional memory (value is number of 32MB chunks up to 512MB) that
is pre-allocated for graphics use. TBH, I don't know of anything that
requires this or makes use of this memory, which is why we don't
allocate any by default, but the specification suggests this is not
actually a valid combination, so the option exists as a workaround.
Please report if it's actually necessary in some environment.
See code comments for further discussion about the actual operation
of the quirks necessary to assign these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Match common vfio code with setup, exit, and finalize functions for
BAR, quirk, and VGA management. VGA is also changed to dynamic
allocation to match the other MemoryRegions.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The PCI spec recommends devices use additional alignment for MSI-X
data structures to allow software to map them to separate processor
pages. One advantage of doing this is that we can emulate those data
structures without a significant performance impact to the operation
of the device. Some devices fail to implement that suggestion and
assigned device performance suffers.
One such case of this is a Mellanox MT27500 series, ConnectX-3 VF,
where the MSI-X vector table and PBA are aligned on separate 4K
pages. If PBA emulation is enabled, performance suffers. It's not
clear how much value we get from PBA emulation, but the solution here
is to only lazily enable the emulated PBA when a masked MSI-X vector
fires. We then attempt to more aggresively disable the PBA memory
region any time a vector is unmasked. The expectation is then that
a typical VM will run entirely with PBA emulation disabled, and only
when used is that emulation re-enabled.
Reported-by: Shyam Kaushik <shyam.kaushik@gmail.com>
Tested-by: Shyam Kaushik <shyam.kaushik@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Specifying an emulated PCI vendor/device ID can be useful for testing
various quirk paths, even though the behavior and functionality of
the device with bogus IDs is fully unsupportable. We need to use a
uint32_t for the vendor/device IDs, even though the registers
themselves are only 16-bit in order to be able to determine whether
the value is valid and user set.
The same support is added for subsystem vendor/device ID, though these
have the possibility of being useful and supported for more than a
testing tool. An emulated platform might want to impose their own
subsystem IDs or at least hide the physical subsystem ID. Windows
guests will often reinstall drivers due to a change in subsystem IDs,
something that VM users may want to avoid. Of course careful
attention would be required to ensure that guest drivers do not rely
on the subsystem ID as a basis for device driver quirks.
All of these options are added using the standard experimental option
prefix and should not be considered stable.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Simplify access to commonly referenced PCI vendor and device ID by
caching it on the VFIOPCIDevice struct.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is just another quirk, for reset rather than affecting memory
regions. Move it to our new quirks file.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
VFIOQuirk hosts a single memory region and a fixed set of data fields
that try to handle all the quirk cases, but end up making those that
don't exactly match really confusing. This patch introduces a struct
intended to provide more flexibility and simpler code. VFIOQuirk is
stripped to its basics, an opaque data pointer for quirk specific
data and a pointer to an array of MemoryRegions with a counter. This
still allows us to have common teardown routines, but adds much
greater flexibility to support multiple memory regions and quirk
specific data structures that are easier to maintain. The existing
VFIOQuirk is transformed into VFIOLegacyQuirk, which further patches
will eliminate entirely.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Create a vendor:device ID helper that we'll also use as we rework the
rest of the quirks. Re-reading the config entries, even if we get
more blacklist entries, is trivial overhead and only incurred during
device setup. There's no need to typedef the blacklist structure,
it's a static private data type used once. The elements get bumped
up to uint32_t to avoid future maintenance issues if PCI_ANY_ID gets
used for a blacklist entry (avoiding an actual hardware match). Our
test loop is also crying out to be simplified as a for loop.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>