I left a TODO in the code because this still doesn't definitely
fix all issues.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5308 c046a42c-6fe2-441c-8c8c-71466251a162
This patch allows to use a "real" SCSI tape with qemu using
"-drive /dev/sgX,if=scsi".
It allows to decode correctly transfer length when the type of the
device is a tape.
Some issues remain when the application reading the tape tries to go
beyond the end of the stream (but they must be corrected at the SCSI
controller level).
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5305 c046a42c-6fe2-441c-8c8c-71466251a162
Raise UDC (Unexpected Disconnect) when a large enough number of
instructions has been executed by the SCRIPTS processor. This "solution"
is much simpler than temporarily interrupting execution.
This remedies the situation with Windows which downloads SCRIPTS code
that busy loops on guest main memory. Their drivers _do_ handle UDC
appropriately (at least XP and 2003).
It would be nicer to actually detect infinite loops, but until then,
this bandaid seems acceptable.
Since the situation seems to be rare enough, raise the number
of instructions to 10000 (previously 1000).
Three people other than myself had success with this patch.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5293 c046a42c-6fe2-441c-8c8c-71466251a162
According to SCSI documentation, for 6 bytes commands (READ(6),
WRITE(6)), if transfer length is 0 it specifies 256 blocks.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5292 c046a42c-6fe2-441c-8c8c-71466251a162
void *memset(void *s, int c, size_t n);
DESCRIPTION
The memset() function fills the first n bytes of the
memory area
pointed to by s with the constant byte c."
Reported by Dietmar Maurer.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5291 c046a42c-6fe2-441c-8c8c-71466251a162
Also avoid two signedness warnings in hw/omap2.c.
The API to attach new devices to serials is fine, bu the implementation
is a hack.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5263 c046a42c-6fe2-441c-8c8c-71466251a162
According to linux kernel sources, register a3 is set in case of failure
(and cleared in case of success) while register v0 contains the result
(or -errno in case of error).
The convention was not followed which results in weird behaviour.
Signed-off-by: Tristan Gingold <gingold@adacore.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5243 c046a42c-6fe2-441c-8c8c-71466251a162
* Remove the unused send_buf variable and its constant.
* Fix a math error
The variables recv_ptr and recv_used are not large enough to hold
the constant 384, which causes data corruption when the pointer is
reset with: s->recv_ptr = (s->recv_ptr + len) % RECV_BUF;
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5242 c046a42c-6fe2-441c-8c8c-71466251a162
The "Rx timeout" (aka. Character Timeout Indication) has no separate mask
bit in the IER register and according to the specs reading RHR is the only
way to reset the irq. However on the hardware (tested on OMAP2 UART which
is an extended 16550A) the RHR_IT bit in IER disables the irc, too. Linux
bluetooth serial dongle driver for N800 depends on this behavior.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5239 c046a42c-6fe2-441c-8c8c-71466251a162
Should prevent the ugly wrapping due to a typo in an earlier commit.
Fix by Gregor (gg@seh.de).
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5232 c046a42c-6fe2-441c-8c8c-71466251a162
handle different areas in different ways. This schema works with qemu
too, so it appears to be the common ground.
This patch proposes using this common ground for everyone, by spliting
raw qemu.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5228 c046a42c-6fe2-441c-8c8c-71466251a162
Add receive character feature to SH4 SCIF.
SH4-SCI feature implementation work is left.
(Shin-ichiro KAWASAKI)
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5221 c046a42c-6fe2-441c-8c8c-71466251a162
cpu_mips_irqctrl_init() function in hw/mips_timer.c is empty.
Attached patch removes it, and its callers.
(Hervé Poussineau)
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5214 c046a42c-6fe2-441c-8c8c-71466251a162
This patch adds support for removing USB devices by host address.
Which is usefull for things like libvirtd because there is no easy way to
find guest USB address of the host device.
In other words you can now do:
usb_add host:3.5
...
usb_del host:3.5
Before the patch 'usb_del' did not support 'host:' notation.
----
Syntax for specifying auto connect filters has been improved.
Old syntax was
host:bus.dev
host:pid:vid
New syntax is
host:auto:bus.dev[:pid:vid]
In both the cases any attribute can be set to "*".
New syntax is more flexible and lets you do things like
host:3.*:5533:* /* grab any device on bus 3 with vendor id 5533 */
It's now possible to remove auto filters. For example:
usb_del host:auto:3.*:5533:*
Active filters are printed after all host devices in 'info usb' output.
Which now looks like this:
Device 1.1, speed 480 Mb/s
Hub: USB device 1d6b:0002, EHCI Host Controller
Device 1.4, speed 480 Mb/s
Class 00: USB device 1058:0704, External HDD
Auto filters:
Device 3.* ID *:*
Signed-off-by: Max Krasnyansky <maxk@kernel.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5205 c046a42c-6fe2-441c-8c8c-71466251a162
Transaction lifetime was originally set to 10 frames. That was an arbitrary
number I picked without much thinking :).
I'm changing that to 32 frames because things like interrupt transfers
and such are scheduled at that rate. It seems like 1/32 is accepted as
lowest supported rate. OHCI, for example, defines exactly 32 interrupt
heads.
While testing USB webcam under XP I noticed that interrupt transactions were
being canceled and then resubmitted on a regular basis, which works but is a
waste of CPU cycles. This change fixes that.
All other devices I have are not affected.
Signed-off-by: Max Krasnyansky <maxk@kernel.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5199 c046a42c-6fe2-441c-8c8c-71466251a162
* Correct numeric value for the RST state.
* Add emulation for reseting a DMA channel.
* Add a few sanity checks.
* Make it compile with debug enabled.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5147 c046a42c-6fe2-441c-8c8c-71466251a162
Use NULL to trigger unassigned memory error on 32-bit accesses instead
of assert(0) as suggested by Blue Swirl.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5141 c046a42c-6fe2-441c-8c8c-71466251a162
This patch enhances the pcnet NIC emulation with better loopback mode
support, including CRC generation for looped-back packets in "raw" mode.
The patch has practically no impact on the normal RX and TX path.
Successfully tested against an ancient proprietary pcnet driver that
does a lot of hardware checks on boot-up and now works fine over qemu as
well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5135 c046a42c-6fe2-441c-8c8c-71466251a162
This adds trivial support for the R2D-PLUS FPGA, mostly just for the
versioning information that the kernel uses for IRL mappings, in addition
to handling the heartbeat and poweroff writes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5134 c046a42c-6fe2-441c-8c8c-71466251a162
Trivial patch adding CPU listing and the ability to do per-subtype
CVR/PVR/PRR values. Presently SH7750R and SH7751R definitions are
provided, as these are the ones in present use in-tree.
The CVR value for SH7751R is intentionally restricted so the kernel
boots, though this will want to be switched to the proper CVR value
once system emulation has sufficiently stabilized.
This also makes it trivial to abstract subtype specific registers like
MMU_PTEA and to set up feature bits in line with the kernel probing for
things like conditionalizing FPU/DSP context.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5133 c046a42c-6fe2-441c-8c8c-71466251a162
Trivial fix for a corner case: system_shutdown on isapc machines causes
qemu to segfaults due to accessing the uninitialized pm_state. Issue a
system shutdown instead.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5130 c046a42c-6fe2-441c-8c8c-71466251a162
Should be done according to spec.
Signed-off-by: Gleb Natapov <gleb@qumranet.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5128 c046a42c-6fe2-441c-8c8c-71466251a162
This patch fixes two spurious `may be used uninitialised' warnings
when compiling with some compilers.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5127 c046a42c-6fe2-441c-8c8c-71466251a162
While trying to make VX-3000 camera work on XP under KVM I realized that
we do not necessarily have to find original TD address. All we care about
is the token which identifies the transfer rather well (direction, endpoint,
size, etc).
This is especially important for the isochronous transfers because otherwise
they are being canceled left and right and we do not make much progress.
With this patch all devices that used bulk transfers that I've tried so
far continue to work just as well. And now my USB web cammera (isoc transfers)
is working well tool. It's not as smooth as native Windows but it's pretty
darn smooth.
The cool thing is that new USB code (both usb-uhci and usb-linux) is totaly
generic and does not need any special logic for ISOC.
Signed-off-by: Max Krasnyansky <maxk@kernel.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5072 c046a42c-6fe2-441c-8c8c-71466251a162
Fixes regression reported agains Linux 2.6.18.
Looks like XP and newer Linux kernels are less sensitive
to length returned for control transfers.
Signed-off-by: Max Krasnyansky <maxk@kernel.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5070 c046a42c-6fe2-441c-8c8c-71466251a162
Some bugs on SH4 MMU are fixed.
- When a TLB entry is overwritten or invalidated, tlb_flush_page() should be
invoked to invalidate old entry.
- When a ASID is changed, tlb_flush() should be invoke to invalidate entries
which have old ASID.
- The check for shared bit in TLB entry causes multiple TLB hit exception.
As SH3's MMU, shared bit is ignored.
- ASID is used when MMUCR's SV bit or SR's MD bit is zero.
No need to check both bits are zero.
(Shin-ichiro KAWASAKI)
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5068 c046a42c-6fe2-441c-8c8c-71466251a162
SH4 MMU's memory mapped TLB feature is implemented.
SH-Linux seems to write to memory mapped TLB to invalidate a TLB entry,
but does not to read it. So only memory write feature is implemented.
Work on memory read feature is left.
(Shin-ichiro KAWASAKI)
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5067 c046a42c-6fe2-441c-8c8c-71466251a162
The direction bit in the control register should not be directly
set using PPWCONTROL. The kernel gives the following debug message.
parport0 (ppdev0): use data_reverse for this!
More over setting the data pins to forward mode does not work,
perhaps a bug in the Linux PP driver. The right way to do this is
to use PPDATADIR to set the direction. The patch checks if the
user is toggling the direction bit, and invokes PPDATADIR to
do the job.
Signed-off-by: Vijay Kumar B <vijaykumar@bravegnu.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5063 c046a42c-6fe2-441c-8c8c-71466251a162
