after commit 003e15a180
the DPRINTF will broke compiling, adjust its location.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We identify devices by their Open Firmware device paths. The encoding
of the host controller and hub port numbers is incorrect:
usb_get_fw_dev_path() formats them in decimal, while SeaBIOS uses
hexadecimal. When some port number > 9, SeaBIOS will miss the
bootindex (lucky case), or apply it to another device (unlucky case).
The relevant spec[*] agrees with SeaBIOS (and OVMF, for that matter).
Change %d to %x.
Bug can bite only with host controllers or hubs sporting more than ten
ports. I'm not aware of any.
[*] Open Firmware Recommended Practice: Universal Serial Bus,
Version 1, Section 3.2.1 Device Node Address Representation
http://www.openfirmware.org/1275/bindings/usb/usb-1_0.ps
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Note: xhci can be configured with up to 15 ports (default is 4 ports).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Memory changes for QOMification and automatic tracking of MR lifetime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJT8et9AAoJEBvWZb6bTYbyIJAQAI3AlLSe27xWoUGfQUgWH30z
Rt/pShHz3BJMfQpD79JfTH8u6uBpkQmKtflerNT7FhXN9ULDzNq+b/jRtke8nkuy
ctCt05FhhK00rfWpUoRue4XiCuvbizBU7MK0DI3yCyNdXQyYnFvgnvsJtlqox8Zh
J5HZcBJEmdCiWBxq7UPk0qBitp4PqNoy7jlD/Ex3m7fJN5WK2cyspQIT9zmhehVn
B8Nwp+RitDDbXbwm0r18col5rFr/6Nj6+dW1gr+7sVJDLNsmJEqC2l3Kgk0wbPkG
Uqwbih29me9PC9/L1VLGHY0ApKDQ8JGE0GrYgEg162hbhoxEHkjjoHMhDUfV6Pj8
NkqcjjWl11UUhgkNqrGafayXbBVnOiEglxy8uXCeq14y9Xd/gjK9Fz6MQvRSOjms
PFmaKknhdmpxh0DuZmTix7WBmKim8zOiCE0/vrAPvwx5L+d1bn5xh6yQvtVjBMpU
Sru3Mhdm9bL9dUDBgOM/G6WCxSTVLBlExOblcYkQh03MfabD7bfplcrKYPXt5ull
Y8YLjqkoIfoy5t0ErvtlpdBJjeEz99JXU+wLQ6NYHnzwzTV+oUtSaEph14mAFOcY
XkFKdoPDI9PnyEfvy4193du8z/dSbhu7sWgHWbTCQyrcaNnSaVhlH43NUC+p23YN
8vfEsVLd1X7MFkDBUmWp
=M+/m
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
SCSI changes that enable sending vendor-specific commands via virtio-scsi.
Memory changes for QOMification and automatic tracking of MR lifetime.
# gpg: Signature made Mon 18 Aug 2014 13:03:09 BST using RSA key ID 9B4D86F2
# gpg: Good signature from "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: aka "Paolo Bonzini <bonzini@gnu.org>"
* remotes/bonzini/tags/for-upstream:
mtree: remove write-only field
memory: Use canonical path component as the name
memory: Use memory_region_name for name access
memory: constify memory_region_name
exec: Abstract away ref to memory region names
loader: Abstract away ref to memory region names
tpm_tis: remove instance_finalize callback
memory: remove memory_region_destroy
memory: convert memory_region_destroy to object_unparent
ioport: split deletion and destruction
nic: do not destroy memory regions in cleanup functions
vga: do not dynamically allocate chain4_alias
sysbus: remove unused function sysbus_del_io
qom: object: move unparenting to the child property's release callback
qom: object: delete properties before calling instance_finalize
virtio-scsi: implement parse_cdb
scsi-block, scsi-generic: implement parse_cdb
scsi-block: extract scsi_block_is_passthrough
scsi-bus: introduce parse_cdb in SCSIDeviceClass and SCSIBusInfo
scsi-bus: prepare scsi_req_new for introduction of parse_cdb
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The function is empty after the previous patch, so remove it.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
imitate nearby code about using '!value' or 'value == NULL'
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reason: we don't want commit to that interface yet. Possibly
the implementation will be switched over to use fsdev.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
"vmstate_xhci_event" was introduced in commit 37352df3 ("xhci: add live
migration support"), and first released in v1.6.0. The field list in this
VMSD is not terminated with the VMSTATE_END_OF_LIST() macro.
During normal use (ie. migration), the issue is practically invisible,
because the "vmstate_xhci_event" object (with the unterminated field list)
is only ever referenced -- via "vmstate_xhci_intr" -- if xhci_er_full()
returns true, for the "ev_buffer" test. Since that field_exists() check
(apparently) almost always returns false, we almost never traverse
"vmstate_xhci_event" during migration, which hides the bug.
However, Amit's vmstate checker forces recursion into this VMSD as well,
and the lack of VMSTATE_END_OF_LIST() breaks the field list terminator
check (field->name != NULL) in dump_vmstate_vmsd(). The result is
undefined behavior, which in my case translates to infinite recursion
(because the loop happens to overflow into "vmstate_xhci_intr", which then
links back to "vmstate_xhci_event").
Add the missing terminator.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Attach a name to the MTP interface (android phones have this too).
With this patch recent linux guests such as fedora 20 happily detect and
use the device. It shows up in nautilus file manager automatically, and
simple-mtpfs can mount it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Shut up Coverity's complaint about unchecked fcntl return values,
and especially make the code simpler and more efficient.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If libusb_get_device_list() fails, the uninitialized local variable
libusb_device would be passed to libusb_free_device_list(), that
will cause a crash, like:
(gdb) bt
#0 0x00007fbbb4bafc10 in pthread_mutex_lock () from /lib64/libpthread.so.0
#1 0x00007fbbb233e653 in libusb_unref_device (dev=0x6275682d627375)
at core.c:902
#2 0x00007fbbb233e739 in libusb_free_device_list (list=0x7fbbb6e8436e,
unref_devices=<optimized out>) at core.c:653
#3 0x00007fbbb6cd80a4 in usb_host_auto_check (unused=unused@entry=0x0)
at hw/usb/host-libusb.c:1446
#4 0x00007fbbb6cd8525 in usb_host_initfn (udev=0x7fbbbd3c5670)
at hw/usb/host-libusb.c:912
#5 0x00007fbbb6cc123b in usb_device_init (dev=0x7fbbbd3c5670)
at hw/usb/bus.c:106
...
So initialize libusb_device at the begin time.
Signed-off-by: Jincheng Miao <jmiao@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Due to an incomplete initialization, adding a usb-bt-dongle device through HMP
or QMP will cause a segmentation fault.
Signed-off-by: Hani Benhabiles <hani@linux.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
On FreeBSD polling a master pty while the other end is not connected
with G_IO_OUT only results in an endless wait. This is different from
the Linux behaviour, that returns immediately. In order to demonstrate
this, I have the following example code:
http://xenbits.xen.org/people/royger/test_poll.c
When executed on Linux:
$ ./test_poll
In callback
On FreeBSD instead, the callback never gets called:
$ ./test_poll
So, in order to workaround this, poll the source with G_IO_HUP (which
makes the code behave the same way on both Linux and FreeBSD).
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: xen-devel@lists.xenproject.org
[Add hw/char/cadence_uart.c too. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
"Init" and "uninit" suggest the functions don't allocate / free
storage. But they do.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We can pick the usb port speed in generic code, by looking at the port
and device speed masks and looking for the fastest match. So add a
function to do exactly that, and drop the speed setting code from
usb_desc_attach as it isn't needed any more.
This way we can set the device speed before calling port->ops->attach,
which fixes some xhci hotplug issues.
https://bugzilla.redhat.com/show_bug.cgi?id=1046873
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Extend compatibility test function to also figure whenever usb3
devices can be supported on ehci. Tweak ep0 maxpacketsize field
due to usb2 <-> usb3 difference.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb: xhci and mtp bugfixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=y+dq
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kraxel/tags/pull-usb-7' into staging
usb: usb3 streams support for usb-host and usb-redir
usb: xhci and mtp bugfixes.
# gpg: Signature made Mon 26 May 2014 09:44:09 BST using RSA key ID D3E87138
# gpg: Can't check signature: public key not found
* remotes/kraxel/tags/pull-usb-7:
usb-host-libusb: Set stream id when submitting bulk-stream transfers
usb-host-libusb: Add alloc / free streams ops
usb-host-libusb: Fill in endpoint max_streams when available
usb-redir: Add support for bulk streams
usb-mtp: handle usb_mtp_get_object failure
usb-mtp: handle lseek failure
usb-mtp: use bool to track MTPObject init status
xhci: add xhci_get_flag
xhci: add endpoint cap on express bus only
xhci: child detach fix
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add display property to the keyboard.
Add display and head properties to the tablet.
If properties are set bind device to the display specified to
setup input routing.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Stop setting nchildren to -1. Use separate bool variable to track
whenever we've already fetched the child objects instead.
Also make nchildren unsigned.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
xhci_child_detach() zaps the wrong slot when unplugging a device
connected via usb-hub: Instead of the device's slot the slot of the
usb-hub is used. Fix it.
https://bugzilla.redhat.com/show_bug.cgi?id=1075846
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Correct post load checks:
1. dev->setup_len == sizeof(dev->data_buf)
seems fine, no need to fail migration
2. When state is DATA, passing index > len
will cause memcpy with negative length,
resulting in heap overflow
First of the issues was reported by dgilbert.
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Currently all what's needed for single file libcacard/vcard_emul_nss.c
(libnss cflags) and hw/usb/ccid-card-emulated.c (libcacard includes)
together with the libs is added to global QEMU_CFLAGS and libs_softmmu.
Use the cflags only where really used (for two mentioned files), and
libs only where needed.
While at it, rename variables to better reflect reality: libcacard_*
is really nss_*.
This needs a bit more tweaking: $(NSS_LIBS) should not contain $glib_libs
(ditto for _cflags). But in order to fix it, some more preparations
should be made first. So add a FIXME comment.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VoYL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20140505' into staging
migration/next for 20140505
# gpg: Signature made Mon 05 May 2014 21:27:24 BST using RSA key ID 5872D723
# gpg: Can't check signature: public key not found
* remotes/juanquintela/tags/migration/20140505: (36 commits)
migration: expose xbzrle cache miss rate
migration: expose the bitmap_sync_count to the end
migration: Add counts of updating the dirty bitmap
XBZRLE: Fix one XBZRLE corruption issues
migration: remove duplicate code
Coverity: Fix failure path for qemu_accept in migration
Init the XBZRLE.lock in ram_mig_init
Provide init function for ram migration
Count used RAMBlock pages for migration_dirty_pages
Make qemu_peek_buffer loop until it gets it's data
Disallow outward migration while awaiting incoming migration
virtio: validate config_len on load
virtio-net: out-of-bounds buffer write on load
openpic: avoid buffer overrun on incoming migration
ssi-sd: fix buffer overrun on invalid state load
savevm: Ignore minimum_version_id_old if there is no load_state_old
usb: sanity check setup_index+setup_len in post_load
vmstate: s/VMSTATE_INT32_LE/VMSTATE_INT32_POSITIVE_LE/
virtio-scsi: fix buffer overrun on invalid state load
zaurus: fix buffer overrun on invalid state load
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CVE-2013-4541
s->setup_len and s->setup_index are fed into usb_packet_copy as
size/offset into s->data_buf, it's possible for invalid state to exploit
this to load arbitrary data.
setup_len and setup_index should be checked to make sure
they are not negative.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This adds migration support for OHCI.
This defines a descriptor for OHCIState.
This changes some OHCIState field types to be migration compatible.
This adds a descriptor for OHCIPort.
This migrates the EOF timer if the USB was started at the time of
migration.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Implementation of a USB Media Transfer Device device for easy
filesharing. Read-only. No access control inside qemu, it will
happily export any file it is able to open to the guest, i.e.
standard unix access rights for the qemu process apply.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add U suffix to avoid undefined behaviour. This is only
strictly necessary for the 1<<31 cases, but we add it for the
other constants in these groups for consistency.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If enabled, set the thread name at creation (on GNU systems with
pthread_set_np)
Fix up all the callers with a thread name
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
* QTest cleanups and test cases for PCI NICs
* NAND fix for "info qtree"
* Cleanup and extension of QOM machine tests
* IndustryPack test cases and conversion to QOM realize
* I2C cleanups
* Cleanups of legacy qdev properties
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=KRcc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/afaerber/tags/qom-devices-for-peter' into staging
QOM infrastructure fixes and device conversions
* QTest cleanups and test cases for PCI NICs
* NAND fix for "info qtree"
* Cleanup and extension of QOM machine tests
* IndustryPack test cases and conversion to QOM realize
* I2C cleanups
* Cleanups of legacy qdev properties
# gpg: Signature made Mon 17 Feb 2014 22:15:37 GMT using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
* remotes/afaerber/tags/qom-devices-for-peter: (49 commits)
qtest: Include system headers before user headers
qapi: Refine human printing of sizes
qdev: Use QAPI type names for properties
qdev: Add enum property types to QAPI schema
block: Handle "rechs" and "large" translation options
qdev: Remove hex8/32/64 property types
qdev: Remove most legacy printers
qdev: Use human mode in "info qtree"
qapi: Add human mode to StringOutputVisitor
qdev: Inline qdev_prop_parse()
qdev: Legacy properties are just strings
qdev: Legacy properties are now read-only
qdev: Remove legacy parsers for hex8/32/64
qdev: Sizes are now parsed by StringInputVisitor
qapi: Add size parser to StringInputVisitor
qtest: Don't segfault with invalid -qtest option
ipack: Move IndustryPack out of hw/char/
ipoctal232: QOM parent field cleanup
ipack: QOM parent field cleanup for IPackDevice
ipack: QOM parent field cleanup for IPackBus
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the scheduled transfer time be a bit behind, to
compensate for latencies. Without this xhci will wait
way to often for the mfindex wraparound, assuming the
scheduled time is in the future just because qemu is
a bit behind in processing the iso transfer requests.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
error_is_set(&var) is the same as var != NULL, but it takes
whole-program analysis to figure that out. Unnecessarily hard for
optimizers, static checkers, and human readers. Dumb it down to
obvious.
Gets rid of several dozen Coverity false positives.
Note that the obvious form is already used in many places.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Replace them with uint8/32/64.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Get rid of PCIDevice specific PCIDeviceClass.no_hotplug and use
generic DeviceClass.hotpluggable field instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Set SelectiveSuspendEnabled registy entry to one.
This makes Windows use remote suspend by default,
without manual registry fiddeling.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds support for special usb descriptors used by microsoft
windows. They allow more fine-grained control over driver binding and
adding entries to the registry for configuration.
As this is a guest-visible change the "msos-desc" compat property
has been added to turn this off for 1.7 + older
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Bugfixes for uas emulation.
Add remote wakeup support for ehci.
Add suspend support for xhci.
Misc minor tweaks and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=2yvC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'kraxel/tags/pull-usb-1' into staging
Improvements for usb3 bulk stream (usb core, xhci).
Bugfixes for uas emulation.
Add remote wakeup support for ehci.
Add suspend support for xhci.
Misc minor tweaks and fixes.
# gpg: Signature made Thu 28 Nov 2013 11:44:49 PM PST using RSA key ID D3E87138
# gpg: Can't check signature: public key not found
# By Hans de Goede (11) and others
# Via Gerd Hoffmann
* kraxel/tags/pull-usb-1:
usb: move usb_{hi,lo} helpers to header file.
usb: add vendor request defines
trace-events: Clean up after removal of old usb-host code
Revert "usb-tablet: Don't claim wakeup capability for USB-2 version"
ehci: implement port wakeup
xhci: Call usb_device_alloc/free_streams
usb: Add usb_device_alloc/free_streams
usb: Add max_streams attribute to endpoint info
uas: s/ui/iu/
uas: Fix response iu struct definition
uas: Bounds check tags when using streams
uas: Streams are numbered 1-y, rather then 0-x
uas: Fix / cleanup usb_uas_task error handling
uas: Only use report iu-s for task_mgmt status reporting
scsi: Add 2 new sense codes needed by uas
xhci: add support for suspend/resume
xhci: Add a few missing checks for disconnected devices
Message-id: 1385712381-30918-1-git-send-email-kraxel@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
This reduces the dependencies on trace.h.
Only one source file which needs hcd-ehci.h also needs trace.h.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Update portsc register and raise irq in case a suspended
port is woken up, so remote wakeup works on our ehci ports.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Note this code is not as KISS as I would like, the reason for this is that
the Linux kernel interface wants streams on eps belonging to one interface
to be allocated in one call. Things will also work if we do this one ep at a
time (as long as all eps support the same amount of streams), but lets stick
to the kernel API.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The various uas data structures are called IU-s, which is short for
Information Unit, rather then UI-s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch mirrors a patch to the Linux uas kernel driver which I've just
submitted. It looks like the qemu uas struct definitions were taken from
the Linux kernel driver, and have inherited the same mistake.
Besides fixing the response iu struct, the patch also drops the add_info
parameter from the usb_uas_queue_response() function, it is always 0 anyways,
and expressing 3 zero-bytes as a function argument is a bit hard.
Below is the long explanation for this change taken from the kernel commit:
The response iu struct before this patch has a size of 7 bytes, which is weird
since all other iu-s are explictly padded to a multiple of 4 bytes.
Submitting a 7 byte bulk transfer to the status endpoint of a real uasp device
when expecting a response iu results in an USB babble error, as the device
actually sends 8 bytes.
Up on closer reading of the UAS spec:
http://www.t10.org/cgi-bin/ac.pl?t=f&f=uas2r00.pdf
The reason for this becomes clear, the 2 entries in "Table 17 — RESPONSE IU"
are numbered 4 and 6, looking at other iu definitions in the spec, esp.
multi-byte fields, this indicates that the ADDITIONAL RESPONSE INFORMATION
field is not a 2 byte field as one might assume at a first look, but is
a multi-byte field containing 3 bytes.
This also aligns with the SCSI Architecture Model 4 spec, which UAS is based
on which states in paragraph "7.1 Task management function procedure calls"
that the "Additional Response Information" output argument for a Task
management function procedure call is 3 bytes.
Last but not least I've verified this by sending a logical unit reset task
management call with an invalid lun to an actual uasp device, and received
back a response-iu with byte 6 being 0, and byte 7 being 9, which is the
responce code for an invalid iu, which confirms that the response code is
being reported in byte 7 of the response iu rather then in byte 6.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Disallow the guest to cause us to address the data3 and status3 arrays
out of bounds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It is easier to simply make the arrays one larger, rather then
substracting one everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
-The correct error if we cannot find the dev is INCORRECT_LUN rather then
INVALID_INFO_UNIT
-Move the device not found check to the top so we only need to do it once
-Remove the dev->lun != lun checks, dev is returned by scsi_device_find
which searches by lun, so this will never trigger
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Regular scsi cmds should always report their status using a sense-iu, using
the sense code to report any errors.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The OS can ask the xhci controller to save and restore its
internal state, which is used by the OS when the system is
suspended and resumed.
This patch handles writes to the save + restore bits in the
command register. Only thing it does is updating the
restore error bit in the status register to signal an error
on restore. The guest OS should do a full reinitialization
after resume then.
This is the minimal patch which gets S3 going with xhci.
Implementing full save/restore support is TBD.
https://bugzilla.redhat.com/show_bug.cgi?id=1012365
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
One of the reworks of qemu's usb core made changes to usb-port's disconnect
handling. Now ports with a device will always have a non 0 dev member, but
if the device is not attached (which is possible with usb redirection),
dev->attached will be 0.
So supplement all checks for dev to also check dev->attached, and add an
extra check in a path where a device check was completely missing.
This fixes various crashes (asserts triggering) I've been seeing when xhci
attached usb devices get disconnected at the wrong time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The qdev_free() function name is misleading since all the function does
is unlink the device from its parent. The device is not necessarily
freed.
The device will be freed when its QObject refcount reaches zero. It is
usual for the parent (bus) to hold the final reference but there are
cases where something else holds a reference so "free" is a misleading
name.
Call object_unparent(obj) directly instead of having a qdev wrapper
function.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
* kraxel/usb.91:
usb-hcd-xhci: Update endpoint context dequeue pointer for streams too
usb-hcd-xhci: Report completion of active transfer with CC_STOPPED on ep stop
usb-hcd-xhci: Remove unused cancelled member from XHCITransfer
usb-hcd-xhci: Remove unused sstreamsm member from XHCIStreamContext
usb-host-libusb: Detach kernel drivers earlier
usb-host-libusb: Configuration 0 may be a valid configuration
usb-host-libusb: Fix reset handling
Message-id: 1382620267-18065-1-git-send-email-kraxel@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSXNO8AAoJECgfDbjSjVRp7VAH/0B73mCOiyVACGx7fazK3SGK
X8TxZWVtG5A77ISqKyrtjLAhK9DCQjEzQTbMNhXHM3Ar6crwo7nJZnQvH2Gh1X2p
34BOQSVc4rtXz5pwDIr48dBLrxeslwXub79chUs+IK1/4RSn3h3nuS3k6JVkmLJN
rcHMj4ljJmi4Hd9vOpmS1jo/a61usi36hhU7CMgcrsXzStZycBBzCozOB3VW8p1X
/iwyf91YjmNPkn9gA3/aViGjszu8jE91dkA0C+ljwvcGbs2yEl3LCWEJfsMvoh5P
2M+k0XXbHwq/P9PFMa/2/lWOo4EO4Oxa+G/6QvovJrteYnktr+E9DqjU8pCT7yI=
=CVfs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci, pc, acpi fixes, enhancements
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Oct 2013 07:33:48 AM CEST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony: (39 commits)
ssdt-proc: update generated file
ssdt: fix PBLK length
i386: ACPI table generation code from seabios
pc: use new api to add builtin tables
acpi: add interface to access user-installed tables
hpet: add API to find it
pvpanic: add API to access io port
ich9: APIs for pc guest info
piix: APIs for pc guest info
acpi/piix: add macros for acpi property names
i386: define pc guest info
loader: allow adding ROMs in done callbacks
i386: add bios linker/loader
loader: use file path size from fw_cfg.h
acpi: ssdt pcihp: updat generated file
acpi: pre-compiled ASL files
acpi: add rules to compile ASL source
i386: add ACPI table files from seabios
q35: expose mmcfg size as a property
q35: use macro for MCFG property name
...
Message-id: 1381818560-18367-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
With streams the endpoint context dequeue pointer should point to the
dequeue value for the currently active stream.
At least Linux guests expect it to point to value set by an set_ep_dequeue
upon completion of the set_ep_dequeue (before kicking the ep).
Otherwise the Linux kernel will complain (and things won't work):
xhci_hcd 0000:00:05.0: Mismatch between completed Set TR Deq Ptr command & xHCI internal state.
xhci_hcd 0000:00:05.0: ep deq seg = ffff8800366f0880, deq ptr = ffff8800366ec010
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
As we should per the XHCI spec "4.6.9 Stop Endpoint".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since qemu's USB model is geared towards emulated devices cancellation
is instanteneous, so no need to wait for cancellation to complete, as
such there is no wait for cancellation code, and the cancelled bool
as well as the bogus comment about it can be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If we detach the kernel drivers on the first set_config, then they will
be still attached when the device gets its initial reset. Causing the drivers
to re-initialize the device after the reset, dirtying the device state.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Quoting from: linux/Documentation/ABI/stable/sysfs-bus-usb:
Note that some devices, in violation of the USB spec, have a
configuration with a value equal to 0. Writing 0 to
bConfigurationValue for these devices will install that
configuration, rather then unconfigure the device.
So don't compare the configuration value against 0 to check for unconfigured
devices, instead check for a LIBUSB_ERROR_NOT_FOUND return from
libusb_get_active_config_descriptor().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The guest will issue an initial device reset when the device is attached, but
since the current usb-host-libusb code only actually does the reset when
udev->configuration != 0, and on attach the device is not yet configured,
the reset gets ignored. This means that the device gets passed to the guest
in an unknown state, which is not good.
The udev->configuration check is there because of the release / claim
interfaces done around the libusb_device_reset call, but these are not
necessary. If interfaces are claimed when libusb_device_reset gets called
libusb will release + reclaim them itself.
The usb_host_ep_update call also is not necessary. If the reset succeeds the
original config and interface alt settings will be restored.
Last if the reset fails, that means the device has either disconnected or
morphed into an another device and has been completely re-enumerated,
so it is treated by the host as a new device and our handle is invalid,
so on reset failure we need to call usb_host_nodev().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
pci_set_irq and the other pci irq wrappers use
PCI_INTERRUPT_PIN config register to compute device
INTx pin to assert/deassert.
An irq is allocated using pci_allocate_irq wrapper
only if is needed by non pci devices.
Removed irq related fields from state if not used anymore.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Device communication errors need to be reported to driver.
Add a debug message while at it.
Signed-off-by: Jan Vesely <jano.vesely@gmail.com>
Acked-by: Gerd Hoffmann <kraxel@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The USBPacket-s in the transfers need to be cleaned up so that the memory
allocated by the iovec in there gets freed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
And use it instead of prying the USBEndpoint out of the packet struct
in various places.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Transfers are part of an epctx, which is part of a slot, which is part of
a xhci. Transfers cannot dynamically be moved from one epctx to another,
so once created their xhci, slotid and epid are constant, so lets set these
up at creation time, rather then re-initializing them with the same
value each time a transfer gets submitted.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
According to the xhci spec the total number of streams is
2 ^ (MaxPStreams + 1), and this is also how the Linux xhci driver
uses this field.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The usb-host code has been rewritten for qemu 1.5 to use libusb,
the old code has been left in as temporary fallback. Now we are
two releases further out, targeting the 1.7 release. No major
issues with the new code poped up until now. Time to remove it
from tre tree. Should we ever need it again for some reason --
git has a copy for us in the history.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Use usb_legacy_register handling to create bt-dongle device and remove code
dependency from vl.c so CONFIG_USB_BLUETOOTH can be disabled.
Signed-off-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This reverts commit a309ee6e0a.
This isn't in line with the usb specification and adds regressions,
win7 fails to drive the usb hub for example.
Was added because it "solved" the issue of hubs interacting badly
with the xhci host controller. Now with the root cause being fixed
in xhci (commit <FIXME>) we can revert this one.
Cc: qemu-stable@nongnu.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb3 bulk endpoints with streams are implicitly pipelined now,
so the requests will actually be processed in parallel. Also
allow them to complete out-of-order.
Fixes stalls in the uas driver.
Cc: qemu-stable@nongnu.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Respect the interval for interrupt endpoints, so we don't finish
transfers as fast as possible but at the rate configured by the guest.
Fixes guest deadlocks triggered by interrupt storms.
Cc:
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
To be passed to object_initialize().
Since commit 39355c3826 the argument is
void*, so drop some superfluous (BusState *) casts or direct parent
field usages.
Signed-off-by: Andreas Färber <afaerber@suse.de>
To be passed to qbus_create_inplace().
Use DEVICE() cast to avoid a direct parent field access.
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
To be passed to qbus_create_inplace().
Use DEVICE() casts instead of direct parent field access.
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
include/qemu/timer.h has no need to include main-loop.h and
doing so causes an issue for the next patch. Unfortunately
various files assume including timers.h will pull in main-loop.h.
Untangle this mess.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Rename four functions in preparation for new API.
Rename qemu_timer_expired to timer_expired
Rename qemu_timer_expire_time_ns to timer_expire_time_ns
Rename qemu_timer_pending to timer_pending
Rename qemu_timer_expired_ns to timer_expired_ns
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reinitialize dev->cs to NULL after deleting it, to make sure it isn't
used afterwards.
Reported-by: Martin Cerveny <M.Cerveny@computer.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Guest trying to reset a endpoint of a disconnected device resulted in
xhci trying to dereference uport while being NULL, thereby crashing
qemu. Fix that by adding a check. Drop unused dev variable while
touching that code bit.
Cc: qemu-stable@nongnu.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Current hcd-ohci does not handle DMA errors. However they may happen
so here we introduce simple error handling.
On such errors, a typical OHCI will stop operating, signal the guest
about the error by sending "UnrecoverableError Event", set itself into
error state and set "Detected Parity Error" in its PCI config space
to signal that it got an error and so does the patch.
This also adds ohci_die() call to ohci_bus_start() to handle possible
failure of qemu_new_timer_ns().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When the guest goes suspend the uhci controller while there are
pending resume requests on the ports go signal global resume
instantly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The macro g_assert_not_reached is a better self documenting replacement
for assert(0) or assert(false).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Let scsi_bus_legacy_add_drive() and scsi_bus_legacy_handle_cmdline()
return an Error**. Prepare qdev initfns for QOM realize error model.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Introduce type constant and avoid DO_UPCAST().
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Avoid remaining OHCIPCIState::pci_dev uses, rename parent fields]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace direct uses of XHCIState::pci_dev with QOM casts and rename it
to parent_obj.
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Define and use standard QOM cast macro. Remove usages of DO_UPCAST()
and direct -> style upcasting.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[AF: Dropped usb_xhci_init() DeviceState argument and renamed variable]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The name field in a VMStateDescription is part of the migration state
versioning, so changing it will break migration. It's therefore a
bad idea to use a QOM typename macro to initialize it, because in
general we're free to rename QOM types as part of code refactoring
and cleanup. For the handful of devices that were doing this by
mistake, replace the QOM typenames with the corresponding literal
strings.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
[AF: Use TYPE_PVSCSI for TypeInfo instead]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This patch adds a serial property for all usb devices, which can be
used to set the serial number of a usb device (as listed by lsusb -v)
to a specific value. Applies to emulated devices only.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The next libusb release will deprecate libusb_get_port_path, and since
we compile with -Werror, this breaks the build.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add Faraday FUSBH200 support, which is slightly different from EHCI spec.
(Or maybe simply a bad/wrong implementation...)
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Replace PORTSC macros with variables which could then be
configured in ehci_xxxx_class_init(...)
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This prepares an EHCI device for the Nvidia Tegra2 SoC family.
Values based on patch by Vincent Palatin and verified against TRM v01p.
Cc: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This makes the mem MemoryRegion available to derived instance_inits.
Keep the bus in realize for now since naming breaks in instance_init.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The SysBus qdev initfn merely calls SysBusDeviceClass::init, so we can
replace it with a realizefn already. This avoids getting into any initfn
ambiguity with the upcoming Faraday EHCI implementation.
Rename internal usb_ehci_initfn() to usb_ehci_realize() to allow to
return Errors from common initialization code as well.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The DMAContext is a simple pointer to an AddressSpace that is now always
already available. Make everyone hold the address space directly,
and clean up the DMA API to use the AddressSpace directly.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With all preparing pieces in place we can finally drop in
the vmstate structs and the postload function.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Factor out endpoint context initialization to a separate function.
xhci live migration will need that too, in post_load.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Factor out endpoint context allocation to a separate function.
xhci live migration will need that too, in post_load.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
USB_RET_ASYNC is -6, so inflight was always false.
Signed-off-by: Ed Maste <emaste@freebsd.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
USB_DEV_FLAG_IS_HOST is the bit number, not value. Booting with a
"Fitbit Base Station" USB dongle was triggering this assert.
Signed-off-by: Michael Marineau <mike@marineau.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Due to various unfortunate reasons we cannot reliable detect a guest
cancelling a packet as soon as it happens, instead we detect cancels
with some delay.
When packets are handled async, and we directly pass the guest memory for
the packet to the usb-device as iovec, this means that the usb-device can
write to guest-memory which the guest has already re-used for other purposes
-> not good!
This patch fixes this by adding an intermediate buffer and writing back not
only the result, but also the data, of async completed packets when scanning
the schedule.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Alloes to pass through usb2 devices on usb1 host controllers if possible.
Brings the libusb implementation to feature-parity with the linux usbfs
code, so the usb-host implementation in 1.5 (libusb) doesn't regress
compared to 1.4 (usbfs).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This adds the possibility to create a scsi-bus with a specified name.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1367330931-12994-4-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We don't support T=1 so we shouldn't advertise it by default.
Two independent changes:
* Default ATR
sets T=0. This gets overwritten by the client provided ATR later.
* Class descriptor
changes dwAdvertise dwProtocols.PPPP to 0x1 and dwProtocols.RRRR=0 per spec.
Signed-off-by: Alon Levy <alevy@redhat.com>
Reviewed-by: Marc-André Lureau <mlureau@redhat.com>
Introduces a new utility function: parse_debug_env to avoid code
duplication.
This overrides whatever debug value is set on the corresponding devices
from the command line, and is meant to ease the usage with any
management stack. For libvirt you can set environment variables by
extending the dom namespace, i.e:
<domain type='kvm' id='3' xmlns:qemu='http://libvirt.org/schemas/domain/qemu/1.0'>
<qemu:commandline>
<qemu:env name='QEMU_CCID_PASSTHRU_DEBUG' value='4'/>
<qemu:env name='QEMU_CCID_DEBUG' value='4'/>
</qemu:commandline>
</domain>
Signed-off-by: Alon Levy <alevy@redhat.com>
Reviewed-by: Marc-André Lureau <mlureau@redhat.com>
By not advertising USB wakeup support (which we don't).
Signed-off-by: Alon Levy <alevy@redhat.com>
Reviewed-by: Marc-André Lureau <mlureau@redhat.com>
Program received signal SIGSEGV, Segmentation fault.
__strcmp_sse42 () at ../sysdeps/x86_64/multiarch/strcmp-sse42.S:164
164 movdqu (%rsi), %xmm2
(gdb) bt
at /home/elmarco/320g/src/qemu/hw/ccid-card-emulated.c:477
at /home/elmarco/320g/src/qemu/hw/ccid-card-emulated.c:503
Signed-off-by: Marc-André Lureau <mlureau@redhat.com>
Reviewed-by: Alon Levy <alevy@redhat.com>
Allows to remove one FIXME. Makes LIBUSB_LOG_LEVEL_WARNING build errors
go away. And starting with that version libusb has a LIBUSBX_API_VERSION
define which allows to easily #ifdef version dependencies should that
need arrive in the future.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Report the supported speeds for device and port in the error message.
Also add the speeds to the tracepoint. And while being at it drop
the redundant error message in usb_desc_attach, usb_device_attach will
report the error anyway.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
With pipelining it is possible to encounter a finished packet when cleaning
the queue due to a halt. This happens when a non stall error happens while
talking to a real device. In this case the queue on the usb-host side will
continue processing packets, and we can have completed packets waiting in
the queue after an error condition packet causing a halt.
There are 2 reasons to discard the completed packets at this point, rather
then trying to writing them back to the guest:
1) The guest expect to be able to cancel and/or change packets after the
packet with the error without doing an unlink, so writing them back may
confuse the guest.
2) Since the queue does not advance when halted, the writing back of these
packets will fail anyways since p->qtdaddr != q->qtdaddr, so the
ehci_verify_qtd call in ehci_writeback_async_complete_packet will fail.
Note that 2) means that then only functional change this patch introduces
is the printing of a warning when this scenario happens.
Note that discarding these packets means that the guest driver and the device
will get out of sync! This is unfortunate, but should not be a problem since
with a non stall error (iow an io-error) the 2 are out of sync already anyways.
Still this patch adds a warning to signal this happening.
Note that sofar this has only been seen with a DVB-T receiver, which gives
of a MPEG-2 stream, which allows for recovering from lost packets, see:
https://bugzilla.redhat.com/show_bug.cgi?id=890320
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reimplement usb-host on top of libusb.
Reasons to do this:
(1) Largely rewritten from scratch, nice opportunity to kill historical
cruft.
(2) Offload usbfs handling to libusb.
(3) Have a single portable code base instead of bsd + linux variants.
(4) Bring usb-host support to any platform supported by libusbx.
For now this goes side-by-side to the existing code. That is only to
simplify regression testing though, at the end of the day I want remove
the old code and support libusb exclusively. Merge early in 1.5 cycle,
remove the old code after 1.5 release or something like this.
Thanks to qdev the old and new code can coexist nicely on linux. Just
use "-device usb-host-linux" to use the old linux driver instead of the
libusb one (which takes over the "usb-host" name).
The bsd driver isn't qdev'ified so it isn't that easy for bsd.
I didn't bother making it runtime switchable, so you have to rebuild
qemu with --disable-libusb to get back the old code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Is good enougth for unique device addresses and avoids the need for any
state for device addressing. Makes live migration support easier. Also
makes device->slot lookups trivial.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Check for port reset first and skip everything else then.
Add sanity checks for PLS updates.
Add PLC notification when entering PLS_U0 state.
This gets host-initiated port resume going on win8.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb-serial has a qdev chardev property, and hw/qdev-properties-system.c
already contains:
static void release_chr(Object *obj, const char *name, void *opaque)
{
DeviceState *dev = DEVICE(obj);
Property *prop = opaque;
CharDriverState **ptr = qdev_get_prop_ptr(dev, prop);
CharDriverState *chr = *ptr;
if (chr) {
qemu_chr_add_handlers(chr, NULL, NULL, NULL, NULL);
qemu_chr_fe_release(chr);
}
}
So doing the qemu_chr_add_handlers(s->cs, NULL, NULL, NULL, NULL); from
the usb handle_destroy function too will lead to it being done twice.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Headers in include/exec/ are for the deepest innards of QEMU,
they should almost never be included directly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
# By Paolo Bonzini
# Via Paolo Bonzini
* bonzini/hw-dirs: (35 commits)
hw: move private headers to hw/ subdirectories.
MAINTAINERS: update for source code movement
hw: move last file to hw/arm/
hw: move hw/kvm/ to hw/i386/kvm
hw: move ARM CPU cores to hw/cpu/, configure with default-configs/
hw: move other devices to hw/misc/, configure with default-configs/
hw: move NVRAM interfaces to hw/nvram/, configure with default-configs/
hw: move GPIO interfaces to hw/gpio/, configure with default-configs/
hw: move interrupt controllers to hw/intc/, configure with default-configs/
hw: move DMA controllers to hw/dma/, configure with default-configs/
hw: move VFIO and ivshmem to hw/misc/
hw: move PCI bridges to hw/pci-* or hw/ARCH
hw: move SD/MMC devices to hw/sd/, configure with default-configs/
hw: move timer devices to hw/timer/, configure with default-configs/
hw: move ISA bridges and devices to hw/isa/, configure with default-configs/
hw: move char devices to hw/char/, configure via default-configs/
hw: move more files to hw/xen/
hw: move SCSI controllers to hw/scsi/, configure via default-configs/
hw: move SSI controllers to hw/ssi/, configure via default-configs/
hw: move I2C controllers to hw/i2c/, configure via default-configs/
...
Message-id: 1365442249-18259-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it necessary to compile these files per-target.
However, fixing this does not belong in these patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
# By Gerd Hoffmann (7) and Hans de Goede (3)
# Via Gerd Hoffmann
* kraxel/usb.79:
usb-tablet: Don't claim wakeup capability for USB-2 version
usb: update docs for bus name change
usb-hub: report status changes only once
usb-hub: limit chain length
xhci: zap unused name field
xhci: remove unimplemented printfs
xhci: remove leftover debug printf
xhci: fix numintrs sanity checks
usb-redir: Add flow control support
usb-redir: Fix crash on migration with no client connected
usb-storage takes care to fetch the USB serial number from -drive
options, but it neglected to pass its own 'serial' property to the
scsi-disk it creates. With this patch, the 'serial' qdev property and
the 'serial' option in -drive behave the same and correctly apply the
serial number on both USB and SCSI level.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Our ehci code does not implement wakeup support, so claiming support for
it with usb-tablet in USB-2 mode causes all tablet events to get lost.
http://bugzilla.redhat.com/show_bug.cgi?id=929068
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If no client is connected on the src side, then we won't receive a
parser during migrate, in this case usbredir_post_load() should be a nop,
rather then to try to derefefence the NULL dev->parser pointer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Most frontends can't really determine if the guest actually has the frontend
side open. So lets automatically generate fe_open / fe_close as soon as a
frontend becomes ready (as signalled by calling qemu_chr_add_handlers) /
becomes non ready (as signalled by setting all handlers to NULL).
And allow frontends which can actually determine if the guest is listening to
opt-out of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Message-id: 1364292483-16564-5-git-send-email-hdegoede@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rename the opened variable to be_open to reflect that it contains the
opened state of the backend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Message-id: 1364292483-16564-2-git-send-email-hdegoede@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix the awkward API of mangling the caller specified PCIe type and
just provide an interface to initialize an endpoint device. This
will pick either a regular endpoint or integrated endpoint based on
the bus and return pcie_cap_init to doing exactly what is asked.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qdev-monitor.c is the only "core qdev" file that is not used in
user-mode emulation, and it does not define anything that is used
by hardware models. Remove it from the hw/ directory and
remove hw/qdev-monitor.h from hw/qdev.h too; this requires
some files to have some new explicitly includes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes the following compilation error:
hw/usb/hcd-xhci.c:1156:17: error: format ‘%llx’ expects argument of type
‘long long unsigned int’, but argument 4 has type ‘unsigned int’
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit 8550a02d12 added a streams
parameter to usb_wakeup and didn't update redirect.c. Fix it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add streams support to the xhci emulation. No secondary streams yet,
only linear stream arays are supported for now.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds support for usb3 streams to the usb subsystem core.
This is just adding a streams field / parameter in a number of places.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fix the ordering of the endpoint descriptors for superspeed endpoints:
The superspeed companion must come first, possible additional
descriptors for the endpoint after that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb_packet_copy can handle combined packets now,
so it isn't needed to special-case them any more.
Also use the new usb_packet_size() function.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The code handling the "-usbdevice host:..." legacy command line
syntax is moved to the new hw/usb/host-legacy.c file.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Leave the core usb devices (usb hub, tablet, mouse, keyboard)
enabled unconditionally. Make the other ones configurable.
Exceptions:
- bluetooth: not qdevified yet, has a vl.c dependency because
of that, thus disabling isn't as easy as not linking the
object file.
- smardcard: ccid-card-emulated depends on that one *and*
CONFIG_SMARTCARD_NSS. So it isn't a one-liner and comes
as separate patch because of that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
To support multiqueue nic, this patch separate the nic destructor from
qemu_del_net_client() to a new helper qemu_del_nic() since the mapping bettween
NiCState and NetClientState were not 1:1 in multiqueue. The following patches
would refactor this function to support multiqueue nic.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
To support multiqueue, this patch introduces a helper qemu_get_nic() to get
NICState from a NetClientState. The following patches would refactor this helper
to support multiqueue.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
To support multiqueue, the patch introduce a helper qemu_get_queue()
which is used to get the NetClientState of a device. The following patches would
refactor this helper to support multiqueue.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Basically the same as usb-storage, but without automatic scsi
device setup. Also features support for up to 16 LUNs.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This reverts commit a1cbfd554e.
Test isn't useless. scsi_req_enqueue() may finish the request (will
actually happen for requests which don't trigger any I/O such as
INQUIRY), then call usb_msd_command_complete() which in turn will
set s->req to NULL after unref'ing it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
84f2d0ea added an argument to function usb_host_info.
The stub function must match the declaration in usb.h.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch change all info call back function to take
additional QDict * parameter, which allow those command
take parameter. Now it is set to NULL at default case.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
scsi_req_new() never returns null, and scsi_req_enqueue() dereferences
the pointer, so checking for null is useless.
Spotted by Coverity.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kraxel/usb.76:
usb-host: Initialize dev->port the obviously safe way
usb-host: Drop superfluous null test from usb_host_auto_scan()
ehci: Assert state machine is sane w.r.t. EHCIQueue
xhci: nuke transfe5rs on detach
xhci: call xhci_detach_slot on root port detach too
xhci: create xhci_detach_slot helper function
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Coverity worries the strcpy() could overrun the destination. It
can't, because the source always points to usb_host_scan()'s auto
port[], which has the same size. Use pstrcpy() anyway, to hush the
checker.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Coverity points out that port is later passed to usb_host_open(),
which dereferences it. It actually can't be null: it always points to
usb_host_scan()'s auto port[]. Drop the superfluous port == NULL
test.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Coverity worries the EHCIQueue pointer could be null when we pass it
to functions that reference it. The state machine ensures it can't be
null then. Assert that, to hush the checker.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since 39bffca203 (qdev: register all
types natively through QEMU Object Model), TypeInfo as used in
the common, non-iterative pattern is no longer amended with information
and should therefore be const.
Fix the documented QOM examples:
sed -i 's/static TypeInfo/static const TypeInfo/g' include/qom/object.h
Since frequently the wrong examples are being copied by contributors of
new devices, fix all types in the tree:
sed -i 's/^static TypeInfo/static const TypeInfo/g' */*.c
sed -i 's/^static TypeInfo/static const TypeInfo/g' */*/*.c
This also avoids to piggy-back these changes onto real functional
changes or other refactorings.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Buffered bulk mode is intended for bulk *input* endpoints, where the data is
of a streaming nature (not part of a command-response protocol). These
endpoints' input buffer may overflow if data is not read quickly enough.
So in buffered bulk mode the usb-host takes care of the submitting and
re-submitting of bulk transfers.
Buffered bulk mode is necessary for reliable operation with the bulk in
endpoints of usb to serial convertors. Unfortunatelty buffered bulk input
mode will only work with certain devices, therefor this patch also adds a
usb-id table to enable it for devices which need it, while leaving the
bulk ep handling for other devices unmodified.
Note that the bumping of the required usbredir from 0.5.3 to 0.6 does
not mean that we will now need a newer usbredir release then qemu-1.3,
.pc files reporting 0.5.3 have only ever existed in usbredir builds directly
from git, so qemu-1.3 needs the 0.6 release too.
Changes in v2:
-Split of quirk handling into quirks.c
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It uses a different capsbase and opregbase than the Xilinx device.
Signed-off-by: Liming Wang <walimisdev@gmail.com>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Cc: Igor Mitsyanko <i.mitsyanko@samsung.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This allows specific derived models to use different values.
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
SysBus EHCI was introduced in a hurry before 1.3 Soft Freeze.
To use QOM casts in place of DO_UPCAST() / FROM_SYSBUS(), we need an
identifying type. Introduce generic abstract base types for PCI and
SysBus EHCI to allow multiple types to access the shared fields.
While at it, move the state structs being amended with macros to the
header file so that they can be embedded.
The VMSTATE_PCI_DEVICE() macro does not play nice with the QOM
parent_obj naming convention, so defer that cleanup.
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
