Doorbells in SMT need to coordinate msgsnd/msgclr and DPDES access from
multiple threads that affect the same state.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The decrementer store function has logic that short-cuts the timer if a
very small value is stored (0, 1, or 2) and raises an interrupt
directly. There are two problem with this on BookE.
First is that BookE says a decrementer interrupt should not be raised
on a store of 0, only of a decrement from 1. Second is that raising
the irq directly will bypass the auto-reload logic in the booke decr
timer function, breaking autoreload when 1 or 2 is stored.
Fix this by removing that small-value special case. It makes this
tricky logic even more difficult to reason about, and it hardly matters
for performance.
Cc: sdicaro@DDCI.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230530131214.373524-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
It is possible to store a very large value to the decrementer that it
does not raise the decrementer exception so the timer is scheduled, but
the next time value wraps and is treated as in the past.
This can occur if (u64)-1 is stored on a zero-triggered exception, or
(u64)-1 is stored twice on an underflow-triggered exception, for
example.
If such a value is set in DECAR, it gets stored to the decrementer by
the timer function, which then immediately causes another timer, which
hangs QEMU.
Clamp the decrementer to the implemented width, and use that as the
value for the timer calculation, effectively preventing this overflow.
Reported-by: sdicaro@DDCI.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230530131214.373524-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This new method will check if any pending interrupt was unmasked and
then call cpu_interrupt/cpu_reset_interrupt accordingly. Code that
raises/lowers or masks/unmasks interrupts should call this method to
keep CPU_INTERRUPT_HARD coherent with env->pending_interrupts.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221021142156.4134411-2-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This enum defines the bit positions in env->pending_interrupts for each
interrupt. However, except for the comparison in kvmppc_set_interrupt,
the values are always used as (1 << PPC_INTERRUPT_*). Define them
directly like that to save some clutter. No functional change intended.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20221011204829.1641124-2-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220705145814.461723-4-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This replaces the IRQ array 'irq_inputs' with GPIO lines, the goal
being to remove 'irq_inputs' when all CPUs have been converted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220705145814.461723-2-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The timebase is allocated during spapr_realize_vcpu() and it's not
freed. This results in memory leaks when doing vcpu unplugs:
==636935==
==636935== 144 (96 direct, 48 indirect) bytes in 1 blocks are definitely lost in loss record 6
,461 of 8,135
==636935== at 0x4897468: calloc (vg_replace_malloc.c:760)
==636935== by 0x5077213: g_malloc0 (in /usr/lib64/libglib-2.0.so.0.6400.4)
==636935== by 0x507757F: g_malloc0_n (in /usr/lib64/libglib-2.0.so.0.6400.4)
==636935== by 0x93C3FB: cpu_ppc_tb_init (ppc.c:1066)
==636935== by 0x97BC2B: spapr_realize_vcpu (spapr_cpu_core.c:268)
==636935== by 0x97C01F: spapr_cpu_core_realize (spapr_cpu_core.c:337)
==636935== by 0xD4626F: device_set_realized (qdev.c:531)
==636935== by 0xD55273: property_set_bool (object.c:2273)
==636935== by 0xD523DF: object_property_set (object.c:1408)
==636935== by 0xD588B7: object_property_set_qobject (qom-qobject.c:28)
==636935== by 0xD52897: object_property_set_bool (object.c:1477)
==636935== by 0xD4579B: qdev_realize (qdev.c:333)
==636935==
This patch adds a cpu_ppc_tb_free() helper in hw/ppc/ppc.c to allow us
to free the timebase. This leak is then solved by calling
cpu_ppc_tb_free() in spapr_unrealize_vcpu().
Fixes: 6f4b5c3ec5 ("spapr: CPU hot unplug support")
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20220329124545.529145-2-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Patch created mechanically with:
$ spatch --in-place --sp-file scripts/coccinelle/use-g_new-etc.cocci \
--macro-file scripts/cocci-macro-file.h FILES...
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220315144156.1595462-4-armbru@redhat.com>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Machines which don't emulate the HDEC facility are able to use the
timer for something else. Provide functions to start and stop the
hdecr timer.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[ clg: checkpatch fixes ]
Message-Id: <20220216102545.1808018-4-npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The spapr virtual hypervisor does not require the hdecr timer.
Remove it.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20220216102545.1808018-3-npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The PowerPC 601 processor is the first generation of processors to
implement the PowerPC architecture. It was designed as a bridge
processor and also could execute most of the instructions of the
previous POWER architecture. It was found on the first Macs and IBM
RS/6000 workstations.
There is not much interest in keeping the CPU model of this
POWER-PowerPC bridge processor. We have the 603 and 604 CPU models of
the 60x family which implement the complete PowerPC instruction set.
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20220203142756.1302515-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The migration code will not look at a VMStateDescription's
minimum_version_id_old field unless that VMSD has set the
load_state_old field to something non-NULL. (The purpose of
minimum_version_id_old is to specify what migration version is needed
for the code in the function pointed to by load_state_old to be able
to handle it on incoming migration.)
We have exactly one VMSD which still has a load_state_old,
in the PPC CPU; every other VMSD which sets minimum_version_id_old
is doing so unnecessarily. Delete all the unnecessary ones.
Commit created with:
sed -i '/\.minimum_version_id_old/d' $(git grep -l '\.minimum_version_id_old')
with the one legitimate use then hand-edited back in.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
---
It missed vmstate_ppc_cpu.
This is a small cleanup to ease reading. It includes the removal of a
check done on the returned value of g_malloc0(), which can not fail.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211222064025.1541490-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220103063441.3424853-7-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The 405 timers were broken when booke support was added. Assumption
was made that the register numbers were the same but it's not :
SPR_BOOKE_TSR (0x150)
SPR_BOOKE_TCR (0x154)
SPR_40x_TSR (0x3D8)
SPR_40x_TCR (0x3DA)
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: ddd1055b07 ("PPC: booke timers")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211222064025.1541490-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220103063441.3424853-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When using u-boot as firmware with the taihu board, QEMU aborts with
this assertion:
ERROR:../accel/tcg/tcg-accel-ops.c:79:tcg_handle_interrupt: assertion failed:
(qemu_mutex_iothread_locked())
Running QEMU with "-d in_asm" shows that the crash happens when writing
to SPR 0x3f2, so we are missing to lock the iothread in the code path
here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20211006071140.565952-1-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 4d9b8ef9b5 ("target/ppc: Fix 64-bit decrementer") introduced
new int64t variables and broke the test triggering the decrementer
exception. Revert partially the change to evaluate both clause of the
if statement.
Reported-by: Coverity CID 1464061
Fixes: 4d9b8ef9b5 ("target/ppc: Fix 64-bit decrementer")
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211005053324.441132-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current way the mask is built can overflow with a 64-bit decrementer.
Use sextract64() to extract the signed values and remove the logic to
handle negative values which has become useless.
Cc: Luis Fernando Fujita Pires <luis.pires@eldorado.org.br>
Fixes: a8dafa5251 ("target/ppc: Implement large decrementer support for TCG")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210920061203.989563-5-clg@kaod.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If an unknown pin of the IRQ controller is raised, something is very
wrong in the QEMU model. It is better to abort.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210920061203.989563-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Stop including cpu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-4-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The 'running' argument from VMChangeStateHandler does not require
other value than 0 / 1. Make it a plain boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210111152020.1422021-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
A guest with enough RAM, eg. 128G, is likely to detect savevm downtime
and to complain about stalled CPUs. This happens because we re-read
the timebase just before migrating it and we thus don't account for
all the time between VM stop and pre-save.
A very similar situation was already addressed for live migration of
paused guests (commit d14f339762). Extend the logic to do the same
with savevm.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1893787
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160693010619.1111945.632640981169395440.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using -Wimplicit-fallthrough in our CFLAGS, the compiler showed warning:
hw/ppc/ppc.c: In function ‘ppc6xx_set_irq’:
hw/ppc/ppc.c:118:16: warning: this statement may fall through [-Wimplicit-fallthrough=]
118 | if (level) {
| ^
hw/ppc/ppc.c:123:9: note: here
123 | case PPC6xx_INPUT_INT:
| ^~~~
According to the discussion, a break statement needs to be added here.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201116024810.2415819-7-kuhn.chenqun@huawei.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It's been deprecated since QEMU v3.1. The 40p machine should be
used nowadays instead.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200114114617.28854-1-thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spr TBU40 is used to set the upper 40 bits of the timebase
register, present on POWER5+ and later processors.
This register can only be written by the hypervisor, and cannot be read.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Processor Utilisation of Resources Register (PURR) and Scaled
Processor Utilisation of Resources Register (SPURR) provide an estimate
of the resources used by the thread, present on POWER7 and later
processors.
Currently the [S]PURR registers simply count at the rate of the
timebase.
Preserve this behaviour but rework the implementation to store an offset
like the timebase rather than doing the calculation manually. Also allow
hypervisor write access to the register along with the currently
available read access.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[ clg: rebased on current ppc tree ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The virtual timebase register (VTB) is a 64-bit register which
increments at the same rate as the timebase register, present on POWER8
and later processors.
The register is able to be read/written by the hypervisor and read by
the supervisor. All other accesses are illegal.
Currently the VTB is just an alias for the timebase (TB) register.
Implement the VTB so that is can be read/written independent of the TB.
Make use of the existing method for accessing timebase facilities where
by the compensation is stored and used to compute the value on reads/is
updated on writes.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
[ clg: rebased on current ppc tree ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The power7_set_irq() and power9_set_irq() functions set this but it is
never used actually. Modern Book3s compatible CPUs are only supported
by the pnv and spapr machines. They have an interrupt controller, XICS
for POWER7/8 and XIVE for POWER9, whose models don't require to track
IRQ input states at the CPU level.
Drop these lines to avoid confusion.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157548862861.3650476.16622818876928044450.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a CPU is reset, QEMU makes sure no interrupt is pending by clearing
CPUPPCstate::pending_interrupts in ppc_cpu_reset(). In the case of a
complete machine emulation, eg. a sPAPR machine, an external interrupt
request could still be pending in KVM though, eg. an IPI. It will be
eventually presented to the guest, which is supposed to acknowledge it at
the interrupt controller. If the interrupt controller is emulated in QEMU,
either XICS or XIVE, ppc_set_irq() won't deassert the external interrupt
pin in KVM since it isn't pending anymore for QEMU. When the vCPU re-enters
the guest, the interrupt request is still pending and the vCPU will try
again to acknowledge it. This causes an infinite loop and eventually hangs
the guest.
The code has been broken since the beginning. The issue wasn't hit before
because accel=kvm,kernel-irqchip=off is an awkward setup that never got
used until recently with the LC92x IBM systems (aka, Boston).
Add a ppc_irq_reset() function to do the necessary cleanup, ie. deassert
the IRQ pins of the CPU in QEMU and most importantly the external interrupt
pin for this vCPU in KVM.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157548861740.3650476.16879693165328764758.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Re-read the timebase before migrate was ported from x86 commit:
6053a86fe7: kvmclock: reduce kvmclock difference on migration
The clock move makes the guest knows about the paused time between
the stop and migrate commands. This is an issue in an already-paused
VM because some side effects, like process stalls, could happen
after migration.
So, this patch checks the runstate of guest in the pre_save handler and
do not re-reads the timebase in case of paused state (cold migration).
Signed-off-by: Maxiwell S. Garcia <maxiwell@linux.ibm.com>
Message-Id: <20190711194702.26598-1-maxiwell@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Introduce a KVM helper and its stub instead of guarding the code with
CONFIG_KVM.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156051055736.224162.11641594431517798715.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
kvmppc_set_interrupt() has a stub that does nothing when CONFIG_KVM is
not defined.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156051055182.224162.15842560287892241124.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
Cleanup in the boilerplate that each target must define.
Replace ppc_env_get_cpu with env_archcpu. The combination
CPU(ppc_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We use PPC_SEGMENT_64B in various places to guard code that is specific
to 64-bit server processors compliant with arch 2.x. Consolidate the
logic in a helper macro with an explicit name.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155327783157.1283071.3747129891004927299.stgit@bahia.lan>
Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to get the CPU interrupt presenter in XIVE when the
TIMA is accessed from the indirect page.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Prior to POWER9 the decrementer was a 32-bit register which decremented
with each tick of the timebase. From POWER9 onwards the decrementer can
be set to operate in a mode called large decrementer where it acts as a
n-bit decrementing register which is visible as a 64-bit register, that
is the value of the decrementer is sign extended to 64 bits (where n is
implementation dependant).
The mode in which the decrementer operates is controlled by the LPCR_LD
bit in the logical paritition control register (LPCR).
>From POWER9 onwards the HDEC (hypervisor decrementer) was enlarged to
h-bits, also sign extended to 64 bits (where h is implementation
dependant). Note this isn't configurable and is always enabled.
On POWER9 the large decrementer and hdec are both 56 bits, as
represented by the lrg_decr_bits cpu class property. Since they are the
same size we only add one property for now, which could be extended in
the case they ever differ in the future.
We also add the lrg_decr_bits property for POWER5+/7/8 since it is used
to determine the size of the hdec, which is only generated on the
POWER5+ processor and later. On these processors it is 32 bits.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190301024317.22137-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Adds support for the Hypervisor directed interrupts in addition to the
OS ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - modified the icp_realize() and xive_tctx_realize() to take
into account explicitely the POWER9 interrupt model
- introduced a specific power9_set_irq for POWER9 ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215161648.9600-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To better reflect what this does, as it's specific to some of the
P7/P8/P9 PM states, not generic.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190215161648.9600-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
