Extend the hostfwd rule format so that the user can specify on which
host interface qemu should listen for incoming connections. If omitted,
binding will takes place against all interfaces.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
With the internal IP configuration made more flexible, we can now
enhance the user interface. This patch adds a number of new options to
"-net user": net (address and mask), host, dhcpstart, dns and smbserver.
It also renames "redir" to "hostfwd" and "channel" to "guestfwd" in
order to (hopefully) clarify their meanings. The format of guestfwd is
extended so that the user can define not only the port but also the
virtual server's IP address the forwarding starts from.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
So far a couple of slirp-related parameters were expressed via
stand-alone command line options. This it inconsistent and unintuitive.
Moreover, it prevents both dynamically reconfigured (host_net_add/
delete) and multi-instance slirp.
This patch refactors the configuration by turning -smb, -redir, -tftp
and -bootp as well as -net channel into options of "-net user". The old
stand-alone command line options are still processed, but no longer
advertised. This allows smooth migration of management applications to
to the new syntax and also the extension of that syntax later in this
series.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add an option to specify the number of MSI-X vectors for PCI NIC cards. This
can also be used to disable MSI-X, for compatibility with old qemu. This
option currently only affects virtio cards.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
2.6.30 adds a new TUNSETSNDBUF ioctl() which allows a send buffer limit
for the tap device to be specified. When this limit is reached, a tap
write() will return EAGAIN and poll() will indicate the fd isn't
writable.
This allows people to tune their setups so as to avoid e.g. UDP packet
loss when the sending application in the guest out-runs the NIC in the
host.
There is no obviously sensible default setting - a suitable value
depends mostly on the capabilities of the physical NIC through which the
packets are being sent.
Also, note that when using a bridge with netfilter enabled, we currently
never get EAGAIN because netfilter causes the packet to be immediately
orphaned. Set /proc/sys/net/bridge/bridge nf-call-iptables to zero to
disable this behaviour.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Make drive_init() accept addr=, put the value into struct DriveInfo.
Use it in all the places that create virtio-blk-pci devices:
pc_init1(), bamboo_init(), mpc8544ds_init().
Don't support addr= in third argument of monitor command pci_add and
second argument of drive_add, because that clashes with their first
arguments. Admittedly unelegant.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Make net_client_init() accept addr=, put the value into struct
NICinfo. Use it in pci_nic_init(), and remove arguments bus and
devfn.
Don't support addr= in third argument of monitor command pci_add,
because that clashes with its first argument. Admittedly unelegant.
Machines "malta" and "r2d" have a default NIC with a well-known PCI
address. Deal with that the same way as the NIC model: make
pci_nic_init() take an optional default to be used when the user
doesn't specify one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This new option may be used to disable the virtio-balloon device.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Here is an updated hardware watchdog patch, which should fix
everything that was raised about the previous version ...
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
- configure script and build system changes.
- wind up new machine type.
- add -xen-* command line options.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7219 c046a42c-6fe2-441c-8c8c-71466251a162
adds a -numa command line parameter and sets a QEMU global array with
the memory sizes. The CPU-to-node assignemnt is written into the
CPUState. If no specific values for memory and CPUs are given,
all resources will be split equally across all nodes.
This code currently support only up to 64 virtual CPUs.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7210 c046a42c-6fe2-441c-8c8c-71466251a162
Allow to establish a TCP/UDP connection redirection also via a monitor
command 'host_net_redir'. Moreover, assume TCP as connection type if
that parameter is omitted.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7204 c046a42c-6fe2-441c-8c8c-71466251a162
This patch is derived from Tristan Gingold's patch. It adds a new VLAN
client type that writes all traffic on the VLAN it is attached to into a
pcap file. Such a file can then be analyzed offline with Wireshark or
tcpdump.
Besides rebasing and some minor cleanups, the major differences to the
original version are:
- support for enabling/disabling via the monitor (host_net_add/remove)
- no special ordering of VLAN client list, qemu_send_packet now takes
care of properly ordered packets
- 64k default capturing limit (I hate tcpdump's default)
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7200 c046a42c-6fe2-441c-8c8c-71466251a162
Create a new -smbios option (x86-only) to allow binary SMBIOS entries
to be passed through to the BIOS or modify the default values of
individual fields of type 0 and 1 entries on the command line.
Binary SMBIOS entries can be generated as follows:
dmidecode -t 1 -u | grep $'^\t\t[^"]' | xargs -n1 | \
perl -lne 'printf "%c", hex($_)' > smbios_type_1.bin
These can then be passed to the BIOS using this switch:
-smbios file=smbios_type_1.bin
Command line generation supports the following syntax:
-smbios type=0[,vendor=str][,version=str][,date=str][,release=%d.%d]
-smbios type=1[,manufacturer=str][,product=str][,version=str][,serial=str]
[,uuid=$(uuidgen)][,sku=str][,family=str]
For instance, to add a serial number to the type 1 table:
-smbios type=1,serial=0123456789
Interface is extensible to support more fields/tables as needed.
aliguori: remove texi formatting from help output
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7163 c046a42c-6fe2-441c-8c8c-71466251a162
This replaces a compile time option for some targets and adds
this feature to targets which did not have a compile time option.
Add monitor command to enable or disable single step mode.
Modify monitor command "info status" to display single step mode.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7004 c046a42c-6fe2-441c-8c8c-71466251a162
Introduce a more canonical gdbstub configuration (system emulation only)
via the new switch '-gdb dev'. Keep '-s' as shorthand for
'-gdb tcp::1234'. Use the same syntax also for the corresponding monitor
command 'gdbserver'. Its default remains to listen on TCP port 1234.
Changes in v4:
- Rebased over new command line switches meta file
Changes in v3:
- Fix documentation
Changes in v2:
- Support for pipe-based like to gdb (target remote | qemu -gdb stdio)
- Properly update the qemu-doc
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6992 c046a42c-6fe2-441c-8c8c-71466251a162
On Windows default screen width for the command prompt (A.K.A. "DOS
window") is 80 chars. `-icount' help is 87 chars wide. So make it fit.
Signed-off-by: Robert Riebisch <rr@bttr-software.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6991 c046a42c-6fe2-441c-8c8c-71466251a162
Try to keep documentation about command line switches, -help text and
qemu_options table synchronized.
In true Qemu tradition, an include file is generated from single .hx file
containing all relevant information in one place. The include file is
parsed once for getting the enums, another time for getopt tables and
hird time for help messages. Texi documentation for the options is
generated from the same .hx file.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6884 c046a42c-6fe2-441c-8c8c-71466251a162
