The pseries machine code has a number of debug messages for debugging PAPR
hypercalls, dependent on DEBUG_SPAPR_HCALLS. This patch cleans these
messages up a bit, by adding __func__ to the hcall_dprintf() macro and
simplifying up a number of the individual messages accordingly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The pseries "xics" interrupt controller, like most interrupt
controllers can support both message (i.e. edge sensitive) interrupts
and level sensitive interrupts, but it needs to know which are which.
When I implemented the xics emulation for qemu, the only devices we
supported were the PAPR virtual IO devices. These devices only use
message interrupts, so they were the only ones I implemented in xics.
Since then, however, we have added support for PCI devices, which use
level sensitive interrupts. It turns out the message interrupt logic
still actually works most of the time for these, but there are
circumstances where we can lost interrupts due to the incorrect
interrupt logic.
This patch, therefore, implements the correct xics level-sensitive
interrupt logic. The type of the interrupt is set when a device
allocates a new xics interrupt.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Scripted conversion:
for file in hw/ppc*.[hc] hw/mpc8544_guts.c hw/spapr*.[hc] hw/virtex_ml507.c hw/xics.c; do
sed -i "s/CPUState/CPUPPCState/g" $file
done
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Add NUMA specific properties to guest's device tree to boot a multi-node
guests. This patch adds the following properties:
ibm,associativity
ibm,architecture-vec-5
ibm,associativity-reference-points
With this, it becomes possible to use -numa option on pseries targets.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a PCI bus to the pseries machine. This instantiates
the qemu generic PCI bus code, advertises a PCI host bridge in the
guest's device tree and implements the RTAS methods specified by PAPR
to access PCI config space. It also sets up the memory regions we
need to provide windows into the PCI memory and IO space, and
advertises those to the guest.
However, because qemu can't yet emulate an IOMMU, which is mandatory on
pseries, PCI devices which use DMA (i.e. most of them) will not work with
this code alone. Still, this is enough to support the virtio_pci device
(which probably _should_ use emulated PCI DMA, but is specced to use
direct hypervisor access to guest physical memory instead).
[agraf] remove typedef which could cause compile errors
Signed-off-by: Alexey Kardashevskiy <aik@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently there is no implementation for set-time-of-day rtas function,
which causes the following warning "setting the clock failed (-1)" on
the guest.
This patch just creates this function, get the timedate diff and store in
the papr environment, so that the correct value will be returned by
get-time-of-day.
In order to try it, just adjust the hardware time, run hwclock --systohc,
so that, on when the system runs hwclock --hctosys, the value is correctly
adjusted, i.e. the host time plus the timediff.
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Paulo Bonzini changed the original spapr code, which manually assigned irq
numbers for each virtual device, to allocate them automatically from the
device initialization. That allowed spapr virtual devices to be constructed
with -device, which is a good start. However, the way that patch worked
doesn't extend nicely for the future when we want to support devices other
than sPAPR VIO devices (e.g. virtio and PCI).
This patch rearranges the irq allocation to be global across the sPAPR
environment, so it can be used by other bus types as well.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently our implementation of the H_ENTER hypercall, which inserts a
mapping in the hash page table assumes that only ordinary memory is ever
mapped, and only permits mapping attribute bits accordingly (WIMG==0010).
However, we intend to start adding emulated IO to the pseries platform
(and real IO with PCI passthrough on kvm) which means this simple test
will no longer suffice.
This patch extends the h_enter validation code to check if the given
address is a RAM address. If it is it enforces WIMG==0010, otherwise
it assumes that it is an IO mapping and instead enforces WIMG=010x.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Right now the spapr devices cannot be instantiated with -device,
because the IRQs need to be passed to the spapr_*_create functions.
Do this instead in the bus's init wrapper.
This is particularly important with the conversion from scsi-disk
to scsi-{cd,hd} that Markus made. After his patches, if you
specify a scsi-cd device attached to an if=none drive, the default
VSCSI controller will not be created and, without qdevification,
you will not be able to add yours.
NOTE from agraf: added small compile fix
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present, the 'pseries' machine creates a flattened device tree in the
machine->init function to pass to either the guest kernel or to firmware.
However, the machine->init function runs before processing of -device
command line options, which means that the device tree so created will
be (incorrectly) missing devices specified that way.
Supplying a correct device tree is, in any case, part of the required
platform entry conditions. Therefore, this patch moves the creation and
loading of the device tree from machine->init to a reset callback. The
setup of entry point address and initial register state moves with it,
which leads to a slight cleanup.
This is not, alas, quite enough to make a fully working reset for pseries.
For that we would need to reload the firmware images, which on this
machine are loaded into RAM. It's a step in the right direction, though.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
PAPR defines an interrupt control architecture which is logically divided
into ICS (Interrupt Control Presentation, each unit is responsible for
presenting interrupts to a particular "interrupt server", i.e. CPU) and
ICS (Interrupt Control Source, each unit responsible for one or more
hardware interrupts as numbered globally across the system). All PAPR
virtual IO devices expect to deliver interrupts via this mechanism. In
Linux, this interrupt controller system is handled by the "xics" driver.
On pSeries systems, access to the interrupt controller is virtualized via
hypercalls and RTAS methods. However, the virtualized interface is very
similar to the underlying interrupt controller hardware, and similar PICs
exist un-virtualized in some other systems.
This patch implements both the ICP and ICS sides of the PAPR interrupt
controller. For now, only the hypercall virtualized interface is provided,
however it would be relatively straightforward to graft an emulated
register interface onto the underlying interrupt logic if we want to add
a machine with a hardware ICS/ICP system in the future.
There are some limitations in this implementation: it is assumed for now
that only one instance of the ICS exists, although a full xics system can
have several, each responsible for a different group of hardware irqs.
ICP/ICS can handle both level-sensitve (LSI) and message signalled (MSI)
interrupt inputs. For now, this implementation supports only MSI
interrupts, since that is used by PAPR virtual IO devices.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
On pSeries machines, operating systems can instantiate "RTAS" (Run-Time
Abstraction Services), a runtime component of the firmware which implements
a number of low-level, infrequently used operations. On logical partitions
under a hypervisor, many of the RTAS functions require hypervisor
privilege. For simplicity, therefore, hypervisor systems typically
implement the in-partition RTAS as just a tiny wrapper around a hypercall
which actually implements the various RTAS functions.
This patch implements such a hypercall based RTAS for our emulated pSeries
machine. A tiny in-partition "firmware" calls a new hypercall, which
looks up available RTAS services in a table.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This extends the "pseries" (PAPR) machine to include a virtual IO bus
supporting the PAPR defined hypercall based virtual IO mechanisms.
So far only one VIO device is provided, the vty / vterm, providing
a full console (polled only, for now).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a "pseries" machine to qemu. This aims to emulate a
logical partition on an IBM pSeries machine, compliant to the
"PowerPC Architecture Platform Requirements" (PAPR) document.
This initial version is quite limited, it implements a basic machine
and PAPR hypercall emulation. So far only one hypercall is present -
H_PUT_TERM_CHAR - so that a (write-only) console is available.
Multiple CPUs are permitted, with SMP entry handled kexec() style.
The machine so far more resembles an old POWER4 style "full system
partition" rather than a modern LPAR, in that the guest manages the
page tables directly, rather than via hypercalls.
The machine requires qemu to be configured with --enable-fdt. The
machine can (so far) only be booted with -kernel - i.e. no partition
firmware is provided.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
