The MacOS driver expects a 60.15Hz vertical blank interrupt to be generated by
the framebuffer which in turn schedules the mouse driver via the Vertical Retrace
Manager.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The monitor modes table is found by experimenting with the Monitors Control
Panel in MacOS and analysing the reads/writes. From this it can be found that
the mode is controlled by writes to the DAFB_MODE_CTRL1 and DAFB_MODE_CTRL2
registers.
Implement the first block of DAFB registers as a register array including the
existing sense register, the newly discovered control registers above, and also
the DAFB_MODE_VADDR1 and DAFB_MODE_VADDR2 registers which are used by NetBSD to
determine the current video mode.
These experiments also show that the offset of the start of video RAM and the
stride can change depending upon the monitor mode, so update macfb_draw_graphic()
and both the BI_MAC_VADDR and BI_MAC_VROW bootinfo for the q800 machine
accordingly.
Finally update macfb_common_realize() so that only the resolution and depth
supported by the display type can be specified on the command line, and add an
error hint showing the list of supported resolutions and depths if the user tries
to specify an invalid display mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since the available resolutions and colour depths are determined by the attached
display type, add a qdev property to allow the display type to be specified.
The main resolutions of interest are high resolution 1152x870 with 8-bit colour
and SVGA resolution up to 800x600 with 24-bit colour so update the q800 machine
to allow high resolution mode if specified and otherwise fall back to SVGA.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS toolbox ROM uses the monitor sense to detect the display type and then
offer a fixed set of resolutions and colour depths accordingly. Implement the
monitor sense using information found in Apple Technical Note HW26: "Macintosh
Quadra Built-In Video" along with some local experiments.
Since the default configuration is 640 x 480 with 8-bit colour then hardcode
the sense register to return MACFB_DISPLAY_VGA for now.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Target lm32 was deprecated in commit d849800512, v5.2.0. See there
for rationale.
Some of its code lives on in device models derived from milkymist
ones: hw/char/digic-uart.c and hw/display/bcm2835_fb.c.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-2-armbru@redhat.com>
Acked-by: Michael Walle <michael@walle.cc>
[Trivial conflicts resolved, reST markup fixed]
Introduce a symbol which can be used to prevent display modules which
need vga support being loaded into system emulators with CONFIG_VGA=n.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-16-kraxel@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
contrib/plugins/hotblocks.c
contrib/plugins/hotpages.c
contrib/plugins/howvec.c
contrib/plugins/lockstep.c
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
target/s390x/gen-features.c
tests/fp/platform.h
tests/migration/s390x/a-b-bios.c
tests/plugin/bb.c
tests/plugin/empty.c
tests/plugin/insn.c
tests/plugin/mem.c
tests/test-rcu-simpleq.c
tests/test-rcu-slist.c
tests/test-rcu-tailq.c
tests/uefi-test-tools/UefiTestToolsPkg/BiosTablesTest/BiosTablesTest.c
contrib/plugins/, tests/plugin/, and tests/test-rcu-slist.c appear not
to include osdep.h intentionally. The remaining reverts are the same
as in commit bbfff19688.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201113061216.2483385-1-armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Replace dpi with width_mm/height_mm in qemu_edid_info.
Use it when set (non-zero) to compute the DPI and generate the EDID.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20200927145751.365446-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the existing class type checking macros to be consistent
with the type name and instance type checking macro. Use a
NUBUS_MACFB prefix instead of MACFB_NUBUS.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-44-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We use the Object type all over the place.
Forward declare it in "qemu/typedefs.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200504115656.6045-2-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When trying to consume the DEFINE_EDID_PROPERTIES() macro
by including "hw/display/edid.h", we get this build failure:
include/hw/display/edid.h:24:5: error: implicit declaration of
function ‘DEFINE_PROP_UINT32’ [-Werror=implicit-function-declaration]
24 | DEFINE_PROP_UINT32("xres", _state, _edid_info.prefx, 0), \
| ^~~~~~~~~~~~~~~~~~
Headers should be self-contained, and one shouldn't have to
dig to find the missing headers.
In this case "hw/qdev-properties.h" is missing. Add it.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200526062252.19852-2-f4bug@amsat.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This reverts commit f79081b4b7.
Patch has broken byteorder handling: RAMFBCfg fields are in bigendian
byteorder, the reset function doesn't care so native byteorder is used
instead. Given this went unnoticed so far the feature is obviously
unused, so just revert the patch.
Cc: Hou Qiming <hqm03ster@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20200429115236.28709-2-kraxel@redhat.com
The license is the 'GNU General Public License v2.0 or later',
not 'and':
This program is free software; you can redistribute it and/ori
modify it under the terms of the GNU General Public License as
published by the Free Software Foundation; either version 2 of
the License, or (at your option) any later version.
Fix the license comment.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200312213455.15854-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds support for a graphic framebuffer device.
This device can be added as a sysbus device or as a NuBus device.
It is accessed as a framebuffer but the color palette can be set.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20191026164546.30020-9-laurent@vivier.eu>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
hw/hw.h used to include headers hardware emulation "usually" needs.
The previous commits removed all but one of them, to good effect.
Only qom/object.h is left. Remove that one, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-18-armbru@redhat.com>
Drop unnecessary inclusions from headers. Downgrade a few more to
exec/hwaddr.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-17-armbru@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Back in 2016, we discussed[1] rules for headers, and these were
generally liked:
1. Have a carefully curated header that's included everywhere first. We
got that already thanks to Peter: osdep.h.
2. Headers should normally include everything they need beyond osdep.h.
If exceptions are needed for some reason, they must be documented in
the header. If all that's needed from a header is typedefs, put
those into qemu/typedefs.h instead of including the header.
3. Cyclic inclusion is forbidden.
This patch gets include/ closer to obeying 2.
It's actually extracted from my "[RFC] Baby steps towards saner
headers" series[2], which demonstrates a possible path towards
checking 2 automatically. It passes the RFC test there.
[1] Message-ID: <87h9g8j57d.fsf@blackfin.pond.sub.org>
https://lists.nongnu.org/archive/html/qemu-devel/2016-03/msg03345.html
[2] Message-Id: <20190711122827.18970-1-armbru@redhat.com>
https://lists.nongnu.org/archive/html/qemu-devel/2019-07/msg02715.html
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-2-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Add new properties to allow setting the maximum display resolution.
Resolutions larger than that will not be included in the mode list.
In linux guests xrandr can be used to list modes.
Note: The existing xres and yres properties set the preferred display
resolution, i.e. the mode should be first in the mode list and guests
should use it by default.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190607083429.31943-1-kraxel@redhat.com
This is the common header guard idiom:
/*
* File comment
*/
#ifndef GUARD_SYMBOL_H
#define GUARD_SYMBOL_H
... actual contents ...
#endif
A few of our headers have some #include before the guard.
target/tilegx/spr_def_64.h has #ifndef __DOXYGEN__ outside the guard.
A few more have the #define elsewhere.
Change them to match the common idiom. For spr_def_64.h, that means
dropping #ifndef __DOXYGEN__. While there, rename guard symbols to
make scripts/clean-header-guards.pl happy.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190604181618.19980-2-armbru@redhat.com>
[Rebased with conflicts resolved automatically]
If xres / yres were specified in QEMU command line, write them as an initial
resolution to the fw-config space on guest reset, which a later BIOS / OVMF
patch can take advantage of.
Signed-off-by: HOU Qiming <hqm03ster@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-id: 20190513115731.17588-4-marcel.apfelbaum@gmail.com
[fixed malformed patch]
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Move it together with the other EDID code. hw/i2c should only
include the core and the adapters, not the slaves.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190325155923.30987-1-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add an entries the Blizzard device in MAINTAINERS.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-6-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the complexity of milkymist_tmu2_create() into the
source file. Doing so we avoid to include the X11/OpenGL
headers in all LM32 devices, and we also avoid the duplicate
declaration of glx_fbconfig_attr[] (it is already declared
in hw/display/milkymist-tmu2.c).
Since TYPE_MILKYMIST_TMU2 is now accessible, use it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190130120005.23123-5-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
"EMU" actually is "Emulex Corporation", so not a good idea to use that
by default. Lets use the Red Hat vendor id instead, which is in line
with the pci ids which are allocated from Red Hat vendor ids too.
Vendor list is available from http://www.uefi.org/pnp_id_list
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20181005091934.12143-1-kraxel@redhat.com
Create a io region for an EDID data block.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180925075646.25114-4-kraxel@redhat.com
Helper function to figure the size of a edid blob, by checking how many
extensions are present. Both the base edid blob and the extensions are
128 bytes in size.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180925075646.25114-3-kraxel@redhat.com
EDID is a metadata format to describe monitors. On physical hardware
the monitor has an eeprom with that data block which can be read over
i2c bus.
On a linux system you can usually find the EDID data block in
/sys/class/drm/$card/$connector/edid. xorg ships a edid-decode utility
which you can use to turn the blob into readable form.
I think it would be a good idea to use EDID for virtual displays too.
Needs changes in both qemu and guest kms drivers. This patch is the
first step, it adds an generator for EDID blobs to qemu. Comes with a
qemu-edid test tool included.
With EDID we can pass more information to the guest. Names and serial
numbers, so the guests display configuration has no boring "Unknown
Monitor". List of video modes. Display resolution, pretty important
in case we want add HiDPI support some day.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180925075646.25114-2-kraxel@redhat.com
Validate the config settings that the guest tries to set.
The wiki page documentation is not really accurate here:
generally rather than failing requests to set bad parameters,
the hardware will just clip them to something sensible.
Validate the most important parameters: sizes and
the viewport offsets. This prevents the framebuffer
code from trying to read out-of-range memory.
In the property handling code, we validate the new parameters every
time we encounter a tag that sets them. This means we validate the
config multiple times if the request includes multiple config-setting
tags, but the code would require significant restructuring to do a
validation only once but still return the clipped settings for
get-parameter tags and the buffer allocation tag.
Validation of settings made via the older bcm2835_fb_mbox_push()
function will be done in the next commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-8-peter.maydell@linaro.org
The raspi framebuffir in bcm2835_fb supports the definition
of a virtual "viewport", which is smaller than the full
physical framebuffer size and at an adjustable offset within
it. Only the viewport area is sent to the screen. This allows
the guest to do things like double buffering, or scrolling
by adjusting the viewport origin. Currently QEMU doesn't
implement this at all.
Add support for this feature:
* the property mailbox code needs to distinguish the
virtual width/height from the physical width/height
* the framebuffer code needs to do something with the
virtual width/height/origin information
Note that the wiki documentation on the semantics of the
virtual and physical height and width has it the wrong way
around -- the virtual size is the size of the allocated
buffer, and the physical size is the size of the display,
so the virtual size is always the same as or larger than
the physical.
If the viewport size is set smaller than the physical
screen size, we ignore the viewport settings completely
and just display the physical screen area.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-7-peter.maydell@linaro.org
Abstract out the calculation of the pitch and size of the
framebuffer into functions that operate on the BCM2835FBConfig
struct -- these are about to get a little more complicated
when we add support for virtual and physical sizes differing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-6-peter.maydell@linaro.org
The bcm2835_fb's initial resolution and other parameters are set
via QOM properties. We should reset to those initial values on
device reset, which means we need to save the QOM property
values somewhere that they are not overwritten by guest
changes to the framebuffer configuration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-5-peter.maydell@linaro.org
The BCM2835FBState struct has a 'pitch' field which is a
cached copy of xres * (bpp >> 3), and a 'size' field which is
a cached copy of pitch * yres. However we don't actually do
anything with these fields; delete them. We retain the
now-unused slots in the VMState struct for migration
compatibility.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-4-peter.maydell@linaro.org
Refactor the fb property setting code so that rather than
using a set of pointers to local variables to track
whether a config value has been updated in the current
mbox and if so what its new value is, we just copy
all the current settings of the fb at the start, and
then update that copy as we go along, before asking
the fb to switch to it at the end.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-3-peter.maydell@linaro.org
The handling of framebuffer properties in the bcm2835_property code
is a bit clumsy, because for each of the many fb related properties
we try to track the value we're about to set and whether we're going
to be setting a value, and then we hand all the new values off
to the framebuffer via a function which takes them all as separate
arguments. It would be simpler if the property code could easily
copy all the framebuffer's current settings, update them with
the new specified values and then ask the framebuffer to switch
to the new set.
As the first part of this refactoring, pull all the fb config
settings fields in BCM2835FBState out into their own struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-2-peter.maydell@linaro.org
The boot framebuffer is expected to be configured by the firmware, so it
uses fw_cfg as interface. Initialization goes as follows:
(1) Check whenever etc/ramfb is present.
(2) Allocate framebuffer from RAM.
(3) Fill struct RAMFBCfg, write it to etc/ramfb.
Done. You can write stuff to the framebuffer now, and it should appear
automagically on the screen.
Note that this isn't very efficient because it does a full display
update on each refresh. No dirty tracking. Dirty tracking would have
to be active for the whole ram slot, so that wouldn't be very efficient
either. For a boot display which is active for a short time only this
isn't a big deal. As permanent guest display something better should be
used (if possible).
This is the ramfb core code. Some windup is needed for display devices
which want have a ramfb boot display.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20180613122948.18149-2-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Create a new header file, move the bochs vbe dispi interface
defines to it, so they can be used outside vga code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180522165058.15404-2-kraxel@redhat.com
and remove the old i386/pc dependency.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
