The SCU is a collection of chip-level control registers that manage the
various functions supported by ASPEED SoCs. Typically the bits control
interactions with clocks, external hardware or reset behaviour, and we
can largly take a hands-off approach to reads and writes.
Firmware makes heavy use of the state to determine how to boot, but the
reset values vary from SoC to SoC (eg AST2400 vs AST2500). A qdev
property is exposed so that the integrating SoC model can configure the
silicon revision, which in-turn selects the appropriate reset values.
Further qdev properties are exposed so the board model can configure the
board-dependent hardware strapping.
Almost all provided AST2400 reset values are specified by the datasheet.
The notable exception is SOC_SCRATCH1, where we mark the DRAM as
successfully initialised to avoid unnecessary dark corners in the SoC's
u-boot support.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1466744305-23163-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: drop unnecessary inttypes.h include]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The tmp105 test is currently not executed since the following
line in the Makefile overwrites the check-qtest-arm-y variable
instead of extending it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1466760306-21849-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence GEM data sheet says:
"Wrap - marks last descriptor in transmit buffer descriptor list. This
can be set for any buffer within the frame."
which seems to imply that when the wrap bit is set so is the last bit.
Previously if the wrap bit is set, but the last is not then QEMU will
enter an infinite loop.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Reported-by: P J P <ppandit@redhat.com>
Message-id: eb23f15c67989ea6a53609dc66568399dadf52a7.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A guest can write zero to the DMACFG resulting in an infinite loop when
it reaches the while(bytes_to_copy) loop.
To avoid this issue enforce a minimum size for the RX buffer. Hardware
does not have this enforcement and relies on the guest to set a non-zero
value.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Reported-by: P J P <ppandit@redhat.com>
Message-id: 84bb1c391b833275da3f573d4972920cea34c188.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If qemu_chr_fe_write() returns an error (represented by a negative
number) we should skip incrementing the count and initiating a
memmove().
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 667e5dc534d33338fcfc2471e5aa32fe7cbd13dc.1466546703.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are spotted by coverity 1356936 and 1356937.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1466387717-13740-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Small queue this time. Main reason for sending it is the pair of
patches to fix up the new cpu hotplug model used on Power to what
should be an actually usable state. There's also a small BookE bugfix
and a XICS trivial cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ltJi
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.7-20160627' into staging
ppc patch queue for 2016-06-27
Small queue this time. Main reason for sending it is the pair of
patches to fix up the new cpu hotplug model used on Power to what
should be an actually usable state. There's also a small BookE bugfix
and a XICS trivial cleanup.
# gpg: Signature made Mon 27 Jun 2016 06:28:37 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.7-20160627:
qapi: keep names in 'CpuInstanceProperties' in sync with struct CPUCore
qapi: Report support for -device cpu hotplug in query-machines
ppc/xics: Remove unused xics_set_irq_type()
target-ppc: ppce500_spin.c uses SPR_PIR, should use SPR_BOOKE_PIR
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
struct CPUCore uses 'id' suffix in the property name. As docs for
query-hotpluggable-cpus state that the cpu core properties should be
passed back to device_add by management in case new members are added
and thus the names for the fields should be kept in sync.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
[dwg: Removed a duplicated word in comment]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For management apps it's very useful to know whether the selected
machine type supports cpu hotplug via the new -device approach. Using
the presence of 'query-hotpluggable-cpus' alone is not enough as a
witness.
Add a property to 'MachineInfo' called 'hotpluggable-cpus' that will
report the presence of this feature.
Example of output:
{
"hotpluggable-cpus": false,
"name": "mac99",
"cpu-max": 1
},
{
"hotpluggable-cpus": true,
"name": "pseries-2.7",
"is-default": true,
"cpu-max": 255,
"alias": "pseries"
},
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[dwg: Adjusted for context to apply without original series]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ppce500_spin.c uses SPR_PIR to initialize the spin table, however on
Book E processors the correct SPR is SPR_BOOKE_PIR.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add preprocessor definition of FCR31's FS bit, and update related
code for setting this bit.
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This patch implements read and write access rules for Mips floating
point control and status register (FCR31). The change can be divided
into following parts:
- Add fields that will keep FCR31's R/W bitmask in procesor
definitions and processor float_status structure.
- Add appropriate value for FCR31's R/W bitmask for each supported
processor.
- Add function for setting snan_bit_is_one, and integrate it in
appropriate places.
- Modify handling of CTC1 (case 31) instruction to use FCR31's R/W
bitmask.
- Modify handling user mode executables for Mips, in relation to the
bit EF_MIPS_NAN2008 from ELF header, that is in turn related to
reading and writing to FCR31.
- Modify gdb behavior in relation to FCR31.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
New set of helpers for handling nan2008-syle versions of instructions
<CEIL|CVT|FLOOR|ROUND|TRUNC>.<L|W>.<S|D>, for Mips R6.
All involved instructions have float operand and integer result. Their
core functionality is implemented via invocations of appropriate SoftFloat
functions. The problematic cases are when the operand is a NaN, and also
when the operand (float) is out of the range of the result.
Here one can distinguish three cases:
CASE MIPS-A: (FCR31.NAN2008 == 1)
1. Operand is a NaN, result should be 0;
2. Operand is larger than INT_MAX, result should be INT_MAX;
3. Operand is smaller than INT_MIN, result should be INT_MIN.
CASE MIPS-B: (FCR31.NAN2008 == 0)
1. Operand is a NaN, result should be INT_MAX;
2. Operand is larger than INT_MAX, result should be INT_MAX;
3. Operand is smaller than INT_MIN, result should be INT_MAX.
CASE SoftFloat:
1. Operand is a NaN, result is INT_MAX;
2. Operand is larger than INT_MAX, result is INT_MAX;
3. Operand is smaller than INT_MIN, result is INT_MIN.
Current implementation of <CEIL|CVT|FLOOR|ROUND|TRUNC>.<L|W>.<S|D>
implements case MIPS-B. This patch relates to case MIPS-A. For case
MIPS-A, only return value for NaN-operands should be corrected after
appropriate SoftFloat library function is called.
Related MSA instructions FTRUNC_S and FTINT_S already handle well
all cases, in the fashion similar to the code from this patch.
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com:
* removed a statement from the description which caused slight confusion]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Updated handling of instructions <ABS|NEG>.<S|D>. Note that legacy
(pre-abs2008) ABS and NEG instructions are arithmetic (and, therefore,
any NaN operand causes signaling invalid operation), while abs2008
ones are non-arithmetic, always and only changing the sign bit, even
for NaN-like operands. Details on these instructions are documented
in [1] p. 35 and 359.
Implementation-wise, abs2008 versions are implemented without helpers,
for simplicity and performance sake.
[1] "MIPS Architecture For Programmers Volume II-A:
The MIPS64 Instruction Set Reference Manual",
Imagination Technologies LTD, Revision 6.04, November 13, 2015
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Function msa_reset() is updated so that flag snan_bit_is_one is
properly set to 0.
By applying this patch, a number of incorrect MSA behaviors that
require IEEE 754-2008 compliance will be fixed. Those are behaviors
that (up to the moment of applying this patch) did not get the desired
functionality from SoftFloat library with respect to distinguishing
between quiet and signaling NaN, getting default NaN values (both
quiet and signaling), establishing if a floating point number is NaN
or not, etc.
Two examples:
* FMAX, FMIN will now correctly detect and propagate NaNs.
* FCLASS.D ans FCLASS.S will now correcty detect NaN flavors.
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Missing values EF_MIPS_FP64 and EF_MIPS_NAN2008 added.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Only for Mips platform, and only for cases when snan_bit_is_one is 0,
correct the order of argument comparisons in pickNaNMulAdd().
For more info, see [1], page 53, section "3.5.3 NaN Propagation".
[1] "MIPS Architecture for Programmers Volume IV-j:
The MIPS32 SIMD Architecture Module",
Imagination Technologies LTD, Revision 1.12, February 3, 2016
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[leon.alrae@imgtec.com:
* reworded the subject of the patch
* swapped if/else code blocks to match the commit description]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Only for Mips platform, and only for cases when snan_bit_is_one is 0,
correct default NaN values (in their 16-, 32-, and 64-bit flavors).
For more info, see [1], page 84, Table 6.3 "Value Supplied When a New
Quiet NaN Is Created", and [2], page 52, Table 3.7 "Default NaN
Encodings".
[1] "MIPS Architecture For Programmers Volume II-A:
The MIPS64 Instruction Set Reference Manual",
Imagination Technologies LTD, Revision 6.04, November 13, 2015
[2] "MIPS Architecture for Programmers Volume IV-j:
The MIPS32 SIMD Architecture Module",
Imagination Technologies LTD, Revision 1.12, February 3, 2016
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
fpu/softfloat-specialize.h is the most critical file in SoftFloat
library, since it handles numerous differences between platforms in
relation to floating point arithmetics. This patch makes the code
in this file more consistent format-wise, and hopefully easier to
debug and maintain.
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This patch modifies SoftFloat library so that it can be configured in
run-time in relation to the meaning of signaling NaN bit, while, at the
same time, strictly preserving its behavior on all existing platforms.
Background:
In floating-point calculations, there is a need for denoting undefined or
unrepresentable values. This is achieved by defining certain floating-point
numerical values to be NaNs (which stands for "not a number"). For additional
reasons, virtually all modern floating-point unit implementations use two
kinds of NaNs: quiet and signaling. The binary representations of these two
kinds of NaNs, as a rule, differ only in one bit (that bit is, traditionally,
the first bit of mantissa).
Up to 2008, standards for floating-point did not specify all details about
binary representation of NaNs. More specifically, the meaning of the bit
that is used for distinguishing between signaling and quiet NaNs was not
strictly prescribed. (IEEE 754-2008 was the first floating-point standard
that defined that meaning clearly, see [1], p. 35) As a result, different
platforms took different approaches, and that presented considerable
challenge for multi-platform emulators like QEMU.
Mips platform represents the most complex case among QEMU-supported
platforms regarding signaling NaN bit. Up to the Release 6 of Mips
architecture, "1" in signaling NaN bit denoted signaling NaN, which is
opposite to IEEE 754-2008 standard. From Release 6 on, Mips architecture
adopted IEEE standard prescription, and "0" denotes signaling NaN. On top of
that, Mips architecture for SIMD (also known as MSA, or vector instructions)
also specifies signaling bit in accordance to IEEE standard. MSA unit can be
implemented with both pre-Release 6 and Release 6 main processor units.
QEMU uses SoftFloat library to implement various floating-point-related
instructions on all platforms. The current QEMU implementation allows for
defining meaning of signaling NaN bit during build time, and is implemented
via preprocessor macro called SNAN_BIT_IS_ONE.
On the other hand, the change in this patch enables SoftFloat library to be
configured in run-time. This configuration is meant to occur during CPU
initialization, at the moment when it is definitely known what desired
behavior for particular CPU (or any additional FPUs) is.
The change is implemented so that it is consistent with existing
implementation of similar cases. This means that structure float_status is
used for passing the information about desired signaling NaN bit on each
invocation of SoftFloat functions. The additional field in float_status is
called snan_bit_is_one, which supersedes macro SNAN_BIT_IS_ONE.
IMPORTANT:
This change is not meant to create any change in emulator behavior or
functionality on any platform. It just provides the means for SoftFloat
library to be used in a more flexible way - in other words, it will just
prepare SoftFloat library for usage related to Mips platform and its
specifics regarding signaling bit meaning, which is done in some of
subsequent patches from this series.
Further break down of changes:
1) Added field snan_bit_is_one to the structure float_status, and
correspondent setter function set_snan_bit_is_one().
2) Constants <float16|float32|float64|floatx80|float128>_default_nan
(used both internally and externally) converted to functions
<float16|float32|float64|floatx80|float128>_default_nan(float_status*).
This is necessary since they are dependent on signaling bit meaning.
At the same time, for the sake of code cleanup and simplicity, constants
<floatx80|float128>_default_nan_<low|high> (used only internally within
SoftFloat library) are removed, as not needed.
3) Added a float_status* argument to SoftFloat library functions
XXX_is_quiet_nan(XXX a_), XXX_is_signaling_nan(XXX a_),
XXX_maybe_silence_nan(XXX a_). This argument must be present in
order to enable correct invocation of new version of functions
XXX_default_nan(). (XXX is <float16|float32|float64|floatx80|float128>
here)
4) Updated code for all platforms to reflect changes in SoftFloat library.
This change is twofolds: it includes modifications of SoftFloat library
functions invocations, and an addition of invocation of function
set_snan_bit_is_one() during CPU initialization, with arguments that
are appropriate for each particular platform. It was established that
all platforms zero their main CPU data structures, so snan_bit_is_one(0)
in appropriate places is not added, as it is not needed.
[1] "IEEE Standard for Floating-Point Arithmetic",
IEEE Computer Society, August 29, 2008.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Tested-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Tested-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[leon.alrae@imgtec.com:
* cherry-picked 2 chunks from patch #2 to fix compilation warnings]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
nvdimm label support
cpu acpi hotplug rework
virtio rework
misc cleanups and fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXbMooAAoJECgfDbjSjVRp0fYIAJ8hWf4im66Y/+Tyk957XJJt
GZ4axsa21/k6gbVZxrx6jAUwjzWEqLeXKiZ79YMVtE1SIUhSqs1exhfrGhNNXjvn
t46utHtwMnb6XPb2ru4+bQr1u+NN7RtTmi9Sd3uonWnIGXFrA69QeFejCVcEcSvJ
uiwjkODmPW0+7gRLa4SP80iS1E6nSA96Z7aOMdbQNMIW1HRVulkiXO2lwg8yz5D0
QkTqMUk/VK22RFnskDLDnTjXTADSx8L1ipjSkr4D92jTJ06ZLklVe9vijbpmd85k
ScLRNSgMstkrCe9wuP1CWZeiAG+t7QLBRJWQh7kSk7xWJONP9ShZRX4MbCl7mwI=
=XqTl
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
nvdimm label support
cpu acpi hotplug rework
virtio rework
misc cleanups and fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 24 Jun 2016 06:50:32 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (34 commits)
virtio-bus: remove old set_host_notifier callback
virtio-mmio: convert to ioeventfd callbacks
virtio-pci: convert to ioeventfd callbacks
virtio-ccw: convert to ioeventfd callbacks
virtio-bus: have callers tolerate new host notifier api
virtio-bus: common ioeventfd infrastructure
pc: acpi: drop intermediate PCMachineState.node_cpu
acpi-test-data: update expected
pc: use new CPU hotplug interface since 2.7 machine type
acpi: cpuhp: add cpu._OST handling
acpi: cpuhp: implement hot-remove parts of CPU hotplug interface
acpi: cpuhp: implement hot-add parts of CPU hotplug interface
pc: acpi: introduce AcpiDeviceIfClass.madt_cpu hook
acpi: cpuhp: add CPU devices AML with _STA method
pc: piix4/ich9: add 'cpu-hotplug-legacy' property
docs: update ACPI CPU hotplug spec with new protocol
i386: pci-assign: Fix MSI-X table size
docs: add NVDIMM ACPI documentation
nvdimm acpi: support Set Namespace Label Data function
nvdimm acpi: support Get Namespace Label Data function
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All users have been converted to the new ioevent callbacks.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert to the new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert to new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Have vhost and dataplane use the new api for transports that
have been converted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a set of ioeventfd callbacks on the virtio-bus level
that can be implemented by the individual transports. At the
virtio-bus level, do common handling for host notifiers (which
is actually most of it).
Two things of note:
- When setting the host notifier, we only switch from/to the
generic ioeventfd handler. This fixes a latent bug where we
had no ioeventfd assigned for a certain window.
- We always iterate over all possible virtio queues, even though
ccw (currently) has a lower limit. It does not really matter
here.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCMachineState.node_cpu was used for mapping APIC ID
to numa node id as CPU entries in SRAT used to be
built on sparse APIC ID bitmap (up to apic_id_limit).
However since commit
5803fce pc: acpi: SRAT: create only valid processor lapic entries
CPU entries in SRAT aren't build using apic bitmap
but using 0..maxcpus index instead which is also used
for creating numa_info[x].node_cpu map.
So instead of doing useless intermediate conversion from
1. node by cpu index -> node by apic id
i.e. numa_info[x].node_cpu -> PCMachineState.node_cpu
2. apic id -> srat entry PMX
PCMachineState.node_cpu[apic id] -> PMX value
use numa_info[x].node_cpu map directly like ARM does and do
1. numa_info[x].node_cpu -> PMX value using index
in range 0..maxcpus
and drop not necessary PCMachineState.node_cpu and related
code.
That also removes the last (not counting legacy hotplug)
dependency of ACPI code on apic_id_limit and need to allocate
huge sparse PCMachineState.node_cpu array in case of 32-bit
APIC IDs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For compatibility reasons PC/Q35 will start with legacy
CPU hotplug interface by default but with new CPU hotplug
AML code since 2.7 machine type. That way legacy firmware
that doesn't use QEMU generated ACPI tables will be
able to continue using legacy CPU hotplug interface.
While new machine type, with firmware supporting QEMU
provided ACPI tables, will generate new CPU hotplug AML,
which will switch to new CPU hotplug interface when
guest OS executes its _INI method on ACPI tables
loading.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds HW and AML parts for CPU_Device._OST method
handling to allow OSPM reports status of hot-(un)plug
operation.
And extends QMP command query-acpi-ospm-status to report
CPU's OST info along with already reported PC-DIMM devices.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds hw registers needed for handling CPU hot-remove and
corresponding AML methods to request and eject a CPU with
necessary hotplug callbacks in pc,piix4,ich9 code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds hw registers needed for handling CPU hot-add and
corresponding AML methods to handle hot-add events on
guest side.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add madt_cpu callback to AcpiDeviceIfClass and use
it for generating LAPIC MADT entries for CPUs.
Later it will be used for generating x2APIC
entries in case of more than 255 CPUs and also
would be reused by ARM target when ACPI CPU hotplug
is introduced there.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds CPU objects to DSDT with _STA method
and QEMU side of CPU hotplug interface initialization
with registers sufficient to handle _STA requests,
including necessary hotplug callbacks in piix4,ich9 code.
Hot-(un)plug hw/acpi parts will be added by
corresponding follow up patches.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be used to select which hotplug call-back is called
and for switching from legacy mode into new one.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add description of new CPU hotplug interface.
To switch from from legacy mode into new mode use fact
that write accesses into CPU present bitmap were never
used before and were ignored by QEMU.
So use it to as a way to switch from legacy mode.
That way pc/q35 machine starts in legacy mode and
QEMU generated ACPI tables will switch to new CPU
hotplug interface during runtime.
In case QEMU is started with legacy BIOS (that doesn't
support QEMU generated ACPI tables), legacy CPU hotplug
will remain active and could be used by BIOS built in
ACPI tables for CPU hotplug.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The current code creates a whole page mmio region for the MSI-X table
size.
However, the page containing the MSI-X table may contain other registers
not related to MSI-X. Creating an mmio region for the whole page masks
such registers and may break drivers in the guest OS.
Since maximal number of entries is known, use that instead to deduce the
table size when setting up the mmio region.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It describes the basic concepts of NVDIMM ACPI and the interfaces
between QEMU and the ACPI BIOS
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Function 6 is used to set Namespace Label Data
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Function 5 is used to get Namespace Label Data
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Function 4 is used to get Namespace label size
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently only revision 1 is supported
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It separates the operations between root device and nvdimm devices
in order to introducing label functions support for nvdimm device
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Check arg0 which indicates UUID to see if it is valid
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Check if the input Arg3 is valid then store it into ARG3 if it is
needed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
