This function reads the value of the PCI_CLASS_PROG register for PCI IDE
controllers and configures the PCI BARs and/or IDE ioports accordingly.
In the case where we switch to legacy mode, the PCI BARs are set to return zero
(as suggested in the "PCI IDE Controller" specification), the legacy IDE ioports
are enabled, and the PCI interrupt pin cleared to indicate legacy IRQ routing.
Conversely when we switch to native mode, the legacy IDE ioports are disabled
and the PCI interrupt pin set to indicate native IRQ routing. The contents of
the PCI BARs are unspecified, but this is not an issue since if a PCI IDE
controller has been switched to native mode then its BARs will need to be
programmed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-3-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230531211043.41724-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Every TYPE_PCI_IDE device performs the same not-so-trivial bit manipulation by
copy'n'paste code. Extract this into bmdma_status_writeb(), mirroring
bmdma_cmd_writeb().
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20230531211043.41724-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Every invocation of bmdma_init() is followed by `d->bmdma[i].bus = &d->bus[i]`.
Resolve this redundancy by extracting it into bmdma_init().
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Exposing the legacy IDE interrupts as GPIOs allows them to be connected in the
parent device through qdev_connect_gpio_out(), i.e. without accessing private
data of TYPE_PCI_IDE.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The function is only used inside ide/pci.c, so doesn't need to be exported.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-18-philmd@linaro.org>
idebus_active_if() operates on a IDEBus; rename it as
ide_bus_active_if() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/idebus_active_if/ide_bus_active_if/g' \
$(git grep -l idebus_active_if)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-16-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_create_drive() operates on a IDEBus; rename it as
ide_bus_create_drive() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_create_drive/ide_bus_create_drive/g' \
$(git grep -wl ide_create_drive)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-12-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Only include "hw/irq.h" where appropriate.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-10-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
It's the Control register, part of the Control block -- Command is
misleading here. Rename all related functions and constants.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Handlers don't need to modify the IDEDMA structure.
Make it const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200512194917.15807-1-philmd@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The pci_ide_create_devs() function takes a hd_table parameter but all
callers just pass what ide_drive_get() returns so we can do it locally
simplifying callers and removing hd_table parameter.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: e9713fdded4d212fa68ed03b844e531934226a6f.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
Spaces are required around a + operator and if statements should have
braces even for single line. Also make it simpler by reversing the
condition instead of breaking the loop.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 0d50336ab26a56240c8c17ca1ec6135a4092fcc9.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
This removes pci_piix3_ide_init() and pci_piix3_xen_ide_init()
functions similar to clean up done to other ide devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: adddfa21552783020d64e1314318cab6d24362c3.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The io mem ops callbacks are not specific to CMD646 but really follow
the PCI IDE spec so move these from cmd646.c to pci.c to allow other
PCI IDE implementations to use them.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: a2b1b2b74afdc78330b8b75605687f683a249635.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
These files don't seem to do anything related to ISA directly, so
there is no need to include isa.h here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1546615943-16274-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Remove those unneeded includes to speed up the compilation
process a little bit. (Continue 7eceff5b5a cleanup)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-13-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
and remove a duplicated include
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Remove the DEBUG_IDE preprocessor definition with something more
appropriately flexible, using the trace-events subsystem.
This will be less prone to bitrot and will more effectively allow
us to target just the functions we care about.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170901001502.29915-2-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
If the migration occurs after the IDE DMA has been set up but before it
has been initiated, the state gets lost upon save/restore. Specifically,
->dma_cb callback gets cleared, so, when the guest eventually starts bus
mastering, the DMA never completes, causing the guest to time out the
operation.
OTOH all the infrastructure is already in place to restart the DMA if
the migration happens while the DMA is in progress.
So reuse that infrastructure, by setting bus->error_status based on
->dma_cmd in pre_save if ->dma_cb callback is already set but DMAING is
clear. This will indicate the need for restart and make sure ->dma_cb
is restored in ide_restart_bh(); howeover since DMAING is clear the state
upon restore will be exactly "ready for DMA" as before the save.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1459924806-306-2-git-send-email-den@openvz.org
Signed-off-by: John Snow <jsnow@redhat.com>
Buffered DMA cancellation was added to ATAPI devices and implemented
for the BMDMA HBA. Move the code over to common IDE code and allow
it to be used for any HBA.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-4-git-send-email-jsnow@redhat.com
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-17-git-send-email-peter.maydell@linaro.org
If the guests canceles a DMA request we can prematurely
invoke all callbacks of buffered requests and flag all them
as orphaned. Ideally this avoids the need for draining all
requests. For CDROM devices this works in 100% of all cases.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1447345846-15624-5-git-send-email-pl@kamp.de
Signed-off-by: John Snow <jsnow@redhat.com>
Not that you can request a >2GiB transaction, but that's why checking
for it makes no sense anymore.
With the newer 'limit' parameter to prepare_buf, we no longer need a
static limit. The maximum limit is still 2GiB, but the limit parameter
is set to the current transaction size, which cannot surpass 32MiB
(512 * 65536). If the PRDT surpasses the transactional size, then,
we'll just carry out the normative underflow handling pathways instead
of needing an extra, strange pathway that worries about hitting some
logistical cap for the largest sglist we can support -- we'll never
even attempt to build one that big anymore.
Reported-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1445902682-20051-1-git-send-email-jsnow@redhat.com
prepare_buf should not always grab as many descriptors
as it can, sometimes it should self-limit.
For example, an NCQ transfer of 1 sector with a PRDT that
describes 4GiB of data should not copy 4GiB of data, it
should just transfer that first 512 bytes.
PIO is not affected, because the dma_buf_rw dma helpers
already have a byte limit built-in to them, but DMA/NCQ
will exhaust the entire list regardless of requested size.
AHCI 1.3 specifies in section 6.1.6 Command List Underflow that
NCQ is not required to detect underflow conditions. Non-NCQ
pathways signal underflow by writing to the PRDBC field, which
will already occur by writing the actual transferred byte count
to the PRDBC, signaling the underflow.
Our NCQ pathways aren't required to detect underflow, but since our DMA
backend uses the size of the PRDT to determine the size of the transer,
if our PRDT is bigger than the transaction (the underflow condition) it
doesn't cost us anything to detect it and truncate the PRDT.
This is a recoverable error and is not signaled to the guest, in either
NCQ or normal DMA cases.
For BMDMA, the existing pathways should see no guest-visible difference,
but any bytes described in the overage will no longer be transferred
before indicating to the guest that there was an underflow.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-2-git-send-email-jsnow@redhat.com
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
valgrind complains about:
==16447== 16 bytes in 2 blocks are definitely lost in loss record 1,304 of 3,310
==16447== at 0x4C2845D: malloc (in /usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==16447== by 0x2E4FD7: malloc_and_trace (vl.c:2546)
==16447== by 0x64C770E: g_malloc (in /usr/lib64/libglib-2.0.so.0.3600.3)
==16447== by 0x36FB47: qemu_extend_irqs (irq.c:55)
==16447== by 0x36FBD3: qemu_allocate_irqs (irq.c:64)
==16447== by 0x3B4B44: bmdma_init (pci.c:464)
==16447== by 0x3B547B: pci_piix_init_ports (piix.c:144)
==16447== by 0x3B55D2: pci_piix_ide_realize (piix.c:164)
==16447== by 0x3EAEC6: pci_qdev_realize (pci.c:1790)
==16447== by 0x36C685: device_set_realized (qdev.c:1058)
==16447== by 0x47179E: property_set_bool (object.c:1514)
==16447== by 0x470098: object_property_set (object.c:837)
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hlbC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block patches for 2.3
# gpg: Signature made Tue Mar 10 13:03:17 2015 GMT using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream: (73 commits)
MAINTAINERS: Add jcody as blockjobs, block devices maintainer
iotests: add O_DIRECT alignment probing test
block/raw-posix: fix launching with failed disks
MAINTAINERS: Add jsnow as IDE maintainer
sheepdog: Fix misleading error messages in sd_snapshot_create()
Add testcase for scsi-hd devices without drive property
scsi-hd: fix property unset case
block/vdi: Add locking for parallel requests
iotests: Drop vpc from 004's and 104's format list
iotests: Remove 006
iotests: Fix 051's reference output
virtio-blk: Remove the stale FIXME comment
tests: Check QVIRTIO_F_ANY_LAYOUT flag in virtio-blk test
libqos: Solve bug in interrupt checking when using MSIX in virtio-pci.c
sheepdog: fix confused return values
qtest/ahci: add fragmented dma test
qtest/ahci: Add PIO and LBA48 tests
qtest/ahci: Add DMA test variants
libqos/ahci: add ahci command helpers
qtest/ahci: Add a macro bootup routine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This moves more common restarting logic to the core IDE code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-10-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Start moving the initial state of the current request to IDEBus, so that
AHCI can use it. The set_unit callback is not used anymore once this is
done.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-9-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With BMDMA specific excised from the restart functions,
create a HBA-agnostic restart callback to be shared
between the different HBAs.
Change the callback registered with the vmstate_change
handler to always point to ide_restart_cb instead of
relying on the IDEDMAOps.restart_cb() member.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-7-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass the containing IDEBus to the restart_cb instead
of the more specific BMDMAState child.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-6-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Whenever an error stops the VM, ide_handle_rw_error does
"s->bus->dma->unit = s->unit". So we can just use
idebus_active_if.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-5-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the restart_dma callback and adjusts
the ide_restart_dma function to utilize this callback
to call the BMDMA-specific restart code instead of statically
executing BMDMA-specific code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch begins refactoring the restart dma functions
out of bmdma to be shared with AHCI and other future
IDE HBA implementations.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(With the previous atapi_dma flag recovery)
If migration happens between the ATAPI command being written and the
bmdma being started, the DMA is dropped. Eventually the guest times
out and recovers, but that can take many seconds.
(This is rare, on a pingpong reading the CD continuously I hit
this about ~1/30-1/50 migrates)
I don't think we've got enough state to be able to recover safely
at this point, so I throw a 'medium error, no seek complete'
that I'm assuming guests will try and recover from an apparently
dirty CD.
OK, it's a hack, the real solution is probably to push a lot of
ATAPI state into the migration stream, but this is a fix that
works with no stream changes. Tested only on Linux (both RHEL5
(pre-libata) and RHEL7).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This impacts both BMDMA and AHCI HBA interfaces for IDE.
Currently, we confuse the difference between a PRDT having
"0 bytes" and a PRDT having "0 complete sectors."
When we receive an incomplete sector, inconsistent error checking
leads to an infinite loop wherein the call succeeds, but it
didn't give us enough bytes -- leading us to re-call the
DMA chain over and over again. This leads to, in the BMDMA case,
leaked memory for short PRDTs, and infinite loops and resource
usage in the AHCI case.
The .prepare_buf() callback is reworked to return the number of
bytes that it successfully prepared. 0 is a valid, non-error
answer that means the table was empty and described no bytes.
-1 indicates an error.
Our current implementation uses the io_buffer in IDEState to
ultimately describe the size of a prepared scatter-gather list.
Even though the AHCI PRDT/SGList can be as large as 256GiB, the
AHCI command header limits transactions to just 4GiB. ATA8-ACS3,
however, defines the largest transaction to be an LBA48 command
that transfers 65,536 sectors. With a 512 byte sector size, this
is just 32MiB.
Since our current state structures use the int type to describe
the size of the buffer, and this state is migrated as int32, we
are limited to describing 2GiB buffer sizes unless we change the
migration protocol.
For this reason, this patch begins to unify the assertions in the
IDE pathways that the scatter-gather list provided by either the
AHCI PRDT or the PCI BMDMA PRDs can only describe, at a maximum,
2GiB. This should be resilient enough unless we need a sector
size that exceeds 32KiB.
Further, the likelihood of any guest operating system actually
attempting to transfer this much data in a single operation is
very slim.
To this end, the IDEState variables have been updated to more
explicitly clarify our maximum supported size. Callers to the
prepare_buf callback have been reworked to understand the new
return code, and all versions of the prepare_buf callback have
been adjusted accordingly.
Lastly, the ahci_populate_sglist helper, relied upon by the
AHCI implementation of .prepare_buf() as well as the PCI
implementation of the callback have had overflow assertions
added to help make clear the reasonings behind the various
type changes.
[Added %d -> %"PRId64" fix John sent because off_pos changed from int to
int64_t.
--Stefan]
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use it with block backends shortly, and the name is going to fit
badly there. It's a block layer thing anyway, not just a block driver
thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
