The check on x86ms->apic_id_limit in pc_machine_done() had two problems.
Firstly, we need KVM to support the X2APIC API in order to allow IRQ
delivery to APICs >= 255. So we need to call/check kvm_enable_x2apic(),
which was done elsewhere in *some* cases but not all.
Secondly, microvm needs the same check. So move it from pc_machine_done()
to x86_cpus_init() where it will work for both.
The check in kvm_cpu_instance_init() is now redundant and can be dropped.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20220314142544.150555-1-dwmw2@infradead.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If CPUID.(EAX=07H, ECX=0):EDX[19] is set to 1, the processor
supports Architectural LBRs. In this case, CPUID leaf 01CH
indicates details of the Architectural LBRs capabilities.
XSAVE support for Architectural LBRs is enumerated in
CPUID.(EAX=0DH, ECX=0FH).
Signed-off-by: Yang Weijiang <weijiang.yang@intel.com>
Message-Id: <20220215195258.29149-9-weijiang.yang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Arch LBR record MSRs and control MSRs will be migrated
to destination guest if the vcpus were running with Arch
LBR active.
Signed-off-by: Yang Weijiang <weijiang.yang@intel.com>
Message-Id: <20220215195258.29149-8-weijiang.yang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the first generation of Arch LBR, the max support
Arch LBR depth is 32, both host and guest use the value
to set depth MSR. This can simplify the implementation
of patch given the side-effect of mismatch of host/guest
depth MSR: XRSTORS will reset all recording MSRs to 0s
if the saved depth mismatches MSR_ARCH_LBR_DEPTH.
In most of the cases Arch LBR is not in active status,
so check the control bit before save/restore the big
chunck of Arch LBR MSRs.
Signed-off-by: Yang Weijiang <weijiang.yang@intel.com>
Message-Id: <20220215195258.29149-7-weijiang.yang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Define Arch LBR bit in XSS and save/restore structure
for XSAVE area size calculation.
Signed-off-by: Yang Weijiang <weijiang.yang@intel.com>
Message-Id: <20220215195258.29149-6-weijiang.yang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There're some new features, including Arch LBR, depending
on XSAVES/XRSTORS support, the new instructions will
save/restore data based on feature bits enabled in XCR0 | XSS.
This patch adds the basic support for related CPUID enumeration
and meanwhile changes the name from FEAT_XSAVE_COMP_{LO|HI} to
FEAT_XSAVE_XCR0_{LO|HI} to differentiate clearly the feature
bits in XCR0 and those in XSS.
Signed-off-by: Yang Weijiang <weijiang.yang@intel.com>
Message-Id: <20220215195258.29149-5-weijiang.yang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When try to get one msr from KVM, I found there's no such kind of
existing interface while kvm_put_one_msr() is there. So here comes
the patch. It'll remove redundant preparation code before finally
call KVM_GET_MSRS IOCTL.
No functional change intended.
Signed-off-by: Yang Weijiang <weijiang.yang@intel.com>
Message-Id: <20220215195258.29149-4-weijiang.yang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Last Branch Recording (LBR) is a performance monitor unit (PMU)
feature on Intel processors which records a running trace of the most
recent branches taken by the processor in the LBR stack. This option
indicates the LBR format to enable for guest perf.
The LBR feature is enabled if below conditions are met:
1) KVM is enabled and the PMU is enabled.
2) msr-based-feature IA32_PERF_CAPABILITIES is supporterd on KVM.
3) Supported returned value for lbr_fmt from above msr is non-zero.
4) Guest vcpu model does support FEAT_1_ECX.CPUID_EXT_PDCM.
5) User-provided lbr-fmt value doesn't violate its bitmask (0x3f).
6) Target guest LBR format matches that of host.
Co-developed-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Yang Weijiang <weijiang.yang@intel.com>
Message-Id: <20220215195258.29149-3-weijiang.yang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Icelake, is the codename for Intel 3rd generation Xeon Scalable server
processors. There isn't ever client variants. This "Icelake-Client" CPU
model was added wrongly and imaginarily.
It has been deprecated since v5.2, now it's time to remove it completely
from code.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1647247859-4947-1-git-send-email-robert.hu@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes the following error that would occur when trying to resume
a WHPX-accelerated VM from a breakpoint:
qemu: WHPX: Failed to set interrupt state registers, hr=c0350005
The error arises from an incorrect CR8 value being passed to
WHvSetVirtualProcessorRegisters() that doesn't match the
value set via WHvSetVirtualProcessorInterruptControllerState2().
Signed-off-by: Ivan Shcherbakov <ivan@sysprogs.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When cache_info_passthrough is requested, QEMU passes the host values
of the cache information CPUID leaves down to the guest. However,
it blindly assumes that the CPUID leaf exists on the host, and this
cannot be guaranteed: for example, KVM has recently started to
synthesize AMD leaves up to 0x80000021 in order to provide accurate
CPU bug information to guests.
Querying a nonexistent host leaf fills the output arguments of
host_cpuid with data that (albeit deterministic) is nonsensical
as cache information, namely the data in the highest Intel CPUID
leaf. If said highest leaf is not ECX-dependent, this can even
cause an infinite loop when kvm_arch_init_vcpu prepares the input
to KVM_SET_CPUID2. The infinite loop is only terminated by an
abort() when the array gets full.
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We commonly define the header guard symbol without an explicit value.
Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-4-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Change to generated file ebpf/rss.bpf.skeleton.h backed out]
Capstone should be superior to the old libopcode disassembler,
so we can drop the old file nowadays.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220412165836.355850-4-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Support for xcr0 to be able to enable xsave/xrstor. This by itself
is not sufficient to enable xsave/xrstor. WHPX XSAVE API's also
needs to be hooked up.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Message-Id: <MW2PR2101MB1116F07C07A26FD7A7ED8DCFC0780@MW2PR2101MB1116.namprd21.prod.outlook.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The abs1 function in ops_sse.h only works sorrectly when the result fits
in a signed int. This is fine most of the time because we're only dealing
with byte sized values.
However pcmp_elen helper function uses abs1 to calculate the absolute value
of a cpu register. This incorrectly truncates to 32 bits, and will give
the wrong anser for the most negative value.
Fix by open coding the saturation check before taking the absolute value.
Signed-off-by: Paul Brook <paul@nowt.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Coverity warns that 14 << data32 may overflow with respect
to the target_ulong to which it is subsequently added.
We know this wasn't true because data32 is in [1,2],
but the suggested fix is perfectly fine.
Fixes: Coverity CID 1487135, 1487256
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-Id: <20220401184635.327423-1-richard.henderson@linaro.org>
G_NORETURN was introduced in glib 2.68, fallback to G_GNUC_NORETURN in
glib-compat.
Note that this attribute must be placed before the function declaration
(bringing a bit of consistency in qemu codebase usage).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Message-Id: <20220420132624.2439741-20-marcandre.lureau@redhat.com>
Use the FILE* from qemu_log_trylock more often.
Support per-thread log files with -d tid.
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmJgStUdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV+c9Af/ZXnKe6bz5yjXy1mS
mNIBJUPKrz1RXFfJxuCfEDWrtNc/gvQyvc3weZG5X0cXpiczeWA5V/9xbE9hu5gV
4rePiIHWmOrais6GZlqEu2F8P3/XyqdPHtcdBfa1hDneixtpqMHCqnh36nQjHyiU
ogFxEJ/M9tTwhuWZrXe/JSYAiALEDYMK9bk4RUMOP1c4v37rXqUNOAM1IPhfxLL/
bK9DQMpz5oUNsWWaqBQ2wQWHkNTOpUEkKGQv0xcQF5SdpYwaxakW9B7/h4QSeOUn
oY6MFTmkJ4BPrLnkcubn+3PICc9LW0OFuzNnUdMCbeqVbjAUQrdMDalKpy4uNFv9
U1VqHg==
=Mt5s
-----END PGP SIGNATURE-----
Merge tag 'pull-log-20220420' of https://gitlab.com/rth7680/qemu into staging
Clean up log locking.
Use the FILE* from qemu_log_trylock more often.
Support per-thread log files with -d tid.
# -----BEGIN PGP SIGNATURE-----
#
# iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmJgStUdHHJpY2hhcmQu
# aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV+c9Af/ZXnKe6bz5yjXy1mS
# mNIBJUPKrz1RXFfJxuCfEDWrtNc/gvQyvc3weZG5X0cXpiczeWA5V/9xbE9hu5gV
# 4rePiIHWmOrais6GZlqEu2F8P3/XyqdPHtcdBfa1hDneixtpqMHCqnh36nQjHyiU
# ogFxEJ/M9tTwhuWZrXe/JSYAiALEDYMK9bk4RUMOP1c4v37rXqUNOAM1IPhfxLL/
# bK9DQMpz5oUNsWWaqBQ2wQWHkNTOpUEkKGQv0xcQF5SdpYwaxakW9B7/h4QSeOUn
# oY6MFTmkJ4BPrLnkcubn+3PICc9LW0OFuzNnUdMCbeqVbjAUQrdMDalKpy4uNFv9
# U1VqHg==
# =Mt5s
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 20 Apr 2022 11:03:01 AM PDT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [ultimate]
* tag 'pull-log-20220420' of https://gitlab.com/rth7680/qemu: (39 commits)
util/log: Support per-thread log files
util/log: Limit RCUCloseFILE to file closing
util/log: Rename QemuLogFile to RCUCloseFILE
util/log: Combine two logfile closes
util/log: Hoist the eval of is_daemonized in qemu_set_log_internal
util/log: Rename qemu_logfile_mutex to global_mutex
util/log: Rename qemu_logfile to global_file
util/log: Rename logfilename to global_filename
util/log: Remove qemu_log_close
softmmu: Use qemu_set_log_filename_flags
linux-user: Use qemu_set_log_filename_flags
bsd-user: Use qemu_set_log_filename_flags
util/log: Introduce qemu_set_log_filename_flags
sysemu/os-win32: Test for and use _lock_file/_unlock_file
include/qemu/log: Move entire implementation out-of-line
include/exec/log: Do not reference QemuLogFile directly
tests/unit: Do not reference QemuLogFile directly
linux-user: Expand log_page_dump inline
bsd-user: Expand log_page_dump inline
util/log: Drop call to setvbuf
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We have fetched and locked the logfile in translator_loop.
Pass the filepointer down to the disas_log hook so that it
need not be fetched and locked again.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-13-richard.henderson@linaro.org>
Inside qemu_log, we perform qemu_log_trylock/unlock, which need
not be done if we have already performed the lock beforehand.
Always check the result of qemu_log_trylock -- only checking
qemu_loglevel_mask races with the acquisition of the lock on
the logfile.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-10-richard.henderson@linaro.org>
This function can fail, which makes it more like ftrylockfile
or pthread_mutex_trylock than flockfile or pthread_mutex_lock,
so rename it.
To closer match the other trylock functions, release rcu_read_lock
along the failure path, so that qemu_log_unlock need not be called
on failure.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-8-richard.henderson@linaro.org>
During the conversion to the gdb_get_reg128 helpers the high and low
parts of the XMM register where inadvertently swapped. This causes
reads of the register to report the incorrect value to gdb.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/971
Fixes: b7b8756a9c (target/i386: use gdb_get_reg helpers)
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: qemu-stable@nongnu.org
Message-Id: <20220419091020.3008144-25-alex.bennee@linaro.org>
In commit b7711471f5 in 2014 we refactored the handling of the x86
vector registers so that instead of separate structs XMMReg, YMMReg
and ZMMReg for representing the 16-byte, 32-byte and 64-byte width
vector registers and multiple fields in the CPU state, we have a
single type (XMMReg, later renamed to ZMMReg) and a single struct
field (xmm_regs). However, in 2017 in commit c97d6d2cdf some of
the old struct types and CPU state fields got added back, when we
merged in the hvf support (which had developed in a separate fork
that had presumably not had the refactoring of b7711471f5), as part
of code handling xsave. Commit f585195ec0 then almost immediately
dropped that xsave code again in favour of sharing the xsave handling
with KVM, but forgot to remove the now unused CPU state fields and
struct types.
Delete the unused types and CPUState fields.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220412110047.1497190-1-peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The i386 target consolidates all vector registers so that instead of
XMMReg, YMMReg and ZMMReg structs there is a single ZMMReg that can
fit all of SSE, AVX and AVX512.
When TCG copies data from and to the SSE registers, it uses the
full 64-byte width. This is not a correctness issue because TCG
never lets guest code see beyond the first 128 bits of the ZMM
registers, however it causes uninitialized stack memory to
make it to the CPU's migration stream.
Fix it by only copying the low 16 bytes of the ZMMReg union into
the destination register.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jon Doron <arilou@gmail.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220216102500.692781-5-arilou@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SynDbg commands can come from two different flows:
1. Hypercalls, in this mode the data being sent is fully
encapsulated network packets.
2. SynDbg specific MSRs, in this mode only the data that needs to be
transfered is passed.
Signed-off-by: Jon Doron <arilou@gmail.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220216102500.692781-4-arilou@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add all required definitions for hyperv synthetic debugger interface.
Signed-off-by: Jon Doron <arilou@gmail.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220216102500.692781-3-arilou@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Below is the updated version of the patch adding debugging support to WHPX.
It incorporates feedback from Alex Bennée and Peter Maydell regarding not
changing the emulation logic depending on the gdb connection status.
Instead of checking for an active gdb connection to determine whether QEMU
should intercept the INT1 exceptions, it now checks whether any breakpoints
have been set, or whether gdb has explicitly requested one or more CPUs to
do single-stepping. Having none of these condition present now has the same
effect as not using gdb at all.
Message-Id: <0e7f01d82e9e$00e9c360$02bd4a20$@sysprogs.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The types are no longer used in bswap.h since commit
f930224fff ("bswap.h: Remove unused float-access functions"), there
isn't much sense in keeping it there and having a dependency on fpu/.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220323155743.1585078-29-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the global variables with inlined helper functions. getpagesize() is very
likely annotated with a "const" function attribute (at least with glibc), and thus
optimization should apply even better.
This avoids the need for a constructor initialization too.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220323155743.1585078-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace a config-time define with a compile time condition
define (compatible with clang and gcc) that must be declared prior to
its usage. This avoids having a global configure time define, but also
prevents from bad usage, if the config header wasn't included before.
This can help to make some code independent from qemu too.
gcc supports __BYTE_ORDER__ from about 4.6 and clang from 3.2.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[ For the s390x parts I'm involved in ]
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new field 'cpu0-id' to the response of query-sev-capabilities QMP
command. The value of the field is the base64-encoded unique ID of CPU0
(socket 0), which can be used to retrieve the signed CEK of the CPU from
AMD's Key Distribution Service (KDS).
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220228093014.882288-1-dovmurik@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some versions of Windows hang on reboot if their TSC value is greater
than 2^54. The calibration of the Hyper-V reference time overflows
and fails; as a result the processors' clock sources are out of sync.
The issue is that the TSC _should_ be reset to 0 on CPU reset and
QEMU tries to do that. However, KVM special cases writing 0 to the
TSC and thinks that QEMU is trying to hot-plug a CPU, which is
correct the first time through but not later. Thwart this valiant
effort and reset the TSC to 1 instead, but only if the CPU has been
run once.
For this to work, env->tsc has to be moved to the part of CPUArchState
that is not zeroed at the beginning of x86_cpu_reset.
Reported-by: Vadim Rozenfeld <vrozenfe@redhat.com>
Supersedes: <20220324082346.72180-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
High bits in the immediate operand of SSE comparisons are ignored, they
do not result in an undefined opcode exception. This is mentioned
explicitly in the Intel documentation.
Reported-by: sonicadvance1@gmail.com
Closes: https://gitlab.com/qemu-project/qemu/-/issues/184
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some AMD processors expose the PKRU extended save state even if they do not have
the related PKU feature in CPUID. Worse, when they do they report a size of
64, whereas the expected size of the PKRU extended save state is 8, therefore
the esa->size == eax assertion does not hold.
The state is already ignored by KVM_GET_SUPPORTED_CPUID because it
was not enabled in the host XCR0. However, QEMU kvm_cpu_xsave_init()
runs before QEMU invokes arch_prctl() to enable dynamically-enabled
save states such as XTILEDATA, and KVM_GET_SUPPORTED_CPUID hides save
states that have yet to be enabled. Therefore, kvm_cpu_xsave_init()
needs to consult the host CPUID instead of KVM_GET_SUPPORTED_CPUID,
and dies with an assertion failure.
When setting up the ExtSaveArea array to match the host, ignore features that
KVM does not report as supported. This will cause QEMU to skip the incorrect
CPUID leaf instead of tripping the assertion.
Closes: https://gitlab.com/qemu-project/qemu/-/issues/916
Reported-by: Daniel P. Berrangé <berrange@redhat.com>
Analyzed-by: Yang Zhong <yang.zhong@intel.com>
Reported-by: Peter Krempa <pkrempa@redhat.com>
Tested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the physical machine environment, when a SRAR error occurs,
the IA32_MCG_STATUS RIPV bit is set, but qemu does not set this
bit. When qemu injects an SRAR error into virtual machine, the
virtual machine kernel just call do_machine_check() to kill the
current task, but not call memory_failure() to isolate the faulty
page, which will cause the faulty page to be allocated and used
repeatedly. If used by the virtual machine kernel, it will cause
the virtual machine to crash
Signed-off-by: luofei <luofei@unicloud.com>
Message-Id: <20220120084634.131450-1-luofei@unicloud.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix vCPU hot-unplug related leak reported by Valgrind:
==132362== 4,096 bytes in 1 blocks are definitely lost in loss record 8,440 of 8,549
==132362== at 0x4C3B15F: memalign (vg_replace_malloc.c:1265)
==132362== by 0x4C3B288: posix_memalign (vg_replace_malloc.c:1429)
==132362== by 0xB41195: qemu_try_memalign (memalign.c:53)
==132362== by 0xB41204: qemu_memalign (memalign.c:73)
==132362== by 0x7131CB: kvm_init_xsave (kvm.c:1601)
==132362== by 0x7148ED: kvm_arch_init_vcpu (kvm.c:2031)
==132362== by 0x91D224: kvm_init_vcpu (kvm-all.c:516)
==132362== by 0x9242C9: kvm_vcpu_thread_fn (kvm-accel-ops.c:40)
==132362== by 0xB2EB26: qemu_thread_start (qemu-thread-posix.c:556)
==132362== by 0x7EB2159: start_thread (in /usr/lib64/libpthread-2.28.so)
==132362== by 0x9D45DD2: clone (in /usr/lib64/libc-2.28.so)
Reported-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Mark Kanda <mark.kanda@oracle.com>
Message-Id: <20220322120522.26200-1-philippe.mathieu.daude@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The instruction description says "It is loaded without rounding
errors." which implies we should have the widest rounding mode
possible.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/888
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220315121251.2280317-4-alex.bennee@linaro.org>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Patch created mechanically with:
$ spatch --in-place --sp-file scripts/coccinelle/use-g_new-etc.cocci \
--macro-file scripts/cocci-macro-file.h FILES...
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220315144156.1595462-4-armbru@redhat.com>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
KVM support for AMX includes a new system attribute, KVM_X86_XCOMP_GUEST_SUPP.
Commit 19db68ca68 ("x86: Grant AMX permission for guest", 2022-03-15) however
did not fully consider the behavior on older kernels. First, it warns
too aggressively. Second, it invokes the KVM_GET_DEVICE_ATTR ioctl
unconditionally and then uses the "bitmask" variable, which remains
uninitialized if the ioctl fails. Third, kvm_ioctl returns -errno rather
than -1 on errors.
While at it, explain why the ioctl is needed and KVM_GET_SUPPORTED_CPUID
is not enough.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Remove various build warnings
- Fix building with modules on macOS
- Fix mouse/keyboard GUI interactions
-----BEGIN PGP SIGNATURE-----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=PLdU
-----END PGP SIGNATURE-----
Merge tag 'darwin-20220315' of https://github.com/philmd/qemu into staging
Darwin-based host patches
- Remove various build warnings
- Fix building with modules on macOS
- Fix mouse/keyboard GUI interactions
# gpg: Signature made Tue 15 Mar 2022 12:52:19 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* tag 'darwin-20220315' of https://github.com/philmd/qemu: (21 commits)
MAINTAINERS: Volunteer to maintain Darwin-based hosts support
ui/cocoa: add option to swap Option and Command
ui/cocoa: capture all keys and combos when mouse is grabbed
ui/cocoa: release mouse when user switches away from QEMU window
ui/cocoa: add option to disable left-command forwarding to guest
ui/cocoa: Constify qkeycode translation arrays
configure: Pass filtered QEMU_OBJCFLAGS to meson
meson: Log QEMU_CXXFLAGS content in summary
meson: Resolve the entitlement.sh script once for good
osdep: Avoid using Clang-specific __builtin_available()
audio: Rename coreaudio extension to use Objective-C compiler
coreaudio: Always return 0 in handle_voice_change
audio: Log context for audio bug
audio/dbus: Fix building with modules on macOS
audio/coreaudio: Remove a deprecation warning on macOS 12
block/file-posix: Remove a deprecation warning on macOS 12
hvf: Remove deprecated hv_vcpu_flush() calls
hvf: Make hvf_get_segments() / hvf_put_segments() local
hvf: Use standard CR0 and CR4 register definitions
tests/fp/berkeley-testfloat-3: Ignore ignored #pragma directives
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When building on macOS 11 [*], we get:
In file included from ../target/i386/hvf/hvf.c:59:
../target/i386/hvf/vmx.h:174:5: error: 'hv_vcpu_flush' is deprecated: first deprecated in macOS 11.0 - This API has no effect and always returns HV_UNSUPPORTED [-Werror,-Wdeprecated-declarations]
hv_vcpu_flush(vcpu);
^
/Library/Developer/CommandLineTools/SDKs/MacOSX.sdk/System/Library/Frameworks/Hypervisor.framework/Headers/hv.h:364:20: note: 'hv_vcpu_flush' has been explicitly marked deprecated here
extern hv_return_t hv_vcpu_flush(hv_vcpuid_t vcpu)
^
Since this call "has no effect", simply remove it ¯\_(ツ)_/¯
Not very useful deprecation doc:
https://developer.apple.com/documentation/hypervisor/1441386-hv_vcpu_flush
[*] Also 10.15 (Catalina):
https://lore.kernel.org/qemu-devel/Yd3DmSqZ1SiJwd7P@roolebo.dev/
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Tested-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Both hvf_get_segments/hvf_put_segments() functions are only
used within x86hvf.c: do not declare them as public API.
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Tested-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
No need to have our own definitions of these registers.
Signed-off-by: Cameron Esfahani <dirty@apple.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Even when the feature is not supported in guest CPUID,
still set the msr to the default value which will
be the only value KVM will accept in this case
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220223115824.319821-1-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Windows 11 with WSL2 enabled (Hyper-V) fails to boot with Icelake-Server
{-v5} CPU model but boots well with '-cpu host'. Apparently, it expects
5-level paging and 5-level EPT support to come in pair but QEMU's
Icelake-Server CPU model lacks the later. Introduce 'Icelake-Server-v6'
CPU model with 'vmx-page-walk-5' enabled by default.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220221145316.576138-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
XFD(eXtended Feature Disable) allows to enable a
feature on xsave state while preventing specific
user threads from using the feature.
Support save and restore XFD MSRs if CPUID.D.1.EAX[4]
enumerate to be valid. Likewise migrate the MSRs and
related xsave state necessarily.
Signed-off-by: Zeng Guang <guang.zeng@intel.com>
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20220217060434.52460-8-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When dynamic xfeatures (e.g. AMX) are used by the guest, the xsave
area would be larger than 4KB. KVM_GET_XSAVE2 and KVM_SET_XSAVE
under KVM_CAP_XSAVE2 works with a xsave buffer larger than 4KB.
Always use the new ioctls under KVM_CAP_XSAVE2 when KVM supports it.
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Signed-off-by: Zeng Guang <guang.zeng@intel.com>
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20220217060434.52460-7-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add AMX primary feature bits XFD and AMX_TILE to
enumerate the CPU's AMX capability. Meanwhile, add
AMX TILE and TMUL CPUID leaf and subleaves which
exist when AMX TILE is present to provide the maximum
capability of TILE and TMUL.
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20220217060434.52460-6-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel introduces XFD faulting mechanism for extended
XSAVE features to dynamically enable the features in
runtime. If CPUID (EAX=0Dh, ECX=n, n>1).ECX[2] is set
as 1, it indicates support for XFD faulting of this
state component.
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20220217060434.52460-5-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Kernel allocates 4K xstate buffer by default. For XSAVE features
which require large state component (e.g. AMX), Linux kernel
dynamically expands the xstate buffer only after the process has
acquired the necessary permissions. Those are called dynamically-
enabled XSAVE features (or dynamic xfeatures).
There are separate permissions for native tasks and guests.
Qemu should request the guest permissions for dynamic xfeatures
which will be exposed to the guest. This only needs to be done
once before the first vcpu is created.
KVM implemented one new ARCH_GET_XCOMP_SUPP system attribute API to
get host side supported_xcr0 and Qemu can decide if it can request
dynamically enabled XSAVE features permission.
https://lore.kernel.org/all/20220126152210.3044876-1-pbonzini@redhat.com/
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Message-Id: <20220217060434.52460-4-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The AMX TILECFG register and the TMMx tile data registers are
saved/restored via XSAVE, respectively in state component 17
(64 bytes) and state component 18 (8192 bytes).
Add AMX feature bits to x86_ext_save_areas array to set
up AMX components. Add structs that define the layout of
AMX XSAVE areas and use QEMU_BUILD_BUG_ON to validate the
structs sizes.
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20220217060434.52460-3-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The extended state subleaves (EAX=0Dh, ECX=n, n>1).ECX[1]
indicate whether the extended state component locates
on the next 64-byte boundary following the preceding state
component when the compacted format of an XSAVE area is
used.
Right now, they are all zero because no supported component
needed the bit to be set, but the upcoming AMX feature will
use it. Fix the subleaves value according to KVM's supported
cpuid.
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20220217060434.52460-2-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Loading a non-canonical address into rsp when handling an interrupt or
performing a far call should raise a #SS not a #GP.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/870
Signed-off-by: Gareth Webb <gareth.webb@umbralsoftware.co.uk>
Message-Id: <164529651121.25406.15337137068584246397-0@git.sr.ht>
[Move get_pg_mode to seg_helper.c for user-mode emulators. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
LA57/PKE/PKS is only relevant in 64-bit mode, and NXE is only relevant if
PAE is in use. Since there is code that checks PG_MODE_LA57 to determine
the canonicality of addresses, make sure that the bit is not set by
mistake in 32-bit mode. While it would not be a problem because 32-bit
addresses by definition fit in both 48-bit and 57-bit address spaces,
it is nicer if get_pg_mode() actually returns whether a feature is enabled,
and it allows a few simplifications in the page table walker.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We invoke the kvm_irqchip_commit_routes() for each addition to MSI route
table, which is not efficient if we are adding lots of routes in some cases.
This patch lets callers invoke the kvm_irqchip_commit_routes(), so the
callers can decide how to optimize.
[1] https://lists.gnu.org/archive/html/qemu-devel/2021-11/msg00967.html
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20220222141116.2091-3-longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes the following error triggered when stopping and resuming a 64-bit
Linux kernel via gdb:
qemu-system-x86_64.exe: WHPX: Failed to set virtual processor context, hr=c0350005
The previous logic for synchronizing the values did not take into account
that the lower 4 bits of the CR8 register, containing the priority level,
mapped to bits 7:4 of the APIC.TPR register (see section 10.8.6.1 of
Volume 3 of Intel 64 and IA-32 Architectures Software Developer's Manual).
The caused WHvSetVirtualProcessorRegisters() to fail with an error,
effectively preventing GDB from changing the guest context.
Signed-off-by: Ivan Shcherbakov <ivan@sysprogs.com>
Message-Id: <010b01d82874$bb4ef160$31ecd420$@sysprogs.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make sure that pausing the VM while in 64-bit mode will set the
HF_CS64_MASK flag in env->hflags (see x86_update_hflags() in
target/i386/cpu.c).
Without it, the code in gdbstub.c would only use the 32-bit register values
when debugging 64-bit targets, making debugging effectively impossible.
Signed-off-by: Ivan Shcherbakov <ivan@sysprogs.com>
Message-Id: <00f701d82874$68b02000$3a106000$@sysprogs.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* cleanups of qemu_oom_check() and qemu_memalign()
* target/arm/translate-neon: UNDEF if VLD1/VST1 stride bits are non-zero
* target/arm/translate-neon: Simplify align field check for VLD3
* GICv3 ITS: add more trace events
* GICv3 ITS: implement 8-byte accesses properly
* GICv3: fix minor issues with some trace/log messages
* ui/cocoa: Use the standard about panel
* target/arm: Provide cpu property for controling FEAT_LPA2
* hw/arm/virt: Disable LPA2 for -machine virt-6.2
-----BEGIN PGP SIGNATURE-----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=ix0J
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20220307' into staging
target-arm queue:
* cleanups of qemu_oom_check() and qemu_memalign()
* target/arm/translate-neon: UNDEF if VLD1/VST1 stride bits are non-zero
* target/arm/translate-neon: Simplify align field check for VLD3
* GICv3 ITS: add more trace events
* GICv3 ITS: implement 8-byte accesses properly
* GICv3: fix minor issues with some trace/log messages
* ui/cocoa: Use the standard about panel
* target/arm: Provide cpu property for controling FEAT_LPA2
* hw/arm/virt: Disable LPA2 for -machine virt-6.2
# gpg: Signature made Mon 07 Mar 2022 16:46:06 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20220307:
hw/arm/virt: Disable LPA2 for -machine virt-6.2
target/arm: Provide cpu property for controling FEAT_LPA2
ui/cocoa: Use the standard about panel
hw/intc/arm_gicv3_cpuif: Fix register names in ICV_HPPIR read trace event
hw/intc/arm_gicv3: Fix missing spaces in error log messages
hw/intc/arm_gicv3: Specify valid and impl in MemoryRegionOps
hw/intc/arm_gicv3_its: Add trace events for table reads and writes
hw/intc/arm_gicv3_its: Add trace events for commands
target/arm/translate-neon: Simplify align field check for VLD3
target/arm/translate-neon: UNDEF if VLD1/VST1 stride bits are non-zero
osdep: Move memalign-related functions to their own header
util: Put qemu_vfree() in memalign.c
util: Use meson checks for valloc() and memalign() presence
util: Share qemu_try_memalign() implementation between POSIX and Windows
meson.build: Don't misdetect posix_memalign() on Windows
util: Return valid allocation for qemu_try_memalign() with zero size
util: Unify implementations of qemu_memalign()
util: Make qemu_oom_check() a static function
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the various memalign-related functions out of osdep.h and into
their own header, which we include only where they are used.
While we're doing this, add some brief documentation comments.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220226180723.1706285-10-peter.maydell@linaro.org
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220305233415.64627-3-philippe.mathieu.daude@gmail.com>
ArchCPU is our interface with target-specific code. Use it as
a forward-declared opaque pointer (abstract type), having its
structure defined by each target.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-15-f4bug@amsat.org>
Replace the boilerplate code to declare CPU QOM types
and macros, and forward-declare the CPU instance type.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-14-f4bug@amsat.org>
While CPUState is our interface with generic code, CPUArchState is
our interface with target-specific code. Use CPUArchState as an
abstract type, defined by each target.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-13-f4bug@amsat.org>
excp_helper.c requires "exec/exec-all.h" for tlb_set_page_with_attrs()
and misc_helper.c for tlb_flush().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-8-f4bug@amsat.org>
Add cpu_thread_is_idle() to AccelOps, and implement it for the
KVM / WHPX accelerators.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-11-f4bug@amsat.org>
Mirror "sysemu/kvm.h" #ifdef'ry to define CONFIG_HAX_IS_POSSIBLE,
expose hax_allowed to hax_enabled() macro.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-9-f4bug@amsat.org>
The dh_alias redirect is intended to handle TCG types as distinguished
from C types. TCG does not distinguish signed int from unsigned int,
because they are the same size. However, we need to retain this
distinction for dh_typecode, lest we fail to extend abi types properly
for the host call parameters.
This bug was detected when running the 'arm' emulator on an s390
system. The s390 uses TCG_TARGET_EXTEND_ARGS which triggers code
in tcg_gen_callN to extend 32 bit values to 64 bits; the incorrect
sign data in the typemask for each argument caused the values to be
extended as unsigned values.
This simple program exhibits the problem:
static volatile int num = -9;
static volatile int den = -5;
int main(void)
{
int quo = num / den;
printf("num %d den %d quo %d\n", num, den, quo);
exit(0);
}
When run on the broken qemu, this results in:
num -9 den -5 quo 0
The correct result is:
num -9 den -5 quo 1
Fixes: 7319d83a73 ("tcg: Combine dh_is_64bit and dh_is_signed to dh_typecode")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/876
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reported-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Tested-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* Some small fixes for the qtests
* Misc header cleanups by Philippe
-----BEGIN PGP SIGNATURE-----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=/azS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2022-02-21' into staging
* Improve virtio-net failover test
* Some small fixes for the qtests
* Misc header cleanups by Philippe
# gpg: Signature made Mon 21 Feb 2022 11:40:37 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/thuth-gitlab/tags/pull-request-2022-02-21: (25 commits)
hw/tricore: Remove unused and incorrect header
hw/m68k/mcf: Add missing 'exec/hwaddr.h' header
exec/exec-all: Move 'qemu/log.h' include in units requiring it
softmmu/runstate: Clean headers
linux-user: Add missing "qemu/timer.h" include
target: Add missing "qemu/timer.h" include
core/ptimers: Remove unnecessary 'sysemu/cpus.h' include
exec/ramblock: Add missing includes
qtest: Add missing 'hw/qdev-core.h' include
hw/acpi/memory_hotplug: Remove unused 'hw/acpi/pc-hotplug.h' header
hw/remote: Add missing include
hw/tpm: Clean includes
scripts: Remove the old switch-timer-api script
tests/qtest: failover: migration abort test with failover off
tests/qtest: failover: test migration if the guest doesn't support failover
tests/qtest: failover: check migration with failover off
tests/qtest: failover: check missing guest feature
tests/qtest: failover: check the feature is correctly provided
tests/qtest: failover: use a macro for check_one_card()
tests/qtest: failover: clean up pathname of tests
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "hardware version" machinery (qemu_set_hw_version(),
qemu_hw_version(), and the QEMU_HW_VERSION define) is used by fewer
than 10 files. Move it out from osdep.h into a new
qemu/hw-version.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-6-peter.maydell@linaro.org
Many files use "qemu/log.h" declarations but neglect to include
it (they inherit it via "exec/exec-all.h"). "exec/exec-all.h" is
a core component and shouldn't be used that way. Move the
"qemu/log.h" inclusion locally to each unit requiring it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220207082756.82600-10-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
I think these have been wrong since f193c7979c (do not depend on
thunk.h - more log items). Fix them so as not to confuse other
debugging.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220204204335.1689602-26-alex.bennee@linaro.org>
This is unnecessary, because the interrupt would be retrieved and queued
anyway by KVM_GET_VCPU_EVENTS and KVM_SET_VCPU_EVENTS respectively,
and it makes the flow more similar to the one for KVM_GET/SET_SREGS2.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to make PDPTRs part of the migration
stream and thus not reload them after migration which
is against X86 spec.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20211101132300.192584-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Renaming defines for quad in their various forms so that their signedness is
now explicit.
Done using git grep as suggested by Philippe, with a bit of hand edition to
keep assignments aligned.
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220106210108.138226-2-frederic.petrot@univ-grenoble-alpes.fr
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
QEMU coding style mandates to not use Linux kernel internal
types for scalars types. Replace __u32 by uint32_t.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211116193955.2793171-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In the SSE decode function gen_sse(), we combine a byte
'b' and a value 'b1' which can be [0..3], and switch on them:
b |= (b1 << 8);
switch (b) {
...
default:
unknown_op:
gen_unknown_opcode(env, s);
return;
}
In three cases inside this switch, we were then also checking for
"if (b1 >= 2) { goto unknown_op; }".
However, this can never happen, because the 'case' values in each place
are 0x0nn or 0x1nn and the switch will have directed the b1 == (2, 3)
cases to the default already.
This check was added in commit c045af25a5 in 2010; the added code
was unnecessary then as well, and was apparently intended only to
ensure that we never accidentally ended up indexing off the end
of an sse_op_table with only 2 entries as a result of future bugs
in the decode logic.
Change the checks to assert() instead, and make sure they're always
immediately before the array access they are protecting.
Fixes: Coverity CID 1460207
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmGXb2kUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNkQggArLP8V1vL9XW9LJ6v4UdO4dp78MRb
mP5zZhzY6CZ9NnbLW3rtS8GLrQ7XJdHl4huVIckIF3HW+TOBas2gXOiyWdskZRFS
UGSoeejj2RHmTzBKWZN77G/GB0ElyKt3wvXeCEx0F8yiJXZhkw6n6tp3U/lGnic3
sJmniTBZ+m3GGtrAaEL11x8ITdtdGEE4uIhspqN8X0kU+WkSsklm8+GAORzMpWGq
Fqo46dd1C+st1GvbDOnghltYOEPPyKE6pZYOnZwB8X8hi01Ex53wXBXl98G8r8rt
qA6P0lc5Eh8E3M7xm+kJBw1XNSkxjQioJ1SElmQFW5w5rVtYVSDEsaL4MQ==
=3kjz
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
Bugfixes for 6.2.
# gpg: Signature made Fri 19 Nov 2021 10:33:29 AM CET
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu:
chardev/wctable: don't free the instance in wctablet_chr_finalize
meson.build: Support ncurses on MacOS and OpenBSD
docs: Spell QEMU all caps
qtest/am53c974-test: add test for reset before transfer
esp: ensure that async_len is reset to 0 during esp_hard_reset()
nvmm: Fix support for stable version
meson: fix botched compile check conversions
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
NVMM user version 1 is the version being shipped with netbsd-9,
which is the most recent stable branch of NetBSD. This makes it
possible to use the NVMM accelerator on the most recent NetBSD
release, 9.2, which lacks nvmm_cpu_stop.
(CC'ing maintainers)
Signed-off-by: Nia Alarie <nia@NetBSD.org>
Reviewed-by: Kamil Rytarowski <kamil@netbsd.org>
Message-Id: <YWblCe2J8GwCaV9U@homeworld.netbsd.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use address_space_map/unmap and check for errors.
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
[Two lines wrapped for length - Daniel]
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
In sev_add_kernel_loader_hashes, the sizes of structs are known at
compile-time, so calculate needed padding at compile-time.
No functional change intended.
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Commit cff03145ed ("sev/i386: Introduce sev_add_kernel_loader_hashes
for measured linux boot", 2021-09-30) introduced measured direct boot
with -kernel, using an OVMF-designated hashes table which QEMU fills.
However, no checks are performed on the validity of the hashes area
designated by OVMF. Specifically, if OVMF publishes the
SEV_HASH_TABLE_RV_GUID entry but it is filled with zeroes, this will
cause QEMU to write the hashes entries over the first page of the
guest's memory (GPA 0).
Add validity checks to the published area. If the hashes table area's
base address is zero, or its size is too small to fit the aligned hashes
table, display an error and stop the guest launch. In such case, the
following error will be displayed:
qemu-system-x86_64: SEV: guest firmware hashes table area is invalid (base=0x0 size=0x0)
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Reported-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Commit cff03145ed ("sev/i386: Introduce sev_add_kernel_loader_hashes
for measured linux boot", 2021-09-30) introduced measured direct boot
with -kernel, using an OVMF-designated hashes table which QEMU fills.
However, if OVMF doesn't designate such an area, QEMU would completely
abort the VM launch. This breaks launching with -kernel using older
OVMF images which don't publish the SEV_HASH_TABLE_RV_GUID.
Fix that so QEMU will only look for the hashes table if the sev-guest
kernel-hashes option is set to on. Otherwise, QEMU won't look for the
designated area in OVMF and won't fill that area.
To enable addition of kernel hashes, launch the guest with:
-object sev-guest,...,kernel-hashes=on
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Reported-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Introduce new boolean 'kernel-hashes' option on the sev-guest object.
It will be used to to decide whether to add the hashes of
kernel/initrd/cmdline to SEV guest memory when booting with -kernel.
The default value is 'off'.
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
mmu_translate is supposed to return an error code for page faults; it is
not able to handle other exceptions. The #GP case for noncanonical
virtual addresses is not handled correctly, and incorrectly raised as
a page fault with error code 1. Since it cannot happen for nested
page tables, move it directly to handle_mmu_fault, even before the
invocation of mmu_translate.
Fixes: #676
Fixes: 661ff4879e ("target/i386: extract mmu_translate", 2021-05-11)
Cc: qemu-stable@nongnu.org
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Correctly look up the paging mode of the hypervisor when it is using 64-bit
mode but the guest is not.
Fixes: 68746930ae ("target/i386: use mmu_translate for NPT walk", 2021-05-11)
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* DMA support in the multiboot option ROM
* Rename default-bus-bypass-iommu
* Deprecate -watchdog and cleanup -watchdog-action
* HVF fix for <PAGE_SIZE regions
* Support TSC scaling for AMD nested virtualization
* Fix for ESP fuzzing bug
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmGBUeEUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOh+Qf+OMRhRiv6dYjbK/5zXrx81AgxYAY3
dBUSr8v16LyrMl1U3DZWzhD+MzQsC83m/Xsh4lGxlHDWtkK9QQA5xDG95JZdY26i
MGCbbjnFHISbyBQV9Y724gPfPjOOODuoFbzafSx6VLITOcyv1ye0cm7TOjOPB+tt
E4c3JqTZ7g8a5yMe8ItkVhz5pPY+oVw8dxMNRp6Sup5Dbfx0DjacIwLasLsHfPL7
qBADfqB20ovHUzLjXu7oWgEd4KxJ6kiSCaJJu/KD36hg0wB8+WVP1o43j4PkczHT
QjU7eZaeaTrN5Cf34ttPge6QReMi5SFNCaA9O9/HLqrQgdEtt/diZWuqjQ==
=a2mC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Build system fixes and cleanups
* DMA support in the multiboot option ROM
* Rename default-bus-bypass-iommu
* Deprecate -watchdog and cleanup -watchdog-action
* HVF fix for <PAGE_SIZE regions
* Support TSC scaling for AMD nested virtualization
* Fix for ESP fuzzing bug
# gpg: Signature made Tue 02 Nov 2021 10:57:37 AM EDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
* remotes/bonzini/tags/for-upstream: (27 commits)
configure: fix --audio-drv-list help message
configure: Remove the check for the __thread keyword
Move the l2tpv3 test from configure to meson.build
meson: remove unnecessary coreaudio test program
meson: remove pointless warnings
meson.build: Allow to disable OSS again
meson: bump submodule to 0.59.3
qtest/am53c974-test: add test for cancelling in-flight requests
esp: ensure in-flight SCSI requests are always cancelled
KVM: SVM: add migration support for nested TSC scaling
hw/i386: fix vmmouse registration
watchdog: remove select_watchdog_action
vl: deprecate -watchdog
watchdog: add information from -watchdog help to -device help
hw/i386: Rename default_bus_bypass_iommu
hvf: Avoid mapping regions < PAGE_SIZE as ram
configure: do not duplicate CPU_CFLAGS into QEMU_LDFLAGS
configure: remove useless NPTL probe
target/i386: use DMA-enabled multiboot ROM for new-enough QEMU machine types
optionrom: add a DMA-enabled multiboot ROM
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This command was turned into a no-op four years ago in
commit 0c8465440d
Author: Peter Xu <peterx@redhat.com>
Date: Fri Dec 29 15:31:04 2017 +0800
hmp: obsolete "info ioapic"
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Record cr2, error_code, and exception_index. That last means
that we must exit to cpu_loop ourselves, instead of letting
exception_index being overwritten.
Use the maperr parameter to properly set PG_ERROR_P_MASK.
Reviewed by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
I noticed -cpu help printing enough trailing spaces to make the output
at least 84 characters wide. Looks ugly unless the terminal is wider.
Ugly or not, trailing spaces are stupid.
The culprit is this line in x86_cpu_list_entry():
qemu_printf("x86 %-20s %-58s\n", name, desc);
This prints a string with minimum field left-justified right before a
newline. Change it to
qemu_printf("x86 %-20s %s\n", name, desc);
which avoids the trailing spaces and is simpler to boot.
A search for the pattern with "git-grep -E '%-[0-9]+s\\n'" found a few
more instances. Change them similarly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20211009152401.2982862-1-armbru@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Because core-capability releated features are model-specific and KVM
won't support it, remove the core-capability in CPU model to avoid the
warning message.
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Message-Id: <20210827064818.4698-3-chenyi.qiang@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We were using singlestep_enabled as a proxy for whether
translator_use_goto_tb would always return false.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add cpu_ld/st_mmu memory primitives.
Move helper_ld/st memory helpers out of tcg.h.
Canonicalize alignment flags in MemOp.
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmFnG/0dHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV/P8Qf/TIb+nP/q4ZesoHV5
hNuKIMcGMiIWjP7YkuXg7H8n4QQxSK+nKXI3qlWCTIVtKOQFC3jkqNnxV8ncHUyS
RW6ePEcmJfb+yv20MnDLObxMcAq6mIkHtOjARQcvcHiXxMNEZdIvJ8f8/qrkYib1
RRJarqIGlYFJvGyfbplq/JA/WYcJleIElEUx7JPSewz38Kk0gDIH2+BR2TBFrWAD
TDfh+GvlHeX8IYU19rWnt7pFv8TVPVQODqJBtlRPEYnl+LGdpJPCP2ATUAggWHiA
hucYKsuMWXXXhGx2nsurkpSNrBfGe6OHybOE5d1ARqmq0MnyHJat+ryh6qTx3Z9w
oZKi+Q==
=QpK0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth/tags/pull-tcg-20211013' into staging
Use MO_128 for 16-byte atomic memory operations.
Add cpu_ld/st_mmu memory primitives.
Move helper_ld/st memory helpers out of tcg.h.
Canonicalize alignment flags in MemOp.
# gpg: Signature made Wed 13 Oct 2021 10:48:45 AM PDT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [ultimate]
* remotes/rth/tags/pull-tcg-20211013:
tcg: Canonicalize alignment flags in MemOp
tcg: Move helper_*_mmu decls to tcg/tcg-ldst.h
target/arm: Use cpu_*_mmu instead of helper_*_mmu
target/sparc: Use cpu_*_mmu instead of helper_*_mmu
target/s390x: Use cpu_*_mmu instead of helper_*_mmu
target/mips: Use 8-byte memory ops for msa load/store
target/mips: Use cpu_*_data_ra for msa load/store
accel/tcg: Move cpu_atomic decls to exec/cpu_ldst.h
accel/tcg: Add cpu_{ld,st}*_mmu interfaces
target/hexagon: Implement cpu_mmu_index
target/s390x: Use MO_128 for 16 byte atomics
target/ppc: Use MO_128 for 16 byte atomics
target/i386: Use MO_128 for 16 byte atomics
target/arm: Use MO_128 for 16 byte atomics
memory: Log access direction for invalid accesses
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The struct kvm_sev_launch_measure has a constant and small size, and
therefore we can use a regular local variable for it instead of
allocating and freeing heap memory for it.
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20211011173026.2454294-3-dovmurik@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The struct kvm_sev_launch_start has a constant and small size, and
therefore we can use a regular local variable for it instead of
allocating and freeing heap memory for it.
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20211011173026.2454294-2-dovmurik@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move qmp_query_sgx() and hmp_info_sgx() from target/i386/monitor.c
to hw/i386/sgx.c, removing the sgx_get_info() indirection and the
"hw/i386/sgx.h" header.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007175612.496366-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move qmp_query_sgx_capabilities() from target/i386/monitor.c to
hw/i386/sgx.c, removing the sgx_get_capabilities() indirection.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007175612.496366-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While being conditionally used for TARGET_I386 in hmp-commands-info.hx,
hmp_info_sev() is declared for all targets. Reduce its declaration
to target including "monitor/hmp-target.h". This is a minor cleanup.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-23-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move qmp_query_sev() & hmp_info_sev()() from monitor.c to sev.c
and make sev_get_info() static. We don't need the stub anymore,
remove it. Add a stub for hmp_info_sev().
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-22-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move qmp_query_sev_launch_measure() from monitor.c to sev.c
and make sev_get_launch_measurement() static. We don't need the
stub anymore, remove it.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-21-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move qmp_query_sev_capabilities() from monitor.c to sev.c
and make sev_get_capabilities() static. We don't need the
stub anymore, remove it.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-20-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move qmp_sev_inject_launch_secret() from monitor.c to sev.c
and make sev_inject_launch_secret() static. We don't need the
stub anymore, remove it.
Previously with binaries built without SEV, management layer
was getting an empty response:
{ "execute": "sev-inject-launch-secret",
"arguments": { "packet-header": "mypkt", "secret": "mypass", "gpa": 4294959104 }
}
{
"return": {
}
}
Now the response is explicit, mentioning the feature is disabled:
{ "execute": "sev-inject-launch-secret",
"arguments": { "packet-header": "mypkt", "secret": "mypass", "gpa": 4294959104 }
}
{
"error": {
"class": "GenericError",
"desc": "this feature or command is not currently supported"
}
}
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-19-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move qmp_query_sev_attestation_report() from monitor.c to sev.c
and make sev_get_attestation_report() static. We don't need the
stub anymore, remove it.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-18-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only declare sev_enabled() and sev_es_enabled() when CONFIG_SEV is
set, to allow the compiler to elide unused code. Remove unnecessary
stubs.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20211007161716.453984-17-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
"sysemu/sev.h" is only used from x86-specific files. Let's move it
to include/hw/i386, and merge it with target/i386/sev.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-16-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SEV is a x86 specific feature, and the "sev_i386.h" header
is already in target/i386/. Rename it as "sev.h" to simplify.
Patch created mechanically using:
$ git mv target/i386/sev_i386.h target/i386/sev.h
$ sed -i s/sev_i386.h/sev.h/ $(git grep -l sev_i386.h)
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20211007161716.453984-15-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SEV is irrelevant on user emulation, so restrict it to sysemu.
Some stubs are still required because used in cpu.c by
x86_register_cpudef_types(), so move the sysemu specific stubs
to sev-sysemu-stub.c instead. This will allow us to simplify
monitor.c (which is not available in user emulation) in the
next commit.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-14-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use g_autofree to remove a pair of g_free/goto.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-13-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Removes a whole bunch of g_free's and a goto.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Message-Id: <20210603113017.34922-1-dgilbert@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-12-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The unique sev_encrypt_flash() invocation (in pc_system_flash_map)
is protected by the "if (sev_enabled())" check, so is not
reacheable.
Replace the abort() call in sev_es_save_reset_vector() by
g_assert_not_reached() which meaning is clearer.
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-11-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unused dead code makes review harder, so remove it.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-10-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 00b8105324 ("target-i386: Remove assert_no_error usage")
forgot to add the "qapi/error.h" for &error_abort, add it now.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-8-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the management layer tries to inject a secret, it gets an empty
response in case the guest doesn't have SEV enabled, or the binary
is built without SEV:
{ "execute": "sev-inject-launch-secret",
"arguments": { "packet-header": "mypkt", "secret": "mypass", "gpa": 4294959104 }
}
{
"return": {
}
}
Make it clearer by returning an error:
{ "execute": "sev-inject-launch-secret",
"arguments": { "packet-header": "mypkt", "secret": "mypass", "gpa": 4294959104 }
}
{
"error": {
"class": "GenericError",
"desc": "SEV not enabled for guest"
}
}
Note: we will remove the sev_inject_launch_secret() stub in few commits,
so we don't bother to add error_setg() there.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-7-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Multiple errors might be reported to the monitor,
better to prefix the SEV ones so we can distinct them.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20211007161716.453984-6-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SEV is x86-specific, no need to add its stub to other
architectures. Move the stub file to target/i386/kvm/.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce the i386_softmmu_kvm Meson source set to be able to
add features dependent on CONFIG_KVM.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211007161716.453984-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We're about to move this out of tcg.h, so rename it
as we did when moving MemOp.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add the sev_add_kernel_loader_hashes function to calculate the hashes of
the kernel/initrd/cmdline and fill a designated OVMF encrypted hash
table area. For this to work, OVMF must support an encrypted area to
place the data which is advertised via a special GUID in the OVMF reset
table.
The hashes of each of the files is calculated (or the string in the case
of the cmdline with trailing '\0' included). Each entry in the hashes
table is GUID identified and since they're passed through the
sev_encrypt_flash interface, the hashes will be accumulated by the AMD
PSP measurement (SEV_LAUNCH_MEASURE).
Co-developed-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210930054915.13252-2-dovmurik@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM implements some Hyper-V 2016 functions so providing WS2008R2 version
is somewhat incorrect. While generally guests shouldn't care about it
and always check feature bits, it is known that some tools in Windows
actually check version info.
For compatibility reasons make the change for 6.2 machine types only.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210902093530.345756-9-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, we hardcode Hyper-V version id (CPUID 0x40000002) to
WS2008R2 and it is known that certain tools in Windows check this. It
seems useful to provide some flexibility by making it possible to change
this info at will. CPUID information is defined in TLFS as:
EAX: Build Number
EBX Bits 31-16: Major Version
Bits 15-0: Minor Version
ECX Service Pack
EDX Bits 31-24: Service Branch
Bits 23-0: Service Number
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210902093530.345756-8-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The enlightenment allows to use Hyper-V SynIC with hardware APICv/AVIC
enabled. Normally, Hyper-V SynIC disables these hardware features and
suggests the guest to use paravirtualized AutoEOI feature. Linux-4.15
gains support for conditional APICv/AVIC disablement, the feature
stays on until the guest tries to use AutoEOI feature with SynIC. With
'HV_DEPRECATING_AEOI_RECOMMENDED' bit exposed, modern enough Windows/
Hyper-V versions should follow the recommendation and not use the
(unwanted) feature.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210902093530.345756-7-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation to enabling Hyper-V + APICv/AVIC move
HV_APIC_ACCESS_RECOMMENDED setting out of kvm_hyperv_properties[]: the
'real' feature bit for the vAPIC features is HV_APIC_ACCESS_AVAILABLE,
HV_APIC_ACCESS_RECOMMENDED is a recommendation to use the feature which
we may not always want to give.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210902093530.345756-6-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default, KVM allows the guest to use all currently supported Hyper-V
enlightenments when Hyper-V CPUID interface was exposed, regardless of if
some features were not announced in guest visible CPUIDs. hv-enforce-cpuid
feature alters this behavior and only allows the guest to use exposed
Hyper-V enlightenments. The feature is supported by Linux >= 5.14 and is
not enabled by default in QEMU.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210902093530.345756-5-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default, KVM allows the guest to use all currently supported PV features
even when they were not announced in guest visible CPUIDs. Introduce a new
"kvm-pv-enforce-cpuid" flag to limit the supported feature set to the
exposed features. The feature is supported by Linux >= 5.10 and is not
enabled by default in QEMU.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210902093530.345756-4-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Provide a name field for all the memory listeners. It can be used to identify
which memory listener is which.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210817013553.30584-2-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In sev_read_file_base64() we call g_file_get_contents(), which
allocates memory for the file contents. We then base64-decode the
contents (which allocates another buffer for the decoded data), but
forgot to free the memory for the original file data.
Use g_autofree to ensure that the file data is freed.
Fixes: Coverity CID 1459997
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210820165650.2839-1-peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Libvirt can use query-sgx-capabilities to get the host
sgx capabilities to decide how to allocate SGX EPC size to VM.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210910102258.46648-3-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The QMP and HMP interfaces can be used by monitor or QMP tools to retrieve
the SGX information from VM side when SGX is enabled on Intel platform.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210910102258.46648-2-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SGX capabilities are enumerated through CPUID_0x12.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-16-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SGX sub-leafs are enumerated at CPUID 0x12. Indices 0 and 1 are
always present when SGX is supported, and enumerate SGX features and
capabilities. Indices >=2 are directly correlated with the platform's
EPC sections. Because the number of EPC sections is dynamic and user
defined, the number of SGX sub-leafs is "NULL" terminated.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-15-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the guest want to fully use SGX, the guest needs to be able to
access provisioning key. Add a new KVM_CAP_SGX_ATTRIBUTE to KVM to
support provisioning key to KVM guests.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-14-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose SGX to the guest if and only if KVM is enabled and supports
virtualization of SGX. While the majority of ENCLS can be emulated to
some degree, because SGX uses a hardware-based root of trust, the
attestation aspects of SGX cannot be emulated in software, i.e.
ultimately emulation will fail as software cannot generate a valid
quote/report. The complexity of partially emulating SGX in Qemu far
outweighs the value added, e.g. an SGX specific simulator for userspace
applications can emulate SGX for development and testing purposes.
Note, access to the PROVISIONKEY is not yet advertised to the guest as
KVM blocks access to the PROVISIONKEY by default and requires userspace
to provide additional credentials (via ioctl()) to expose PROVISIONKEY.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-13-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SGX adds multiple flags to FEATURE_CONTROL to enable SGX and Flexible
Launch Control.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-12-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On real hardware, on systems that supports SGX Launch Control, those
MSRs are initialized to digest of Intel's signing key; on systems that
don't support SGX Launch Control, those MSRs are not available but
hardware always uses digest of Intel's signing key in EINIT.
KVM advertises SGX LC via CPUID if and only if the MSRs are writable.
Unconditionally initialize those MSRs to digest of Intel's signing key
when CPU is realized and reset to reflect the fact. This avoids
potential bug in case kvm_arch_put_registers() is called before
kvm_arch_get_registers() is called, in which case guest's virtual
SGX_LEPUBKEYHASH MSRs will be set to 0, although KVM initializes those
to digest of Intel's signing key by default, since KVM allows those MSRs
to be updated by Qemu to support live migration.
Save/restore the SGX Launch Enclave Public Key Hash MSRs if SGX Launch
Control (LC) is exposed to the guest. Likewise, migrate the MSRs if they
are writable by the guest.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-11-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CPUID leaf 12_1_EAX is an Intel-defined feature bits leaf enumerating
the platform's SGX capabilities that may be utilized by an enclave, e.g.
whether or not an enclave can gain access to the provision key.
Currently there are six capabilities:
- INIT: set when the enclave has has been initialized by EINIT. Cannot
be set by software, i.e. forced to zero in CPUID.
- DEBUG: permits a debugger to read/write into the enclave.
- MODE64BIT: the enclave runs in 64-bit mode
- PROVISIONKEY: grants has access to the provision key
- EINITTOKENKEY: grants access to the EINIT token key, i.e. the
enclave can generate EINIT tokens
- KSS: Key Separation and Sharing enabled for the enclave.
Note that the entirety of CPUID.0x12.0x1, i.e. all registers, enumerates
the allowed ATTRIBUTES (128 bits), but only bits 31:0 are directly
exposed to the user (via FEAT_12_1_EAX). Bits 63:32 are currently all
reserved and bits 127:64 correspond to the allowed XSAVE Feature Request
Mask, which is calculated based on other CPU features, e.g. XSAVE, MPX,
AVX, etc... and is not exposed to the user.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-10-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CPUID leaf 12_0_EBX is an Intel-defined feature bits leaf enumerating
the platform's SGX extended capabilities. Currently there is a single
capabilitiy:
- EXINFO: record information about #PFs and #GPs in the enclave's SSA
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-9-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CPUID leaf 12_0_EAX is an Intel-defined feature bits leaf enumerating
the CPU's SGX capabilities, e.g. supported SGX instruction sets.
Currently there are four enumerated capabilities:
- SGX1 instruction set, i.e. "base" SGX
- SGX2 instruction set for dynamic EPC management
- ENCLV instruction set for VMM oversubscription of EPC
- ENCLS-C instruction set for thread safe variants of ENCLS
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-8-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add CPUID defines for SGX and SGX Launch Control (LC), as well as
defines for their associated FEATURE_CONTROL MSR bits. Define the
Launch Enclave Public Key Hash MSRs (LE Hash MSRs), which exist
when SGX LC is present (in CPUID), and are writable when SGX LC is
enabled (in FEATURE_CONTROL).
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-7-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is nothing target specific about this. The implementation
is host specific, but the declaration is 100% common.
Reviewed-By: Warner Losh <imp@bsdimp.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With Apple Silicon available to the masses, it's a good time to add support
for driving its virtualization extensions from QEMU.
This patch adds all necessary architecture specific code to get basic VMs
working, including save/restore.
Known limitations:
- WFI handling is missing (follows in later patch)
- No watchpoint/breakpoint support
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210916155404.86958-5-agraf@csgraf.de
[PMM: added missing #include]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We will need to install a migration helper for the ARM hvf backend.
Let's introduce an arch callback for the overall hvf init chain to
do so.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210916155404.86958-4-agraf@csgraf.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
cpu_get_pic_interrupt() is now unreachable from user-mode,
delete the unnecessary stubs.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210911165434.531552-25-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Following the logic of commit 30493a030f ("i386: split seg_helper
into user-only and sysemu parts"), move x86_cpu_exec_interrupt()
under sysemu/seg_helper.c.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-By: Warner Losh <imp@bsdimp.com>
Message-Id: <20210911165434.531552-12-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Restrict cpu_exec_interrupt() and its callees to sysemu.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210911165434.531552-11-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
do_interrupt() is sysemu specific. However due to some X86
specific hack, it is also used in user-mode emulation, which
is why it couldn't be restricted to CONFIG_SOFTMMU (see the
comment around added in commit 7827168471: "cpu: tcg_ops:
move to tcg-cpu-ops.h, keep a pointer in CPUClass").
Keep the hack but rename the handler as fake_user_interrupt()
and restrict do_interrupt() to sysemu.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210911165434.531552-6-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Merge two TARGET_X86_64 consecutive blocks.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210911165434.531552-4-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Restrict some sysemu-only fpu_helper helpers (see commit
83a3d9c740: "i386: separate fpu_helper sysemu-only parts").
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210911165434.531552-3-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
[rth: Split out of a larger patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
A parameter max_size was added to the RAMBlockNotifier
ram_block_added function. Use the max_size for pre allocation
of hva space.
Signed-off-by: Reinoud Zandijk <Reinoud@NetBSD.org>
Message-Id: <20210718134650.1191-3-reinoud@NetBSD.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The feature allows the VMSAVE and VMLOAD instructions to execute in guest mode without
causing a VMEXIT. (APM2 15.33.1)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Writes to cr8 affect v_tpr. This could set or unset an interrupt
request as the priority might have changed.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The APM2 states that if V_IGN_TPR is nonzero, the current
virtual interrupt ignores the (virtual) TPR.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VGIF provides masking capability for when virtual interrupts
are taken. (APM2)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Moved int_ctl into the CPUX86State structure. It removes some
unnecessary stores and loads, and prepares for tracking the vIRQ
state even when it is masked due to vGIF.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VGIF allows STGI and CLGI to execute in guest mode and control virtual
interrupts in guest mode.
When the VGIF feature is enabled then:
* executing STGI in the guest sets bit 9 of the VMCB offset 60h.
* executing CLGI in the guest clears bit 9 of the VMCB offset 60h.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210730070742.9674-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
APM2 requires that VMRUN and VMLOAD canonicalize (sign extend to 63
from 48/57) all base addresses in the segment registers that have been
respectively loaded.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210804113058.45186-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Booting Fedora kernels with -cpu max hangs very early in boot. Disabling
the la57 CPUID bit fixes the problem. git bisect traced the regression to
commit 213ff024a2 (HEAD, refs/bisect/bad)
Author: Lara Lazier <laramglazier@gmail.com>
Date: Wed Jul 21 17:26:50 2021 +0200
target/i386: Added consistency checks for CR4
All MBZ bits in CR4 must be zero. (APM2 15.5)
Added reserved bitmask and added checks in both
helper_vmrun and helper_write_crN.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210721152651.14683-2-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In this commit CR4_RESERVED_MASK is missing CR4_LA57_MASK and
two others. Adding this lets Fedora kernels boot once again.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Message-Id: <20210831175033.175584-1-berrange@redhat.com>
[Removed VMXE/SMXE, matching the commit message. - Paolo]
Fixes: 213ff024a2 ("target/i386: Added consistency checks for CR4", 2021-07-22)
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most callers check the return value. Some check whether it set an
error. Functionally equivalent, but the former tends to be easier on
the eyes, so do that everywhere.
Prior art: commit c6ecec43b2 "qemu-option: Check return value instead
of @err where convenient".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210720125408.387910-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
There is nothing to delete after migrate_add_blocker() failed. Trying
anyway is safe, but useless. Don't.
Cc: Sunil Muthuswamy <sunilmut@microsoft.com>
Cc: Kamil Rytarowski <kamil@netbsd.org>
Cc: Reinoud Zandijk <reinoud@netbsd.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210720125408.387910-9-armbru@redhat.com>
Reviewed-by: Reinoud Zandijk <reinoud@NetBSD.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
invtsc_mig_blocker has static storage duration. When a CPU with
certain features is initialized, and invtsc_mig_blocker is still null,
we add a migration blocker and store it in invtsc_mig_blocker.
The object is freed when migrate_add_blocker() fails, leaving
invtsc_mig_blocker dangling. It is not freed on later failures.
Same for hv_passthrough_mig_blocker and hv_no_nonarch_cs_mig_blocker.
All failures are actually fatal, so whether we free or not doesn't
really matter, except as bad examples to be copied / imitated.
Clean this up in a minimal way: never free these blocker objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210720125408.387910-7-armbru@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
We did this with scripts/coccinelle/use-error_fatal.cocci before, in
commit 50beeb6809 and 007b06578a. This commit cleans up rarer
variations that don't seem worth matching with Coccinelle.
Cc: Thomas Huth <thuth@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210720125408.387910-2-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The AVX_VNNI feature is not in Cooperlake platform, remove it
from cpu model.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210820054611.84303-1-yang.zhong@intel.com>
Fixes: c1826ea6a0 ("i386/cpu: Expose AVX_VNNI instruction to guest")
Cc: qemu-stable@nongnu.org
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
At present, there's no mechanism intelligent enough to virtualize split
lock detection correctly. Remove it in Snowridge CPU model to avoid the
feature exposure.
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Message-Id: <20210630012053.10098-1-chenyi.qiang@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
~0UL has 64 bits on Linux and 32 bits on Windows.
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/512
Reported-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210812111056.26926-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The shift constant was incorrect, causing int_prio to always be zero.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
[Rewritten commit message since v1 had already been included. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMRUN exits with SVM_EXIT_ERR if either:
* The event injected has a reserved type.
* When the event injected is of type 3 (exception), and the vector that
has been specified does not correspond to an exception.
This does not fix the entire exc_inj test in kvm-unit-tests.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210725090855.19713-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Coverity reports potential NULL pointer dereference in
get_supported_hv_cpuid_legacy() when 'cs->kvm_state' is NULL. While
'cs->kvm_state' can indeed be NULL in hv_cpuid_get_host(),
kvm_hyperv_expand_features() makes sure that it only happens when
KVM_CAP_SYS_HYPERV_CPUID is supported and KVM_CAP_SYS_HYPERV_CPUID
implies KVM_CAP_HYPERV_CPUID so get_supported_hv_cpuid_legacy() is
never really called. Add asserts to strengthen the protection against
broken KVM behavior.
Coverity: CID 1458243
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210716115852.418293-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Missed in commit f3478392 "docs: Move deprecation, build
and license info out of system/"
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210723065828.1336760-1-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some cpu properties have to be set only for cpu models in builtin_x86_defs,
registered with x86_register_cpu_model_type, and not for
cpu models "base", "max", and the subclass "host".
These properties are the ones set by function x86_cpu_apply_props,
(also including kvm_default_props, tcg_default_props),
and the "vendor" property for the KVM and HVF accelerators.
After recent refactoring of cpu, which also affected these properties,
they were instead set unconditionally for all x86 cpus.
This has been detected as a bug with Nested on AMD with cpu "host",
as svm was not turned on by default, due to the wrongful setting of
kvm_default_props via x86_cpu_apply_props, which set svm to "off".
Rectify the bug introduced in commit "i386: split cpu accelerators"
and document the functions that are builtin_x86_defs-only.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: f5cc5a5c ("i386: split cpu accelerators from cpu.c,"...)
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/477
Message-Id: <20210723112921.12637-1-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All MBZ in CR3 must be zero (APM2 15.5)
Added checks in both helper_vmrun and helper_write_crN.
When EFER.LMA is zero the upper 32 bits needs to be zeroed.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210723112740.45962-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
EFER.SVME has to be set, and EFER reserved bits must
be zero.
In addition the combinations
* EFER.LMA or EFER.LME is non-zero and the processor does not support LM
* non-zero EFER.LME and CR0.PG and zero CR4.PAE
* non-zero EFER.LME and CR0.PG and zero CR0.PE
* non-zero EFER.LME, CR0.PG, CR4.PAE, CS.L and CS.D
are all invalid.
(AMD64 Architecture Programmer's Manual, V2, 15.5)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210721152651.14683-3-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All MBZ bits in CR4 must be zero. (APM2 15.5)
Added reserved bitmask and added checks in both
helper_vmrun and helper_write_crN.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210721152651.14683-2-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The APM2 states that The processor takes a virtual INTR interrupt
if V_IRQ and V_INTR_PRIO indicate that there is a virtual interrupt pending
whose priority is greater than the value in V_TPR.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210721152651.14683-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The hook is now unused, with breakpoints checked outside translation.
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Return false for RF set, as we do in i386_tr_breakpoint_check.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Always provide the atomic interface using TCGMemOpIdx oi
and uintptr_t retaddr. Rename from helper_* to cpu_* so
as to (mostly) match the exec/cpu_ldst.h functions, and
to emphasize that they are not callable from TCG directly.
Tested-by: Cole Robinson <crobinso@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Implement x86 fcs:fip, fds:fdp.
Trivial x86 watchpoint cleanup.
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmDtwQ0dHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV/GnAf/SYNhdmIuKCWk/uk8
IC0v2sm5KHVFfkfkobQ+04pFB26tX557i2zTtEfj/A5QVlJSvliZowCVIO6JV63N
9oedLSzdqrxRqDb+Mpmkwnam/k5XfrC20V7os17FuZE98u3Jgky8QNs7Uxq0bCBZ
01AKB9HNRFKeY2o55IxPwC7CLtyz3SStJJP28aa5ROYK7MIP303qsI5pezgkHgGo
/qo5GXwHs/Pu4pnFuAJyOfG38wT6uTt7NrAGjTH0VhbAKNMSP/QND+VvxbuCugZR
6MEVeb+rLy+MN4b3dH6kI89JQvQGBCaWZD/eTF5+8UDPj3I8vpRqufRh8l5WukT1
Q2g1zA==
=eqkT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth-gitlab/tags/pull-misc-20210713' into staging
Cleanup alpha, hppa, or1k wrt tcg_constant_tl.
Implement x86 fcs:fip, fds:fdp.
Trivial x86 watchpoint cleanup.
# gpg: Signature made Tue 13 Jul 2021 17:36:29 BST
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth-gitlab/tags/pull-misc-20210713:
target/hppa: Clean up DisasCond
target/hppa: Use tcg_constant_*
target/openrisc: Use dc->zero in gen_add, gen_addc
target/openrisc: Cache constant 0 in DisasContext
target/openrisc: Use tcg_constant_tl for dc->R0
target/openrisc: Use tcg_constant_*
target/alpha: Use tcg_constant_* elsewhere
target/alpha: Use tcg_constant_i64 for zero and lit
target/alpha: Use dest_sink for HW_RET temporary
target/alpha: Store set into rx flag
target/i386: Correct implementation for FCS, FIP, FDS and FDP
target/i386: Split out do_fninit
target/i386: Trivial code motion and code style fix
target/i386: Tidy hw_breakpoint_remove
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update FCS:FIP and FDS:FDP according to the Intel Manual Vol.1 8.1.8.
Note that CPUID.(EAX=07H,ECX=0H):EBX[bit 13] is not implemented by
design in this patch and will be added along with TCG features flag
in a separate patch later.
Signed-off-by: Ziqiao Kong <ziqiaokong@gmail.com>
Message-Id: <20210530150112.74411-2-ziqiaokong@gmail.com>
[rth: Push FDS/FDP handling down into mod != 3 case; free last_addr.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Do not call helper_fninit directly from helper_xrstor.
Do call the new helper from do_fsave.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
A new pair of braces has to be added to declare variables in the case block.
The code style is also fixed according to the transalte.c itself during the
code motion.
Signed-off-by: Ziqiao Kong <ziqiaokong@gmail.com>
Message-Id: <20210530150112.74411-1-ziqiaokong@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since cpu_breakpoint and cpu_watchpoint are in a union,
the code should access only one of them.
Signed-off-by: Dmitry Voronetskiy <davoronetskiy@gmail.com>
Message-Id: <20210613180838.21349-1-davoronetskiy@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
A AMD server typically has cpuid level 0x10(test on Rome/Milan), it
should not be changed to 0x1f in multi-dies case.
* to maintain compatibility with older machine types, only implement
this change when the CPU's "x-vendor-cpuid-only" property is false
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: zhenwei pi <pizhenwei@bytedance.com>
Fixes: a94e142899 (target/i386: Add CPUID.1F generation support for multi-dies PCMachine)
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-Id: <20210708170641.49410-1-michael.roth@amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
