Remove the get_system_memory() call from serial_mm_init, pushing
it back into the callers. In many cases we already have the
system memory region available.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
The use of DEVICE_NATIVE_ENDIAN cleans up lots of ifdefs in
many of the callers.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
Slightly non-obvious with mips_jazz passing in the region
structure to populate.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
Not used yet, but at least we're provided with the correct region.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
Extract G364 ROM contents from device emulation to machine emulation,
so device emulation can be reused in other machines (Commodore Amiga)
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This reverts commit 8ef9ea85a2, reversing
changes made to 444dc48298.
From Avi:
Please revert the entire pull (git revert 8ef9ea85a2) while I work this
out - it isn't trivial.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Instead, use the bus accessors, or get the address space directly
from the board constructor.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch converts the ISA MMIO bridge code to always use little endian mmio.
All bswap code that existed was only there to convert from native cpu
endianness to little endian ISA devices.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As stated before, devices can be little, big or native endian. The
target endianness is not of their concern, so we need to push things
down a level.
This patch adds a parameter to cpu_register_io_memory that allows a
device to choose its endianness. For now, all devices simply choose
native endian, because that's the same behavior as before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Sending ESP a command caused it to trigger DMA immediately
even if DMA was not enabled at the DMA controller.
Add a signal from DMA controller to ESP to tell ESP about changes in
DMA enable bit. Also use the correct function for setting up GPIO outputs.
This fixes NetBSD 1.6.1 through 3.0 boot.
Thanks to Artyom Tarasenko for extensive debugging of the problem.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Changing block.h or blockdev.h resulted in recompiling most objects.
Move DriveInfo typedef and BlockInterfaceType enum definitions
to qemu-common.h and rearrange blockdev.h use to decrease churn.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
These will be used to generate unique id strings for ramblocks. The name
field is required, the device pointer is optional as most callers don't
have a device. When there's no device or the device isn't a child of
a bus implementing BusInfo.get_dev_path, the name should be unique for
the platform.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
System architecture dictates whether HAS_AUDIO is defined. It's then
useless to check for HAS_AUDIO in files which are only used on those
architectures which always have audio.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Allow the intercept the RTC IRQ for the HPET legacy mode. Then push
routing to IRQ8 completely into the HPET. This allows to turn
hpet_in_legacy_mode() into a private function. Furthermore, this stops
the RTC from clearing IRQ8 even if the HPET is in control.
This patch comes with a side effect: The RTC timers will no longer be
stoppend when there is no IRQ consumer, possibly causing a minor
performance degration. But as the guest may want to redirect the RTC to
the SCI in that mode, it should normally disable unused IRQ source
anyway.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
To match rtc_xxx with qdev, make rtc_xxx accept and return ISADevice
instead of RTCState.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As i8259 in mips_jazz.c is not correctly connected to the isa bus, the
mc146818rtc isa devices fails to be created.
Signed-off-by: Roy Tam <roytam@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We now only assign strdup()ed strings to these fields, never static
strings.
aliguori: fix build for ppc_prep and mips_jazz
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The CPU state parameter is not used, remove it and adjust callers. Now we
can compile ioport.c once for all targets.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Callers must pass ELF machine, byte swapping and symbol LSB clearing
information to ELF loader. A.out loader needs page size information, pass
that too as a parameter.
Extract prototypes to a separate file. Move loader.[ch] and elf_ops.h under hw.
Adjust callers. Also use target_phys_addr_t instead of target_ulong for
addresses: loader addresses aren't virtual.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Changes:
(1) make isa-bus maintain isa irqs, complain when allocating
already taken irqs.
(2) note that (1) works only for isa devices converted to qdev
already (floppy and ps2/kbd/mouse right now), so more work
is needed to make this really useful.
(3) split floppy init into isa and sysbus versions.
(4) add sysbus->isa bridge & fix -M isapc breakage.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
First step cleaning up the drives handling. This one does nothing but
removing drives_table[], still it became seriously big.
drive_get_index() is gone and is replaced by drives_get() which hands
out DriveInfo pointers instead of a table index. This needs adaption in
*tons* of places all over.
The drives are now maintained as linked list.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The parameter is always zero except when registering the three internal
io regions (ROM, unassigned, notdirty). Remove the parameter to reduce
the API's power, thus facilitating future change.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add the parameter 'order' to qemu_register_reset and sort callbacks on
registration. On system reset, callbacks with lower order will be
invoked before those with higher order. Update all existing users to the
standard order 0.
Note: At least for x86, the existing users seem to assume that handlers
are called in their registration order. Therefore, the patch preserves
this property. If someone feels bored, (s)he could try to identify this
dependency and express it properly on callback registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The vga_ram_size argument to machine init functions always has the same
value, and is ignored by many machines (including SPARC32 which has an
obsolete ifdef for VGA_RAM_SIZE).
Remove it and push VGA_RAM_SIZE into vga_int.h.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Now we can safely call AUD_init multiple times we can push it down to
individual audio devices, rather than having to pass it from the board
init.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Failure to initialize the audio subsystem is not handled consistently.
Where it is handled it has guest visible effects, which is wrong.
We already have a "nosound" audio driver as a last resort, so trying to
proceed without an audio backend seems pointless.
Also protect against multiple calls to AUD_init so that this can be
pushed down into individual devices.
Signed-off-by: Paul Brook <paul@codesourcery.com>
