Keyboard-Controller-Style devices for IPMI purposes are exposed via LPC
IO cycles from the BMC to the host.
Expose support on the BMC side by implementing the usual MMIO
behaviours, and expose the ability to inspect the KCS registers in
"host" style by accessing QOM properties associated with each register.
The model caters to the IRQ style of both the AST2600 and the earlier
SoCs (AST2400 and AST2500). The AST2600 allocates an IRQ for each LPC
sub-device, while there is a single IRQ shared across all subdevices on
the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-6-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a very minimal framework to access registers which are used to
configure the AHB memory mapping of the flash chips on the LPC HC
Firmware address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-Id: <20210302014317.915120-5-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Update old infocenter.arm.com URLs to the equivalent developer.arm.com
ones (the old URLs should redirect, but we might as well avoid the
redirection notice, and the new URLs are pleasantly shorter).
This commit covers the links to the MPS2 board TRM, the various
Application Notes, the IoTKit and SSE-200 documents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-25-peter.maydell@linaro.org
The AN524 version of the SCC interface has different behaviour for
some of the CFG registers; implement it.
Each board in this family can have minor differences in the meaning
of the CFG registers, so rather than trying to specify all the
possible semantics via individual device properties, we make the
behaviour conditional on the part-number field of the SCC_ID register
which the board code already passes us.
For the AN524, the differences are:
* CFG3 is reserved rather than being board switches
* CFG5 is a new register ("ACLK Frequency in Hz")
* CFG6 is a new register ("Clock divider for BRAM")
We implement both of the new registers as reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-11-peter.maydell@linaro.org
MPS3 boards have an extra SWITCH register in the FPGAIO block which
reports the value of some switches. Implement this, governed by a
property the board code can use to specify whether whether it exists.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-7-peter.maydell@linaro.org
The MPS2 board has 2 LEDs, but the MPS3 board has 10 LEDs. The
FPGAIO device is similar on both sets of boards, but the LED0
register has correspondingly more bits that have an effect. Add a
device property for number of LEDs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-6-peter.maydell@linaro.org
Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6
OSCCLK values. Switch to using a PROP_ARRAY, which allows board code
to specify how large the OSCCLK array should be as well as its
values.
With a variable-length property array, the SCC no longer specifies
default values for the OSCCLKs, so we must set them explicitly in the
board code. This defaults are actually incorrect for the an521 and
an505; we will correct this bug in a following patch.
This is a migration compatibility break for all the mps boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-3-peter.maydell@linaro.org
At present when blk_pread() / blk_pwrite() fails, a guest error
is logged, but this is not really a guest error. Change to use
error_report() instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1611026585-29971-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Several SPDX headers contain "SPDX-License-Identifer" (note the
missing "i" before "er"); fix these typos.
Signed-off-by: Ryan Finnie <ryan@finnie.org>
Cc: qemu-trivial@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210201200147.211914-1-ryan@finnie.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Update infocenter.arm.com URLs for various pieces of Arm
documentation to the new developer.arm.com equivalents. (There is a
redirection in place from the old URLs, but we might as well update
our comments in case the redirect ever disappears in future.)
This patch covers all the URLs which are not MPS2/SSE-200/IoTKit
related (those are dealt with in a different patch).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210205171456.19939-1-peter.maydell@linaro.org
Allow RAM MemoryRegion to be created from an offset in a file, instead
of allocating at offset of 0 by default. This is needed to synchronize
RAM between QEMU & remote process.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 609996697ad8617e3b01df38accc5c208c24d74e.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add PCI interface support for PVPANIC device. Create a new file pvpanic-pci.c
where the PCI specific routines reside and update the build system with the new
files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To ease the PCI device addition in next patches, split the code as follows:
- generic code (read/write/setup) is being kept in pvpanic.c
- ISA dependent code moved to pvpanic-isa.c
Also, rename:
- ISA_PVPANIC_DEVICE -> PVPANIC_ISA_DEVICE.
- TYPE_PVPANIC -> TYPE_PVPANIC_ISA.
- MemoryRegion io -> mr.
- pvpanic_ioport_* in pvpanic_*.
Update the build system with the new files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix potential overflow problem when calculating pwm_duty.
1. Ensure p->cmr and p->cnr to be from [0,65535], according to the
hardware specification.
2. Changed duty to uint32_t. However, since MAX_DUTY * (p->cmr+1)
can excceed UINT32_MAX, we convert them to uint64_t in computation
and converted them back to uint32_t.
(duty is guaranteed to be <= MAX_DUTY so it won't overflow.)
Fixes: CID 1442342
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Doug Evans <dje@google.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210127011142.2122790-1-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, blk_is_read_only() tells whether a given BlockBackend can
only be used in read-only mode because its root node is read-only. Some
callers actually try to answer a slightly different question: Is the
BlockBackend configured to be writable, by taking write permissions on
the root node?
This can differ, for example, for CD-ROM devices which don't take write
permissions, but may be backed by a writable image file. scsi-cd allows
write requests to the drive if blk_is_read_only() returns false.
However, the write request will immediately run into an assertion
failure because the write permission is missing.
This patch introduces separate functions for both questions.
blk_supports_write_perm() answers the question whether the block
node/image file can support writable devices, whereas blk_is_writable()
tells whether the BlockBackend is currently configured to be writable.
All calls of blk_is_read_only() are converted to one of the two new
functions.
Fixes: https://bugs.launchpad.net/bugs/1906693
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210118123448.307825-2-kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When running device-introspect-test, a memory leak occurred in the mos6522_init
function, this patch use timer_free() in the finalize function to fix it.
ASAN shows memory leak stack:
Direct leak of 96 byte(s) in 2 object(s) allocated from:
#0 0xfffd5fe9e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xfffd5f7b6800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaae50303d0c in timer_new_full qemu/include/qemu/timer.h:523
#3 0xaaae50303d0c in timer_new qemu/include/qemu/timer.h:544
#4 0xaaae50303d0c in timer_new_ns qemu/include/qemu/timer.h:562
#5 0xaaae50303d0c in mos6522_init qemu/hw/misc/mos6522.c:490
#6 0xaaae50b77d70 in object_init_with_type qemu/qom/object.c:371
#7 0xaaae50b7ae84 in object_initialize_with_type qemu/qom/object.c:515
#8 0xaaae50b7b0f8 in object_new_with_type qemu/qom/object.c:729
#9 0xaaae50bb6d58 in qmp_device_list_properties qemu/qom/qom-qmp-cmds.c:153
#10 0xaaae50d7e1dc in qmp_marshal_device_list_properties qemu/qapi/qapi-commands-qdev.c:59
#11 0xaaae50dc87a0 in do_qmp_dispatch_bh qemu/qapi/qmp-dispatch.c:110
#12 0xaaae50d931a0 in aio_bh_call qemu/util/async.c:136
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210112112705.380534-3-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Fix code coverage issues by checking return value and handling fail case
of blk_pread() and blk_pwrite(). Return default value 0xff if read fails.
Fixes: Coverity CID 1435959
Fixes: Coverity CID 1435960
Fixes: Coverity CID 1435961
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201104092900.21214-1-green.wan@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Now that all of the object property links to the heathrow PIC and OpenPIC have
been removed from the macio devices, it is safe to allow the macio-oldworld
and macio-neworld devices to be marked as user_creatable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201229175619.6051-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This both allows the wiring to be done as Ben suggested in his original comment in
gpio.c and also enables the OpenPIC object property link to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201229175619.6051-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The OpenPIC device is located within the macio device on real hardware so make it
a child of the macio-newworld device. This also removes the need for setting and
checking a separate PIC object property link on the macio-newworld device which
currently causes the automated QOM introspection tests to fail.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The heathrow PIC is located within the macio device on real hardware so make it
a child of the macio-oldworld device. This also removes the need for setting and
checking a separate PIC object property link on the macio-oldworld device which
currently causes the automated QOM introspection tests to fail.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
A device shouldn't access its parent object which is QOM internal.
Instead it should use type cast for this purporse. This patch fixes this
issue for all NPCM7XX Devices.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210108190945.949196-7-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PWM module is part of NPCM7XX module. Each NPCM7XX module has two
identical PWM modules. Each module contains 4 PWM entries. Each PWM has
two outputs: frequency and duty_cycle. Both are computed using inputs
from software side.
This module does not model detail pulse signals since it is expensive.
It also does not model interrupts and watchdogs that are dependant on
the detail models. The interfaces for these are left in the module so
that anyone in need for these functionalities can implement on their
own.
The user can read the duty cycle and frequency using qom-get command.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-5-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows NPCM7XX CLK module to compute clocks that are used by
other NPCM7XX modules.
Add a new struct NPCM7xxClockConverterState which represents a
single converter. Each clock converter in CLK module represents one
converter in NPCM7XX CLK Module(PLL, SEL or Divider). Each converter
takes one or more input clocks and converts them into one output clock.
They form a clock hierarchy in the CLK module and are responsible for
outputing clocks for various other modules in an NPCM7XX SoC.
Each converter has a function pointer called "convert" which represents
the unique logic for that converter.
The clock contains two initialization information: ConverterInitInfo and
ConverterConnectionInfo. They represent the vertices and edges in the
clock diagram respectively.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210108190945.949196-2-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently when U-Boot boots, it prints "??" for i.MX processor:
CPU: Freescale i.MX?? rev1.0 at 792 MHz
The register that was used to determine the silicon type is
undocumented in the latest IMX6DQRM (Rev. 6, 05/2020), but we
can refer to get_cpu_rev() in arch/arm/mach-imx/mx6/soc.c in
the U-Boot source codes that USB_ANALOG_DIGPROG is used.
Update its reset value to indicate i.MX6Q.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210106063504.10841-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
U-Boot expects PMU_MISC0 register bit 7 is set (see init_bandgap()
in arch/arm/mach-imx/mx6/soc.c) during boot. This bit indicates the
bandgap has stabilized.
With this change, the latest upstream U-Boot (v2021.01-rc3) for imx6
sabrelite board (mx6qsabrelite_defconfig), with a slight change made
by switching CONFIG_OF_SEPARATE to CONFIG_OF_EMBED, boots to U-Boot
shell on QEMU with the following command:
$ qemu-system-arm -M sabrelite -smp 4 -m 1G -kernel u-boot \
-display none -serial null -serial stdio
Boot log below:
U-Boot 2021.01-rc3 (Dec 12 2020 - 17:40:02 +0800)
CPU: Freescale i.MX?? rev1.0 at 792 MHz
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Lite Board
Board: SABRE Lite
I2C: ready
DRAM: 1 GiB
force_idle_bus: sda=0 scl=0 sda.gp=0x5c scl.gp=0x55
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0x6d scl.gp=0x6c
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0xcb scl.gp=0x5
force_idle_bus: failed to clear bus, sda=0 scl=0
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - No block device, using default environment
In: serial
Out: serial
Err: serial
Net: Board Net Initialization Failed
No ethernet found.
starting USB...
Bus usb@2184000: usb dr_mode not found
USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found
scanning bus usb@2184200 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit any key to stop autoboot: 0
=>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210106063504.10841-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
-----BEGIN PGP SIGNATURE-----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=lHZA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20201215' into staging
target-arm queue:
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
# gpg: Signature made Tue 15 Dec 2020 13:59:46 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20201215:
hw/block/m25p80: Fix Numonyx fast read dummy cycle count
hw/block/m25p80: Check SPI mode before running some Numonyx commands
hw/block/m25p80: Fix when VCFG XIP bit is set for Numonyx
hw/block/m25p80: Make Numonyx config field names more accurate
hw/misc/zynq_slcr: Avoid #DIV/0! error
arm: xlnx-versal: Connect usb to virt-versal
usb: xlnx-usb-subsystem: Add xilinx usb subsystem
usb: Add DWC3 model
usb: Add versal-usb2-ctrl-regs module
elf_ops.h: Be more verbose with ROM blob names
elf_ops.h: Don't truncate name of the ROM blobs we create
hw/core/loader.c: Improve reporting of ROM overlap errors
hw/core/loader.c: Track last-seen ROM in rom_check_and_register_reset()
target/nios2: Use deposit32() to update ipending register
target/nios2: Move nios2_check_interrupts() into target/nios2
target/nios2: Move IIC code into CPU object proper
target/openrisc: Move pic_cpu code into CPU object proper
hw/openrisc/openrisc_sim: Abstract out "get IRQ x of CPU y"
hw/openrisc/openrisc_sim: Use IRQ splitter when connecting IRQ to multiple CPUs
gdbstub: Correct misparsing of vCont C/S requests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Malicious user can set the feedback divisor for the PLLs
to zero, triggering a floating-point exception (SIGFPE).
As the datasheet [*] is not clear how hardware behaves
when these bits are zeroes, use the maximum divisor
possible (128) to avoid the software FPE.
[*] Zynq-7000 TRM, UG585 (v1.12.2)
B.28 System Level Control Registers (slcr)
-> "Register (slcr) ARM_PLL_CTRL"
25.10.4 PLLs
-> "Software-Controlled PLL Update"
Fixes: 38867cb7ec ("hw/misc/zynq_slcr: add clock generation for uarts")
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20201210141610.884600-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In order to use inclusive terminology, rename SSI 'slave' as
'peripheral', following the specification resolution:
https://www.oshwa.org/a-resolution-to-redefine-spi-signal-names/
Patch created mechanically using:
$ sed -i s/SSISlave/SSIPeripheral/ $(git grep -l SSISlave)
$ sed -i s/SSI_SLAVE/SSI_PERIPHERAL/ $(git grep -l SSI_SLAVE)
$ sed -i s/ssi-slave/ssi-peripheral/ $(git grep -l ssi-slave)
$ sed -i s/ssi_slave/ssi_peripheral/ $(git grep -l ssi_slave)
$ sed -i s/ssi_create_slave/ssi_create_peripheral/ \
$(git grep -l ssi_create_slave)
Then in VMStateDescription vmstate_ssi_peripheral we restored
the "SSISlave" migration stream name (to avoid breaking migration).
Finally the following files have been manually tweaked:
- hw/ssi/pl022.c
- hw/ssi/xilinx_spips.c
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* New device model for EMC1413/EMC1414 temperature sensors (I2C)
* New g220a-bmc Aspeed machine
* couple of Aspeed cleanups
-----BEGIN PGP SIGNATURE-----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=abAb
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20201210' into staging
Aspeed patches :
* New device model for EMC1413/EMC1414 temperature sensors (I2C)
* New g220a-bmc Aspeed machine
* couple of Aspeed cleanups
# gpg: Signature made Thu 10 Dec 2020 11:58:10 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20201210:
aspeed: g220a-bmc: Add an FRU
aspeed/smc: Add support for address lane disablement
ast2600: SRAM is 89KB
aspeed: Add support for the g220a-bmc board
hw/misc: add an EMC141{3,4} device model
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-5-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-4-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-3-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-2-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Largely inspired by the TMP421 temperature sensor, here is a model for
the EMC1413/EMC1414 temperature sensors.
Specs can be found here :
http://ww1.microchip.com/downloads/en/DeviceDoc/20005274A.pdf
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201122105134.671-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This way we can tell between regular IOMMUTLBEntry (entry of IOMMU
hardware) and notifications.
In the notifications, we set explicitly if it is a MAPs or an UNMAP,
instead of trusting in entry permissions to differentiate them.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The TMP105 datasheet says that in Interrupt Mode (when TM==1) the device
signals an alert when the temperature equals or exceeds the T_high value and
then remains high until a device register is read or the device responds to
the SMBUS Alert Response address, or the device is put into Shutdown Mode.
Thereafter the Alert pin will only be re-signalled when temperature falls
below T_low; alert can then be cleared in the same set of ways, and the
device returns to its initial "alert when temperature goes above T_high"
mode. (If this textual description is confusing, see figure 3 in the
TI datasheet at https://www.ti.com/lit/gpn/tmp105 .)
We were misimplementing this as a simple "always alert if temperature is
above T_high or below T_low" condition, which gives a spurious alert on
startup if using the "T_high = 80 degrees C, T_low = 75 degrees C" reset
limit values.
Implement the correct (hysteresis) behaviour by tracking whether we
are currently looking for the temperature to rise over T_high or
for it to fall below T_low. Our implementation of the comparator
mode (TM==0) wasn't wrong, but rephrase it to match the way that
interrupt mode is now handled for clarity.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20201110150023.25533-3-peter.maydell@linaro.org
The TMP105 datasheet (https://www.ti.com/lit/gpn/tmp105) says that the
power-up reset values for the T_low and T_high registers are 80 degrees C
and 75 degrees C, which are 0x500 and 0x4B0 hex according to table 5. These
values are then shifted right by four bits to give the register reset
values, since both registers store the 12 bits of temperature data in bits
[15..4] of a 16 bit register.
We were resetting these registers to zero, which is problematic for Linux
guests which enable the alert interrupt and then immediately take an
unexpected overtemperature alert because the current temperature is above
freezing...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20201110150023.25533-2-peter.maydell@linaro.org
The category of the max111x device is not set, put it into the 'misc'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201112125824.763182-5-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Commit 348b8d1a76 "macio: don't reference serial_hd() directly within the device"
removed the setting of user_creatable to false on the basis that the restriction
was due to the use of serial_hd() in macio_instance_init().
Unfortunately this isn't the full story since the PIC object property links
must still be set before the device is realized. Whilst it is possible to update
the macio device and Mac machines to resolve this, the fix is too invasive at
this point in the release cycle.
For now simply set user_creatable back to false in macio_class_init() to
prevent QEMU from segfaulting in anticipation of the proper fix arriving in
QEMU 6.0.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201110103111.18395-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Advertise both types of events as supported when the guest OS
queries the pvpanic device. Currently only PVPANIC_PANICKED is
exposed; PVPANIC_CRASHLOADED must also be advertised, but only on
new machine types.
Fixes: 7dc58deea7 ("pvpanic: implement crashloaded event handling")
Reported-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The system configuration controller (SYSCFG) doesn't have
any output IRQ (and the INTC input #71 belongs to the UART6).
Remove the invalid code.
Fixes: db635521a0 ("stm32f205: Add the stm32f205 SoC")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
