QEMU does not allocate PCI resources (BARs) in any case - coldplug devices
are configured by the firmware and hotplug devices rely on the guest
system to do the assignment via the PCI rescan mechanism. Also in order
to create non empty "assigned-addresses", the device has to be enabled
(i.e. PCI_COMMAND needs the MMIO bit set) first as otherwise
io_regions[i].addr are -1, and devices are not enabled at this point.
This removes "assigned-addresses" and leaves it to those who actually
do resource allocation.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190927022651.71642-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SLOF implements one itself so let's remove it from QEMU. It is one less
image and simpler setup as the RTAS blob never stays in its initial place
anyway as the guest OS always decides where to put it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We are going to use spapr_build_fdt() for the boot time FDT and as an
update for SLOF during handling of H_CAS. SLOF will apply all properties
from the QEMU's FDT which is usually ok unless there are properties
changed by grub or guest kernel. The properties are:
bootargs, linux,initrd-start, linux,initrd-end, linux,stdout-path,
linux,rtas-base, linux,rtas-entry. Resetting those during CAS will most
likely cause grub failure.
Don't create such properties if we're booting without "-kernel" and
"-initrd" so they won't get included into the DT update blob and
therefore the guest is more likely to boot successfully.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[dwg: Tweaked commit message based on Greg Kurz's input]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The device tree build by QEMU at the machine reset time is used by SLOF
to build its internal device tree but the node names are not preserved
exactly so when QEMU provides a device tree update in response to H_CAS,
it might become tricky to match a node from the update blob to
the actual node in SLOF.
This removed leading zeroes from "memory@" nodes and makes
the DTC checker happy.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Add a missing g_free(fdt) if the resulting tree is bigger
than the space allocated by SLOF.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The number of NUMA nodes in the system is fixed from the command line.
Therefore, there's no need to recalculate it at reset time, and we can
determine the special gpu_numa_id value used for NVLink2 devices at init
time.
This simplifies the reset path a bit which will make further improvements
easier.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Certain old guest versions don't understand the radix MMU introduced with
POWER ISA 3.0, but incorrectly select it if presented with the option at
CAS time. We workaround this in qemu by explicitly excluding the radix
(and other ISA 3.0 linked) options if the guest doesn't explicitly note
support for ISA 3.0.
This is handled by the 'cas_legacy_guest_workaround' flag, which is pretty
vague. Rename it to 'cas_pre_isa3_guest' to be clearer about what it's for.
In addition, we unnecessarily call spapr_populate_pa_features() with
different options when initially constructing the device tree and when
adjusting it at CAS time. At the initial construct time cas_pre_isa3_guest
is already false, so we can still use the flag, rather than explicitly
overriding it to be false at the callsite.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
It will help us to discard interrupt numbers which have not been
claimed in the next patch.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190911133937.2716-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
add PnvHomer device model to emulate homer memory access
for pstate table, occ-sensors, slw, occ static and dynamic
values for Power8 and Power9 chips.
Signed-off-by: Balamuruhan S <bala24@linux.ibm.com>
Message-Id: <20190912093056.4516-4-bala24@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
emulate occ common area region with occ sram device model which
occ and skiboot uses it to communicate regarding sensors, slw
and HWMON in PowerNV emulated host.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Balamuruhan S <bala24@linux.ibm.com>
Message-Id: <20190912093056.4516-3-bala24@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
During PowerNV boot skiboot populates the device tree by
retrieving base address of homer/occ common area from
PBA BARs and prd ipoll mask by accessing xscom read/write
accesses.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Balamuruhan S <bala24@linux.ibm.com>
Message-Id: <20190912093056.4516-2-bala24@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Unless the machine was started with kernel-irqchip=on, we cannot easily
tell if we're actually using an in-kernel or an emulated irqchip. This
information is important enough that it is worth printing it in 'info
pic'.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156829860985.2073005.5893493824873412773.stgit@bahia.tls.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There were few trailing comments after `/*` instead in
new line and line more than 80 character, these fixes are
trivial and doesn't change any logic in code.
Signed-off-by: Balamuruhan S <bala24@linux.ibm.com>
Message-Id: <20190911142925.19197-5-bala24@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Coverity is reporting in CID 1405304 that tpm_execute() may pass a NULL
tpm_proxy->host_path pointer to open(). This is based on the fact that
h_tpm_comm() does a NULL check on tpm_proxy->host_path and then passes
tpm_proxy to tpm_execute().
The check in h_tpm_comm() is abusive actually since a spapr-proxy-tpm
requires a non NULL host_path property, as checked during realize.
Fixes: 0fb6bd0732
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156805260916.1779401.11054185183758185247.stgit@bahia.lan>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fixes the dtc output :
ERROR (node_name_chars): //bmc: Bad character '/' in node name
Warning (avoid_unnecessary_addr_size): /bmc: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190902092932.20200-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When we hotplug a CPU on memory-less/cpu-less node, the linux kernel
crashes.
This happens because linux kernel needs to know the NUMA topology at
start to be able to initialize the distance lookup table.
On pseries, the topology is provided by the firmware via the existing
CPUs and memory information. Thus a node without memory and CPU cannot be
discovered by the kernel.
To avoid the kernel crash, do not allow to start pseries with empty
nodes.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20190830161345.22436-1-lvivier@redhat.com>
[dwg: Rework to cope with movement of numa state from globals to MachineState]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 78dd48df3 removed the last caller of register_savevm_live for an
instantiable device (rather than a single system wide device);
so trim out the parameter.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190822115433.12070-1-dgilbert@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Bug fixes:
* Fix die-id validation regression (Eduardo Habkost)
* vmmouse: Properly reset state (Jan Kiszka)
* hostmem-file: fix pmem file size check (Stefan Hajnoczi)
* Keep query-hotpluggable-cpus output compatible with older QEMU
if '-smp dies' is not set (Igor Mammedov)
* migration: Do not re-read the clock on pre_save in case of paused guest
(Maxiwell S. Garcia)
Cleanups:
* NUMA code cleanups (Tao Xu)
* Remove stale externs from includes (Alex Bennée)
Features:
* qapi: report the default CPU type for each machine (Daniel P. Berrangé)
-----BEGIN PGP SIGNATURE-----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=u5HZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/machine-next-pull-request' into staging
Machine + x86 queue, 2019-09-03
Bug fixes:
* Fix die-id validation regression (Eduardo Habkost)
* vmmouse: Properly reset state (Jan Kiszka)
* hostmem-file: fix pmem file size check (Stefan Hajnoczi)
* Keep query-hotpluggable-cpus output compatible with older QEMU
if '-smp dies' is not set (Igor Mammedov)
* migration: Do not re-read the clock on pre_save in case of paused guest
(Maxiwell S. Garcia)
Cleanups:
* NUMA code cleanups (Tao Xu)
* Remove stale externs from includes (Alex Bennée)
Features:
* qapi: report the default CPU type for each machine (Daniel P. Berrangé)
# gpg: Signature made Tue 03 Sep 2019 21:57:37 BST
# gpg: using RSA key 5A322FD5ABC4D3DBACCFD1AA2807936F984DC5A6
# gpg: issuer "ehabkost@redhat.com"
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>" [full]
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/machine-next-pull-request:
migration: Do not re-read the clock on pre_save in case of paused guest
x86: do not advertise die-id in query-hotpluggbale-cpus if '-smp dies' is not set
i386/vmmouse: Properly reset state
hostmem-file: fix pmem file size check
qapi: report the default CPU type for each machine
pc: Don't make die-id mandatory unless necessary
pc: Improve error message when die-id is omitted
pc: Fix error message on die-id validation
numa: move numa global variable numa_info into MachineState
numa: move numa global variable have_numa_distance into MachineState
numa: move numa global variable nb_numa_nodes into MachineState
hw/arm: simplify arm_load_dtb
includes: remove stale [smp|max]_cpus externs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move existing numa global numa_info (renamed as "nodes") into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-5-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add struct NumaState in MachineState and move existing numa global
nb_numa_nodes(renamed as "num_nodes") into NumaState. And add variable
numa_support into MachineClass to decide which submachines support NUMA.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-3-tao3.xu@intel.com>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
A recent change in spapr_machine_reset() showed that resetting the compat
mode in spapr_machine_reset() for the boot vCPU and in spapr_cpu_reset()
for all other vCPUs was fragile. The fix was thus to reset the compat mode
for all vCPUs in spapr_machine_reset(), but we still have to propagate
it to hot-plugged CPUs. This is still performed from spapr_cpu_reset(),
hence resulting in ppc_set_compat() being called twice for every vCPU at
machine reset. Apart from wasting cycles, which isn't really an issue
during machine reset, this seems to indicate that spapr_cpu_reset() isn't
the best place to set the compat mode.
A natural candidate for CPU-hotplug specific code is spapr_core_plug().
Also, it sits in the same file as spapr_machine_reset() : this makes
it easier for someone who wants to know when the compat PVR is set.
Call ppc_set_compat() from there. This doesn't need to be done for
initial vCPUs since the compat PVR is 0 and spapr_machine_reset() sets
the appropriate value later. No need to do this on manually added vCPUS
on the destination QEMU during migration since the compat PVR is
part of the migrated vCPU state. Both conditions can be checked with
spapr_drc_hotplugged().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156701285312.499757.7807417667750711711.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The QEMU coding style requires:
- to typedef structured types (HACKING)
- to use CamelCase for types and structure names (CODING_STYLE)
Do that for PCI and Nvlink2 code.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156701644465.505236.2850655823182656869.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries guests do not normally allocate PCI resources and rely on
the system firmware doing so. Furthermore at least at some point in
the past the pseries guests won't even allowed to change BARs, probably
it is still the case for phyp. So since the initial commit we have [1]
which prevents resource reallocation.
This is not a problem until we want specific BAR alignments, for example,
PAGE_SIZE==64k to make sure we can still map MMIO BARs directly. For
the boot time devices we handle this in SLOF [2] but since QEMU's RTAS
does not allocate BARs, the guest does this instead and does not align
BARs even if Linux is given pci=resource_alignment=16@pci:0:0 as
PCI_PROBE_ONLY makes Linux ignore alignment requests.
ARM folks added a dial to control PCI_PROBE_ONLY via the device tree [3].
This makes use of the dial to advertise to the guest that we can handle
BAR reassignments. This limits the change to the latest pseries machine
to avoid old guests explosion.
We do not remove the flag from [1] as pseries guests are still supported
under phyp so having that removed may cause problems.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/powerpc/platforms/pseries/setup.c?h=v5.1#n773
[2] https://git.qemu.org/?p=SLOF.git;a=blob;f=board-qemu/slof/pci-phb.fs;h=06729bcf77a0d4e900c527adcd9befe2a269f65d;hb=HEAD#l338
[3] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=f81c11af
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190719043734.108462-1-aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sPAPR platform includes feature negotiation between the guest and
platform. That sometimes requires reconfiguring the virtual hardware, and
in some cases that is a complex enough process that we trigger a system
reset to handle it. That interacts badly with -no-reboot - we trigger the
reboot, -no-reboot means we exit and so the guest never gets to try again.
Eventually we want to get rid of CAS reboots entirely, since they're odd
and irritating for the user. But in the meantime we can fix the -no-reboot
problem by using SHUTDOWN_CAUSE_SUBSYSTEM_RESET which ignores -no-reboot
and seems to be designed for this sort of faux-reset for internal purposes
only.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ibm,get_system_parameter rtas call is used by the guest to retrieve
data relating to certain parameters of the system. The SPLPAR
characteristics option (token 20) is used to determine characteristics of
the environment in which the lpar will run.
It may be useful for a guest to know the number of physical host threads
present on the underlying system where it is being run. Add the
characteristic "HostThrs" to the SPLPAR Characteristics
ibm,get_system_parameter rtas call to expose this information to a
guest. Add a n_host_threads property to the processor class which is
then used to retrieve this information and define it for POWER8 and
POWER9. Other processors will default to 0 and the charateristic won't
be added.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190827045751.22123-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If we a migrate P8 machine to a P9 machine, the migration fails on
destination with:
error while loading state for instance 0x1 of device 'cpu'
load of migration failed: Operation not permitted
This is caused because the compat_pvr field is only present for the first
CPU.
Originally, spapr_machine_reset() calls ppc_set_compat() to set the value
max_compat_pvr for the first cpu and this was propagated to all CPUs by
spapr_cpu_reset(). Now, as spapr_cpu_reset() is called before that, the
value is not propagated to all CPUs and the migration fails.
To fix that, propagate the new value to all CPUs in spapr_machine_reset().
Fixes: 25c9780d38 ("spapr: Reset CAS & IRQ subsystem after devices")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20190826090812.19080-1-lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is nothing wrong with how sPAPR handles multifunction PCI
hot unplugs. The problem is that x86 does it simpler. Instead of
removing each non-zero function and then removing function zero,
x86 can remove any function of the slot to trigger the hot unplug.
Libvirt will be directly impacted by this difference, in the
(hopefully soon) PCI Multifunction hot plug/unplug support. For
hot plugs, both x86 and sPAPR will operate the same way: a XML
with all desired functions to be added, then consecutive hotplugs
of all non-zero functions first, zero last. For hot unplugs, at
least in the current state, a XML with the devices to be removed
must also be provided because of how sPAPR operates - x86 does
not need it - since any function unplug will unplug the whole
PCIe slot. This difference puts extra strain in the management
layer, which needs to either handle both archs differently in
the unplug scenario or choose treat x86 like sPAPR, forcing x86
users to cope with sPAPR internals.
This patch changes spapr_pci_unplug_request to handle the
unplug of function zero differently. When removing function zero,
instead of error-ing out if there are any remaining function
DRCs which needs detaching, detach those. This has no effect in
any existing scripts that are detaching the non-zero functions
before function zero, and can be used by management as a shortcut
to remove the whole PCI multifunction device without specifying
each child function.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20190822195918.3307-1-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Make the current "powernv" machine an abstract type and derive from it
new machines with specific CPU models: power8 and power9.
The "powernv" machine is now an alias on the "powernv9" machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190731141233.1340-2-clg@kaod.org>
[dwg: Adjust pnv-xscom-test to cope with this change]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Devices such as the BT or serial devices require a valid
"interrupt-parent" phandle in the device tree and it is currently
empty (0x0). It was not a problem until now but since OpenFirmare
started using a recent libdft (>= 1.4.7), petitboot fails to boot the
system image with error :
dtc_resize: fdt_open_into returned FDT_ERR_BADMAGIC
Provide a phandle for the LPC bus.
Suggested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190723090138.30623-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes the powernv machine easier for end users as the default
initrd address (1.5GB) is now within RAM.
This uses less than 2GB of RAM to ensure 32 bit Qemu still works.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20190821030945.473-1-joel@jms.id.au>
[dwg: Fix comment style for checkpatch]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
GCC9 is confused by this comment when building with CFLAG
-Wimplicit-fallthrough=2:
CC ppc64-softmmu/hw/ppc/spapr_rtc.o
hw/ppc/spapr_events.c: In function ‘rtas_event_log_to_source’:
hw/ppc/spapr_events.c:312:12: error: this statement may fall through [-Werror=implicit-fallthrough=]
312 | if (spapr_ovec_test(spapr->ov5_cas, OV5_HP_EVT)) {
| ^
hw/ppc/spapr_events.c:317:5: note: here
317 | case RTAS_LOG_TYPE_EPOW:
| ^~~~
cc1: all warnings being treated as errors
Rewrite the comment using 'fall through' which is recognized by
GCC and static analyzers.
Reported-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190719131425.10835-8-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
PHBs already take care of clearing the MSIs from the bitmap during reset
or unplug. No need to do this globally from the machine code. Rather add
an assert to ensure that PHBs have acted as expected.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156415228966.1064338.190189424190233355.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix crash in qtest case where spapr->irq_map can be NULL at the
new assert()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the machine is reset, the MSI bitmap is cleared but the allocated
MSIs are not freed. Some operating systems, such as AIX, can detect the
previous configuration and assert.
Empty the MSI cache, this performs the needed cleanup.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156415228410.1064338.4486161194061636096.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When freeing MSIs, we need to:
- remove them from the machine's MSI bitmap
- remove them from the IC backend
- remove them from the PHB's MSI cache
This is currently open coded in two places in rtas_ibm_change_msi(),
and we're about to need this in spapr_phb_reset() as well. Instead of
duplicating this code again, make it a destroy function for the PHB's
MSI cache. Removing an MSI device from the cache will call the destroy
function internally.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156415227855.1064338.5657793835271464648.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This has been useful to modify and test the Linux pseries suspend
code but it requires modification to the guest to call it (due to
being gated by other unimplemented features). It is not otherwise
used by Linux yet, but work is slowly progressing there.
This allows a (lightly modified) guest kernel to suspend with
`echo mem > /sys/power/state` and be resumed with system_wakeup
monitor command.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190722061752.22114-2-npiggin@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This implements the H_TPM_COMM hypercall, which is used by an
Ultravisor to pass TPM commands directly to the host's TPM device, or
a TPM Resource Manager associated with the device.
This also introduces a new virtual device, spapr-tpm-proxy, which
is used to configure the host TPM path to be used to service
requests sent by H_TPM_COMM hcalls, for example:
-device spapr-tpm-proxy,id=tpmp0,host-path=/dev/tpmrm0
By default, no spapr-tpm-proxy will be created, and hcalls will return
H_FUNCTION.
The full specification for this hypercall can be found in
docs/specs/ppc-spapr-uv-hcalls.txt
Since SVM-related hcalls like H_TPM_COMM use a reserved range of
0xEF00-0xEF80, we introduce a separate hcall table here to handle
them.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com
Message-Id: <20190717205842.17827-3-mdroth@linux.vnet.ibm.com>
[dwg: Corrected #include for upstream change]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This has been useful to modify and test the Linux pseries suspend
code but it requires modification to the guest to call it (due to
being gated by other unimplemented features). It is not otherwise
used by Linux yet, but work is slowly progressing there.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-5-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This does not do directed yielding and is not quite as strict as PAPR
specifies in terms of precise dispatch behaviour. This generally will
mean suboptimal performance, rather than guest misbehaviour. Linux
does not rely on exact dispatch behaviour.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-4-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
H_PROD is added, and H_CEDE is modified to test the prod bit
according to PAPR.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-3-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Implement cpu_exec_enter/exit on ppc which calls into new methods of
the same name in PPCVirtualHypervisorClass. These are used by spapr
to implement the splpar VPA dispatch counter initially.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-2-npiggin@gmail.com>
[dwg: Removed unnecessary CONFIG_USER_ONLY checks as suggested by gkurz]
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Free all SpaprOptionVector local pointers after use.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Message-Id: <156335160761.82682.11912058325777251614.stgit@lep8c.aus.stglabs.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Leaking the drc_name while preparing the DT properties.
Fixing that.
Also, remove the const qualifier from spapr_drc_name().
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Message-Id: <156335159028.82682.5404622104535818162.stgit@lep8c.aus.stglabs.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Free the capability name string after setting
the capability.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Message-Id: <156335156198.82682.8756968724044750843.stgit@lep8c.aus.stglabs.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Re-read the timebase before migrate was ported from x86 commit:
6053a86fe7: kvmclock: reduce kvmclock difference on migration
The clock move makes the guest knows about the paused time between
the stop and migrate commands. This is an issue in an already-paused
VM because some side effects, like process stalls, could happen
after migration.
So, this patch checks the runstate of guest in the pre_save handler and
do not re-reads the timebase in case of paused state (cold migration).
Signed-off-by: Maxiwell S. Garcia <maxiwell@linux.ibm.com>
Message-Id: <20190711194702.26598-1-maxiwell@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We've had the qemu and kernel KVM infrastructure to handle larger TCE
page sizes for a while, but forgot to update the defaults to actually
allow them. This turns that change on.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add 4.2 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1, as 0788a56bd1 ("i386: Make unversioned CPU models be
aliases") states this should only transition to the latest cpu
model version in 4.3 (or later).
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190724103524.20916-1-cohuck@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
