This virtual method was always set to the x86-specific pc_madt_cpu_entry(),
even in piix4 which is also used in MIPS. The previous changes use
pc_madt_cpu_entry() otherwise, so madt_cpu can be dropped.
Since pc_madt_cpu_entry() is now only used in x86-specific code, the stub
in hw/acpi/acpi-x86-stub can be removed as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
build_cpus_aml() is architecture independent but needs to create architecture-
specific CPU AML. So far this was achieved by using a virtual method from
TYPE_ACPI_DEVICE_IF. However, build_cpus_aml() would resolve this interface from
global (!) state. This makes it quite incomprehensible where this interface
comes from (TYPE_PIIX4_PM?, TYPE_ICH9_LPC_DEVICE?, TYPE_ACPI_GED_X86?) an can
lead to crashes when the generic code is ported to new architectures.
So far, build_cpus_aml() is only called in architecture-specific code -- and
only in x86. We can therefore simply pass pc_madt_cpu_entry() as callback to
build_cpus_aml(). This is the same callback that would be used through
TYPE_ACPI_DEVICE_IF.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is x86-specific code, so there is no advantage in using
pc_madt_cpu_entry() behind an architecture-agnostic interface.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- The comment is incorrectly indented / formatted.
- The comment states a 8MB limit, even though the code enforces a 16MB
limit.
Both of these warts come from commit 0657c657eb ("hw/i386/pc: add max
combined fw size as machine configuration option", 2020-12-09); clean them
up.
Arguably, it's also better to be consistent with the binary units (such as
"MiB") that QEMU uses nowadays.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:PC)
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com> (supporter:PC)
Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86 TCG CPUs)
Cc: Richard Henderson <richard.henderson@linaro.org> (maintainer:X86 TCG CPUs)
Cc: Eduardo Habkost <eduardo@habkost.net> (maintainer:X86 TCG CPUs)
Cc: qemu-trivial@nongnu.org
Fixes: 0657c657eb
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It's weird to shift x & y without obvious reason. Let's make this more
explicit and future-proof.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
* target/i386: fix BQL handling of the legacy FERR interrupts
* target/i386: fix memory operand size for CVTPS2PD
* target/i386: Add support for AMX-COMPLEX in CPUID enumeration
* compile plugins on Darwin
* configure and meson cleanups
* drop mkvenv support for Python 3.7 and Debian10
* add wrap file for libblkio
* tweak KVM stubs
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmT5t6UUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMmjwf+MpvVuq+nn+3PqGUXgnzJx5ccA5ne
O9Xy8+1GdlQPzBw/tPovxXDSKn3HQtBfxObn2CCE1tu/4uHWpBA1Vksn++NHdUf2
P0yoHxGskJu5iYYTtIcNw5cH2i+AizdiXuEjhfNjqD5Y234cFoHnUApt9e3zBvVO
cwGD7WpPuSb4g38hHkV6nKcx72o7b4ejDToqUVZJ2N+RkddSqB03fSdrOru0hR7x
V+lay0DYdFszNDFm05LJzfDbcrHuSryGA91wtty7Fzj6QhR/HBHQCUZJxMB5PI7F
Zy4Zdpu60zxtSxUqeKgIi7UhNFgMcax2Hf9QEqdc/B4ARoBbboh4q4u8kQ==
=dH7/
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* only build util/async-teardown.c when system build is requested
* target/i386: fix BQL handling of the legacy FERR interrupts
* target/i386: fix memory operand size for CVTPS2PD
* target/i386: Add support for AMX-COMPLEX in CPUID enumeration
* compile plugins on Darwin
* configure and meson cleanups
* drop mkvenv support for Python 3.7 and Debian10
* add wrap file for libblkio
* tweak KVM stubs
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmT5t6UUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroMmjwf+MpvVuq+nn+3PqGUXgnzJx5ccA5ne
# O9Xy8+1GdlQPzBw/tPovxXDSKn3HQtBfxObn2CCE1tu/4uHWpBA1Vksn++NHdUf2
# P0yoHxGskJu5iYYTtIcNw5cH2i+AizdiXuEjhfNjqD5Y234cFoHnUApt9e3zBvVO
# cwGD7WpPuSb4g38hHkV6nKcx72o7b4ejDToqUVZJ2N+RkddSqB03fSdrOru0hR7x
# V+lay0DYdFszNDFm05LJzfDbcrHuSryGA91wtty7Fzj6QhR/HBHQCUZJxMB5PI7F
# Zy4Zdpu60zxtSxUqeKgIi7UhNFgMcax2Hf9QEqdc/B4ARoBbboh4q4u8kQ==
# =dH7/
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 07 Sep 2023 07:44:37 EDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (51 commits)
docs/system/replay: do not show removed command line option
subprojects: add wrap file for libblkio
sysemu/kvm: Restrict kvm_pc_setup_irq_routing() to x86 targets
sysemu/kvm: Restrict kvm_has_pit_state2() to x86 targets
sysemu/kvm: Restrict kvm_get_apic_state() to x86 targets
sysemu/kvm: Restrict kvm_arch_get_supported_cpuid/msr() to x86 targets
target/i386: Restrict declarations specific to CONFIG_KVM
target/i386: Allow elision of kvm_hv_vpindex_settable()
target/i386: Allow elision of kvm_enable_x2apic()
target/i386: Remove unused KVM stubs
target/i386/cpu-sysemu: Inline kvm_apic_in_kernel()
target/i386/helper: Restrict KVM declarations to system emulation
hw/i386/fw_cfg: Include missing 'cpu.h' header
hw/i386/pc: Include missing 'cpu.h' header
hw/i386/pc: Include missing 'sysemu/tcg.h' header
Revert "mkvenv: work around broken pip installations on Debian 10"
mkvenv: assume presence of importlib.metadata
Python: Drop support for Python 3.7
configure: remove dead code
meson: list leftover CONFIG_* symbols
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
kvm_pc_setup_irq_routing() is only defined for x86 targets (in
hw/i386/kvm/apic.c). Its declaration is pointless on all
other targets.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-14-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_has_pit_state2() is only defined for x86 targets (in
target/i386/kvm/kvm.c). Its declaration is pointless on
all other targets. Have it return a boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-13-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_enabled() before kvm_hv_vpindex_settable()
to let the compiler elide its call.
kvm-stub.c is now empty, remove it.
Suggested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-9-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_enabled() before kvm_enable_x2apic() to let the compiler elide
its call. Cleanup the code by simplifying "!xen_enabled() &&
kvm_enabled()" to just "kvm_enabled()".
Suggested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-8-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
fw_cfg_build_feature_control() uses CPUID_EXT_VMX which is
defined in "target/i386/cpu.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-4-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both pc_piix.c and pc_q35.c files use CPU_VERSION_LEGACY
which is defined in "target/i386/cpu.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-3-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 6f529b7534 ("target/i386: move FERR handling
to target/i386") pc_q35_init() calls tcg_enabled() which
is declared in "sysemu/tcg.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-2-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvmclock_create() is only implemented in hw/i386/kvm/clock.h.
Restrict the "hw/kvm/clock.h" header to i386 by moving it to
hw/i386/.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230620083228.88796-3-philmd@linaro.org>
We shouldn't call kvmclock_create() when KVM is not available
or disabled:
- check for kvm_enabled() before calling it
- assert KVM is enabled once called
Since the call is elided when KVM is not available, we can
remove the stub (it is never compiled).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230620083228.88796-2-philmd@linaro.org>
The buttons value use macros instead of direct numbers.
If request relative mode, have to add this for
guest vmmouse driver to judge this is a relative packet.
otherwise,vmmouse driver will not match
the condition 'status & VMMOUSE_RELATIVE_PACKET',
and can't report events on the correct(relative) input device,
result to relative mode unuseful.
Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Message-ID: <20230413081526.2229916-1-zhouzongmin@kylinos.cn>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
The values in "msg" are assembled in host endian byte order (the other
field are also not swapped), so we must not swap the __addr_head here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-6-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
The values in "addr" are populated locally in this function in host
endian byte order, so we must not swap the index_l field here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-5-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
On big endian hosts, we need to reverse the bitfield order in the
struct VTDInvDescIEC, just like it is already done for the other
bitfields in the various structs of the intel-iommu device.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-4-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The code already tries to do some endianness handling here, but
currently fails badly:
- While it already swaps the data when logging errors / tracing, it fails
to byteswap the value before e.g. accessing entry->irte.present
- entry->irte.source_id is swapped with le32_to_cpu(), though this is
a 16-bit value
- The whole union is apparently supposed to be swapped via the 64-bit
data[2] array, but the struct is a mixture between 32 bit values
(the first 8 bytes) and 64 bit values (the second 8 bytes), so this
cannot work as expected.
Fix it by converting the struct to two proper 64-bit bitfields, and
by swapping the values only once for everybody right after reading
the data from memory.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-3-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
After reading the guest memory with dma_memory_read(), we have
to make sure that we byteswap the little endian data to the host's
byte order.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-2-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
ACPI spec (since 2.0a) says
"
A device object must contain either an _HID object or
an _ADR object, but can contain both.
"
_ADR is used when device is attached to an ennumerable bus,
however hostbridge is not and uses dedicated _HID for
discovery, drop _ADR field.
It doesn't seem that having _ADR has a negative effects
OSes manage to tolerate that, but there is no point of
having it there. (only pc/q35 has it hostbridge description,
while others (microvm/arm) don't)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230720133858.1974024-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it seems that Windows is unable to handle variable references
making it choke up when accessing ASUN during _DSM call
when device is hotplugged (it lists package elements as DataAlias
but despite that later on it misbehaves) with following error
shown up in AMLI debugger (WS2012r2):
Store(ShiftLeft(One,Arg1="ASUN",) AMLI_ERROR(c0140008): Unexpected argument type
ValidateArgTypes: expected Arg1 to be type Integer (Type=String)
Similar outcome with WS2022.
Issue is not fatal but as result acpi-index/"PCI Label ID" property
is either not shown in device details page or shows incorrect value.
Fix it by doing assignment of BSEL/ASUN values to package
elements manually after package declaration.
Fix was tested with: WS2012r2, WS2022, RHEL9
Fixes: 467d099a29 (x86: acpi: _DSM: use Package to pass parameters)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230720133858.1974024-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fuzzing showed that a guest could bind an interdomain port to itself, by
guessing the next port to be allocated and putting that as the 'remote'
port number. By chance, that works because the newly-allocated port has
type EVTCHNSTAT_unbound. It shouldn't.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20230801175747.145906-4-dwmw2@infradead.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Coverity points out (CID 1508128) a bounds checking error. We need to check
for gsi >= IOAPIC_NUM_PINS, not just greater-than.
Also fix up an assert() that has the same problem, that Coverity didn't see.
Fixes: 4f81baa33e ("hw/xen: Support GSI mapping to PIRQ")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230801175747.145906-2-dwmw2@infradead.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The IDE unplug function needs to reset the entire PCI device, to make
sure all state is initialized to defaults. This is done by calling
pci_device_reset, which resets not only the chip specific registers, but
also all PCI state. This fixes "unplug" in a Xen HVM domU with the
modular legacy xenlinux PV drivers.
Commit ee358e919e ("hw/ide/piix: Convert reset handler to
DeviceReset") changed the way how the the disks are unplugged. Prior
this commit the PCI device remained unchanged. After this change,
piix_ide_reset is exercised after the "unplug" command, which was not
the case prior that commit. This function resets the command register.
As a result the ata_piix driver inside the domU will see a disabled PCI
device. The generic PCI code will reenable the PCI device. On the qemu
side, this runs pci_default_write_config/pci_update_mappings. Here a
changed address is returned by pci_bar_address, this is the address
which was truncated in piix_ide_reset. In case of a Xen HVM domU, the
address changes from 0xc120 to 0xc100. This truncation was a bug in
piix_ide_reset, which was fixed in commit 230dfd9257 ("hw/ide/piix:
properly initialize the BMIBA register"). If pci_xen_ide_unplug had used
pci_device_reset, the PCI registers would have been properly reset, and
commit ee358e919e would have not introduced a regression for this
specific domU environment.
While the unplug is supposed to hide the IDE disks, the changed BMIBA
address broke the UHCI device. In case the domU has an USB tablet
configured, to recive absolute pointer coordinates for the GUI, it will
cause a hang during device discovery of the partly discovered USB hid
device. Reading the USBSTS word size register will fail. The access ends
up in the QEMU piix-bmdma device, instead of the expected uhci device.
Here a byte size request is expected, and a value of ~0 is returned. As
a result the UCHI driver sees an error state in the register, and turns
off the UHCI controller.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20230720072950.20198-1-olaf@aepfle.de>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Coverity points out (CID 1513106, 1513107) that MemoryListener is a
192 byte struct which we are passing around by value. Switch to
passing a const pointer into xen_register_ioreq() and then to
xen_do_ioreq_register(). We can also make the file-scope
MemoryListener variables const, since nothing changes them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230718101057.1110979-1-peter.maydell@linaro.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Coverity was unhappy (CID 1508359) because we didn't check the return of
init_walk_op() in transaction_commit(), despite doing so at every other
call site.
Strictly speaking, this is a false positive since it can never fail. It
only fails for invalid user input (transaction ID or path), and both of
those are hard-coded to known sane values in this invocation.
But Coverity doesn't know that, and neither does the casual reader of the
code.
Returning an error here would be weird, since the transaction *is*
committed by this point; all the walk_op is doing is firing watches on
the newly-committed changed nodes. So make it a g_assert(!ret), since
it really should never happen.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20076888f6bdf06a65aafc5cf954260965d45b97.camel@infradead.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Let's factor out (un)plug handling, to be reused from arm/virt code.
Provide stubs for the case that CONFIG_VIRTIO_MD is not selected because
neither virtio-mem nor virtio-pmem is enabled. While this cannot
currently happen for x86, it will be possible for arm/virt.
Message-ID: <20230711153445.514112-3-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
There are no remaining users in the tree. Libvirt never used that
property and a quick internet search revealed no other users.
Further, we renamed that property already in commit f2ffbe2b7d
("pc: rename "hotplug memory" terminology to "device memory"") without
anybody complaining.
So let's just get rid of it.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-9-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We're already looking at machine->device_memory when calling
build_srat_memory(), so let's simply avoid going via
PC_MACHINE_DEVMEM_REGION_SIZE to get the size and rely on
machine->device_memory directly.
Once machine->device_memory is set, we know that the size > 0. The code now
looks much more similar the hw/arm/virt-acpi-build.c variant.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-8-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's use our new helper and stop always allocating ms->device_memory.
Once allcoated, we're sure that the size > 0 and that the base was
initialized.
Adjust the code in pc_memory_init() to check for machine->device_memory
instead of pcmc->has_reserved_memory and machine->device_memory->base.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-7-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
There is also pci_new() which creates non-multifunction PCI devices.
Accordingly the parameter is always set to true when a multi function PCI
device is to be created.
The reason for the parameter's existence seems to be that it is used in the
internal PCI code as well which is the only location where it gets set to
false. This one usage can be resolved by factoring out an internal helper
function.
Remove this redundant, error-prone parameter.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230304114043.121024-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is also pci_create_simple() which creates non-multifunction PCI
devices. Accordingly the parameter is always set to true when a multi
function PCI device is to be created.
The reason for the parameter's existence seems to be that it is used in the
internal PCI code as well which is the only location where it gets set to
false. This one usage can be replaced by trivial code.
Remove this redundant, error-prone parameter.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230304114043.121024-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I440FX realization is currently mixed with PIIX3 creation. Furthermore, it is
common practice to only set properties between a device's qdev_new() and
qdev_realize(). Clean up to resolve both issues.
Since I440FX spawns a PCI bus let's also move the pci_bus initialization there.
Note that when running `qemu-system-x86_64 -M pc -S` before and after this
patch, `info mtree` in the QEMU console doesn't show any differences except that
the ordering is different.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-18-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
i440fx_init() is a legacy init function. The previous patches worked towards
TYPE_I440FX_PCI_HOST_BRIDGE to be instantiated the QOM way. Do this now by
transforming the parameters passed to i440fx_init() into property assignments.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-17-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Introduce the properties in anticipation of QOM'ification; Q35 has the same
properties.
Note that we want to avoid a "ram size" property in the QOM interface since it
seems redundant to both properties introduced in this change. Thus the removal
of the ram_size parameter. We assume the invariant of both properties to sum up
to "ram size" which is already asserted in pc_memory_init(). Under Xen the
invariant seems to hold as well, so we now also check it there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-15-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The parent-child relation is usually established near a child's qdev_new(). For
i440fx this allows for reusing the machine parameter, thus avoiding
qdev_get_machine() which relies on a global variable.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-9-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Eliminates an else branch.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-8-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-7-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Q35 PCI host already has a PCI_HOST_BYPASS_IOMMU property. However, the
host initializes this property itself by accessing global machine state,
thereby assuming it to be a PC machine. Avoid this by having board code
set this property.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Q35 PCI host currently sets the PC machine's PCI bus attribute
through global state, thereby assuming the machine to be a PC machine.
The Q35 machine code already holds on to Q35's pci bus attribute, so can
easily set its own property while preserving encapsulation.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The variable is redundant to "phb" and is never used by its real type.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add MEMORY_LISTNER_PRIORITY_ACCEL for the symbolic value for the memory
listener to replace the hard-coded value 10 for accel.
No functional change intended.
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <feebe423becc6e2aa375f59f6abce9a85bc15abb.1687279702.git.isaku.yamahata@intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
During address space unmap, corresponding IOVA tree entries are
also removed. But DMAMap is set beyond notifier's scope by 1, so
in theory there is possibility to remove a continuous entry above
the notifier's scope but falling in adjacent notifier's scope.
There is no issue currently as no use cases allocate notifiers
continuously, but let's be robust.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20230615032626.314476-4-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Replay doesn't notify registered notifiers but the one passed
to it. So it's meaningless to check the registered notifier's
synthetic flag.
There is no issue currently as all replay use cases have MAP
flag set, but let's be robust.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20230615032626.314476-3-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
