The AST2600 SoC SMC controller is a SPI only controller now and has a
few extensions which we will need to take into account when SW
requires it. This is enough to support u-boot and Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AST2600 will use a different encoding for the addresses defined in the
Segment Register.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the missing checksum calculation on normal DMA transfer.
According to the datasheet this is how the SMC should behave.
Verified on AST1250 that the hardware matches the behaviour.
Signed-off-by: Christian Svensson <bluecmd@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Emulate read errors in the DMA Checksum Register for high frequencies
and optimistic settings of the Read Timing Compensation Register. This
will help in tuning the SPI timing calibration algorithm. Errors are
only injected when the property "inject_failure" is set to true as
suggested by Philippe.
The values below are those to expect from the first flash device of
the FMC controller of a palmetto-bmc machine.
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing calibration, the SPI clock rate in the CE0 Control Register
and the read delay cycles in the Read Timing Compensation Register are
set using bit[11:4] of the DMA Control Register.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190904070506.1052-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The FMC controller on the Aspeed SoCs support DMA to access the flash
modules. It can operate in a normal mode, to copy to or from the flash
module mapping window, or in a checksum calculation mode, to evaluate
the best clock settings for reads.
The model introduces two custom address spaces for DMAs: one for the
AHB window of the FMC flash devices and one for the DRAM. The latter
is populated using a "dram" link set from the machine with the RAM
container region.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-6-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Improve the naming of the different controller models to ease their
generation when initializing the SoC. The rename of the SMC types is
breaking migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-5-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Reading the RX_DATA register when the RX_FIFO is empty triggers
an abort. This can be easily reproduced:
$ qemu-system-arm -M emcraft-sf2 -monitor stdio -S
QEMU 4.0.50 monitor - type 'help' for more information
(qemu) x 0x40001010
Aborted (core dumped)
(gdb) bt
#1 0x00007f035874f895 in abort () at /lib64/libc.so.6
#2 0x00005628686591ff in fifo8_pop (fifo=0x56286a9a4c68) at util/fifo8.c:66
#3 0x00005628683e0b8e in fifo32_pop (fifo=0x56286a9a4c68) at include/qemu/fifo32.h:137
#4 0x00005628683e0efb in spi_read (opaque=0x56286a9a4850, addr=4, size=4) at hw/ssi/mss-spi.c:168
#5 0x0000562867f96801 in memory_region_read_accessor (mr=0x56286a9a4b60, addr=16, value=0x7ffeecb0c5c8, size=4, shift=0, mask=4294967295, attrs=...) at memory.c:439
#6 0x0000562867f96cdb in access_with_adjusted_size (addr=16, value=0x7ffeecb0c5c8, size=4, access_size_min=1, access_size_max=4, access_fn=0x562867f967c3 <memory_region_read_accessor>, mr=0x56286a9a4b60, attrs=...) at memory.c:569
#7 0x0000562867f99940 in memory_region_dispatch_read1 (mr=0x56286a9a4b60, addr=16, pval=0x7ffeecb0c5c8, size=4, attrs=...) at memory.c:1420
#8 0x0000562867f99a08 in memory_region_dispatch_read (mr=0x56286a9a4b60, addr=16, pval=0x7ffeecb0c5c8, size=4, attrs=...) at memory.c:1447
#9 0x0000562867f38721 in flatview_read_continue (fv=0x56286aec6360, addr=1073745936, attrs=..., buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4, addr1=16, l=4, mr=0x56286a9a4b60) at exec.c:3385
#10 0x0000562867f38874 in flatview_read (fv=0x56286aec6360, addr=1073745936, attrs=..., buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4) at exec.c:3423
#11 0x0000562867f388ea in address_space_read_full (as=0x56286aa3e890, addr=1073745936, attrs=..., buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4) at exec.c:3436
#12 0x0000562867f389c5 in address_space_rw (as=0x56286aa3e890, addr=1073745936, attrs=..., buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4, is_write=false) at exec.c:3466
#13 0x0000562867f3bdd7 in cpu_memory_rw_debug (cpu=0x56286aa19d00, addr=1073745936, buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4, is_write=0) at exec.c:3976
#14 0x000056286811ed51 in memory_dump (mon=0x56286a8c32d0, count=1, format=120, wsize=4, addr=1073745936, is_physical=0) at monitor/misc.c:730
#15 0x000056286811eff1 in hmp_memory_dump (mon=0x56286a8c32d0, qdict=0x56286b15c400) at monitor/misc.c:785
#16 0x00005628684740ee in handle_hmp_command (mon=0x56286a8c32d0, cmdline=0x56286a8caeb2 "0x40001010") at monitor/hmp.c:1082
From the datasheet "Actel SmartFusion Microcontroller Subsystem
User's Guide" Rev.1, Table 13-3 "SPI Register Summary", this
register has a reset value of 0.
Check the FIFO is not empty before accessing it, else log an
error message.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190709113715.7761-3-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both lqspi_read() and lqspi_load_cache() expect a 32-bit
aligned address.
>From UG1085 datasheet [*] chapter on 'Quad-SPI Controller':
Transfer Size Limitations
Because of the 32-bit wide TX, RX, and generic FIFO, all
APB/AXI transfers must be an integer multiple of 4-bytes.
Shorter transfers are not possible.
Set MemoryRegionOps.impl values to force 32-bit accesses,
this way we are sure we do not access the lqspi_buf[] array
out of bound.
[*] https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Lei Sun found while auditing the code that a CPU write would
trigger a NULL pointer dereference.
>From UG1085 datasheet [*] AXI writes in this region are ignored
and generates an AXI Slave Error (SLVERR).
Fix by implementing the write_with_attrs() handler.
Return MEMTX_ERROR when the region is accessed (this error maps
to an AXI slave error).
[*] https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf
Reported-by: Lei Sun <slei.casper@gmail.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the next commit we will implement the write_with_attrs()
handler. To avoid using different APIs, convert the read()
handler first.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The DRAM address of a DMA transaction depends on the DRAM base address
of the SoC. Inform the SMC controller model with this value.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190618165311.27066-15-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the stripe8() function we use a variable length array; however
we know that the maximum length required is MAX_NUM_BUSSES. Use
a fixed-length array and an assert instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190328152635.2794-1-peter.maydell@linaro.org
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The m25p80 models dummy cycles using byte transfers. This works well
when the transfers are initiated by the QEMU model of a SPI controller
but when these are initiated by the OS, it breaks emulation.
Snoop the SPI transfer to catch commands requiring dummy cycles and
replace them with byte transfers compatible with the m25p80 model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20190124140519.13838-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMC controllers have a register containing the byte that will be
used as dummy output. It can be modified by software.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190124140519.13838-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The model should expose one control register per possible CS. When
testing the validity of the register number in the read operation,
replace 's->num_cs' by 'ctrl->max_slaves' which represents the maximum
number of flash devices a controller can handle.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190124140519.13838-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
0xFFFFFFFF should be returned for non implemented registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190124140519.13838-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move from the legacy SysBusDevice::init method to using DeviceState::realize.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20181002212522.23303-5-f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-6-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the PL022, register offset 0x20 is the ICR, a write-only
interrupt-clear register. Register offset 0x24 is DMACR, the DMA
control register. We were incorrectly implementing (a stub version
of) DMACR at 0x20, and not implementing anything at 0x24. Fix this
bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-21-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL022 interrupt registers have bits allocated as:
0: ROR (receive overrun)
1: RT (receive timeout)
2: RX (receive FIFO half full or less)
3: TX (transmit FIFO half full or less)
A cut and paste error meant we had the wrong value for
the PL022_INT_RT constant. This bug doesn't affect device
behaviour, because we don't implement the receive timeout
feature and so never set that interrupt bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-20-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Move from the legacy SysBusDevice::init method to using
DeviceState::realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-19-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Use the DeviceState vmsd pointer rather than calling vmstate_register()
directly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-18-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently the PL022 calls pl022_reset() from its class init
function. Make it register a DeviceState reset method instead,
so that we reset the device on system reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-17-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl022's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
While we're adding the new file to MAINTAINERS, add
also the .c file, which was missing an entry.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-16-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We now support direct execution from MMIO regions in the
core memory subsystem. This means that we don't need to
have device-specific support for it, and we can remove
the request_ptr handling from the Xilinx SPIPS device.
(It was broken anyway due to race conditions, and disabled
by default.)
This device is the only in-tree user of this API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Message-id: 20180817114619.22354-2-peter.maydell@linaro.org
The current emulation will clear the XCH bit when a burst finishes.
This is not quite correct. According to the i.MX7d referemce manual,
Rev 0.1, §10.1.7.3:
This bit [XCH] is cleared automatically when all data in the TXFIFO
and the shift register has been shifted out.
So XCH should be cleared when the FIFO empties, not on completion of a
burst. The FIFO is 64 x 32 bits = 2048 bits, while the max burst size
is larger at 4096 bits. So it's possible that the burst is not finished
after the TXFIFO empties.
Sending a large block (> 2048 bits) with the Linux driver will use a
burst that is larger than the TXFIFO. After the TXFIFO has emptied XCH
does not become unset, as the burst is not yet finished.
What should happen after the TXFIFO empties is the driver will refill it
and set XCH. The rising edge of XCH will trigger another transfer to
begin. However, since the emulation does not set XCH to 0, there is no
rising edge and the next trasfer never begins.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Message-id: 20180731201056.29257-1-tpiepho@impinj.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180624040609.17572-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Qspi dma has a burst length of 64 bytes, So limit the transactions w.r.t
dma-burst-size property.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1529660880-30376-1-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Also handle the fake transfers for dummy bytes in this setup
routine. It will be useful when we activate MMIO execution.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only the flash type is strapped by HW. The 4BYTE mode is set by
firmware when the flash device is detected.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When configured in dual I/O mode, address and data are sent in dual
mode, including the dummy byte cycles in between. Adapt the count to
the IO setting.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A link property can be set during creation, with
object_property_add_link() and later with object_property_set_link().
add_link() doesn't add a reference to the target object, while
set_link() does.
Furthemore, OBJ_PROP_LINK_UNREF_ON_RELEASE flags, set during add_link,
says whether a reference must be released when the property is destroyed.
This can lead to leaks if the property was later set_link(), as the
added reference is never released.
Instead, rename OBJ_PROP_LINK_UNREF_ON_RELEASE to OBJ_PROP_LINK_STRONG
and use that has an indication on how the link handle reference
management in set_link().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180531195119.22021-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
SNOOP_NONE state handle is moved above in the if ladder, as it's same
as SNOOP_STRIPPING during data cycles.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 1524119244-1240-1-git-send-email-saipava@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use 8 dummy cycles (4 dummy bytes) with the QIOR/QIOR4 commands in legacy mode
for matching what is expected by Micron (Numonyx) flashes (the default target
flash type of the QSPI).
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180223232233.31482-3-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Assert only the lower cs on bus 0 and upper cs on bus 1 when both buses and
chip selects are enabled (e.g reading/writing with stripe).
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180223232233.31482-2-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
Coverity found that the variable tx_rx in the function
xilinx_spips_flush_txfifo was being used uninitialized (CID 1383841). This
patch corrects this by always initializing tx_rx to zeros.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20180124215708.30400-1-frasse.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The point of writing a macro embedded in a 'do { ... } while (0)'
loop (particularly if the macro has multiple statements or would
otherwise end with an 'if' statement) is so that the macro can be
used as a drop-in statement with the caller supplying the
trailing ';'. Although our coding style frowns on brace-less 'if':
if (cond)
statement;
else
something else;
that is the classic case where failure to use do/while(0) wrapping
would cause the 'else' to pair with any embedded 'if' in the macro
rather than the intended outer 'if'. But conversely, if the macro
includes an embedded ';', then the same brace-less coding style
would now have two statements, making the 'else' a syntax error
rather than pairing with the outer 'if'. Thus, even though our
coding style with required braces is not impacted, ending a macro
with ';' makes our code harder to port to projects that use
brace-less styles.
The change should have no semantic impact. I was not able to
fully compile-test all of the changes (as some of them are
examples of the ugly bit-rotting debug print statements that are
completely elided by default, and I didn't want to recompile
with the necessary -D witnesses - cleaning those up is left as a
bite-sized task for another day); I did, however, audit that for
all files touched, all callers of the changed macros DID supply
a trailing ';' at the callsite, and did not appear to be used
as part of a brace-less conditional.
Found mechanically via: $ git grep -B1 'while (0);' | grep -A1 \\\\
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171201232433.25193-7-eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use memset() instead of a for loop to zero all of the registers.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: c076e907f355923864cb1afde31b938ffb677778.1513104804.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Following the ZynqMP register spec let's ensure that all reset values
are set.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 19836f3e0a298b13343c5a59c87425355e7fd8bd.1513104804.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update the reset value to match the latest ZynqMP register spec.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: c03e51d041db7f055596084891aeb1e856e32b9f.1513104804.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the Zynq Ultrascale MPSoc Generic QSPI.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-13-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Don't set TX FIFO UNDERFLOW interrupt after transmitting the commands.
Also update interrupts after reading out the interrupt status.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-12-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for 4 byte addresses in the LQSPI and correct LQSPI_CFG_SEP_BUS.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-11-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for zero pumping according to the transfer size register.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-10-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make tx/rx_data_bytes more generic so they can be reused (when adding
support for the Zynqmp Generic QSPI).
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-9-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the RX discard and RX drain functionality. Also transmit
one byte per dummy cycle (to the flash memories) with commands that require
these.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-8-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update striping functionality to be big-endian bit order (as according to
the Zynq-7000 Technical Reference Manual). Output thereafter the even bits
into the flash memory connected to the lower QSPI bus and the odd bits into
the flash memory connected to the upper QSPI bus.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-7-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the FlashCMD enum, XilinxQSPIPS and XilinxSPIPSClass structures to the
header for consistency (struct XilinxSPIPS is found there). Also move out
a define and remove two double included headers (while touching the code).
Finally, add 4 byte address commands to the FlashCMD enum.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-6-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixed incorrect frame size mask, validated maximum frame
size in spi_write and removed dead code.
Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1508898544-10307-1-git-send-email-sundeep.lkml@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds mmio-exec property to workaround the migration bug.
When enabled the migration is blocked and will return an error.
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1502438052-5117-1-git-send-email-frederic.konrad@adacore.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows to execute from the lqspi area.
When the request_ptr is called the device loads 1024bytes from the SPI device.
Then this code can be executed by the guest.
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
The size of a segment is not necessarily a power of 2.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1486648058-520-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
HW works fine in normal read mode with dummy bytes being set. So let's
check this case to not transfer bytes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1486648058-520-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing fast read, a certain amount of dummy bytes should be sent
before the read. This number is configurable in the controler CE0
Control Register and needs to be modeled using fake transfers to the
flash module.
This only supports command mode. User mode requires more work and a
possible extension of the m25p80 device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Message-id: 1484751701-2646-1-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SMC controllers have a mode (Command mode) in which
accesses to the flash content are no different than doing MMIOs. The
controller generates all the necessary commands to load (or store)
data in memory.
However, accesses are restricted to the segment window assigned the
the flash module by the controller. This window is defined by the
Segment Address Register.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-8-git-send-email-clg@kaod.org
[PMM: Deleted now-unused aspeed_smc_is_usermode() function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SPI controller of the AST2400 SoC has less registers. So we can
adjust the size of the memory region holding the registers depending
on the controller type. We can also remove the guest_error logging
which is useless as the range of the region is strict enough.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1483979087-32663-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is getting difficult to read. Also add a 'has_dma' field for each
controller type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-6-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On the AST2500 SoC, the FMC controller flash type is fixed to SPI for
CE0 and CE1 and 4BYTE mode is autodetected for CE0.
On the AST2400 SoC, the FMC controller flash type and 4BYTE mode are
strapped with register SCU70. We use the default settings from the
palmetto-bmc machine for now.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the routines prototype to use a 'AspeedSMCFlash *' instead of
'AspeedSMCState *'. The result will help in making future changes
clearer.
Also change aspeed_smc_update_cs() which uselessly loops on all slave
devices to update their status.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead, we can simply set the irq level when unselecting the slave
devices. This change prepares ground for a subsequent cleanup of the
aspeed_smc_update_cs() routine which uselessly loops on all slaves to
update their status.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1483979087-32663-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is useless as reset will be called later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Message-id: 1483979087-32663-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the documentation it is not clear what this SPI register is about.
Moreover, neither linux driver nor xvisor driver are using this SPI register.
For now we just remove it and issue a log on register write access.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 20170107122047.26300-1-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The HW does not enforce all the rules in the specs and allows a few
"curious" setups like zero size segments and overlaps. So change the
model to be in sync but keep the warnings which are always interesting
for debug.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1480434248-27138-13-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ASAN complains about buffer overflow when running:
aarch64-softmmu/qemu-system-aarch64 -machine xilinx-zynq-a9
==476==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x602000035e38 at pc 0x000000f75253 bp 0x7ffc597e0ec0 sp 0x7ffc597e0eb0
READ of size 8 at 0x602000035e38 thread T0
#0 0xf75252 in xilinx_spips_realize hw/ssi/xilinx_spips.c:623
#1 0xb9ef6c in device_set_realized hw/core/qdev.c:918
#2 0x129ae01 in property_set_bool qom/object.c:1854
#3 0x1296e70 in object_property_set qom/object.c:1088
#4 0x129dd1b in object_property_set_qobject qom/qom-qobject.c:27
#5 0x1297168 in object_property_set_bool qom/object.c:1157
#6 0xb9aeac in qdev_init_nofail hw/core/qdev.c:358
#7 0x78a5bf in zynq_init_spi_flashes /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:125
#8 0x78af60 in zynq_init /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:238
#9 0x998eac in main /home/elmarco/src/qemu/vl.c:4534
#10 0x7f96ed692730 in __libc_start_main (/lib64/libc.so.6+0x20730)
#11 0x41d0a8 in _start (/home/elmarco/src/qemu/aarch64-softmmu/qemu-system-aarch64+0x41d0a8)
0x602000035e38 is located 0 bytes to the right of 8-byte region [0x602000035e30,0x602000035e38)
allocated by thread T0 here:
#0 0x7f970b014e60 in malloc (/lib64/libasan.so.3+0xc6e60)
#1 0x7f96f15b0e18 in g_malloc (/lib64/libglib-2.0.so.0+0x4ee18)
#2 0xb9ef6c in device_set_realized hw/core/qdev.c:918
#3 0x129ae01 in property_set_bool qom/object.c:1854
#4 0x1296e70 in object_property_set qom/object.c:1088
#5 0x129dd1b in object_property_set_qobject qom/qom-qobject.c:27
#6 0x1297168 in object_property_set_bool qom/object.c:1157
#7 0xb9aeac in qdev_init_nofail hw/core/qdev.c:358
#8 0x78a5bf in zynq_init_spi_flashes /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:125
#9 0x78af60 in zynq_init /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:238
#10 0x998eac in main /home/elmarco/src/qemu/vl.c:4534
#11 0x7f96ed692730 in __libc_start_main (/lib64/libc.so.6+0x20730)
s->spi is allocated with the size of num_busses which may be 1 (by
default). Change to use a loop up to s->num_busses also for the
call to ssi_auto_connect_slaves().
Reported-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SMC controller on the Aspeed SoC has a set of registers to
configure the mapping of each flash module in the SoC address
space. Writing to these registers triggers a remap of the memory
region and the spec requires a certain number of checks before doing
so.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMC controller on the Aspeed SoC has a set of registers to
configure the mapping of each flash module in the SoC address
space. These mapping windows are configurable even though no SPI slave
is attached to the controller.
Also rewrite a bit the comments in the code on this topic.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-6-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMC controllers on the Aspeed AST2500 SoC are very similar to the
ones found on the AST2400. The differences are on the number of
supported flash modules and their default mappings in the SoC address
space.
The Aspeed AST2500 has one SPI controller for the BMC firmware and two
for the host firmware. All controllers have now the same set of
registers compatible with the AST2400 FMC controller and the legacy
'SMC' controller is fully gone.
We keep the FMC object to act as the BMC SPI controller and add a new
SPI controller for the host. We also have to introduce new type names
to handle the differences in the flash modules memory mappping.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will ease the definition of the new controllers for the AST2500
SoC and also ease the support of the segment registers, which provide
a way to reconfigure the mapping window of each slave.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'char const' means the same thing as 'const char', but we
use the former in only a handful of places and we use the
latter over six thousand times. Switch the imx reg_name()
functions to bring them in line with everything else.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
U-boot does SPI timing calibration using DMA tranfers. To let the
initialization continue, we fake success by setting the DMA status of
the Interrupt Control Register.
For the moment, DMA support is not required as it is not used in
normal operation.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467994016-11678-4-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
aspeed_smc_is_implemented() filters invalid registers in a peculiar
way. Let's remove it and open code the if conditions. It serves the
same purpose, the aesthetic is better, and new registers can easily be
added.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467994016-11678-3-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Each controller on the ast2400 has a memory range on which it maps its
flash module slaves. Each slave is assigned a memory segment for its
mapping that can be changed at bootime with the Segment Address
Register. This is not supported in the current implementation so we
are using the defaults provided by the specs.
Each SPI flash slave can then be accessed in two modes: Command and
User. When in User mode, accesses to the memory segment of the slaves
are translated in SPI transfers. When in Command mode, the HW
generates the SPI commands automatically and the memory segment is
accessed as if doing a MMIO. Other SPI controllers call that mode
linear addressing mode.
For this purpose, we are adding below each crontoller an array of
structs gathering for each SPI flash module, a segment rank, a
MemoryRegion to handle the memory accesses and the associated SPI
slave device, which should be a m25p80.
Only the User mode is supported for now but we are preparing ground
for the Command mode. The framework is sufficient to support Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-8-git-send-email-clg@kaod.org
[PMM: Use g_new0() rather than g_malloc0()]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 soc includes a static memory controller for the BMC
which supports NOR, NAND and SPI flash memory modules. This controller
has two modes : the SMC for the legacy interface which supports only
one module and the FMC for the new interface which supports up to five
modules. The AST2400 also includes a SPI only controller used for the
host firmware, commonly called BIOS on Intel. It can be used in three
mode : a SPI master, SPI slave and SPI pass-through
Below is the initial framework for the SMC controller (FMC mode only)
and the SPI controller: the sysbus object, MMIO for registers
configuration and controls. Each controller has a SPI bus and a
configurable number of CS lines for SPI flash slaves.
The differences between the controllers are small, so they are
abstracted using indirections on the register numbers.
Only SPI flash modules are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-7-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added one missing error_propagate]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables qemu to handle late inits and report errors. All the SSI
slave routine names were changed accordingly. Code was modified to
handle errors when possible (m25p80 and ssi-sd)
Tested with the m25p80 slave object.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-38-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-36-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Separate out the XilinxSPIPS struct into a separate header
file.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the ssi.h include file into the ssi directory.
While touching the code also fix the typdef lines as
checkpatch complains.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To properly indicate they are unconnected.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
To get it out of the default GPIO list. This allows child devices to
use the un-named GPIO namespace without having to be SSI aware. That
is, there is no more need for machines to know about the obscure
policy where GPIO 0 is the SSI chip-select and GPIO 1..N are the
concrete class GPIOs (defined locally as 0..N-1).
This is most notable in stellaris, which uses a device which has both
SSI and concrete level GPIOs.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CVE-2013-4530
pl022.c did not bounds check tx_fifo_head and
rx_fifo_head after loading them from file and
before they are used to dereference array.
Reported-by: Michael S. Tsirkin <mst@redhat.com
Reported-by: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Remove two legacy ->qbus style casts from TYPE_SSI_BUS to TYPE_BUS in
ssi.c.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[AF: Convert one missing ->qbus and rename parent field]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Convert legacy ->qdev style casts from TYPE_SSI_SLAVE to TYPE_DEVICE.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[AF: Introduce local DeviceState variable for transition to QOM realize]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The LQSPI bus attachment supports byte/halfword and misaligned
accesses. Fixed. Refactored the LQSPI cache to be byte-wise
instead of word wise accordingly.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 5ec47b13563ad2d22105a1f26186d7756718394b.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do 16 words per fifo flush. Increases performance and decreases
debug verbosity. This data depth has no real hardware analogue,
so just go with something that has reasonable performance.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 5621ee4621941d3639b5cacfdec26bd3148f31d5.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The debug printfs on every SPI operation is extremely verbose. Add
a second level of debug for this.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: f63478b8e5b29cc011cdc10e29f8537bb2fc2b5e.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is worth keeping track of when debugging the device model.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: d3b44ecf23d671798b062eee5dc362c716ea54cd.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The QSPI controller was using byte-wide stripes when striping across
the two flashes in dual parallel mode. The real hardware however uses
individual bit striping. QEMU misbehaves in the (corner) case where
data is written/read in dual-parallel mode and read/written back in
single mode.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 718a61df1bf746ec06f6da44d12f8317af7b08ce.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CTRL register was RAZ/WI on some of the RW bits. Even though the
function behind these bits is invalid in QEMU, they should still be
guest accessible. Fix.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: b7aaad93163ce4af0c428635804ac7b77a567b25.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The LQSPI mode is supposed to work via the automatic CS mode feature
rather than manipulate CS lines itself. Now that auto CS is implemented
remove LQSPIs CS mode override logic. There is still a need to
manipulate the U_PAGE bit in LQSPI config register to implement
dual-stack mode however.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 000c8dd54df09523f17052638100722ef0f5a3af.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the automatic CS control feature. If the MANUAL_CS bit is
cleared then the chip select stay de-asserted as long as the tx FIFO
is empty.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 1d67383adc42761af715a93f161344b9284dfc9a.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SPI has a mode where it automatically starts based on tx fifo
occupancy. Implemented.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: f4e9accb5de87b526fff6ed937f63278db76533b.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Invalidate the LQSPI cached page when transitioning into LQSPI mode.
Otherwise there is a possibility that the controller will return stale
data to the guest when transitioning back to LQ_MODE after a page
program.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 677490a6ee1953fe5d366e599d665de645ac84db.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QSPI has a bigger FIFO than the regular SPI controller. Differentiate
between the two with correct FIFO sizes for each.
This is the first piece of class data for SPIPS, so this patch sees
the creation of the XilinxSPIPSClass definition and assoicated QOM
constructs.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: acee25dd5e203215cbc15ca5d3cb5d5b2efebe7b.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
You really need this is you want to track a guest banging on LQSPI.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 26e508da4af11058d37daa777064c9e5c2a69abb.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The real hardware does not produce interrupts in LQSPI mode. Inhibit
generation of interrupts when the LQ_MODE bit is set.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: dff794a06872009ea7e5733ce6adcff94d18bbd0.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By default these interrupts are clear on read.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 999ff0091ed3cc3969a431bf55c00ef934cecc8e.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make SPI and QSPI different classes. QSPIPS is setup as a child of SPIPS.
Only QSPI has the LQSPI functionality, so move all that to the child class.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 2cdd0cadb5ba77ca02fde5cae627852dc9a64c71.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
