This patch adds the barebones of the PMU logic by enabling cycle
counting. The overall logic goes as follows:
- MMCR0 reg initial value is set to 0x80000000 (MMCR0_FC set) to avoid
having to spin the PMU right at system init;
- to retrieve the events that are being profiled, pmc_get_event() will
check the current MMCR0 and MMCR1 value and return the appropriate
PMUEventType. For PMCs 1-4, event 0x2 is the implementation dependent
value of PMU_EVENT_INSTRUCTIONS and event 0x1E is the implementation
dependent value of PMU_EVENT_CYCLES. These events are supported by IBM
Power chips since Power8, at least, and the Linux Perf driver makes use
of these events until kernel v5.15. For PMC1, event 0xF0 is the
architected PowerISA event for cycles. Event 0xFE is the architected
PowerISA event for instructions;
- if the counter is frozen, either via the global MMCR0_FC bit or its
individual frozen counter bits, PMU_EVENT_INACTIVE is returned;
- pmu_update_cycles() will go through each counter and update the
values of all PMCs that are counting cycles. This function will be
called every time a MMCR0 update is done to keep counters values
up to date. Upcoming patches will use this function to allow the
counters to be properly updated during read/write of the PMCs
and MMCR1 writes.
Given that the base CPU frequency is fixed at 1Ghz for both powernv and
pseries clock, cycle calculation assumes that 1 nanosecond equals 1 CPU
cycle. Cycle value is then calculated by adding the elapsed time, in
nanoseconds, of the last cycle update done via pmu_update_cycles().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211201151734.654994-3-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This patch starts an IBM Power8+ compatible PMU implementation by adding
the representation of PMU events that we are going to sample,
PMUEventType. This enum represents a Perf event that is being sampled by
a specific counter 'sprn'. Events that aren't available (i.e. no event
was set in MMCR1) will be of type 'PMU_EVENT_INVALID'. Events that are
inactive due to frozen counter bits state are of type
'PMU_EVENT_INACTIVE'. Other types added in this patch are
PMU_EVENT_CYCLES and PMU_EVENT_INSTRUCTIONS. More types will be added
later on.
Let's also add the required PMU cycle overflow timers. They will be used
to trigger cycle overflows when cycle events are being sampled. This
timer will call cpu_ppc_pmu_timer_cb(), which in turn calls
fire_PMC_interrupt(). Both functions are stubs that will be implemented
later on when EBB support is added.
Two new helper files are created to host this new logic.
cpu_ppc_pmu_init() will init all overflow timers during CPU init time.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211201151734.654994-2-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When Altivec support was added to the e6500 kernel in 2012[1], the
QEMU code was not changed, so we don't register the VPU/VPUA
exceptions for the e6500:
qemu: fatal: Raised an exception without defined vector 73
Note that the error message says 73, instead of 32, which is the IVOR
for VPU. This is because QEMU knows only knows about the VPU interrupt
for the 7400s. In theory, we should not be raising _that_ VPU
interrupt, but instead another one specific for the e6500.
We unfortunately cannot register e6500-specific VPU/VPUA interrupts
because the SPEU/EFPDI interrupts also use IVOR32/33. These are
present only in the e500v1/2 versions. From the user manual:
e500v1, e500v2: only SPEU/EFPDI/EFPRI
e500mc, e5500: no SPEU/EFPDI/EFPRI/VPU/VPUA
e6500: only VPU/VPUA
So I'm leaving IVOR32/33 as SPEU/EFPDI, but altering the dispatch code
to convert the VPU #73 to a #32 when we're in the e6500. Since the
handling for SPEU and VPU is the same this is the only change that's
needed. The EFPDI is not implemented and will cause an abort. I don't
think it worth it changing the error message to take VPUA into
consideration, so I'm not changing anything there.
This bug was discussed in the thread:
https://lists.gnu.org/archive/html/qemu-ppc/2021-06/msg00222.html
1- https://git.kernel.org/torvalds/c/cd66cc2ee52
Reported-by: <mario@locati.it>
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213133542.2608540-1-farosas@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
They have been there since 2007 without any board using them, most
were protected by a TODO define. Drop support.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211202191108.1291515-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The exception model id for 601v has been removed without mention
why. I assume it was inadvertent and restore it here.
Fixes: b632a148b6 ("target-ppc: Use QOM method dispatch for MMU fault handling")
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211208123029.2052625-4-farosas@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The 603e uses the same exception code as 603 so we don't need a
dedicated entry for it.
This is only a removal of redundant code, no functional change.
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211208123029.2052625-3-farosas@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The Floating-point Unavailable and Decrementer interrupts are being
registered at the same 0x900 address. The FPU should be at 0x800
instead.
Verified on MPC555, MPC860 and MPC885 user manuals.
Reported-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211208123029.2052625-2-farosas@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(Applies to 7441, 7445, 7450, 7451, 7455, 7457, 7447, 7447a and 7448)
The QEMU-side software TLB implementation for the 7450 family of CPUs
is being removed due to lack of known users in the real world. The
last users in the code were removed by the two previous commits.
A brief history:
The feature was added in QEMU by commit 7dbe11acd8 ("Handle all MMU
models in switches...") with the mention that Linux was not able to
handle the TLB miss interrupts and the MMU model would be kept
disabled.
At some point later, commit 8ca3f6c382 ("Allow selection of all
defined PowerPC 74xx (aka G4) CPUs.") enabled the model for the 7450
family without further justification.
We have since the year 2011 [1] been unable to run OpenBIOS in the
7450s and have not heard of any other software that is used with those
CPUs in QEMU. Attempts were made to find a guest OS that implemented
the TLB miss handlers and none were found among Linux 5.15, FreeBSD 13,
MacOS9, MacOSX and MorphOS 3.15.
All CPUs that registered this feature were moved to an MMU model that
replaces the software TLB with a QEMU hardware TLB
implementation. They can now run the same software as the 7400 CPUs,
including the OSes mentioned above.
References:
- https://bugs.launchpad.net/qemu/+bug/812398https://gitlab.com/qemu-project/qemu/-/issues/86
- https://lists.nongnu.org/archive/html/qemu-ppc/2021-11/msg00289.html
message id: 20211119134431.406753-1-farosas@linux.ibm.com
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211130230123.781844-4-farosas@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The e600 CPU is a successor of the 7448 and like all the 7450s CPUs,
it has an optional software TLB feature.
We have determined that there is no OS software support for the 7450
software TLB available these days. See the previous commit for more
information.
This patch disables the SPRs and instructions related to software TLB
from the e600 CPU.
No functional change intended. These facilities should be used by the
OS in interrupt handlers for interrupts that QEMU never generates.
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211130230123.781844-3-farosas@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(Applies to 7441, 7445, 7450, 7451, 7455, 7457, 7447 and 7447a)*
We have since 2011 [1] been unable to run OpenBIOS in the 7450s and
have not heard of any other software that is used with those CPUs in
QEMU. A current discussion [2] shows that the 7450 software TLB is
unsupported in Linux 5.15, FreeBSD 13, MacOS9, MacOSX and MorphOS
3.15. With no known support in firmware or OS, this means that no code
for any of the 7450 CPUs is ever ran in QEMU.
Since the implementation in QEMU of the 7400 MMU is the same as the
7450, except for the software TLB vs. hardware TLB search, this patch
changes all 7450 cpus to the 7400 MMU model. This has the practical
effect of disabling the software TLB feature while keeping other
aspects of address translation working as expected.
This allow us to run software on the 7450 family again.
*- note that the 7448 is currently aliased in QEMU for a 7400, so it
is unaffected by this change.
1- https://bugs.launchpad.net/qemu/+bug/812398https://gitlab.com/qemu-project/qemu/-/issues/86
2- https://lists.nongnu.org/archive/html/qemu-ppc/2021-11/msg00289.html
message id: 20211119134431.406753-1-farosas@linux.ibm.com
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211130230123.781844-2-farosas@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Record DAR, DSISR, and exception_index. That last means
that we must exit to cpu_loop ourselves, instead of letting
exception_index being overwritten.
This is exactly what the user-mode ppc_cpu_tlb_fill does,
so simply rename it as ppc_cpu_record_sigsegv.
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
I noticed -cpu help printing enough trailing spaces to make the output
at least 84 characters wide. Looks ugly unless the terminal is wider.
Ugly or not, trailing spaces are stupid.
The culprit is this line in x86_cpu_list_entry():
qemu_printf("x86 %-20s %-58s\n", name, desc);
This prints a string with minimum field left-justified right before a
newline. Change it to
qemu_printf("x86 %-20s %s\n", name, desc);
which avoids the trailing spaces and is simpler to boot.
A search for the pattern with "git-grep -E '%-[0-9]+s\\n'" found a few
more instances. Change them similarly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20211009152401.2982862-1-armbru@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Problem state needs to be able to read and write the PMU counters,
otherwise it won't be aware of any sampling result that the PMU produces
after a Perf run.
This patch does that in a similar fashion as already done in the
previous patches. PMCs 5 and 6 have a special condition, aside from the
constraints that are common with PMCs 1-4, where they are not part of the
PMU if MMCR0_PMCC is 0b11.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211018010133.315842-5-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Similar to the previous patch, let's add problem state read/write access to
the MMCR2 SPR, which is also a group A PMU SPR that needs to be filtered
to be read/written by userspace.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211018010133.315842-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Userspace need access to PMU SPRs to be able to operate the PMU. One of
such SPRs is MMCR0.
MMCR0, as defined by PowerISA v3.1, is classified as a 'group A' PMU
register. This class of registers has common read/write rules that are
governed by MMCR0 PMCC bits. MMCR0 is also not fully exposed to problem
state: only MMCR0_FC, MMCR0_PMAO and MMCR0_PMAE bits are
readable/writable in this case.
This patch exposes MMCR0 to userspace by doing the following:
- two new callbacks, spr_read_MMCR0_ureg() and spr_write_MMCR0_ureg(),
are added to be used as problem state read/write callbacks of UMMCR0.
Both callbacks filters the amount of bits userspace is able to
read/write by using a MMCR0_UREG_MASK;
- problem state access control is done by the spr_groupA_read_allowed()
and spr_groupA_write_allowed() helpers. These helpers will read the
current PMCC bits from DisasContext and check whether the read/write
MMCR0 operation is valid or noti;
- to avoid putting exclusive PMU logic into the already loaded
translate.c file, let's create a new 'power8-pmu-regs.c.inc' file that
will hold all the spr_read/spr_write functions of PMU registers.
The 'power8' name of this new file intends to hint about the proven
support of the PMU logic to be added. The code has been tested with the
IBM POWER chip family, POWER8 being the oldest version tested. This
doesn't mean that the PMU logic will break with any other PPC64 chip
that implements Book3s, but rather that we can't assert that it works
properly with any Book3s compliant chip.
CC: Gustavo Romero <gustavo.romero@linaro.org>
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211018010133.315842-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Restrict cpu_exec_interrupt() and its callees to sysemu.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210911165434.531552-18-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The POWER10 DD2 CPU adds an extra LPCR[HAIL] bit. DD1 doesn't have
HAIL but since it does not break the modeling and that we don't plan
to support DD1, modify the LPCR mask of all the POWER10 family.
Setting the HAIL bit is a requirement to support the scv instruction
on PowerNV POWER10 platforms since glibc-2.33.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210809134547.689560-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
arch_init.h only defines the QEMU_ARCH_* enumeration and the
arch_type global. Don't include it in files that don't use those.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210730105947.28215-8-peter.maydell@linaro.org
The function ppc_tlb_invalid_all is not compiled anymore in a TCG-less
environment, and the call to that function has been disabled in this
situation
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Message-Id: <20210708164957.28096-2-lucas.araujo@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead, use a switch on env->mmu_model. This avoids some
replicated information in cpu setup.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210621125115.67717-2-bruno.larsen@eldorado.org.br>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This isn't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210622140926.677618-3-groug@kaod.org>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This feature will no longer be useful as ppc moves to using decodetree
for TCG. And building with it enabled is no longer possible, due to
changes in opc_handler_t. Since the last commit that mentions it
happened in 2014, I think it is safe to remove it.
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Message-Id: <20210531145629.21300-5-bruno.larsen@eldorado.org.br>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function requires surce code modification to be useful, which means
it probably is not used often, and the move to using decodetree means
the statistics won't even be collected anymore.
Also removed setting dump_statistics in ppc_cpu_realize, since it was
only useful when in conjunction with ppc_cpu_dump_statistics.
Suggested-by: Richard Henderson<richard.henderson@linaro.org>
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Message-Id: <20210526202104.127910-3-bruno.larsen@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
excp_helper.c, mmu-hash64.c and mmu_helper.c have some function
declarations that are TCG-only, and couldn't be easily moved to a
TCG only file, so ifdefs were added around them.
We also needed ifdefs around some header files because helper-proto.h
includes trace/generated-helpers.h, which is never created when building
without TCG, and cpu_ldst.h includes tcg/tcg.h, whose containing folder
is not included as a -iquote. As future cleanup, we could change the
part of the configuration script to add those.
cpu_init.c also had a callback definition that is TCG only and could be
removed as part of a future cleanup (all the dump_statistics part is
almost never used and will become obsolete as we transition to using
decodetree).
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Message-Id: <20210525115355.8254-3-bruno.larsen@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The write calback decision when registering the MAS SPR has been turned
into a ternary operation, rather than an if-then-else block.
This was done because when building without TCG, even though the
compiler will optimize away the pointers to spr_write_generic*, it
doesn't optimize away the decision and assignment to the local pointer,
creating compiler errors. This cleanup looked better than using ifdefs,
so we decided to with it.
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210525115355.8254-2-bruno.larsen@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These files included helper-proto.h, but didn't use or declare any
helpers, so the #include has been removed
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210521201759.85475-6-bruno.larsen@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We no longer have any runtime modifications to this struct,
so declare them all const.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20210227232519.222663-3-richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210517105140.1062037-21-f4bug@amsat.org>
[rth: Drop declaration movement from target/*/cpu.h]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The write_elf*() handlers are used to dump vmcore images.
This feature is only meaningful for system emulation.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210517105140.1062037-19-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
VirtIO devices are only meaningful with system emulation.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210517105140.1062037-17-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Migration is specific to system emulation.
- Move the CPUClass::vmsd field to SysemuCPUOps,
- restrict VMSTATE_CPU() macro to sysemu,
- vmstate_dummy is now unused, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210517105140.1062037-16-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Introduce a structure to hold handler specific to sysemu.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210517105140.1062037-15-f4bug@amsat.org>
[rth: Squash "restrict hw/core/sysemu-cpu-ops.h" patch]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Quoting Peter Maydell [*]:
There are two ways to handle migration for
a CPU object:
(1) like any other device, so it has a dc->vmsd that covers
migration for the whole object. As usual for objects that are a
subclass of a parent that has state, the first entry in the
VMStateDescription field list is VMSTATE_CPU(), which migrates
the cpu_common fields, followed by whatever the CPU's own migration
fields are.
(2) a backwards-compatible mechanism for CPUs that were
originally migrated using manual "write fields to the migration
stream structures". The on-the-wire migration format
for those is based on the 'env' pointer (which isn't a QOM object),
and the cpu_common part of the migration data is elsewhere.
cpu_exec_realizefn() handles both possibilities:
* for type 1, dc->vmsd is set and cc->vmsd is not,
so cpu_exec_realizefn() does nothing, and the standard
"register dc->vmsd for a device" code does everything needed
* for type 2, dc->vmsd is NULL and so we register the
vmstate_cpu_common directly to handle the cpu-common fields,
and the cc->vmsd to handle the per-CPU stuff
You can't change a CPU from one type to the other without breaking
migration compatibility, which is why some guest architectures
are stuck on the cc->vmsd form. New targets should use dc->vmsd.
To avoid new targets to start using type (2), rename cc->vmsd as
cc->legacy_vmsd. The correct field to implement is dc->vmsd (the
DeviceClass one).
See also commit b170fce3dd ("cpu: Register VMStateDescription
through CPUState") for historic background.
[*] https://www.mail-archive.com/qemu-devel@nongnu.org/msg800849.html
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210517105140.1062037-13-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This function was forgotten in the cpu_init code motion series, but it
seems to be used regardless of TCG, and so needs to be moved to support
disabling TCG.
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Message-Id: <20210512140813.112884-4-bruno.larsen@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some functions unrelated to TCG use helper_m{t,f}vscr, so generic versions
of those functions were added to cpu.c, in preparation for compilation
without TCG
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Message-Id: <20210512140813.112884-2-bruno.larsen@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
finished isolation of CPU initialization logic from
translation logic. CPU initialization now only has common code
and may or may not call accelerator-specific code, as the
build options require.
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210507115551.11436-1-bruno.larsen@eldorado.org.br>
[dwg: Fix compile error with clang linux-user builds]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
