Per AM53C974 datasheet, definition of "SCSI Bus and Control (SBAC)"
register:
Bit 24 'STATUS' Write Erase Control
This bit controls the Write Erase feature on bits 3:1 and bit 6 of the DMA
Status Register ((B)+54h). When this bit is programmed to '1', the state
of bits 3:1 are preserved when read. Bits 3:1 are only cleared when a '1'
is written to the corresponding bit location. For example, to clear bit 1,
the value of '0000_0010b' should be written to the register. When the DMA
Status Preserve bit is '0', bits 3:1 are cleared when read.
The status register is currently defined to bit 12, not bit 24.
Also, its implementation is reversed: The status is auto-cleared if
the bit is set to 1, and must be cleared explicitly when the bit is
set to 0. This results in spurious interrupts reported by the Linux
kernel, and in some cases even results in stalled SCSI operations.
Set SBAC_STATUS to bit 24 and reverse the logic to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <1543442171-24863-1-git-send-email-linux@roeck-us.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because they are supposed to remain const.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181114132931.22624-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Under heavy IO (e.g. fio) the queue is not checked frequently enough for
pending commands. As a result some pending commands are timed out by the
linux sym53c8xx driver, which sends SCSI Abort messages for the timed out
commands. The SCSI Abort messages result in linux errors, which show up
on the console and in /var/log/messages.
e.g.
sd 0:0:3:0: [sdd] tag#33 ABORT operation started
scsi target0:0:3: control msgout:
80 20 47 d
sd 0:0:3:0: ABORT operation complete.
scsi target0:0:4: message d sent on bad reselection
Now following a WAIT DISCONNECT Script instruction, and if there is no
current command, check for a pending command on the queue and if one
exists call lsi_reselect().
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Message-Id: <1541776692-12271-1-git-send-email-george.kennedy@oracle.com>
[For safety, add a s->current check in lsi_update_irq - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 40dce4ee6 "scsi-disk: fix rerror/werror=ignore" introduced a
bug which causes qemu to crash with the assertion error below if the
host file or disk returns an error:
qemu-system-x86_64: hw/scsi/scsi-bus.c:1374: scsi_req_complete:
Assertion `req->status == -1' failed.
Kevin Wolf suggested this fix:
< kwolf> Hm, should the final return false; in that patch
actually be a return true?
< kwolf> Because I think he didn't intend to change anything
except BLOCK_ERROR_ACTION_IGNORE
Buglink: https://bugs.launchpad.net/qemu/+bug/1804323
Fixes: 40dce4ee61
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass other sense, such as UNIT_ATTENTION or BUSY, directly to the
guest.
Reported-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Emulation of the block limits VPD page called back into scsi-disk.c,
which however expected the request to be for a SCSIDiskState and
accessed a scsi-generic device outside the bounds of its struct
(namely to retrieve s->max_unmap_size and s->max_io_size).
To avoid this, move the emulation code to a separate function that
takes a new SCSIBlockLimits struct and marshals it into the VPD
response format.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A device can report an excessive number of VPD pages when asked for a
list; this can cause an out-of-bounds access to buf in
scsi_generic_set_vpd_bl_emulation. It should not happen, but
it is technically not incorrect so handle it: do not check any byte
past the allocation length that was sent to the INQUIRY command.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Block limits emulation is just placing 0xb0 as the final byte of the
VPD pages list. However, VPD page numbers must be sorted, so change
that to an in-place insert. Since I couldn't find any disk that triggered
the loop more than once, this was tested by adding manually 0xb1
at the end of the list and checking that 0xb0 was added before.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While writing a message in 'lsi_do_msgin', message length value
in 'msg_len' could be invalid due to an invalid migration stream.
Add an assertion to avoid an out of bounds access, and reject
the incoming migration data if it contains an invalid message
length.
Discovered by Deja vu Security. Reported by Oracle.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20181026194314.18663-1-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are 3 virtqueues (ctrl, event and cmd) for virtio scsi device,
but seabios will only set the physical address for the 3rd one (cmd).
Then in vhost_virtqueue_start(), virtio_queue_get_desc_addr()
will be 0 for ctrl and event vq.
In this case, ctrl and event vq are not initialized.
vhost_verify_ring_mappings may use uninitialized vhost_virtqueue
such that vhost_verify_ring_part_mapping returns ENOMEM.
When encountered this problem, we got the following logs:
qemu-system-x86_64: Unable to map available ring for ring 0
qemu-system-x86_64: Verify ring failure on region 0
Signed-off-by: Forrest Liu <forrestl@synology.com>
Signed-off-by: yuchenlin <yuchenlin@synology.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
rerror=ignore was returning true from scsi_handle_rw_error but the callers were not
calling scsi_req_complete when rerror=ignore returns true (this is the correct thing
to do when true is returned after executing a passthrough command). Fix this by
calling it in scsi_handle_rw_error.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a command fails with a sense that scsi_sense_buf_to_errno converts to
ECANCELED/EAGAIN/ENOTCONN or with a unit attention, scsi_req_complete is
called twice. This caused a crash.
Reported-by: Wangguang <wang.guangA@h3c.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When [2] was fixed it was agreed that adding and calling post_plug()
callback after device_reset() was low risk approach to hotfix issue
right before release. So it was merged instead of moving already
existing plug() callback after device_reset() is called which would
be more risky and require all plug() callbacks audit.
Looking at the current plug() callbacks, it doesn't seem that moving
plug() callback after device_reset() is breaking anything, so here
goes agreed upon [3] proper fix which essentially reverts [1][2]
and moves plug() callback after device_reset().
This way devices always comes to plug() stage, after it's been fully
initialized (including being reset), which fixes race condition [2]
without need for an extra post_plug() callback.
1. (25e897881 "qdev: add HotplugHandler->post_plug() callback")
2. (8449bcf94 "virtio-scsi: fix hotplug ->reset() vs event race")
3. https://www.mail-archive.com/qemu-devel@nongnu.org/msg549915.html
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1539696820-273275-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Pierre Morel<pmorel@linux.ibm.com>
Acked-by: Pierre Morel<pmorel@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Taking the address of a field in a packed struct is a bad idea, because
it might not be actually aligned enough for that pointer type (and
thus cause a crash on dereference on some host architectures). Newer
versions of clang warn about this. Avoid the bug by not using the
"modify in place" byte swapping functions.
This patch was produced with the following simple spatch script:
@@
expression E;
@@
-le16_to_cpus(&E);
+E = le16_to_cpu(E);
@@
expression E;
@@
-le32_to_cpus(&E);
+E = le32_to_cpu(E);
@@
expression E;
@@
-le64_to_cpus(&E);
+E = le64_to_cpu(E);
@@
expression E;
@@
-cpu_to_le16s(&E);
+E = cpu_to_le16(E);
@@
expression E;
@@
-cpu_to_le32s(&E);
+E = cpu_to_le32(E);
@@
expression E;
@@
-cpu_to_le64s(&E);
+E = cpu_to_le64(E);
followed by some minor tidying of overlong lines and bad indent.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180927134852.21490-1-peter.maydell@linaro.org>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180917053229.4853-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This option is added together with scsi-disk but is never honoured,
becuase we don't emulate the VPD page for scsi-block. We could intercept
and inject the user specified value like for max xfer len, but it's
probably not helpful since the intent of 070f80095a was for random
entropy aspects, not for performance. If emulated rotation rate is
desired, scsi-hd is more suitable.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180917083138.3948-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On some early machines the on-board PCI devices IRQs are wired directly to
the interrupt controller instead of via the PCI host bridge.
Add an optional external IRQ that if wired up via qdev will replace the
in-built PCI IRQ.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that these functions are no longer required they can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the function that will soon be used to replace lsi53c895a_create() and
lsi53c810_create().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Allow toggling on/off the VIRTIO_SCSI_F_T10_PI feature bit for both
vhost-scsi and vhost-user-scsi devices.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-4-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the enablement of preset host features into the common
vhost_scsi_common_get_features() function. This is in preparation for
having vhost-scsi also make use of host_features.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-3-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation for having vhost-scsi also make use of host_features,
move it from struct VHostUserSCSI into struct VHostSCSICommon.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-2-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The LSI 53c895a code does not handle the PPR Extended Message. Add
support to handle PPR Extended Message like SDTR and WDTR are handled.
That is, to skip past the message bytes and ignore the message.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mptsas1068 is currently listed as uncategorized device.
Mark it as storage device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <1533076133-22745-1-git-send-email-linux@roeck-us.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reinstates commit b008326744,
which was temporarily reverted for the 3.0 release so that libvirt gets
some extra time to update their command lines.
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
There is a race condition during hotplug when iothread is used. It
occurs because virtio-scsi may be processing command queues in the
iothread while the monitor performs SCSI device hotplug.
When a SCSI device is hotplugged the HotplugHandler->plug() callback is
invoked and virtio-scsi emits a rescan event to the guest.
If the guest submits a SCSI command at this point then it may be
cancelled before hotplug completes. This happens because ->reset() is
called by hw/core/qdev.c:device_set_realized() after
HotplugHandler->plug() has been called and
hw/scsi/scsi-disk.c:scsi_disk_reset() purges all requests.
This patch uses the new HotplugHandler->post_plug() callback to emit the
rescan event after ->reset(). This eliminates the race conditions where
requests could be cancelled.
Reported-by: l00284672 <lizhengui@huawei.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20180716083732.3347-3-stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current BDC VPD page (page 0xb1) is too short. This can be
seen running sg_utils:
$ sg_vpd --page=bdc /dev/sda
Block device characteristics VPD page (SBC):
Block device characteristics VPD page length too short=8
By the SCSI spec, the expected size of the SBC page is 0x40.
There is no telling how the guest will behave with a shorter
message - it can ignore it, or worse, make (wrong)
assumptions.
This patch fixes the emulation by setting the size to 0x40.
This is the output of the previous sg_vpd command after
applying it:
$ sg_vpd --page=bdc /dev/sda -v
inquiry cdb: 12 01 b1 00 fc 00
Block device characteristics VPD page (SBC):
[PQual=0 Peripheral device type: disk]
Medium rotation rate is not reported
Product type: Not specified
WABEREQ=0
WACEREQ=0
Nominal form factor not reported
FUAB=0
VBULS=0
To improve readability, this patch also adds the VBULS value
explictly and add comments on the existing fields we're
setting.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This reverts commit b008326744.
Hold off removing this for one more QEMU release (current libvirt
release still uses it.)
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180625124238.25339-10-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The error handling policy was traditionally set with -drive, but with
-blockdev it is no longer possible to set frontend options. scsi-disk
(and other block devices) have long supported qdev properties to
configure the error handling policy, so let's add these options to
usb-storage as well and just forward them to the internal scsi-disk
instance.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The VPD Block Limits Inquiry page is optional, allowing SCSI devices
to not implement it. This is the case for devices like the MegaRAID
SAS 9361-8i and Microsemi PM8069.
In case of SCSI passthrough, the response of this request is used by
the QEMU SCSI layer to set the max_io_sectors that the guest
device will support, based on the value of the max_sectors_kb that
the device has set in the host at that time. Without this response,
the guest kernel is free to assume any value of max_io_sectors
for the SCSI device. If this value is greater than the value from
the host, SCSI Sense errors will occur because the guest will send
read/write requests that are larger than the underlying host device
is configured to support. An example of this behavior can be seen
in [1].
A workaround is to set the max_sectors_kb host value back in the guest
kernel (a process that can be automated using rc.local startup scripts
and the like), but this has several drawbacks:
- it can be troublesome if the guest has many passthrough devices that
needs this tuning;
- if a change in max_sectors_kb is made in the host side, manual change
in the guests will also be required;
- during an OS install it is difficult, and sometimes not possible, to
go to a terminal and change the max_sectors_kb prior to the installation.
This means that the disk can't be used during the install process. The
easiest alternative here is to roll back to scsi-hd, install the guest
and then go back to SCSI passthrough when the installation is done and
max_sectors_kb can be set.
An easier way would be to QEMU handle the absence of the Block Limits
VPD device response, setting max_io_sectors accordingly and allowing
the guest to use the device without the hassle.
This patch adds emulation of the Block Limits VPD response for
SCSI passthrough devices of type TYPE_DISK that doesn't support
it. The following changes were made:
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply. In case the device does not
- a new function called scsi_generic_set_vpd_bl_emulation,
that is called during device realize, was created to set a
new flag 'needs_vpd_bl_emulation' of the device. This function
retrieves the Inquiry EVPD response of the device to check for
VPD BL support.
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply in case the device needs
VPD BL emulation, adding the Block Limits page (0xb0) to
the list. This will make the guest kernel aware of the
support that we're now providing by emulation.
- a new function scsi_emulate_block_limits creates the
emulated Block Limits response. This function is called
inside scsi_read_complete in case the device requires
Block Limits VPD emulation and we detected a SCSI Sense
error in the VPD Block Limits reply that was issued
from the guest kernel to the device. This error is
expected: we're reporting support from our side, but
the device isn't aware of it.
With this patch, the guest now queries the Block Limits
page during the device configuration because it is being
advertised in the Supported Pages response. It will either
receive the Block Limits page from the hardware, if it supports
it, or will receive an emulated response from QEMU. At any rate,
the guest now has the information to set the max_sectors_kb
parameter accordingly, sparing the user of SCSI sense errors
that would happen without the emulated response and in the
absence of Block Limits support from the hardware.
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Reported-by: Dac Nguyen <dacng@us.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-4-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the VPD Block Limits emulation with SCSI passthrough,
we'll issue an Inquiry request with EVPD set to retrieve
the available VPD pages of the device. This would be done in
a way similar of what scsi_generic_read_device_identification
does: create a SCSI command and a reply buffer, fill in the
sg_io_hdr_t structure, call blk_ioctl, check if an error
occurred, process the response.
This same process is done in other 2 functions, get_device_type
and get_stream_blocksize. They differ in the command/reply
buffer and post-processing, everything else is almost a
copy/paste.
Instead of adding a forth copy/pasted-ish code when adding
the passthrough VPD BL emulation, this patch extirpates
this repetition of those 3 functions and put it into
a new one called scsi_SG_IO_FROM_DEV. Any future code that
wants to execute an SG_DXFER_FROM_DEV to the device can
use it, avoiding filling sg_io_hdr_t again and et cetera.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-3-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To add support for the emulation of Block Limits VPD page
for passthrough devices, a few adjustments in the current code
base is required to avoid repetition and improve clarity.
In scsi-generic.c, detach the Inquiry handling from
scsi_read_complete and put it into a new function called
scsi_handle_inquiry_reply. This change aims to avoid
cluttering of scsi_read_complete when we more logic in the
Inquiry response handling is added in the next patches,
centralizing the changes in the new function.
In scsi-disk.c, take the build of all emulated VPD pages
from scsi_disk_emulate_inquiry and make it available to
other files into a non-static function called
scsi_disk_emulate_vpd_page. Making it public will allow
the future VPD BL emulation code for passthrough devices
to use it from scsi-generic.c, avoiding copy/pasting this
code solely for that purpose. It also has the advantage of
providing emulation of all VPD pages in case we need to
emulate other pages in other scenarios. As a bonus,
scsi_disk_emulate_inquiry got tidier.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-2-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the legacy esp_init() function now that there are no more remaining
users.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180613094727.11326-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
The preferred way to select the KVM accelerator is to use "-accel kvm"
these days, so let's be consistent in our documentation and help texts.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1528866321-23886-3-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No reason for vhost-scsi to pull in migration headers directly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is only half of the work, because the proxy devices (virtio-*-pci,
virtio-*-ccw, etc.) are still included unconditionally. It is still a
move in the right direction.
Based-on: <20180522194943.24871-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove those unneeded includes to speed up the compilation
process a little bit.
Code change produced with:
$ git grep '#include "sysemu/blockdev.h"' | \
cut -d: -f-1 | \
xargs egrep -L "(BlockInterfaceType|DriveInfo|drive_get|blk_legacy_dinfo|blockdev_mark_auto_del)" | \
xargs sed -i.bak '/#include "sysemu\/blockdev.h"/d'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-15-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove those unneeded includes to speed up the compilation
process a little bit. (Continue 7eceff5b5a cleanup)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-13-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to the MemoryRegion valid.accepts
callback. We'll need this for subpage_accepts().
We could take the approach we used with the read and write
callbacks and add new a new _with_attrs version, but since there
are so few implementations of the accepts hook we just change
them all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-9-peter.maydell@linaro.org
When multi queue is enabled e.g. for a virtio-net device,
each queue pair will have a vhost_dev, and the only thing
shared between vhost devs currently is the chardev. This
patch introduces a vhost-user state structure which will
be shared by all vhost devs of the same virtio device.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU SCSI code makes assumptions about how the PROTECT and BYTCHK
works in the protocol, denying support for PI (Protection
Information) in case the guest OS requests it. However, in SCSI versions 2
and older, there is no PI concept in the protocol.
This means that when dealing with such devices:
- there is no PROTECT bit in byte 5 of the standard INQUIRY response. The
whole byte is marked as "Reserved";
- there is no RDPROTECT in byte 2 of READ. We have 'Logical Unit Number'
in this field instead;
- there is no VRPROTECT in byte 2 of VERIFY. We have 'Logical Unit Number'
in this field instead. This also means that the BYTCHK bit in this case
is not related to PI.
Since QEMU does not consider these changes, a SCSI passthrough using
a SCSI-2 device will not work. It will mistake these fields with
PI information and return Illegal Request SCSI SENSE thinking
that the driver is asking for PI support.
This patch fixes it by adding a new attribute called 'scsi_version'
that is read from the standard INQUIRY response of passthrough
devices. This allows for a version verification before applying
conditions related to PI that doesn't apply for older versions.
Reported-by: Dac Nguyen <dacng@us.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Message-Id: <20180327211451.14647-1-danielhb@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We would like to have different behavior for passthrough devices
depending on the SCSI version they expose. To prepare for that,
allow the user of emulated devices to specify the desired SCSI
level, and adjust the emulation according to the property value.
The next patch will set the level for scsi-block and scsi-generic
devices.
Based on a patch by Daniel Henrique Barboza
<danielhb@linux.vnet.ibm.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some backends report big max_io_sectors. Making min_io_size the same
value in this case will make it impossible for guest to align memory,
therefore the disk may not be usable at all.
Do not enlarge them when they are zero.
Reported-by: David Gibson <dgibson@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180327164141.19075-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
