Callers of dma_blk_io have no way to pass extra data to the DMAIOFunc,
because the original callback and opaque are gone by the time DMAIOFunc
is called. On the other hand, the BlockBackend is usually derived
from those extra data that you could pass to the DMAIOFunc (in the
next patch, that would be the SCSIRequest).
So change DMAIOFunc's prototype, decoupling it from blk_aio_readv
and blk_aio_writev's. The new prototype loses the BlockBackend
and gains an extra opaque value which, in the case of dma_blk_readv
and dma_blk_writev, is of course used for the BlockBackend.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based blk_aio_readv() and blk_aio_writev() should die; switch
to byte-based blk_aio_preadv() and blk_aio_pwritev() instead.
The patch had to touch multiple files at once, because dma_blk_io()
takes pointers to the functions, and ide_issue_trim() piggybacks on
the same interface (while ignoring offset under the hood).
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Restart of ATAPI DMA used to be unreachable, because the request to do
so wasn't indicated in bus->error_status due to the lack of spare bits, and
ide_restart_bh() would return early doing nothing.
This patch makes use of the observation that not all bit combinations were
possible in ->error_status. In particular, IDE_RETRY_READ only made sense
together with IDE_RETRY_DMA or IDE_RETRY_PIO. This allows to re-use
IDE_RETRY_READ alone as an indicator of ATAPI DMA restart request.
To makes things more uniform, ATAPI DMA gets its own value for ->dma_cmd.
As a means against confusion, macros are added to test the state of
->error_status.
The patch fixes the restart of both in-flight and pending ATAPI DMA,
following the scheme similar to that of IDE DMA.
[Including a fixup patch:
Message-id: 1460465594-15777-1-git-send-email-pbutsykin@virtuozzo.com
--js]
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1459924806-306-4-git-send-email-den@openvz.org
Signed-off-by: John Snow <jsnow@redhat.com>
If the migration occurs after the IDE DMA has been set up but before it
has been initiated, the state gets lost upon save/restore. Specifically,
->dma_cb callback gets cleared, so, when the guest eventually starts bus
mastering, the DMA never completes, causing the guest to time out the
operation.
OTOH all the infrastructure is already in place to restart the DMA if
the migration happens while the DMA is in progress.
So reuse that infrastructure, by setting bus->error_status based on
->dma_cmd in pre_save if ->dma_cb callback is already set but DMAING is
clear. This will indicate the need for restart and make sure ->dma_cb
is restored in ide_restart_bh(); howeover since DMAING is clear the state
upon restore will be exactly "ready for DMA" as before the save.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1459924806-306-2-git-send-email-den@openvz.org
Signed-off-by: John Snow <jsnow@redhat.com>
Buffered DMA cancellation was added to ATAPI devices and implemented
for the BMDMA HBA. Move the code over to common IDE code and allow
it to be used for any HBA.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-4-git-send-email-jsnow@redhat.com
this patch adds a new aio readv compatible function which copies
all data through a bounce buffer. These buffered requests can be
flagged as orphaned which means that their original callback has
already been invoked and the request has just not been completed
by the backend storage. The bounce buffer guarantees that guest
memory corruption is avoided when such a orphaned request is
completed by the backend at a later stage.
This trick only works for read requests as a write request completed
at a later stage might corrupt data as there is no way to control
if and what data has already been written to the storage.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1447345846-15624-4-git-send-email-pl@kamp.de
Signed-off-by: John Snow <jsnow@redhat.com>
Not that you can request a >2GiB transaction, but that's why checking
for it makes no sense anymore.
With the newer 'limit' parameter to prepare_buf, we no longer need a
static limit. The maximum limit is still 2GiB, but the limit parameter
is set to the current transaction size, which cannot surpass 32MiB
(512 * 65536). If the PRDT surpasses the transactional size, then,
we'll just carry out the normative underflow handling pathways instead
of needing an extra, strange pathway that worries about hitting some
logistical cap for the largest sglist we can support -- we'll never
even attempt to build one that big anymore.
Reported-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1445902682-20051-1-git-send-email-jsnow@redhat.com
We're supposed to abort on transfers like this, unless we fill
Word 125 of our IDENTIFY data with a default transfer size, which
we don't currently do.
This is an ATA error, not a SCSI/ATAPI one.
See ATA8-ACS3 sections 7.17.6.49 or 7.21.5.
If we don't do this, QEMU will loop forever trying to transfer
zero bytes, which isn't particularly useful.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1442253685-23349-2-git-send-email-jsnow@redhat.com
IDEState's io_buffer_offset was originally added to keep track of offsets
in AHCI rather exclusively, but it was added to IDEState instead of an
AHCI-specific structure.
AHCI fakes all PIO transfers using DMA and a scatter-gather list. When
the core or atapi layers invoke HBA-specific mechanisms for transfers,
they do not always know that it is being backed by DMA or a sglist, so
this offset is not always updated by the HBA code everywhere.
If we modify it in dma_buf_commit, however, any HBA that needs to use
this offset to manage operating on only part of a sglist will have
access to it.
This will fix ATAPI PIO transfers performed through the AHCI HBA,
which were previously not modifying this value appropriately.
This will fix ATAPI PIO transfers larger than one sector.
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1440546331-29087-2-git-send-email-jsnow@redhat.com
CC: qemu-stable@nongnu.org
Handle NCQ failures for cases where we want to halt the VM on IO errors.
Upon a VM state change, retry the halted NCQ commands.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-7-git-send-email-jsnow@redhat.com
prepare_buf should not always grab as many descriptors
as it can, sometimes it should self-limit.
For example, an NCQ transfer of 1 sector with a PRDT that
describes 4GiB of data should not copy 4GiB of data, it
should just transfer that first 512 bytes.
PIO is not affected, because the dma_buf_rw dma helpers
already have a byte limit built-in to them, but DMA/NCQ
will exhaust the entire list regardless of requested size.
AHCI 1.3 specifies in section 6.1.6 Command List Underflow that
NCQ is not required to detect underflow conditions. Non-NCQ
pathways signal underflow by writing to the PRDBC field, which
will already occur by writing the actual transferred byte count
to the PRDBC, signaling the underflow.
Our NCQ pathways aren't required to detect underflow, but since our DMA
backend uses the size of the PRDT to determine the size of the transer,
if our PRDT is bigger than the transaction (the underflow condition) it
doesn't cost us anything to detect it and truncate the PRDT.
This is a recoverable error and is not signaled to the guest, in either
NCQ or normal DMA cases.
For BMDMA, the existing pathways should see no guest-visible difference,
but any bytes described in the overage will no longer be transferred
before indicating to the guest that there was an underflow.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-2-git-send-email-jsnow@redhat.com
Amazingly, we weren't doing this before.
Make sure we migrate the IDEState structure that belongs to
the AHCIDevice.IDEBus structure during migrations.
No version numbering changes because AHCI is not officially
migratable (and we can all see with good reason why) so we
do not impact any official builds by altering the stream and
leaving it at version 1.
This fixes the rerror=stop/werror=stop test case where we wish
to migrate a halted job. Previously, the error code would not
migrate, so even if the job completed successfully, AHCI would
report an error because it would still have the placeholder
error code from initialization time.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-15-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-13-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This moves more common restarting logic to the core IDE code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-10-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Start moving the initial state of the current request to IDEBus, so that
AHCI can use it. The set_unit callback is not used anymore once this is
done.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-9-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With restarts now handled by ide_restart_cb and
the IDEDMAOps.restart_dma() member, remove the old
restart_cb callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-8-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With BMDMA specific excised from the restart functions,
create a HBA-agnostic restart callback to be shared
between the different HBAs.
Change the callback registered with the vmstate_change
handler to always point to ide_restart_cb instead of
relying on the IDEDMAOps.restart_cb() member.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-7-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A helper is added that registers the IDEDMAOp .restart_cb()
via qemu_add_vm_change_state_handler instead of requiring
each HBA to register the callback themselves.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the restart_dma callback and adjusts
the ide_restart_dma function to utilize this callback
to call the BMDMA-specific restart code instead of statically
executing BMDMA-specific code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(With the previous atapi_dma flag recovery)
If migration happens between the ATAPI command being written and the
bmdma being started, the DMA is dropped. Eventually the guest times
out and recovers, but that can take many seconds.
(This is rare, on a pingpong reading the CD continuously I hit
this about ~1/30-1/50 migrates)
I don't think we've got enough state to be able to recover safely
at this point, so I throw a 'medium error, no seek complete'
that I'm assuming guests will try and recover from an apparently
dirty CD.
OK, it's a hack, the real solution is probably to push a lot of
ATAPI state into the migration stream, but this is a fix that
works with no stream changes. Tested only on Linux (both RHEL5
(pre-libata) and RHEL7).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
SCSI devices have multiple kinds of queries they need to respond
to, as defined in the "cmd inquiry" section in MMC-6 and SPC-3.
Relevent sections:
MMC-6 revision 2g:
Non-VPD response data and pointer to SPC-3;
Section 6.8 "Inquiry Command"
SPC-3 revision 23:
Inquiry command and error handling:
Section 6.4 "INQUIRY command"
VPD data pages format:
Section 7.6 "Vital product data parameters"
We implement these Vital Product Data queries for SCSI, but not for
ATAPI through IDE. The result is that if you are looking for the WWN
identifier via tools such as sg3_utils, you will be unable to query
our CD/DVD rom device to obtain it.
This patch adds the minimum number of mandatory responses as defined
by SPC-3, which include the "supported pages" response (page 0x00)
and the "Device Identification" response (page 0x83). It also correctly
responds when it receives a request for an illegal page to improve
error output from related tools.
The Device ID page contains an arbitrary list of identification
strings of various formats; the ID strings included in this patch
were chosen to mimic those provided by the libata driver when
emulating this SCSI query (model, serial, and wwn when present.)
Example:
# libata emulated response
[root@localhost ~]# sg_inq --id /dev/sda
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: vendor specific [0x0], code_set: ASCII
associated with the addressed logical unit
vendor specific: QM00001
Designation descriptor number 2, descriptor length: 72
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: ATA
vendor specific: QEMU HARDDISK QM00001
# QEMU generated ATAPI response, with WWN
[root@localhost ~]# sg_inq --id /dev/sr0
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: vendor specific [0x0], code_set: ASCII
associated with the addressed logical unit
vendor specific: QM00005
Designation descriptor number 2, descriptor length: 72
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: ATA
vendor specific: QEMU DVD-ROM QM00005
Designation descriptor number 3, descriptor length: 12
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 5, IEEE Company_id: 0xc50
Vendor Specific Identifier: 0x15ea71bb
[0x5000c50015ea71bb]
See also: hw/scsi/scsi-disk.c, scsi_disk_emulate_inquiry()
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This impacts both BMDMA and AHCI HBA interfaces for IDE.
Currently, we confuse the difference between a PRDT having
"0 bytes" and a PRDT having "0 complete sectors."
When we receive an incomplete sector, inconsistent error checking
leads to an infinite loop wherein the call succeeds, but it
didn't give us enough bytes -- leading us to re-call the
DMA chain over and over again. This leads to, in the BMDMA case,
leaked memory for short PRDTs, and infinite loops and resource
usage in the AHCI case.
The .prepare_buf() callback is reworked to return the number of
bytes that it successfully prepared. 0 is a valid, non-error
answer that means the table was empty and described no bytes.
-1 indicates an error.
Our current implementation uses the io_buffer in IDEState to
ultimately describe the size of a prepared scatter-gather list.
Even though the AHCI PRDT/SGList can be as large as 256GiB, the
AHCI command header limits transactions to just 4GiB. ATA8-ACS3,
however, defines the largest transaction to be an LBA48 command
that transfers 65,536 sectors. With a 512 byte sector size, this
is just 32MiB.
Since our current state structures use the int type to describe
the size of the buffer, and this state is migrated as int32, we
are limited to describing 2GiB buffer sizes unless we change the
migration protocol.
For this reason, this patch begins to unify the assertions in the
IDE pathways that the scatter-gather list provided by either the
AHCI PRDT or the PCI BMDMA PRDs can only describe, at a maximum,
2GiB. This should be resilient enough unless we need a sector
size that exceeds 32KiB.
Further, the likelihood of any guest operating system actually
attempting to transfer this much data in a single operation is
very slim.
To this end, the IDEState variables have been updated to more
explicitly clarify our maximum supported size. Callers to the
prepare_buf callback have been reworked to understand the new
return code, and all versions of the prepare_buf callback have
been adjusted accordingly.
Lastly, the ahci_populate_sglist helper, relied upon by the
AHCI implementation of .prepare_buf() as well as the PCI
implementation of the callback have had overflow assertions
added to help make clear the reasonings behind the various
type changes.
[Added %d -> %"PRId64" fix John sent because off_pos changed from int to
int64_t.
--Stefan]
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, DMA read/write operations neglect to update
the byte count after a successful transfer like ATAPI
DMA read or PIO read/write operations do.
We correct this oversight by adding another callback into
the IDEDMAOps structure. The commit callback is called
whenever we are cleaning up a scatter-gather list.
AHCI can register this callback in order to update post-
transfer information such as byte count updates.
We use this callback in AHCI to consolidate where we delete
the SGlist as generated from the PRDT, as well as update the
byte count after the transfer is complete.
The QEMUSGList structure has an init flag added to it in order
to make qemu_sglist_destroy a nop if it is called when
there is no sglist, which simplifies cleanup and error paths.
This patch fixes several AHCI problems, notably Non-NCQ modes
of operation for Windows 7 as well as Hibernate support for Windows 7.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412204151-18117-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use it with block backends shortly, and the name is going to fit
badly there. It's a block layer thing anyway, not just a block driver
thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use BlockDriverAIOCB with block backends shortly, and the name is
going to fit badly there. It's a block layer thing anyway, not just a
block driver thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
AHCI has code to fill in the D2H FIS trigger the IRQ all over the place.
Centralize this in a single cmd_done callback by generalizing the existing
async_cmd_done callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
They are not used by AHCI, and should not be even available there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is now called only after the set_inactive callback. Put the two together.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Make it optional and prepare for the next patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
AHCI couldn't cope with asynchronous commands that aren't doing DMA, it
simply wouldn't complete them. Due to the bug fixed in commit f68ec837,
FLUSH commands would seem to have completed immediately even if they
were still running on the host. After the commit, they would simply hang
and never unset the BSY bit, rendering AHCI unusable on any OS sending
flushes.
This patch adds another callback for the completion of asynchronous
commands. This is what AHCI really wants to use for its command
completion logic rather than an DMA completion callback.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
An IDE bus provided by AHCI can only take a single IDE drive. If you add
a drive as slave, qemu used to accept the command line but the device
wouldn't be actually usable. Catch the situation instead and error out.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Headers in include/exec/ are for the deepest innards of QEMU,
they should almost never be included directly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it necessary to compile these files per-target.
However, fixing this does not belong in these patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While testing q35, which has its cdrom attached to the ahci controller, I found
that the Fedora 17 install would panic on boot. The panic occurs while
squashfs is trying to read from the cdrom. The errors are:
[ 8.622711] SQUASHFS error: xz_dec_run error, data probably corrupt
[ 8.625180] SQUASHFS error: squashfs_read_data failed to read block
0x20be48a
I was also able to produce corrupt data reads using an installed piix based
qemu machine, using 'dd'. I found that the corruptions were only occuring when
then read size was greater than 128k. For example, the following command
results in corrupted reads:
dd if=/dev/sr0 of=/tmp/blah bs=256k iflag=direct
The > 128k size reads exercise a different code path than 128k and below. In
ide_atapi_cmd_read_dma_cb() s->io_buffer_size is capped at 128k. Thus,
ide_atapi_cmd_read_dma_cb() is called a second time when the read is > 128k.
However, ahci_dma_rw_buf() restart the read from offset 0, instead of at 128k.
Thus, resulting in a corrupted read.
To fix this, I've introduced 'io_buffer_offset' field in IDEState to keep
track of the offset. I've also modified ahci_populate_sglist() to take a new
3rd offset argument, so that the sglist is property initialized.
I've tested this patch using 'dd' testing, and Fedora 17 now correctly boots
and installs on q35 with the cdrom ahci controller.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This stuff doesn't belong to block layer, and was put there only
because a better home didn't exist then. Now it does.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This isn't quite orthodox. CHS translation is firmware configuration,
communicated via the RTC's CMOS RAM, not a property of the disk. But
it's best to treat it just like geometry anyway.
Maintain backward compatibility exactly like for geometry: fall back
to DriveInfo's translation, set with -drive trans=...
Bonus: info qtree now shows the translation. Except when it shows
"auto": that's resolved by pc_cmos_init_late(). To be addressed
shortly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Geometry needs to be qdev properties, because it belongs to the
disk's guest part.
Maintain backward compatibility exactly like for serial: fall back to
DriveInfo's geometry, set with -drive cyls=...
Do this only for ide-hd. ide-drive is legacy. ide-cd doesn't have a
geometry.
Bonus: info qtree now shows the geometry.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
PC BIOS setup needs IDE geometry information. Get it directly from
the device model rather than through the block layer. In preparation
of purging geometry from the block layer, which will happen later in
this series.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is far less interesting than it sounds. We simply add an Object to each
BusState and then register the types appropriately. Most of the interesting
refactoring will follow in the next patches.
Since we're changing fundamental type names (BusInfo -> BusClass), it all needs
to convert at once. Fortunately, not a lot of code is affected.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[AF: Made all new bus TypeInfos static const.]
[AF: Made qbus_free() call object_delete(), required {qom,glib}_allocated]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The IDE PIO interface currently uses bdrv_read() to perform reads
synchronously. Synchronous I/O in the vcpu thread is bad because it
prevents the guest from executing code - it makes the guest
unresponsive.
This patch converts IDE PIO to use bdrv_aio_readv(). We simply need to
use the BUSY_STAT status so the guest knows to wait while we are busy.
The only external user of ide_sector_read() is restart behavior on I/O
errors and it is not affected by this change. We still need to restart
I/O in the same way.
Migration is also unaffected if I understand the code correctly. We
continue to use the same transfer function and the BUSY_STAT status
should never be migrated since we flush I/O before migrating device
state.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Tested-by: Richard Davies <richard@arachsys.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
