pl011_luminary_create() is only used for the Stellaris board,
open-code it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230220115114.25237-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pl011_create() is only used in DeviceRealize handlers,
not a hot-path. Inlining is not justified.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230220115114.25237-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PL011 can be in either of 2 modes depending guest config: FIFO and
single register. The last mode could be viewed as a 1-element-deep FIFO.
Current code open-codes a bunch of depth-dependent logic. Refactor FIFO
depth handling code to isolate calculating current FIFO depth.
One functional (albeit guest-invisible) side-effect of this change is
that previously we would always increment s->read_pos in UARTDR read
handler even if FIFO was disabled, now we are limiting read_pos to not
exceed FIFO depth (read_pos itself is reset to 0 if user disables FIFO).
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230123162304.26254-2-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A clock is added by commit aac63e0e6e ("hw/char/pl011: add a clock
input") since v5.2.0 which corresponds to virt-5.2 machine type. It
causes backwards migration failure from upstream to downstream (v5.1.0)
when the machine type is specified with virt-5.1.
This fixes the issue by following instructions from section "Connecting
subsections to properties" in docs/devel/migration.rst. With this applied,
the PL011 clock is migrated based on the machine type.
virt-5.2 or newer: migration
virt-5.1 or older: non-migration
Cc: qemu-stable@nongnu.org # v5.2.0+
Fixes: aac63e0e6e ("hw/char/pl011: add a clock input")
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20210318023801.18287-1-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a clock input to the PL011 UART so we can compute the current baud
rate and trace it. This is intended for developers who wish to use QEMU
to e.g. debug their firmware or to figure out the baud rate configured
by an unknown/closed source binary.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
The PL011 UART has six interrupt lines:
* RX (receive data)
* TX (transmit data)
* RT (receive timeout)
* MS (modem status)
* E (errors)
* combined (logical OR of all the above)
So far we have only emulated the combined interrupt line;
add support for the others, so that boards that wire them
up to different interrupt controller inputs can do so.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl011's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Header guard symbols should match their file name to make guard
collisions less likely. Offenders found with
scripts/clean-header-guards.pl -vn.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
* drop qemu_char_get_next_serial and use chardev prop
* add pl011_create wrapper function to create pl011 uart device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-2-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
