The sun4u machine has an IOMMU and therefore it is possible to program it such
that the virtio-device IOVA does not map directly to the CPU physical address.
This is not a problem with Linux which always maps the IOVA directly to the CPU
physical address, however it is required for the NetBSD virtio driver where this
is not the case.
Set the sun4u machine defaults for all virtio devices so that disable-legacy=on
and iommu_platform=on to ensure a default configuration will allow virtio
devices to function correctly on both Linux and NetBSD.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20240418205730.31396-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
During kernel startup OpenBSD accesses addresses mapped by BAR0 of the ebus device
but at offsets where no IO devices exist. Before commit 4aa07e8649 ("hw/sparc64/ebus:
Access memory regions via pci_address_space_io()") BAR0 was mapped to legacy IO
space which allows accesses to unmapped devices to succeed, but afterwards these
accesses to unmapped PCI IO space cause a memory fault which prevents OpenBSD from
booting.
Since no devices are mapped at the addresses accessed by OpenBSD, change ebus BAR0
from a PCI IO space alias to an IO memory region using unassigned_io_ops which allows
these accesses to succeed and so allows OpenBSD to boot once again.
Fixes: 4aa07e8649 ("hw/sparc64/ebus: Access memory regions via pci_address_space_io()")
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240311064345.2531197-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The first sunhme NIC gets placed a function 1 on slot 1 of PCI bus A,
and the rest are dynamically assigned on PCI bus B.
Previously, any PCI NIC would get the special treatment purely by
virtue of being first in the list.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
PCI functions are plugged on a PCI bus. They can only access
external memory regions via the bus.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231011185954.10337-5-philmd@linaro.org>
There is also pci_new() which creates non-multifunction PCI devices.
Accordingly the parameter is always set to true when a multi function PCI
device is to be created.
The reason for the parameter's existence seems to be that it is used in the
internal PCI code as well which is the only location where it gets set to
false. This one usage can be resolved by factoring out an internal helper
function.
Remove this redundant, error-prone parameter.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230304114043.121024-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allows the struct to be embedded directly into device models without additional
allocation.
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230612081238.1742-3-shentey@gmail.com>
[PMD: Update MAINTAINERS entry and use SPDX license identifier]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Announce the default NIC via MachineClass->default_nic and set up
MachineClass->no_parallel according to the availability of the
"isa-parallel" device, so that the Sun machines also work when
QEMU has been configured with "--without-default-devices".
Message-Id: <20230512124033.502654-11-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch provides accessor functions as replacements for direct
access to slot_reserved_mask according to the comment at the top
of include/hw/pci/pci_bus.h which advises that data structures for
PCIBus should not be directly accessed but instead be accessed using
accessor functions in pci.h.
Three accessor functions can conveniently replace all direct accesses
of slot_reserved_mask. With this patch, the new accessor functions are
used in hw/sparc64/sun4u.c and hw/xen/xen_pt.c and pci_bus.h is removed
from the included header files of the same two files.
No functional change intended.
Signed-off-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <b1b7f134883cbc83e455abbe5ee225c71aa0e8d0.1678888385.git.brchuckz@aol.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> [sun4u]
Only include "hw/irq.h" where appropriate.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-10-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
isa_bus_irqs() register an array of input IRQs on
the ISA bus. Rename it as isa_bus_register_input_irqs().
Mechanical change using:
$ sed -i -e 's/isa_bus_irqs/isa_bus_register_input_irqs/g' \
$(git grep -wl isa_bus_irqs)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-10-philmd@linaro.org>
Keep reference to ISA input IRQs in EbusState.
To emphasize input/output distinction, rename arrays
as isa_irqs_in / isa_irqs_out.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-7-philmd@linaro.org>
Several machines have an unused MAX_IDE_BUS define. Remove it from
these machines that don't need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220917115136.A32EF746E06@zero.eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
TYPE_I8042 is exported, so reuse it for consistency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220520180109.8224-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
As part of converting -boot to a property with a QAPI type, define
the struct and use it throughout QEMU to access boot configuration.
machine_boot_parse takes care of doing the QemuOpts->QAPI conversion by
hand, for now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220414165300.555321-2-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A global boolean variable "vga_interface_created"(declared in softmmu/globals.c)
has been used to track the creation of vga interface. If the vga flag is passed
in the command line "default_vga"(declared in softmmu/vl.c) variable is set to 0.
To warn user, the condition checks if vga_interface_created is false
and default_vga is equal to 0. If "-vga none" is passed, this patch will not warn the
user regarding the creation of VGA device.
The warning "A -vga option was passed but this
machine type does not use that option; no VGA device has been created"
is logged if vga flag is passed but no vga device is created.
This patch has been tested for x86_64, i386, sparc, sparc64 and arm boards.
Signed-off-by: Gautam Agrawal <gautamnagrawal@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/581
Message-Id: <20220501122505.29202-1-gautamnagrawal@gmail.com>
[thuth: Fix wrong warning with "-device" in some cases as reported by Paolo]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The 'ide-hd' and 'ide-cd' devices provide suitable alternatives.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201026143028.3034018-15-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The device should not map itself but instead should be mapped to sysbus by the
sun4u machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200926140216.7368-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200902224311.1321159-49-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Since commit 61f20b9dc5 ("spapr_nvram: Pre-initialize the NVRAM to
support the -prom-env parameter"), pseries machines can pre-initialize
the "system" partition in the NVRAM with the data passed to all -prom-env
parameters on the QEMU command line.
In this case it is assumed that all the data fits in 64 KiB, but the user
can easily pass more and crash QEMU:
$ qemu-system-ppc64 -M pseries $(for ((x=0;x<128;x++)); do \
echo -n " -prom-env " ; printf "%0.sx" {1..1024}; \
done) # this requires ~128 Kib
malloc(): corrupted top size
Aborted (core dumped)
This happens because we don't check if all the prom-env data fits in
the NVRAM and chrp_nvram_set_var() happily memcpy() it passed the
buffer.
This crash affects basically all ppc/ppc64 machine types that use -prom-env:
- pseries (all versions)
- g3beige
- mac99
and also sparc/sparc64 machine types:
- LX
- SPARCClassic
- SPARCbook
- SS-10
- SS-20
- SS-4
- SS-5
- SS-600MP
- Voyager
- sun4u
- sun4v
Add a max_len argument to chrp_nvram_create_system_partition() so that
it can check the available size before writing to memory.
Since NVRAM is populated at machine init, it seems reasonable to consider
this error as fatal. So, instead of reporting an error when we detect that
the NVRAM is too small and adapt all machine types to handle it, we simply
exit QEMU in all cases. This is still better than crashing. If someone
wants another behavior, I guess this can be reworked later.
Tested with:
$ yes q | \
(for arch in ppc ppc64 sparc sparc64; do \
echo == $arch ==; \
qemu=${arch}-softmmu/qemu-system-$arch; \
for mach in $($qemu -M help | awk '! /^Supported/ { print $1 }'); do \
echo $mach; \
$qemu -M $mach -monitor stdio -nodefaults -nographic \
$(for ((x=0;x<128;x++)); do \
echo -n " -prom-env " ; printf "%0.sx" {1..1024}; \
done) >/dev/null; \
done; echo; \
done)
Without the patch, affected machine types cause QEMU to report some
memory corruption and crash:
malloc(): corrupted top size
free(): invalid size
*** stack smashing detected ***: terminated
With the patch, QEMU prints the following message and exits:
NVRAM is too small. Try to pass less data to -prom-env
It seems that the conditions for the crash have always existed, but it
affects pseries, the machine type I care for, since commit 61f20b9dc5
only.
Fixes: 61f20b9dc5 ("spapr_nvram: Pre-initialize the NVRAM to support the -prom-env parameter")
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1867739
Reported-by: John Snow <jsnow@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159736033937.350502.12402444542194031035.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
The floppy controller devices desugar their drive properties into
floppy devices (since commit a92bd191a4 "fdc: Move qdev properties to
FloppyDrive", v2.8.0). This involves some bad magic in
fdctrl_connect_drives(), and exists for backward compatibility.
The functions for boards to create floppy controller devices
fdctrl_init_isa(), fdctrl_init_sysbus(), and sun4m_fdctrl_init()
desugar -drive if=floppy to these floppy controller drive properties.
If you use both -drive if=floppy (or its -fda / -fdb sugar) and
-global isa-fdc for the same floppy device, -global silently loses the
conflict, and both backends involved end up with the floppy device
frontend attached, as demonstrated by iotest 172 (see commit before
previous). This is wrong.
Desugar -drive if=floppy straight to floppy devices instead, with
helper fdctrl_init_drives(). The conflict now gets rejected cleanly:
first, fdctrl_connect_drives() creates the floppy for the controller's
property, then fdctrl_init_drives() attempts to create the floppy for
-drive if=floppy, but fails because the unit is already in use.
Output of iotest 172 changes in three ways:
1. The clash gets rejected.
2. In one test case, "info qtree" has the floppy devices swapped, and
"info block" has their QOM paths swapped. This is because the
floppy device for -fda now gets created after the one for -global
isa-fdc.driveB.
3. The error message for -global floppy.drive=floppy0 changes. Before
the patch, we set isa-fdc.driveA to -fda's block backend, then
create the floppy device for it, then move the backend from
isa-fdc.driveA to floppy.drive. Floppy creation fails when
applying -global floppy.drive=floppy0, because floppy0 is still
attached to isa-fdc. After the patch, we create the floppy for
-fda, then set its drive property to floppy0. Now floppy creation
succeeds, but setting the drive property fails, because -global
already set it. Yes, this is exasperatingly complicated.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-5-armbru@redhat.com>
Same transformation as in the previous commit. Manual, because
convincing Coccinelle to transform these cases is not worthwhile.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-17-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
The pci_ide_create_devs() function takes a hd_table parameter but all
callers just pass what ide_drive_get() returns so we can do it locally
simplifying callers and removing hd_table parameter.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: e9713fdded4d212fa68ed03b844e531934226a6f.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
There's no good reason for it to be type int, change it to bool.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200207161948.15972-3-philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
While loading the executable, some platforms (like AVR) need to
detect CPU type that executable is built for - and, with this patch,
this is enabled by reading the field 'e_flags' of the ELF header of
the executable in question. The change expands functionality of
the following functions:
- load_elf()
- load_elf_as()
- load_elf_ram()
- load_elf_ram_sym()
The argument added to these functions is called 'pflags' and is of
type 'uint32_t*' (that matches 'pointer to 'elf_word'', 'elf_word'
being the type of the field 'e_flags', in both 32-bit and 64-bit
variants of ELF header). Callers are allowed to pass NULL as that
argument, and in such case no lookup to the field 'e_flags' will
happen, and no information will be returned, of course.
CC: Richard Henderson <rth@twiddle.net>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Edgar E. Iglesias <edgar.iglesias@gmail.com>
CC: Michael Walle <michael@walle.cc>
CC: Thomas Huth <huth@tuxfamily.org>
CC: Laurent Vivier <laurent@vivier.eu>
CC: Philippe Mathieu-Daudé <f4bug@amsat.org>
CC: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
CC: Aurelien Jarno <aurelien@aurel32.net>
CC: Jia Liu <proljc@gmail.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: BALATON Zoltan <balaton@eik.bme.hu>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Artyom Tarasenko <atar4qemu@gmail.com>
CC: Fabien Chouteau <chouteau@adacore.com>
CC: KONRAD Frederic <frederic.konrad@adacore.com>
CC: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
Signed-off-by: Michael Rolnik <mrolnik@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1580079311-20447-24-git-send-email-aleksandar.markovic@rt-rk.com>
The M48T59 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-5-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The global smp variables in alpha/hppa/mips/openrisc/sparc*/xtensa codes
are replaced with smp properties from MachineState.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-10-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Implement fw_cfg_arch_key_name(), which returns the name of a
sparc64-specific key.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190422195020.1494-8-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The sun4uv_init() function expects vga_interface_type to be either
VGA_STD or VGA_NONE and sets up a stdvga device or no vga card
accordingly.
However, the code in vl.c prefers the Cirrus VGA card to stdvga if
it is available and the user and the machine did not specify anything
else.
So far this has not been a problem, since the Cirrus VGA was not linked
into the sparc64 target. But with the upcoming Kconfig build system,
all theoretically possible PCI cards will be enabled by default, so the
Cirrus VGA card might become available on the sparc64 target, too. vl.c
then picks the wrong card, causing sun4uv_init() to abort.
Thus let's make it explicit that we always want stdvga for sparc64 and
so set default_display = "std" for these machines.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <1550041639-10232-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
