In arm_v7m_mmu_idx_for_secstate() we get the 'priv' level to pass to
armv7m_mmu_idx_for_secstate_and_priv() by calling arm_current_el().
This is incorrect when the security state being queried is not the
current one, because arm_current_el() uses the current security state
to determine which of the banked CONTROL.nPRIV bits to look at.
The effect was that if (for instance) Secure state was in privileged
mode but Non-Secure was not then we would return the wrong MMU index.
The only places where we are using this function in a way that could
trigger this bug are for the stack loads during a v8M function-return
and for the instruction fetch of a v8M SG insn.
Fix the bug by expanding out the M-profile version of the
arm_current_el() logic inline so it can use the passed in secstate
rather than env->v7m.secure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201022164408.13214-1-peter.maydell@linaro.org
Secure mode is not exempted from checking SCR_EL3.TLOR, and in the
future HCR_EL2.TLOR when S-EL2 is enabled.
Signed-off-by: Rémi Denis-Courmont <remi.denis.courmont@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
HCR should be applied when NS is set, not when it is cleared.
Signed-off-by: Rémi Denis-Courmont <remi.denis.courmont@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The helper functions for performing the udot/sdot operations against
a scalar were not using an address-swizzling macro when converting
the index of the scalar element into a pointer into the vm array.
This had no effect on little-endian hosts but meant we generated
incorrect results on big-endian hosts.
For these insns, the index is indexing over group of 4 8-bit values,
so 32 bits per indexed entity, and H4() is therefore what we want.
(For Neon the only possible input indexes are 0 and 1.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201028191712.4910-3-peter.maydell@linaro.org
In the neon_padd/pmax/pmin helpers for float16, a cut-and-paste error
meant we were using the H4() address swizzler macro rather than the
H2() which is required for 2-byte data. This had no effect on
little-endian hosts but meant we put the result data into the
destination Dreg in the wrong order on big-endian hosts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201028191712.4910-2-peter.maydell@linaro.org
We can use proper widening loads to extend 32-bit inputs,
and skip the "widenfn" step.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-12-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In both cases, we can sink the write-back and perform
the accumulate into the normal destination temps.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-11-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only uses of this function are for loading VFP
double-precision values, and nothing to do with NEON.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-10-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace all uses of neon_load/store_reg64 within translate-neon.c.inc.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-9-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only uses of this function are for loading VFP
single-precision values, and nothing to do with NEON.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-8-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can then use this to improve VMOV (scalar to gp) and
VMOV (gp to scalar) so that we simply perform the memory
operation that we wanted, rather than inserting or
extracting from a 32-bit quantity.
These were the last uses of neon_load/store_reg, so remove them.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-7-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Model these off the aa64 read/write_vec_element functions.
Use it within translate-neon.c.inc. The new functions do
not allocate or free temps, so this rearranges the calling
code a bit.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-6-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This seems a bit more readable than using offsetof CPU_DoubleU.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are the only users of neon_reg_offset, so remove that.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will shortly have users outside of translate-neon.c.inc.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function makes it clear that we're talking about the whole
register, and not the 32-bit piece at index 0. This fixes a bug
when running on a big-endian host.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Transform the prot bit to a qemu internal page bit, and save
it in the page tables.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the M-profile low-overhead-branch extension is implemented, FPSCR
bits [18:16] are a new field LTPSIZE. If MVE is not implemented
(currently always true for us) then this field always reads as 4 and
ignores writes.
These bits used to be the vector-length field for the old
short-vector extension, so we need to take care that they are not
misinterpreted as setting vec_len. We do this with a rearrangement
of the vfp_set_fpscr() code that deals with vec_len, vec_stride
and also the QC bit; this obviates the need for the M-profile
only masking step that we used to have at the start of the function.
We provide a new field in CPUState for LTPSIZE, even though this
will always be 4, in preparation for MVE, so we don't have to
come back later and split it out of the vfp.xregs[FPSCR] value.
(This state struct field will be saved and restored as part of
the FPSCR value via the vmstate_fpscr in machine.c.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-11-peter.maydell@linaro.org
M-profile CPUs with half-precision floating point support should
be able to write to FPSCR.FZ16, but an M-profile specific masking
of the value at the top of vfp_set_fpscr() currently prevents that.
This is not yet an active bug because we have no M-profile
FP16 CPUs, but needs to be fixed before we can add any.
The bits that the masking is effectively preventing from being
set are the A-profile only short-vector Len and Stride fields,
plus the Neon QC bit. Rearrange the order of the function so
that those fields are handled earlier and only under a suitable
guard; this allows us to drop the M-profile specific masking,
making FZ16 writeable.
This change also makes the QC bit correctly RAZ/WI for older
no-Neon A-profile cores.
This refactoring also paves the way for the low-overhead-branch
LTPSIZE field, which uses some of the bits that are used for
A-profile Stride and Len.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-10-peter.maydell@linaro.org
In arm_cpu_realizefn(), if the CPU has VFP or Neon disabled then we
squash the ID register fields so that we don't advertise it to the
guest. This code was written for A-profile and needs some tweaks to
work correctly on M-profile:
* A-profile only fields should not be zeroed on M-profile:
- MVFR0.FPSHVEC,FPTRAP
- MVFR1.SIMDLS,SIMDINT,SIMDSP,SIMDHP
- MVFR2.SIMDMISC
* M-profile only fields should be zeroed on M-profile:
- MVFR1.FP16
In particular, because MVFR1.SIMDHP on A-profile is the same field as
MVFR1.FP16 on M-profile this code was incorrectly disabling FP16
support on an M-profile CPU (where has_neon is always false). This
isn't a visible bug yet because we don't have any M-profile CPUs with
FP16 support, but the change is necessary before we introduce any.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-9-peter.maydell@linaro.org
v8.1M's "low-overhead-loop" extension has three instructions
for looping:
* DLS (start of a do-loop)
* WLS (start of a while-loop)
* LE (end of a loop)
The loop-start instructions are both simple operations to start a
loop whose iteration count (if any) is in LR. The loop-end
instruction handles "decrement iteration count and jump back to loop
start"; it also caches the information about the branch back to the
start of the loop to improve performance of the branch on subsequent
iterations.
As with the branch-future instructions, the architecture permits an
implementation to discard the LO_BRANCH_INFO cache at any time, and
QEMU takes the IMPDEF option to never set it in the first place
(equivalent to discarding it immediately), because for us a "real"
implementation would be unnecessary complexity.
(This implementation only provides the simple looping constructs; the
vector extension MVE (Helium) adds some extra variants to handle
looping across vectors. We'll add those later when we implement
MVE.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-8-peter.maydell@linaro.org
v8.1M implements a new 'branch future' feature, which is a
set of instructions that request the CPU to perform a branch
"in the future", when it reaches a particular execution address.
In hardware, the expected implementation is that the information
about the branch location and destination is cached and then
acted upon when execution reaches the specified address.
However the architecture permits an implementation to discard
this cached information at any point, and so guest code must
always include a normal branch insn at the branch point as
a fallback. In particular, an implementation is specifically
permitted to treat all BF insns as NOPs (which is equivalent
to discarding the cached information immediately).
For QEMU, implementing this caching of branch information
would be complicated and would not improve the speed of
execution at all, so we make the IMPDEF choice to implement
all BF insns as NOPs.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-7-peter.maydell@linaro.org
The BLX immediate insn in the Thumb encoding always performs
a switch from Thumb to Arm state. This would be totally useless
in M-profile which has no Arm decoder, and so the instruction
does not exist at all there. Make the encoding UNDEF for M-profile.
(This part of the encoding space is used for the branch-future
and low-overhead-loop insns in v8.1M.)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-6-peter.maydell@linaro.org
The t32 decode has a group which represents a set of insns
which overlap with B_cond_thumb because they have [25:23]=111
(which is an invalid condition code field for the branch insn).
This group is currently defined using the {} overlap-OK syntax,
but it is almost entirely non-overlapping patterns. Switch
it over to use a non-overlapping group.
For this to be valid syntactically, CPS must move into the same
overlapping-group as the hint insns (CPS vs hints was the
only actual use of the overlap facility for the group).
The non-overlapping subgroup for CLREX/DSB/DMB/ISB/SB is no longer
necessary and so we can remove it (promoting those insns to
be members of the parent group).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-5-peter.maydell@linaro.org
From v8.1M, disabled-coprocessor handling changes slightly:
* coprocessors 8, 9, 14 and 15 are also governed by the
cp10 enable bit, like cp11
* an extra range of instruction patterns is considered
to be inside the coprocessor space
We previously marked these up with TODO comments; implement the
correct behaviour.
Unfortunately there is no ID register field which indicates this
behaviour. We could in theory test an unrelated ID register which
indicates guaranteed-to-be-in-v8.1M behaviour like ID_ISAR0.CmpBranch
>= 3 (low-overhead-loops), but it seems better to simply define a new
ARM_FEATURE_V8_1M feature flag and use it for this and other
new-in-v8.1M behaviour that isn't identifiable from the ID registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-3-peter.maydell@linaro.org
Unlike many other bits in HCR_EL2, the description for this
bit does not contain the phrase "if ... this field behaves
as 0 for all purposes other than", so do not squash the bit
in arm_hcr_el2_eff.
Instead, replicate the E2H+TGE test in the two places that
require it.
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-id: 20201008162155.161886-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The reporting in AArch64.TagCheckFail only depends on PSTATE.EL,
and not the AccType of the operation. There are two guest
visible problems that affect LDTR and STTR because of this:
(1) Selecting TCF0 vs TCF1 to decide on reporting,
(2) Report "data abort same el" not "data abort lower el".
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-id: 20201008162155.161886-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We already have the full ARMMMUIdx as computed from the
function parameter.
For the purpose of regime_has_2_ranges, we can ignore any
difference between AccType_Normal and AccType_Unpriv, which
would be the only difference between the passed mmu_idx
and arm_mmu_idx_el.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-id: 20201008162155.161886-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When TBI is enabled in a given regime, 56 bits of the address
are significant and we need to clear out any other matching
virtual addresses with differing tags.
The other uses of tlb_flush_page (without mmuidx) in this file
are only used by aarch32 mode.
Fixes: 38d931687f
Reported-by: Jordan Frank <jordanfrank@fb.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201016210754.818257-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For AArch32, unlike the VCVT of integer to float, which honours the
rounding mode specified by the FPSCR, VCVT of fixed-point to float is
always round-to-nearest. (AArch64 fixed-point-to-float conversions
always honour the FPCR rounding mode.)
Implement this by providing _round_to_nearest versions of the
relevant helpers which set the rounding mode temporarily when making
the call to the underlying softfloat function.
We only need to change the VFP VCVT instructions, because the
standard- FPSCR value used by the Neon VCVT is always set to
round-to-nearest, so we don't need to do the extra work of saving
and restoring the rounding mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201013103532.13391-1-peter.maydell@linaro.org
The SMLAD instruction is supposed to:
* signed multiply Rn[15:0] * Rm[15:0]
* signed multiply Rn[31:16] * Rm[31:16]
* perform a signed addition of the products and Ra
* set Rd to the low 32 bits of the theoretical
infinite-precision result
* set the Q flag if the sign-extension of Rd
would differ from the infinite-precision result
(ie on overflow)
Our current implementation doesn't quite do this, though: it performs
an addition of the products setting Q on overflow, and then it adds
Ra, again possibly setting Q. This sometimes incorrectly sets Q when
the architecturally mandated only-check-for-overflow-once algorithm
does not. For instance:
r1 = 0x80008000; r2 = 0x80008000; r3 = 0xffffffff
smlad r0, r1, r2, r3
This is (-32768 * -32768) + (-32768 * -32768) - 1
The products are both 0x4000_0000, so when added together as 32-bit
signed numbers they overflow (and QEMU sets Q), but because the
addition of Ra == -1 brings the total back down to 0x7fff_ffff
there is no overflow for the complete operation and setting Q is
incorrect.
Fix this edge case by resorting to 64-bit arithmetic for the
case where we need to add three values together.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201009144712.11187-1-peter.maydell@linaro.org
QEMU supports a 48-bit physical address range, but we don't currently
expose it in the '-cpu max' ID registers (you get the same range as
Cortex-A57, which is 44 bits).
Set the ID_AA64MMFR0.PARange field to indicate 48 bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201001160116.18095-1-peter.maydell@linaro.org
We add the kvm-steal-time CPU property and implement it for machvirt.
A tiny bit of refactoring was also done to allow pmu and pvtime to
use the same vcpu device helper functions.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20201001061718.101915-7-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we compile without KVM support !defined(CONFIG_KVM) we generate
stubs for functions that the linker will still encounter. Sometimes
these stubs can be executed safely and are placed in paths where they
get executed with or without KVM. Other functions should never be
called without KVM. Those functions should be guarded by kvm_enabled(),
but should also be robust to refactoring mistakes. Putting a
g_assert_not_reached() in the function should help. Additionally,
the g_assert_not_reached() calls may actually help the linker remove
some code.
We remove the stubs for kvm_arm_get/put_virtual_time(), as they aren't
necessary at all - the only caller is in kvm.c
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20201001061718.101915-3-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
refactoring of cpus.c continues with cpu timer state extraction.
cpu-timers: responsible for the softmmu cpu timers state,
including cpu clocks and ticks.
icount: counts the TCG instructions executed. As such it is specific to
the TCG accelerator. Therefore, it is built only under CONFIG_TCG.
One complication is due to qtest, which uses an icount field to warp time
as part of qtest (qtest_clock_warp).
In order to solve this problem, provide a separate counter for qtest.
This requires fixing assumptions scattered in the code that
qtest_enabled() implies icount_enabled(), checking each specific case.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[remove redundant initialization with qemu_spice_init]
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[fix lingering calls to icount_get]
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While converting to gen_gvec_ool_zzzp, we lost passing
a->esz as the data argument to the function.
Fixes: 36cbb7a8e7
Cc: qemu-stable@nongnu.org
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200918000500.2690937-1-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The mte update missed a bit when producing clean addresses.
Fixes: b2aa8879b8
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200916014102.2446323-1-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The M-profile definition of the MVFR1 ID register differs slightly
from the A-profile one, and in particular the check for "does the CPU
support fp16 arithmetic" is not the same.
We don't currently implement any M-profile CPUs with fp16 arithmetic,
so this is not yet a visible bug, but correcting the logic now
disarms this beartrap for when we eventually do.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200910173855.4068-6-peter.maydell@linaro.org
Give the Cortex-M0 ID register values corresponding to its
implemented behaviour. These will not be guest-visible but will be
used to govern the behaviour of QEMU's emulation. We use the same
values that the Cortex-M3 does.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200910173855.4068-5-peter.maydell@linaro.org
Move the id_pfr0 and id_pfr1 fields into the ARMISARegisters
sub-struct. We're going to want id_pfr1 for an isar_features
check, and moving both at the same time avoids an odd
inconsistency.
Changes other than the ones to cpu.h and kvm64.c made
automatically with:
perl -p -i -e 's/cpu->id_pfr/cpu->isar.id_pfr/' target/arm/*.c hw/intc/armv7m_nvic.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200910173855.4068-3-peter.maydell@linaro.org
The ARM_FEATURE_PXN bit indicates whether the CPU supports the PXN
bit in short-descriptor translation table format descriptors. This
is indicated by ID_MMFR0.VMSA being at least 0b0100. Replace the
feature bit with an ID register check, in line with our preference
for ID register checks over feature bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200910173855.4068-2-peter.maydell@linaro.org
clang's C11 atomic_fetch_*() functions only take a C11 atomic type
pointer argument. QEMU uses direct types (int, etc) and this causes a
compiler error when a QEMU code calls these functions in a source file
that also included <stdatomic.h> via a system header file:
$ CC=clang CXX=clang++ ./configure ... && make
../util/async.c:79:17: error: address argument to atomic operation must be a pointer to _Atomic type ('unsigned int *' invalid)
Avoid using atomic_*() names in QEMU's atomic.h since that namespace is
used by <stdatomic.h>. Prefix QEMU's APIs with 'q' so that atomic.h
and <stdatomic.h> can co-exist. I checked /usr/include on my machine and
searched GitHub for existing "qatomic_" users but there seem to be none.
This patch was generated using:
$ git grep -h -o '\<atomic\(64\)\?_[a-z0-9_]\+' include/qemu/atomic.h | \
sort -u >/tmp/changed_identifiers
$ for identifier in $(</tmp/changed_identifiers); do
sed -i "s%\<$identifier\>%q$identifier%g" \
$(git grep -I -l "\<$identifier\>")
done
I manually fixed line-wrap issues and misaligned rST tables.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200923105646.47864-1-stefanha@redhat.com>
When debugging QEMU it is often useful to put a breakpoint on the
error_setg_internal method impl.
Unfortunately the object_property_add / object_class_property_add
methods call object_property_find / object_class_property_find methods
to check if a property exists already before adding the new property.
As a result there are a huge number of calls to error_setg_internal
on startup of most QEMU commands, making it very painful to set a
breakpoint on this method.
Most callers of object_find_property and object_class_find_property,
however, pass in a NULL for the Error parameter. This simplifies the
methods to remove the Error parameter entirely, and then adds some
new wrapper methods that are able to raise an Error when needed.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200914135617.1493072-1-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
One of the goals of having less boilerplate on QOM declarations
is to avoid human error. Requiring an extra argument that is
never used is an opportunity for mistakes.
Remove the unused argument from OBJECT_DECLARE_TYPE and
OBJECT_DECLARE_SIMPLE_TYPE.
Coccinelle patch used to convert all users of the macros:
@@
declarer name OBJECT_DECLARE_TYPE;
identifier InstanceType, ClassType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_TYPE(InstanceType, ClassType,
- lowercase,
UPPERCASE);
@@
declarer name OBJECT_DECLARE_SIMPLE_TYPE;
identifier InstanceType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_SIMPLE_TYPE(InstanceType,
- lowercase,
UPPERCASE);
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200916182519.415636-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We want to introduce a new version of qemu_open() that uses an Error
object for reporting problems and make this it the preferred interface.
Rename the existing method to release the namespace for the new impl.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
This check was backwards when introduced in commit
033614c47d:
target/arm: Filter cycle counter based on PMCCFILTR_EL0
Cc: qemu-stable@nongnu.org
Signed-off-by: Aaron Lindsay <aaron@os.amperecomputing.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
