Even though the BLAST command isn't fully implemented in QEMU, the DMA_STAT_BCMBLT
bit should be set after the command has been issued to indicate that the command
has completed.
This fixes an issue with the DC390 DOS driver which issues the BLAST command as
part of its normal error recovery routine at startup, and otherwise sits in a
tight loop waiting for DMA_STAT_BCMBLT to be set before continuing.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The setting of DMA_STAT_DONE at the end of a DMA transfer can be configured to
generate an interrupt, however the Linux driver manually checks for DMA_STAT_DONE
being set and if it is, considers that a DMA transfer has completed.
If DMA_STAT_DONE is set but the ESP device isn't indicating an interrupt then
the Linux driver considers this to be a spurious interrupt. However this can
occur in QEMU as there is a delay between the end of DMA transfer where
DMA_STAT_DONE is set, and the ESP device raising its completion interrupt.
This appears to be an incorrect assumption in the Linux driver as the ESP and
PCI DMA interrupt sources are separate (and may not be raised exactly
together), however we can work around this by synchronising the setting of
DMA_STAT_DONE at the end of a DMA transfer with the ESP completion interrupt.
In conjunction with the previous commit Linux is now able to correctly boot
from an am53c974 PCI SCSI device on the hppa C3700 machine without emitting
"iget: checksum invalid" and "Spurious irq, sreg=10" errors.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The am53c974/dc390 PCI interrupt has two separate sources: the first is from the
internal ESP device, and the second is from the PCI DMA transfer logic.
Update the ESP interrupt handler so that it sets DMA_STAT_SCSIINT rather than
driving the PCI IRQ directly, and introduce a new esp_pci_update_irq() function
to generate the correct PCI IRQ level. In particular this fixes spurious interrupts
being generated by setting DMA_STAT_DONE at the end of a transfer if DMA_CMD_INTE_D
isn't set in the DMA_CMD register.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The current code in esp_pci_dma_memory_rw() sets the DMA address to the value
of the DMA_SPA (Starting Physical Address) register which is incorrect: this
means that for each callback from the SCSI layer the DMA address is set back
to the starting address.
In the case where only a single SCSI callback occurs (currently for transfer
lengths < 128kB) this works fine, however for larger transfers the DMA address
wraps back to the initial starting address, corrupting the buffer holding the
data transferred to the guest.
Fix esp_pci_dma_memory_rw() to use the DMA_WAC (Working Address Counter) for
the DMA address which is correctly incremented across multiple SCSI layer
transfers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Mechanical change running Coccinelle spatch with content
generated from the qom-cast-macro-clean-cocci-gen.py added
in the previous commit.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230601093452.38972-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
PCIDeviceClass and PCIDevice are defined in pci.h. Many users of the
header don't actually need them. Similar structs live in their own
headers: PCIBusClass and PCIBus in pci_bus.h, PCIBridge in
pci_bridge.h, PCIHostBridgeClass and PCIHostState in pci_host.h,
PCIExpressHost in pcie_host.h, and PCIERootPortClass, PCIEPort, and
PCIESlot in pcie_port.h.
Move PCIDeviceClass and PCIDeviceClass to new pci_device.h, along with
the code that needs them. Adjust include directives.
This also enables the next commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-6-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let devices specify transaction attributes when calling pci_dma_rw().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-10-philmd@redhat.com>
The function scsi_bus_new() creates a new SCSI bus; callers can
either pass in a name argument to specify the name of the new bus, or
they can pass in NULL to allow the bus to be given an automatically
generated unique name. Almost all callers want to use the
autogenerated name; the only exception is the virtio-scsi device.
Taking a name argument that should almost always be NULL is an
easy-to-misuse API design -- it encourages callers to think perhaps
they should pass in some standard name like "scsi" or "scsi-bus". We
don't do this anywhere for SCSI, but we do (incorrectly) do it for
other bus types such as i2c.
The function name also implies that it will return a newly allocated
object, when it in fact does in-place allocation. We more commonly
name such functions foo_init(), with foo_new() being the
allocate-and-return variant.
Replace all the scsi_bus_new() callsites with either:
* scsi_bus_init() for the usual case where the caller wants
an autogenerated bus name
* scsi_bus_init_named() for the rare case where the caller
needs to specify the bus name
and document that for the _named() version it's then the caller's
responsibility to think about uniqueness of bus names.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20210923121153.23754-2-peter.maydell@linaro.org
If QEMU is launched with the -S option then the ESPState mig_version_id property
is left unset due to the ordering of the VMState fields in the VMStateDescription
for sysbusespscsi and pciespscsi. If the VM is migrated and restored in this
stopped state, the version tests in the vmstate_esp VMStateDescription and
esp_post_load() become confused causing the migration to fail.
Fix the ordering problem by moving the setting of mig_version_id to a common
esp_pre_save() function which is invoked first by both sysbusespscsi and
pciespscsi rather than at the point where ESPState is itself serialised into the
migration stream.
Buglink: https://bugs.launchpad.net/qemu/+bug/1922611
Fixes: 0bd005be78 ("esp: add vmstate_esp version to embedded ESPState")
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210407124842.32695-1-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Make this new QOM device state a child device of both the sysbus-esp and esp-pci
implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-4-mark.cave-ayland@ilande.co.uk>
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per AM53C974 datasheet, definition of "SCSI Bus and Control (SBAC)"
register:
Bit 24 'STATUS' Write Erase Control
This bit controls the Write Erase feature on bits 3:1 and bit 6 of the DMA
Status Register ((B)+54h). When this bit is programmed to '1', the state
of bits 3:1 are preserved when read. Bits 3:1 are only cleared when a '1'
is written to the corresponding bit location. For example, to clear bit 1,
the value of '0000_0010b' should be written to the register. When the DMA
Status Preserve bit is '0', bits 3:1 are cleared when read.
The status register is currently defined to bit 12, not bit 24.
Also, its implementation is reversed: The status is auto-cleared if
the bit is set to 1, and must be cleared explicitly when the bit is
set to 0. This results in spurious interrupts reported by the Linux
kernel, and in some cases even results in stalled SCSI operations.
Set SBAC_STATUS to bit 24 and reverse the logic to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <1543442171-24863-1-git-send-email-linux@roeck-us.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The logic to create frontends for -drive if=scsi is in SCSI HBAs. For
all other interface types, it's in machine initialization code.
A few machine types create the SCSI HBAs necessary for that. That's
also not done for other interface types.
I'm going to deprecate these SCSI eccentricities. In preparation for
that, create the frontends in main() instead of the SCSI HBAs, by
calling new function scsi_legacy_handle_cmdline() there.
Note that not all SCSI HBAs create frontends. Take care not to change
that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-2-git-send-email-armbru@redhat.com>
Acked-By: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-24-git-send-email-peter.maydell@linaro.org
These are "am53c974", "dc390", "lsi53c895a", "lsi53c810", "megasas",
"megasas-gen2".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-Id: <1425925048-15482-5-git-send-email-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit a818a4b changed scsi_bus_legacy_handle_cmdline() to report
errors from scsi_bus_legacy_add_drive() with error_report() in
addition to returning them. That's inappropriate.
Two kinds of callers:
1. realize methods (devices "esp", "virtio-scsi-device" and
"spapr-vscsi")
The error object gets passed up the call chain until it gets
reported again and freed.
Example:
$ qemu-system-arm -M virt -S -display none \
> -drive if=scsi,id=foo,bus=1,file=tmp.qcow2 \
> -device nec-usb-xhci -device usb-storage,drive=foo \
> -device virtio-scsi-pci
qemu-system-arm: -drive if=scsi,id=foo,bus=1,file=tmp.qcow2: Property 'scsi-disk.drive' can't take value 'foo', it's in use
qemu-system-arm: -drive if=scsi,id=foo,bus=1,file=tmp.qcow2: Setting drive property failed
qemu-system-arm: -device virtio-scsi-pci: Setting drive property failed
qemu-system-arm: -device virtio-scsi-pci: Device initialization failed
qemu-system-arm: -device virtio-scsi-pci: Device 'virtio-scsi-pci' could not be initialized
The second message in this error cascade comes from
scsi_bus_legacy_handle_cmdline(). The error object then gets
passed up to the qdev_init() called from
virtio_scsi_pci_init_pci(), which reports it again.
2. init methods (devices "am53c974", "dc390", "lsi53c895a",
"lsi53c810", "megasas", "megasas-gen2")
init methods need to report their errors with qerror_report().
These don't. The inappropriate error_report() papers over the bug.
error_report() isn't the same as qerror_report() in QMP context,
but this can't actually happen: QMP can still only hot-plug, and
callers call scsi_bus_legacy_handle_cmdline() only on cold-plug.
Except for sysbus_esp_realize(), but that can't be hot-plugged at
all, as far as I can tell.
Fix the init methods and drop the inappropriate error_report() in
scsi_bus_legacy_handle_cmdline().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-Id: <1425925048-15482-2-git-send-email-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A linux guest will be issuing messages:
[ 32.124042] DC390: Deadlock in DataIn_0: DMA aborted unfinished: 000000 bytes remain!!
[ 32.126348] DC390: DataIn_0: DMA State: 0
and the HBA will fail to work properly.
Reason is the emulation is not setting the 'DMA transfer done'
status correctly.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function is empty after the previous patch, so remove it.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
pci_set_irq and the other pci irq wrappers use
PCI_INTERRUPT_PIN config register to compute device
INTx pin to assert/deassert.
An irq is allocated using pci_allocate_irq wrapper
only if is needed by non pci devices.
Removed irq related fields from state if not used anymore.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To be passed to qbus_create_inplace().
Use DEVICE() casts instead of direct parent field access.
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Let scsi_bus_legacy_add_drive() and scsi_bus_legacy_handle_cmdline()
return an Error**. Prepare qdev initfns for QOM realize error model.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace direct uses of PCIESPState::dev with QOM casts and rename it to
parent_obj.
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Define and use standard QOM cast macro. Remove usages of DO_UPCAST()
and direct -> style upcasting.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This adds the possibility to create a scsi-bus with a specified name.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1367330931-12994-4-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
