They're used in quite a few places of pci.[ch] and also in the rest of the code
base. Define them so that it doesn't need to be defined all over the places.
The pci_bus_fn is similar to pci_bus_dev_fn that only takes a PCIBus* and an
opaque. The pci_bus_ret_fn is similar to pci_bus_fn but it allows to return a
void* pointer.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20211028043129.38871-2-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow instantiating a virtio-iommu device by adding an ACPI Virtual I/O
Translation table (VIOT), which describes the relation between the
virtio-iommu and the endpoints it manages.
Add a hotplug handler for virtio-iommu on x86 and set the necessary
reserved region property. On x86, the [0xfee00000, 0xfeefffff] DMA
region is reserved for MSIs. DMA transactions to this range either
trigger IRQ remapping in the IOMMU or bypasses IOMMU translation.
Although virtio-iommu does not support IRQ remapping it must be informed
of the reserved region so that it can forward DMA transactions targeting
this region.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20211026182024.2642038-5-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We're about to support a third vIOMMU for x86, virtio-iommu which
doesn't inherit X86IOMMUState. Move the IOMMU singleton into
PCMachineState, so it can be shared between all three vIOMMUs.
The x86_iommu_get_default() helper is still needed by KVM and IOAPIC to
fetch the default IRQ-remapping IOMMU. Since virtio-iommu doesn't
support IRQ remapping, this interface doesn't need to change for the
moment. We could later replace X86IOMMUState with an "IRQ remapping
IOMMU" interface if necessary.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20211026182024.2642038-4-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To generate the IOMMU ACPI table, acpi-build.c can use base QEMU types
instead of a special IommuType value.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20211026182024.2642038-3-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a function that generates a Virtual I/O Translation table (VIOT),
describing the topology of paravirtual IOMMUs. The table is created if a
virtio-iommu device is present. It contains a virtio-iommu node and PCI
Range nodes for endpoints managed by the IOMMU. By default, a single
node describes all PCI devices. When passing the
"default_bus_bypass_iommu" machine option and "bypass_iommu" PXB option,
only buses that do not bypass the IOMMU are described by PCI Range
nodes.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20211026182024.2642038-2-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Similar to VFIO, vDPA will go ahead an map+pin all guest memory. Memory
that used to be discarded will get re-populated and if we
discard+re-access memory after mapping+pinning, the pages mapped into the
vDPA IOMMU will go out of sync with the actual pages mapped into the user
space page tables.
Set discarding of RAM broken such that:
- virtio-mem and vhost-vdpa run mutually exclusive
- virtio-balloon is inhibited and no memory discards will get issued
In the future, we might be able to support coordinated discarding of RAM
as used by virtio-mem and already supported by vfio via the
RamDiscardManager.
Acked-by: Jason Wang <jasowang@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Cindy Lu <lulu@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20211027130324.59791-1-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
The hw_error function calls abort and is not meant to be used by
devices. Use qemu_log_mask instead to log and ignore invalid accesses.
Also fix format strings to allow dropping type casts of hwaddr and use
__func__ instead of hard coding function name in the message which
were wrong in two cases.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <f818dc3dd2ac8c3b3d53067f316a716d7f9683d8.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The timer unit only has registers that fit in a region 0x30 bytes
long. No need to have the timer region larger than that.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <b1cd196cf1395a602c7a08a4f858e69e50c446a1.1635550060.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
It's more readable to keep things on one line if it fits the length limit.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <97bc2a38991f33fd0c8cc2e4d0a3a29b20c47d1f.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
According to coding style types should be camel case, also remove
unneded casts from void *.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <d9a9d160c1153a583397e366ab06477f5a31c507.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The sh_intc_locate function will either init these or not return so no
need to initialise them.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <15e04aa665c68ab5df47bbf505346d413be2fc1c.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use g_new0 instead of g_malloc0 and avoid some unneeded temporary
variable assignments.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <72efc4f2c4ff8b96848d03dca08e4541ee4076f6.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instead of if !expr continue else do something it is more straight
forward to say if expr then do something, especially if the action is
just a few lines. Remove such uses of continue to make the code easier
to follow.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <0efaa5e7a1a3ee11f82b3bb1942c287576c67f8b.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
All the places that call abort should not happen which is better
marked by g_assert_not_reached.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <039e6a784532f2af27f8adeafdb8e0391722f567.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This function is very simple and provides no advantage. Call sites
become simpler without it so just write it in line and drop the
separate function.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <a98d1f7f94e91a42796b7d91e9153a7eaa3d1c44.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Address of element i is one word thus clearer than array + i.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <f49c9b1dee1fcaf374b092d862a6821907d5fcdc.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Drop unneded parenthesis and split up one complex expression to write
it with less brackets so it's easier to follow.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <a48e849e5b803a952ed15a2502cfece2bde68934.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The sh_intc_register() function is only used at one place. Move them
together so it's easier to see what's going on.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <49f2742bc67cba7164385fafad204ab1e1bd3a0b.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The INT_REG_PARAMS macro was only used a few times within one function
on adjacent lines and is actually more complex than writing out the
parameters so simplify it by expanding the macro at call sites and
dropping the #define.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <d3bdfdc5ab5ae1c51a6c6c38bde3829a99f85ce5.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Rename the iomem region to "intc" from "interrupt-controller" which
makes the info mtree output less wide as it is already too wide
because of all the aliases. Also drop the format macro which was only
used twice in close proximity so we can just use the literal string
instead without a macro definition.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cb6402dab6b44c804142b5cf9af68e6398cb613f.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Turn the INTC_MODE defines into an enum and clean up the function
returning these to make it clearer by removing nested ifs and
superfluous parenthesis. The one remaining #define is a flag which is
moved further apart by changing its value from 8 to 0x80 to leave some
spare bits as this is or-ed with the enum value at some places.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <4adf4e1ac9d2e728e5a536c69e310d77f0c4455a.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The INTC_A7 local macro does the same as the A7ADDR from
include/sh/sh.h so use the latter and drop the local macro definition.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <53f033477c73b7c9b021d36033c590416d6199c7.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Normally there are at least two sh_serial instances. Add device id to
trace messages to make it clear which instance they belong to
otherwise its not possible to tell which serial device is accessed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <cc1f9ff9f4259ae799750e452f8871849c7a104c.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <92902ba34fdf2c8c62232365fbb6531b1036d557.1635541329.git.balaton@eik.bme.hu>
[PMD: Use g_strdup() to initialize DeviceState::id]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instead of allocating timer with timer_new store it directly in the
state struct. This makes it simpler to free it together with the device.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <fd01eb3720ec32dab06e03019f72f3e177033679.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace fprintf with qemu_log_mask LOG_GUEST_ERROR as the intention is
to handle valid accesses in these functions so if we get to these
errors then it's an invalid access. Do not abort as that would allow
the guest to crash QEMU and the practice in other devices is to not do
that just log and ignore the invalid access. While at it also simplify
the complex bit ops to check if a return value was set which can be
done much simpler and clearer.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <6b46045141d6d9cc32e17c223896fa1116384796.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Fixup the PLIC context address to correctly support the threshold and
claim register.
Fixes: ef63100648 ("hw/riscv: opentitan: Update to the latest build")
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211025040657.262696-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-5-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-4-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-3-alistair.francis@opensource.wdc.com
Add a generic function that can create the PLIC strings.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-2-alistair.francis@opensource.wdc.com
Using a macro for the PLIC configuration doesn't make the code any
easier to read. Instead it makes it harder to figure out what is going
on, so let's remove it.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20211022060133.3045020-1-alistair.francis@opensource.wdc.com
Use QEMU_ALIGN_DOWN() macro to reduce code and to make it
more human readable.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <b84eb324d2ebdcc6f9c442c97b5b4d01eecb4f43.1632758315.git.qemu_oss@crudebyte.com>
When client sent a 9p Tgetattr request then the wrong I/O block
size value was returned by 9p server; instead of host file
system's I/O block size it should rather return an I/O block
size according to 9p session's 'msize' value, because the value
returned to client should be an "optimum" block size for I/O
(i.e. to maximize performance), it should not reflect the actual
physical block size of the underlying storage media.
The I/O block size of a host filesystem is typically 4k, so the
value returned was far too low for good 9p I/O performance.
This patch adds stat_to_iounit() with a similar approach as the
existing get_iounit() function.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <E1mT2Js-0000DW-OH@lizzy.crudebyte.com>
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211015203532.2463705-4-tong.ho@xilinx.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211015203532.2463705-3-tong.ho@xilinx.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
