Currently QEMU defaults to a resolution of 1024x768 when exposing EDID
info to the guest OS. The EDID default info is important as this will
influence what resolution many guest OS will configure the screen with
on boot. It can also potentially influence what resolution the firmware
will configure the screen with, though until very recently EDK2 would
not handle EDID info.
One important thing to bear in mind is that the default graphics card
driver provided by Windows will leave the display set to whatever
resolution was enabled by the firmware on boot. Even if sufficient
VRAM is available, the resolution can't be changed without installing
new drivers. IOW, the default resolution choice is quite important
for usability of Windows.
Modern real world monitor hardware for desktop/laptop has supported
resolutions higher than 1024x768 for a long time now, perhaps as long
as 15+ years. There are quite a wide variety of native resolutions in
use today, however, and in wide screen form factors the height may not
be all that tall.
None the less, it is considered that there is scope for making the
QEMU default resolution slightly larger.
In considering what possible new default could be suitable, choices
considered were 1280x720 (720p), 1280x800 (WXGA) and 1280x1024 (SXGA).
In many ways, vertical space is the most important, and so 720p was
discarded due to loosing vertical space, despite being 25% wider.
The SXGA resolution would be good, but when taking into account
window titlebars/toolbars and window manager desktop UI, this might
be a little too tall for some users to fit the guest on their physical
montior.
This patch thus suggests a modest change to 1280x800 (WXGA). This
only consumes 1 MB per colour channel, allowing double buffered
framebuffer in 8 MB of VRAM. Width wise this is 25% larger than
QEMU's current default, but height wise this only adds 5%, so the
difference isn't massive on the QEMU side.
Overall there doesn't appear to be a compelling reason to stick
with 1024x768 resolution.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211129140508.1745130-1-berrange@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Now that virtio-blk and virtio-scsi are ready, get rid of
the handle_aio_output() callback. It's no longer needed.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20211207132336.36627-7-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The return value of virtio_blk_handle_vq() is no longer used. Get rid of
it. This is a step towards unifying the dataplane and non-dataplane
virtqueue handler functions.
Prepare virtio_blk_handle_output() to be used by both dataplane and
non-dataplane by making the condition for starting ioeventfd more
specific. This way it won't trigger when dataplane has already been
started.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20211207132336.36627-4-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The virtqueue host notifier API
virtio_queue_aio_set_host_notifier_handler() polls the virtqueue for new
buffers. AioContext previously required a bool progress return value
indicating whether an event was handled or not. This is no longer
necessary because the AioContext polling API has been split into a poll
check function and an event handler function. The event handler is only
run when we know there is work to do, so it doesn't return bool.
The VirtIOHandleAIOOutput function signature is now the same as
VirtIOHandleOutput. Get rid of the bool return value.
Further simplifications will be made for virtio-blk and virtio-scsi in
the next patch.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20211207132336.36627-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This reverts commit 8806237234.
Fixes: 8806237234 ("vhost: introduce new VhostOps vhost_set_config_call")
Cc: "Cindy Lu" <lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit 081f864f56.
Fixes: 081f864f56 ("virtio: add support for configure interrupt")
Cc: "Cindy Lu" <lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit f7220a7ce2.
Fixes: f7220a7ce2 ("vhost: add support for configure interrupt")
Cc: "Cindy Lu" <lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
With VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE, we signal the VM that reading
unplugged memory is not supported. We have to fail feature negotiation
in case the guest does not support VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE.
First, VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE is required to properly handle
memory backends (or architectures) without support for the shared zeropage
in the hypervisor cleanly. Without the shared zeropage, even reading an
unpopulated virtual memory location can populate real memory and
consequently consume memory in the hypervisor. We have a guaranteed shared
zeropage only on MAP_PRIVATE anonymous memory.
Second, we want VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE to be the default
long-term as even populating the shared zeropage can be problematic: for
example, without THP support (possible) or without support for the shared
huge zeropage with THP (unlikely), the PTE page tables to hold the shared
zeropage entries can consume quite some memory that cannot be reclaimed
easily.
Third, there are other optimizations+features (e.g., protection of
unplugged memory, reducing the total memory slot size and bitmap sizes)
that will require VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE.
We really only support x86 targets with virtio-mem for now (and
Linux similarly only support x86), but that might change soon, so prepare
for different targets already.
Add a new "unplugged-inaccessible" tristate property for x86 targets:
- "off" will keep VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE unset and legacy
guests working.
- "on" will set VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE and stop legacy guests
from using the device.
- "auto" selects the default based on support for the shared zeropage.
Warn in case the property is set to "off" and we don't have support for the
shared zeropage.
For existing compat machines, the property will default to "off", to
not change the behavior but eventually warn about a problematic setup.
Short-term, we'll set the property default to "auto" for new QEMU machines.
Mid-term, we'll set the property default to "on" for new QEMU machines.
Long-term, we'll deprecate the parameter and disallow legacy
guests completely.
The property has to match on the migration source and destination. "auto"
will result in the same VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE setting as long
as the qemu command line (esp. memdev) match -- so "auto" is good enough
for migration purposes and the parameter doesn't have to be migrated
explicitly.
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20211217134039.29670-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For scarce memory resources, such as hugetlb, we want to be able to
prealloc such memory resources in order to not crash later on access. On
simple user errors we could otherwise easily run out of memory resources
an crash the VM -- pretty much undesired.
For ordinary memory devices, such as DIMMs, we preallocate memory via the
memory backend for such use cases; however, with virtio-mem we're dealing
with sparse memory backends; preallocating the whole memory backend
destroys the whole purpose of virtio-mem.
Instead, we want to preallocate memory when actually exposing memory to the
VM dynamically, and fail plugging memory gracefully + warn the user in case
preallocation fails.
A common use case for hugetlb will be using "reserve=off,prealloc=off" for
the memory backend and "prealloc=on" for the virtio-mem device. This
way, no huge pages will be reserved for the process, but we can recover
if there are no actual huge pages when plugging memory. Libvirt is
already prepared for this.
Note that preallocation cannot protect from the OOM killer -- which
holds true for any kind of preallocation in QEMU. It's primarily useful
only for scarce memory resources such as hugetlb, or shared file-backed
memory. It's of little use for ordinary anonymous memory that can be
swapped, KSM merged, ... but we won't forbid it.
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20211217134611.31172-9-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add functions to support configure interrupt.
The configure interrupt process will start in vhost_dev_start
and stop in vhost_dev_stop.
Also add the functions to support vhost_config_pending and
vhost_config_mask, for masked_config_notifier, we only
use the notifier saved in vq 0.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-8-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add the functions to support the configure interrupt in virtio
The function virtio_config_guest_notifier_read will notify the
guest if there is an configure interrupt.
The function virtio_config_set_guest_notifier_fd_handler is
to set the fd hander for the notifier
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-7-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces new VhostOps vhost_set_config_call. This function allows the
vhost to set the event fd to kernel
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-5-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To support configure interrupt for vhost-vdpa
Introduce VIRTIO_CONFIG_IRQ_IDX -1 as configure interrupt's queue index,
Then we can reuse the functions guest_notifier_mask and guest_notifier_pending.
Add the check of queue index in these drivers, if the driver does not support
configure interrupt, the function will just return
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-2-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In Linux 5.16, the padding of struct virtio_gpu_ctrl_hdr has become a
single-byte field followed by a uint8_t[3] array of padding bytes,
and virtio_gpu_ctrl_hdr_bswap does not compile anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211111110604.207376-2-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The doc of this field pointed out that last_index is the last vq index.
This is misleading, since it's actually one past the end of the vqs.
Renaming and modifying comment.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211104085625.2054959-2-eperezma@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When guest is running Linux/X11 with extended multiple displays mode enabled,
the guest shares one scanout resource each time containing whole surface
rather than sharing individual display output separately. This extended frame
is properly splited and rendered on the corresponding scanout surfaces but
not in case of blob-resource (zero copy).
This code change lets the qemu split this one large surface data into multiple
in case of blob-resource as well so that each sub frame then can be blitted
properly to each scanout.
v2: resizing qemu console in virtio_gpu_update_dmabuf to scanout's width and
height
v3: updating stub function of virtio_gpu_update_dmabuf to match the type
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Message-Id: <20211104065153.28897-5-dongwon.kim@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Migration code now properly handles RAMBlocks which are indirectly managed
by a RamDiscardManager. No need for manual handling via the free page
optimization interface, let's get rid of it.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This patch implements the control virtqueue support for vhost. This
requires virtio-net to figure out the datapath queue pairs and control
virtqueue via is_datapath and pass the number of those two types
of virtqueues to vhost_net_start()/vhost_net_stop().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211020045600.16082-10-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces a new field in the vhost_dev structure to record
the last virtqueue index for the virtio device. This will be useful
for the vhost backends with 1:N model to start or stop the device
after all the vhost_dev structures were started or stopped.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211020045600.16082-9-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Most of the time, "queues" really means queue pairs. So this patch
switch to use "queue_pairs" to avoid confusion.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211020045600.16082-8-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Vhost-vdpa uses one device multiqueue queue (pairs) model. So we need
to classify the one time request (e.g SET_OWNER) and make sure those
request were only called once per device.
This is used for multiqueue support.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211020045600.16082-3-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a random number generator (RNG) backend that communicates
with a vhost-user server to retrieve entropy. That way other VMM
that comply with the vhost user protocl can use the same vhost-user
daemon without having to write yet another RNG driver.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Message-Id: <20211012205904.4106769-2-mathieu.poirier@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop base_name and turn generic_name into
"virtio-iommu-pci". This is more in line with
other modern-only devices.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20211013191755.767468-3-eric.auger@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Check vdpa device range before updating memory regions so we don't add
any outside of it, and report the invalid change if any.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20211014141236.923287-4-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
QDicts are both what QMP natively uses and what the keyval parser
produces. Going through QemuOpts isn't useful for either one, so switch
the main device creation function to QDicts. By sharing more code with
the -object/object-add code path, we can even reduce the code size a
bit.
This commit doesn't remove the detour through QemuOpts from any code
path yet, but it allows the following commits to do so.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20211008133442.141332-15-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of accessing the global QemuOptsList, which really belong to the
command line parser and shouldn't be accessed from devices, store a
pointer to the QemuOpts in a new VirtIONet field.
This is not the final state, but just an intermediate step to get rid of
QemuOpts in devices. It will later be replaced with an options QDict.
Before this patch, two "primary" devices could be hidden for the same
standby device, but only one of them would actually be enabled and the
other one would be kept hidden forever, so this doesn't make sense.
After this patch, configuring a second primary device is an error.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20211008133442.141332-13-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
virtio-vsock features, like VIRTIO_VSOCK_F_SEQPACKET, can be handled
by vhost-vsock-common parent class. In this way, we can reuse the
same code for all virtio-vsock backends (i.e. vhost-vsock,
vhost-user-vsock).
Let's move `seqpacket` property to vhost-vsock-common class, add
vhost_vsock_common_get_features() used by children, and disable
`seqpacket` for vhost-user-vsock device for machine types < 6.2.
The behavior of vhost-vsock device doesn't change; vhost-user-vsock
device now supports `seqpacket` property.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210921161642.206461-3-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 1e08fd0a46 ("vhost-vsock: SOCK_SEQPACKET feature bit support")
enabled the SEQPACKET feature bit.
This commit is released with QEMU 6.1, so if we try to migrate a VM where
the host kernel supports SEQPACKET but machine type version is less than
6.1, we get the following errors:
Features 0x130000002 unsupported. Allowed features: 0x179000000
Failed to load virtio-vhost_vsock:virtio
error while loading state for instance 0x0 of device '0000:00:05.0/virtio-vhost_vsock'
load of migration failed: Operation not permitted
Let's disable the feature bit for machine types < 6.1.
We add a new OnOffAuto property for this, called `seqpacket`.
When it is `auto` (default), QEMU behaves as before, trying to enable the
feature, when it is `on` QEMU will fail if the backend (vhost-vsock
kernel module) doesn't support it.
Fixes: 1e08fd0a46 ("vhost-vsock: SOCK_SEQPACKET feature bit support")
Cc: qemu-stable@nongnu.org
Reported-by: Jiang Wang <jiang.wang@bytedance.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210921161642.206461-2-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Switch to use unsigned int for nvqs since it's not expected to be
negative.
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210903091031.47303-5-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduce a new method for the virtio-bus for the transport
to report whether or not the IOMMU is enabled for the device.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210804034803.1644-2-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Just a small refactor patch.
vhost_set_backend_type() gets called only in vhost.c, so we can move the
function there and make it static. We can then extern the visibility of
kernel_ops, to match the other VhostOps in vhost-backend.h.
The VhostOps constants now make more sense in vhost.h
Suggested-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Tiberiu Georgescu <tiberiu.georgescu@nutanix.com>
Message-Id: <20210809134015.67941-1-tiberiu.georgescu@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
With the introduction of the batch hinting, meaningless batches can be
created with no IOTLB updates if the memory region was skipped by
vhost_vdpa_listener_skipped_section. This is the case of host notifiers
memory regions, device un/realize, and others. This causes the vdpa
device to receive dma mapping settings with no changes, a possibly
expensive operation for nothing.
To avoid that, VHOST_IOTLB_BATCH_BEGIN hint is delayed until we have a
meaningful (not skipped section) mapping or unmapping operation, and
VHOST_IOTLB_BATCH_END is not written unless at least one of _UPDATE /
_INVALIDATE has been issued.
v3:
* Use a bool instead of a counter avoiding potential number wrapping
* Fix bad check on _commit
* Move VHOST_BACKEND_F_IOTLB_BATCH check to
vhost_vdpa_iotlb_batch_begin_once
v2 (from RFC):
* Rename misleading name
* Abstract start batching function for listener_add/del
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20210812140933.226288-1-eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Before commit 49afbca3b0 ("virtio-gpu: drop
use_virgl_renderer"), use_virgl_renderer was preventing calling GL
functions from non-GL context threads. The innocuously looking
g->parent_obj.use_virgl_renderer = false;
was set the first time virtio_gpu_gl_reset() was called, during
pc_machine_reset() in the main thread. Further virtio_gpu_gl_reset()
calls in IO threads, without associated GL context, were thus skipping
GL calls and avoided warnings or crashes (see also
https://gitlab.freedesktop.org/virgl/virglrenderer/-/issues/226).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210702123221.942432-1-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This creates the QEMU side of the vhost-user-i2c device which connects
to the remote daemon. It is based of vhost-user-fs code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Message-Id: <e80591b52fea4b51631818bb92a798a3daf90399.1625806763.git.viresh.kumar@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's properly notify when (un)plugging blocks, after discarding memory
and before allowing the guest to consume memory. Handle errors from
notifiers gracefully (e.g., no remaining VFIO mappings) when plugging,
rolling back the change and telling the guest that the VM is busy.
One special case to take care of is replaying all notifications after
restoring the vmstate. The device starts out with all memory discarded,
so after loading the vmstate, we have to notify about all plugged
blocks.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-6-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of just returning 0/-1 and letting the caller make up a
meaningless error message, add an Error parameter to allow reporting the
real error and switch to 0/-errno so that different kind of errors can
be distinguished in the caller.
config_len in vhost_user_get_config() is defined by the device, so if
it's larger than VHOST_USER_MAX_CONFIG_SIZE, this is a programming
error. Turn the corresponding check into an assertion.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-6-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of just returning 0/-1 and letting the caller make up a
meaningless error message, add an Error parameter to allow reporting the
real error and switch to 0/-errno so that different kind of errors can
be distinguished in the caller.
Specifically, in vhost-user, EPROTO is used for all errors that relate
to the connection itself, whereas other error codes are used for errors
relating to the content of the connection. This will allow us later to
automatically reconnect when the connection goes away, without ending up
in an endless loop if it's a permanent error in the configuration.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-3-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This allows callers to return better error messages instead of making
one up while the real error ends up on stderr. Most callers can
immediately make use of this because they already have an Error
parameter themselves. The others just keep printing the error with
error_report_err().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-2-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch implements the vq notification mapping support for
vhost-vDPA. This is simply done by using mmap()/munmap() for the
vhost-vDPA fd during device start/stop. For the device without
notification mapping support, we fall back to eventfd based
notification gracefully.
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The symbol address_space_memory are already declared in
include/exec/address-spaces.h. So let's add this header file
and remove the redundant declaration in include/hw/virtio/vhost-vdpa.h.
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210517123246.999-1-xieyongji@bytedance.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When RSS is enabled the device tries to load the eBPF program
to select RX virtqueue in the TUN. If eBPF can be loaded
the RSS will function also with vhost (works with kernel 5.8 and later).
Software RSS is used as a fallback with vhost=off when eBPF can't be loaded
or when hash population requested by the guest.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This API allows Qemu to set the blob allocated by the Guest as
the scanout buffer. If Opengl support is available, then the
scanout buffer would be submitted as a dmabuf to the UI; if not,
a pixman image is created from the scanout buffer and is
submitted to the UI via the display surface.
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-14-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
These helpers can be useful for creating dmabuf objects from blobs
and submitting them to the UI.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-12-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This API allows Qemu to register the blob allocated by the Guest
as a new resource and map its backing storage.
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-10-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add the property bit, configuration flag and other relevant
macros and definitions associated with this feature.
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-9-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Instead of passing the attach_backing object to extract nr_entries
and offset, explicitly pass these as arguments to this function.
This will be helpful when adding create_blob API.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-8-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Store the meta-data associated with a FB in a new object
(struct virtio_gpu_framebuffer) and pass the object to set_scanout.
Also move code in set_scanout into a do_set_scanout function.
This will be helpful when adding set_scanout_blob API.
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-7-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add helper functions to create a dmabuf for a resource and mmap it.
Also, introduce the fields blob and blob_size so that these helpers
can start to use them but the full picture will emerge only after
adding create_blob API in patch 8 of this series.
To be able to create a dmabuf using the udmabuf driver, Qemu needs
to be lauched with the memfd memory backend like this:
qemu-system-x86_64 -m 8192m -object memory-backend-memfd,id=mem1,size=8192M
-machine memory-backend=mem1
Based-on-patch-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210526231429.1045476-4-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Creating a device with a number of queues that isn't supported by the
backend is pointless, the device won't work properly and the error
messages are rather confusing.
Just fail to create the device if num-queues is higher than what the
backend supports.
Since the relationship between num-queues and the number of virtqueues
depends on the specific device, this is an additional value that needs
to be initialised by the device. For convenience, allow leaving it 0 if
the check should be skipped. This makes sense for vhost-user-net where
separate vhost devices are used for the queues and custom initialisation
code is needed to perform the check.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1935031
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20210429171316.162022-7-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmCeiMEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpqsIH/A49Av5Bv8huL75lf9GzCx3E1a/z2W9Fphik
OcQ1ahR+7CRDARub+vTG40MBmZBVefIWjLAj3BwBWzFGPX0DZq0zeI102VzlEVKY
OeUx8ixuiKOSLcS+QxE7ZXIBL2Pn7l+MFUi4nLMYKti7c/kola7zlB57qsmXh+VD
AOQ7Utj6NWoi6QocWJsMSCyHCh3Fk9QzcStLlr6/MkSJa1zqv8l22+8oWH07Fk2M
wZfhrm9k094on28iSejsFYL5e4ROeXUajbOdfyMIxWvAB7boC9Jxk/e0oAbuSB4y
2f71Gfk3mU6irS7PvrxcKbk6BVD2zxM2WumOchZJgxFAujDO6yg=
=fvkT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,virtio: bugfixes, improvements
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 14 May 2021 15:27:13 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
Fix build with 64 bits time_t
vhost-vdpa: Make vhost_vdpa_get_device_id() static
hw/virtio: enable ioeventfd configuring for mmio
hw/smbios: support for type 41 (onboard devices extended information)
checkpatch: Fix use of uninitialized value
virtio-scsi: Configure all host notifiers in a single MR transaction
virtio-scsi: Set host notifiers and callbacks separately
virtio-blk: Configure all host notifiers in a single MR transaction
virtio-blk: Fix rollback path in virtio_blk_data_plane_start()
pc-dimm: remove unnecessary get_vmstate_memory_region() method
amd_iommu: fix wrong MMIO operations
virtio-net: Constify VirtIOFeature feature_sizes[]
virtio-blk: Constify VirtIOFeature feature_sizes[]
hw/virtio: Pass virtio_feature_get_config_size() a const argument
x86: acpi: use offset instead of pointer when using build_header()
amd_iommu: Fix pte_override_page_mask()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/arm/virt.c
As it's only used inside hw/virtio/vhost-vdpa.c.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-Id: <20210413133737.1574-1-yuzenghui@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds ioeventfd flag for virtio-mmio configuration.
It allows switching ioeventfd on and off.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Message-Id: <161700379211.1135943.8859209566937991305.stgit@pasha-ThinkPad-X280>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The VirtIOFeature structure isn't modified, mark it const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210511104157.2880306-2-philmd@redhat.com>
Now that we have separated the gl and non-gl code flows to two different
devices there is little reason turn on and off virglrenderer usage at
runtime. The gl code can simply use virglrenderer unconditionally.
So drop use_virgl_renderer field and just do that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-13-kraxel@redhat.com>
Move device init (realize) and properties.
Drop the virgl property, the virtio-gpu-gl-device has virgl enabled no
matter what. Just use virtio-gpu-device instead if you don't want
enable virgl and opengl. This simplifies the logic and reduces the test
matrix.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-4-kraxel@redhat.com>
Just a skeleton for starters, following patches will add more code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-3-kraxel@redhat.com>
dma_memory_map() may map only a part of the request. Happens if the
request can't be mapped in one go, for example due to a iommu creating
a linear dma mapping for scattered physical pages. Should that be the
case virtio-gpu must call dma_memory_map() again with the remaining
range instead of simply throwing an error.
Note that this change implies the number of iov entries may differ from
the number of mapping entries sent by the guest. Therefore the iov_len
bookkeeping needs some updates too, we have to explicitly pass around
the iov length now.
Reported-by: Auger Eric <eric.auger@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210506091001.1301250-1-kraxel@redhat.com
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210506091001.1301250-1-kraxel@redhat.com>
Report the configured granularity for discard operation to the
guest. If this is not set use the block size.
Since until now we have ignored the configured discard granularity
and always reported the block size, let's add
'report-discard-granularity' property and disable it for older
machine types to avoid migration issues.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20210225001239.47046-1-akihiko.odaki@gmail.com>
Displaying rendered resources requires blocking qemu GPU to avoid extra
framebuffer copies. For an external display, via Spice currently, there
is a callback to block/unblock the rendering in the same thread.
But with the vhost-user-gpu backend, the qemu process doesn't handle
the rendering itself, and the blocking callback isn't effective.
Instead, the backend must be notified when the display code is done.
Fix this by adding a new GraphicHwOps callback to indicate the GL state
is flushed, and we are done manipulating the shared GL resources. Call
it from gtk and spice display.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-19-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The next patch will notify the GL context got flush, which will resume
the queue processing. However, if this happens within the caller
context, it will end up with a stack overflow flush/update loop.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-18-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
virtio-fs qualifies as a bootable device minimally under OVMF, but
currently the necessary "bootindex" property is missing. Add the property.
Expose the property only in the PCI device, for now. There is no boot
support for virtiofs on s390x (ccw) for the time being [1] [2], so leave
the CCW device unchanged. Add the property to the base device still,
because adding the alias to the CCW device later will be easier this way
[3].
[1] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg01745.html
[2] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg01870.html
[3] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg01751.html
Example OpenFirmware device path for the "vhost-user-fs-pci" device in the
"bootorder" fw_cfg file:
/pci@i0cf8/pci-bridge@1,6/pci1af4,105a@0/filesystem@0
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Ján Tomko <jtomko@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: virtio-fs@redhat.com
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210112131603.12686-1-lersek@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only three uses remained, and we can remove them on that case.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-28-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-25-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was only used once. And we have there opts->id, so no need for it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-13-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can calculate it, and we only use it once anyways.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-12-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was really only used once, in failover_add_primary(). Just search
for it on global opts when it is needed.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-11-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
You should not use passive naming variables.
And once there, be able to search for them.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-9-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Just remove the struct member.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-5-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Virtqueue has split and packed, so before setting inflight,
you need to inform the back-end virtqueue format.
Signed-off-by: Jin Yu <jin.yu@intel.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20201103123617.28256-1-jin.yu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit adb29c0273.
The commit broke -device vhost-user-blk-pci because the
vhost_dev_prepare_inflight() function it introduced segfaults in
vhost_dev_set_features() when attempting to access struct vhost_dev's
vdev pointer before it has been assigned.
To reproduce the segfault simply launch a vhost-user-blk device with the
contrib vhost-user-blk device backend:
$ build/contrib/vhost-user-blk/vhost-user-blk -s /tmp/vhost-user-blk.sock -r -b /var/tmp/foo.img
$ build/qemu-system-x86_64 \
-device vhost-user-blk-pci,id=drv0,chardev=char1,addr=4.0 \
-object memory-backend-memfd,id=mem,size=1G,share=on \
-M memory-backend=mem,accel=kvm \
-chardev socket,id=char1,path=/tmp/vhost-user-blk.sock
Segmentation fault (core dumped)
Cc: Jin Yu <jin.yu@intel.com>
Cc: Raphael Norwitz <raphael.norwitz@nutanix.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20201102165709.232180-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Virtqueue has split and packed, so before setting inflight,
you need to inform the back-end virtqueue format.
Signed-off-by: Jin Yu <jin.yu@intel.com>
Message-Id: <20200910134851.7817-1-jin.yu@intel.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Qemu will send GET_INFLIGHT_FD and SET_INFLIGH_FD to backend, and
the backend setup the inflight memory to track the io.
Change-Id: I805d6189996f7a1b44c65f0b12ef7473b1789510
Signed-off-by: Li Feng <fengli@smartx.com>
Message-Id: <20200909122021.1055174-1-fengli@smartx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only qemu-system-FOO and qemu-storage-daemon provide QMP
monitors, therefore such declarations and definitions are
irrelevant for user-mode emulation.
Restricting the memory commands to machine.json pulls less
QAPI-generated code into user-mode.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200913195348.1064154-7-philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Commit 9b3a35ec82 ("virtio: verify that legacy support is not accidentally
on") added a check that returns an error if legacy support is on, but the
device does not support legacy.
Unfortunately some devices were wrongly declared legacy capable even if
they were not (e.g vhost-vsock).
To avoid migration issues, we add a virtio-device property
(x-disable-legacy-check) to skip the legacy error, printing a warning
instead, for machine types < 5.1.
Cc: qemu-stable@nongnu.org
Fixes: 9b3a35ec82 ("virtio: verify that legacy support is not accidentally on")
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200921122506.82515-2-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost-user devices can get a disconnect in the middle of the VHOST-USER
handshake on the migration start. If disconnect event happened right
before sending next VHOST-USER command, then the vhost_dev_set_log()
call in the vhost_migration_log() function will return error. This error
will lead to the assert() and close the QEMU migration source process.
For the vhost-user devices the disconnect event should not break the
migration process, because:
- the device will be in the stopped state, so it will not be changed
during migration
- if reconnect will be made the migration log will be reinitialized as
part of reconnect/init process:
#0 vhost_log_global_start (listener=0x563989cf7be0)
at hw/virtio/vhost.c:920
#1 0x000056398603d8bc in listener_add_address_space (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2664
#2 0x000056398603dd30 in memory_listener_register (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2740
#3 0x0000563985fd6956 in vhost_dev_init (hdev=0x563989cf7bd8,
opaque=0x563989cf7e30, backend_type=VHOST_BACKEND_TYPE_USER,
busyloop_timeout=0)
at hw/virtio/vhost.c:1385
#4 0x0000563985f7d0b8 in vhost_user_blk_connect (dev=0x563989cf7990)
at hw/block/vhost-user-blk.c:315
#5 0x0000563985f7d3f6 in vhost_user_blk_event (opaque=0x563989cf7990,
event=CHR_EVENT_OPENED)
at hw/block/vhost-user-blk.c:379
Update the vhost-user-blk device with the internal started_vu field which
will be used for initialization (vhost_user_blk_start) and clean up
(vhost_user_blk_stop). This additional flag in the VhostUserBlk structure
will be used to track whether the device really needs to be stopped and
cleaned up on a vhost-user level.
The disconnect event will set the overall VHOST device (not vhost-user) to
the stopped state, so it can be used by the general vhost_migration_log
routine.
Such approach could be propogated to the other vhost-user devices, but
better idea is just to make the same connect/disconnect code for all the
vhost-user devices.
This migration issue was slightly discussed earlier:
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg01509.html
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg05241.html
Signed-off-by: Dima Stepanov <dimastep@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <9fbfba06791a87813fcee3e2315f0b904cc6789a.1599813294.git.dimastep@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To speed up the memory mapping updating between vhost-vDPA and vDPA
device driver, this patch passes the IOTLB batching flags via IOTLB
API. Two new flags was introduced, VHOST_IOTLB_BATCH_BEGIN is a hint
that a bathced IOTLB updating may be initiated from the
userspace. VHOST_IOTLB_BATCH_END is a hint that userspace has finished
the updating:
VHOST_IOTLB_BATCH_BEGIN
VHOST_IOTLB_UPDATE/VHOST_IOTLB_INVALIDATE
...
VHOST_IOTLB_BATCH_END
Vhost-vDPA can then know that all mappings has been set and can do
optimization like passing all the mappings to the vDPA device driver.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200907104903.31551-4-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch tries to switch to use new kernel IOTLB format V2. Previous
version may have inconsistent ABI between 32bit and 64bit machines
because of the hole after type field. Refer kernel commit
("429711aec282 vhost: switch to use new message format") for more
information.
To enable this feature, qemu need to use a new ioctl
VHOST_SET_BACKEND_FEATURE with VHOST_BACKEND_F_IOTLB_MSG_V2 bit. A new
vhost setting backend features ops was introduced. And when we try to
set features for vhost dev, we will examine the support of new IOTLB
format and enable it. This process is total transparent to guest,
which means we can have different IOTLB message type in src and dst
during migration.
The conversion of IOTLB message is straightforward, just check the
type and behave accordingly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200907104903.31551-3-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fuzzing discovered that virtqueue_unmap_sg() is being called on modified
req->in/out_sg iovecs. This means dma_memory_map() and
dma_memory_unmap() calls do not have matching memory addresses.
Fuzzing discovered that non-RAM addresses trigger a bug:
void address_space_unmap(AddressSpace *as, void *buffer, hwaddr len,
bool is_write, hwaddr access_len)
{
if (buffer != bounce.buffer) {
^^^^^^^^^^^^^^^^^^^^^^^
A modified iov->iov_base is no longer recognized as a bounce buffer and
the wrong branch is taken.
There are more potential bugs: dirty memory is not tracked correctly and
MemoryRegion refcounts can be leaked.
Use the new iov_discard_undo() API to restore elem->in/out_sg before
virtqueue_push() is called.
Fixes: 827805a249 ("virtio-blk: Convert VirtIOBlockReq.out to structrue")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Buglink: https://bugs.launchpad.net/qemu/+bug/1890360
Message-Id: <20200917094455.822379-3-stefanha@redhat.com>
One of the goals of having less boilerplate on QOM declarations
is to avoid human error. Requiring an extra argument that is
never used is an opportunity for mistakes.
Remove the unused argument from OBJECT_DECLARE_TYPE and
OBJECT_DECLARE_SIMPLE_TYPE.
Coccinelle patch used to convert all users of the macros:
@@
declarer name OBJECT_DECLARE_TYPE;
identifier InstanceType, ClassType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_TYPE(InstanceType, ClassType,
- lowercase,
UPPERCASE);
@@
declarer name OBJECT_DECLARE_SIMPLE_TYPE;
identifier InstanceType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_SIMPLE_TYPE(InstanceType,
- lowercase,
UPPERCASE);
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200916182519.415636-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reference it via ops pointer instead, simliar to the vga one.
Removes hard symbol reference, needed to build virtio-gpu modular.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20200914134224.29769-6-kraxel@redhat.com
Separate run of the TypeCheckMacro converter using the --force
flag, for the cases where typedefs weren't found in the same
header nor in typedefs.h.
Generated initially using:
$ ./scripts/codeconverter/converter.py --force -i \
--pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')
Then each case was manually reviewed, and a comment was added
indicating what's unusual about those type checking
macros/functions. Despite not following the usual pattern, the
changes in this patch were found to be safe.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200831210740.126168-15-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-36-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the VHOST_USER_GPU type checking macro to virtio-gpu.h,
close to the TYPE_VHOST_USER_GPU #define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-30-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Automatically size the number of request virtqueues to match the number
of vCPUs. This ensures that completion interrupts are handled on the
same vCPU that submitted the request. No IPI is necessary to complete
an I/O request and performance is improved. The maximum number of MSI-X
vectors and virtqueues limit are respected.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20200818143348.310613-8-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
