Support a following SPI flashes:
* mx66l51235f
* mt25ql512ab
Signed-off-by: Igor Kononenko <i.kononenko@yadro.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200811203724.20699-1-i.kononenko@yadro.com>
Message-Id: <20200819100956.2216690-22-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The mx25l25635e returns the JEDEC ID twice when issuing a RDID command :
[ 2.512027] aspeed-smc 1e630000.spi: reading JEDEC ID C2:20:19:C2:20:19
This can break some firmware testing for this condition on the
supermicrox11-bmc machine.
Reported-by: Erik Smit <erik.lucas.smit@gmail.com>
Message-Id: <20200819100956.2216690-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Whenever an unsupported command is encountered, the current code
interprets each transferred byte as new command. Most of the time, those
'commands' are interpreted as new unknown commands. However, in rare
cases, it may be that for example address or length information
passed with the original command is by itself a valid command.
If that happens, the state machine may get completely confused and,
worst case, start writing data into the flash or even erase it.
To avoid the problem, transition into STATE_READING_DATA and keep
sending a value of 0 until the chip is deselected after encountering
an unsupported command.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When requesting JEDEC data using the JEDEC_READ command, the Linux kernel
always requests 6 bytes. The current implementation only returns three
bytes, and interprets the remaining three bytes as new commands.
While this does not matter most of the time, it is at the very least
confusing. To avoid the problem, always report up to 6 bytes of JEDEC
data. Fill remaining data with 0.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While at it, add some trace messages to help debug problems
seen when running the latest Linux kernel.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-20-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180625124238.25339-14-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On Macronix chips, two bytes can written to the WRSR. First byte will
configure the status register and the second the configuration
register. It is important to save the configuration value as it
contains the dummy cycle setting when using dual or quad IO mode.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove those unneeded includes to speed up the compilation
process a little bit.
Code change produced with:
$ git grep '#include "sysemu/blockdev.h"' | \
cut -d: -f-1 | \
xargs egrep -L "(BlockInterfaceType|DriveInfo|drive_get|blk_legacy_dinfo|blockdev_mark_auto_del)" | \
xargs sed -i.bak '/#include "sysemu\/blockdev.h"/d'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-15-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The point of writing a macro embedded in a 'do { ... } while (0)'
loop (particularly if the macro has multiple statements or would
otherwise end with an 'if' statement) is so that the macro can be
used as a drop-in statement with the caller supplying the
trailing ';'. Although our coding style frowns on brace-less 'if':
if (cond)
statement;
else
something else;
that is the classic case where failure to use do/while(0) wrapping
would cause the 'else' to pair with any embedded 'if' in the macro
rather than the intended outer 'if'. But conversely, if the macro
includes an embedded ';', then the same brace-less coding style
would now have two statements, making the 'else' a syntax error
rather than pairing with the outer 'if'. Thus, even though our
coding style with required braces is not impacted, ending a macro
with ';' makes our code harder to port to projects that use
brace-less styles.
The change should have no semantic impact. I was not able to
fully compile-test all of the changes (as some of them are
examples of the ugly bit-rotting debug print statements that are
completely elided by default, and I didn't want to recompile
with the necessary -D witnesses - cleaning those up is left as a
bite-sized task for another day); I did, however, audit that for
all files touched, all callers of the changed macros DID supply
a trailing ';' at the callsite, and did not appear to be used
as part of a brace-less conditional.
Found mechanically via: $ git grep -B1 'while (0);' | grep -A1 \\\\
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171201232433.25193-7-eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support for Micron (Numonyx) n25q512a11 and n25q512a13 flashes.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-5-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the bank address register access commands (BRRD/BRWR) and
the BULK_ERASE (0x60) command.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-4-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for SST READ ID 0x90/0xAB commands for reading out the flash
manufacturer ID and device ID.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20171126231634.9531-3-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for continuous read out of the RDSR and READ_FSR status
registers until the chip select is deasserted. This feature is supported
by amongst others 1 or more flashtypes manufactured by Numonyx (Micron),
Windbond, SST, Gigadevice, Eon and Macronix.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Marcin Krzemiński<mar.krzeminski@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-2-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This makes all device emulations with a qdev drive property request
permissions on their BlockBackend. The only thing we block at this point
is resizing images for some devices that can't support it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
n25q00 and mt25q01 devices share the same JEDEC ID. The difference
between those two devices is number of dies and one bit in extended
JEDEC bytes. This commit adds proper entry for both devices by
introduction the number of dies and and new 25q00 entries.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-4-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modern big flash NOR devices consist of more than one die.
Some of them do not support chip erase and instead have a die
erase command that can erase one die only. This commit adds
support for defining the number of dies in the chip, and adds
support for die erase command.
The NOR flash model is not strict, so no option to
disable chip erase has been added.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-3-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some flash chips have additional page program opcode that
takes only 4 byte address. This commit adds support
for such command in Qemu.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-2-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In normal operation we should never attempt to put more
data into the data[] array than it can hold. However if the
SPI controller connected to us misbehaves then it can send
us a sequence of commands that attempt this. Since the
controller might be in the guest (if the hardware does SPI
via bit-banging), catch the possible overrun conditions and
reset the flash internal state, logging them as guest errors.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 20170107111631.24444-1-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: rewrote commit message to be more exact about when
this can happen]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Correct bad name of the vmstate structure. Since this breaks
compatibility also update vmstate version back to 0 and make
all fields independent of the VMState version.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1473146346-27337-1-git-send-email-marcin.krzeminski@nokia.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Winbond also support continuous read mode, but as an opposite for other
flash type read mode clock cycles are included to dummy cycles number.
This path add proper handling of read mode byte and update needed
dummy cycles. QPI mode and dummy cycles configuration are not supported.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467809036-6986-1-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These two are spot by Coverity 1357232 and 1357233.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1467684998-12076-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows specifying the property via -drive if=none and creating
the flash device with -device.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-6-git-send-email-clg@kaod.org
[clg: added an extra fix for sabrelite_init()
keeping the test on flash_dev did not seem necessary. ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The maximum amount of storage that can be addressed by the m25p80 command
set is 4 GiB. However, cur_addr is currently a 64-bit integer. To avoid
further problems related to sign extension of signed 32-bit integer
expressions, change cur_addr to a 32 bit integer. Preserve migration
format by adding a dummy 4-byte field in place of the (big-endian)
high four bytes in the formerly 64-bit cur_addr field.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
s->cur_addr can be made to point outside s->storage, either by
writing a value >= 128 to s->ear (because s->ear * MAX_3BYTES_SIZE
is a signed integer and sign-extends into the 64-bit cur_addr),
or just by writing an address beyond the size of the flash being
emulated. Avoid the sign extension to make the code cleaner, and
on top of that mask s->cur_addr to s->size.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-4-git-send-email-clg@kaod.org
Reviewed by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing a read-modify-write cycle, QEMU uses the iovec after returning
from blk_aio_pwritev. m25p80 puts the iovec on the stack of blk_aio_pwritev's
caller, which causes trouble in this case. This has been a problem
since commit 243e6f6 ("m25p80: Switch to byte-based block access",
2016-05-12) started doing writes at a smaller granularity than 512 bytes.
In principle however it could have broken before when using -drive
if=mtd,cache=none on a disk with 4K native sectors.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables qemu to handle late inits and report errors. All the SSI
slave routine names were changed accordingly. Code was modified to
handle errors when possible (m25p80 and ssi-sd)
Tested with the m25p80 slave object.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit fix obvious bug in WINBOND command handling.
Datasheet states that default dummy cycles is 8 so fix it.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Message-id: 1466755631-25201-11-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Macronix: mx66u51235f and mx66u1g45g
Micron: mt25ql01g and mt25qu01g
Spansion: s25fs512s and s70fs01gs
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-10-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support for Spansion and Macronix flashes.
Additionally Numonyx(Micron) moved from default
in fast read commands family. Also moved fast read
command decoding to functions.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-9-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Configuration registers for Spansion and Macronix devices.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-8-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Quad and Equad modes for Spansion and Macronix flash devices.
This commit also includes modification and new command to manipulate
quad mode (status registers and dedicated commands).
This work is based on Pawel Lenkow work.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-7-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Page program 4byte/quad and erase 32K sectors 4 bytes.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-6-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some flash allows to stop read at any time.
Allow framework to support this.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-5-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow to have more than four 16MiB regions for bigger flash devices.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-4-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since it is now longer than 4. This work based on Pawel Lenkow
changes and the kernel SPI framework.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-3-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of always reading and comparing jededc ID,
replace it by function.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Message-id: 1466755631-25201-2-git-send-email-marcin.krzeminski@nokia.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 243e6f69c1 ("m25p80: Switch to byte-based block access")
replaced blk_read() calls with blk_pread() but return values are
different.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based blk_read() should die; switch to byte-based
blk_pread() instead.
Likewise for blk_aio_readv() and blk_aio_writev().
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-12-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
