In the SDHCI protocol, the transfer mode register value
is used during multi block transfer to check if block count
register is enabled and should be updated. Transfer mode
register could be set such that, block count register would
not be updated, thus leading to an infinite loop. Add check
to avoid it.
Reported-by: Wjjzhang <wjjzhang@tencent.com>
Reported-by: Jiang Xin <jiangxin1@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20170214185225.7994-3-ppandit@redhat.com
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In SDHCI protocol, the transfer mode register is defined
to be of 6 bits. Mask its value with '0x0037' so that an
invalid value could not be assigned.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20170214185225.7994-2-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The member VMStateField.start is used for two things, partial data
migration for VBUFFER data (basically provide migration for a
sub-buffer) and for locating next in QTAILQ.
The implementation of the VBUFFER feature is broken when VMSTATE_ALLOC
is used. This however goes unnoticed because actually partial migration
for VBUFFER is not used at all.
Let's consolidate the usage of VMStateField.start by removing support
for partial migration for VBUFFER.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170203175217.45562-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
While doing multi block SDMA transfer in routine
'sdhci_sdma_transfer_multi_blocks', the 's->fifo_buffer' starting
index 'begin' and data length 's->data_count' could end up to be same.
This could lead to an OOB access issue. Correct transfer data length
to avoid it.
Cc: qemu-stable@nongnu.org
Reported-by: Jiang Xin <jiangxin1@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20170130064736.9236-1-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Changed a few types to fixed sized types in the ssi_sd_state
Now saving/loading a byte for the cmdarg/response bytes that were
previously saved as uint32
Bumped version number to deal with those changes.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1472035246-12483-4-git-send-email-dgilbert@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Free the timer allocated in instance_init.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
This enables qemu to handle late inits and report errors. All the SSI
slave routine names were changed accordingly. Code was modified to
handle errors when possible (m25p80 and ssi-sd)
Tested with the m25p80 slave object.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/sd/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-23-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The old milkymist.org domain just forwards to mm-labs.hk nowadays. I've
created a mirror of the documents.
Signed-off-by: Michael Walle <michael@walle.cc>
split the old SysBus init function into an instance_init
and a Device realize function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-13-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Sector-based blk_write() should die; switch to byte-based
blk_pwrite() instead. Likewise for blk_read().
Greatly simplifies the code, now that we let the block layer
take care of alignment and read-modify-write on our behalf :)
In fact, we no longer need to include 'buf' in the migration
stream (although we do have to ensure that the stream remains
compatible).
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SD card object is not a SysBusDevice, so don't create it with
qdev_create() if we're not assigning it to a specific bus; use
object_new() instead.
This was causing 'info qtree' to segfault on boards with SD cards,
because qdev_create(NULL, TYPE_FOO) puts the created object on the
system bus, and then we may try to run functions like sysbus_dev_print()
on it, which fail when casting the object to SysBusDevice.
(This is the same mistake that we made with the NAND device
and fixed in commit 6749695eaaf346c1.)
Reported-by: xiaoqiang.zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: xiaoqiang.zhao <zxq_yx_007@163.com>
Message-id: 1458061009-7733-1-git-send-email-peter.maydell@linaro.org
The sdhci device was missing a DeviceClass reset method;
implement it. Poweron reset looks the same as reset commanded
by the guest via the device registers, apart from modelling of
the rpi 'pending insert interrupt on powerup' quirk.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456493044-10025-3-git-send-email-peter.maydell@linaro.org
The sd.c SD card emulation code can be in a state where the
SDState BlockBackend pointer is NULL; this is treated as
"card not present". Add a missing check to sd_get_inserted()
so that we don't segfault in this situation.
(This could be provoked by the guest writing to the SDHCI
register to do a reset on a xilinx-zynq-a9 board; it will
also happen at startup when sdhci implements its DeviceClass
reset method.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1456493044-10025-2-git-send-email-peter.maydell@linaro.org
This quirk is a workaround for the following hardware behaviour, on
which UEFI (specifically, the bootloader for Windows on Pi2) depends:
1. at boot with an SD card present, the interrupt status/enable
registers are initially zero
2. upon enabling it in the interrupt enable register, the card insert
bit in the interrupt status register is immediately set
3. after a subsequent controller reset, the card insert interrupt does
not fire, even if enabled in the interrupt enable register
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-3-git-send-email-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 723697551a.
This change was poorly tested on my part. It squelched card insertion
interrupts on reset, but that was not necessary because sdhci_reset()
clears all the registers (via the call to memset), so the subsequent
sdhci_insert_eject_cb() call never sees the card insert interrupt
enabled. However, not calling the insert_eject_cb results in prnsts
remaining 0, when it actually needs to be updated to indicate card
presence and R/O status.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-2-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some of these errors may be harmless (e.g. probing unimplemented
commands, or issuing CMD12 in the wrong state), and may also be quite
frequent. Spamming the standard error output isn't desirable in such
cases.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454902521-21164-4-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SD spec for ACMD41 says that a zero argument is an "inquiry"
ACMD41, which does not start initialisation and is used only for
retrieving the OCR. However, Tianocore EDK2 (UEFI) has a bug [1]: it
first sends an inquiry (zero) ACMD41. If that first request returns an
OCR value with the power up bit (0x80000000) set, it assumes the card
is ready and continues, leaving the card in the wrong state. (My
assumption is that this works on hardware, because no real card is
immediately powered up upon reset.)
This change models a delay of 0.5ms from the first ACMD41 to the power
being up. However, it also immediately sets the power on upon seeing a
non-zero (non-enquiry) ACMD41. This speeds up UEFI boot, it should
also account for guests that simply delay after card reset and then
issue an ACMD41 that they expect will succeed.
[1] https://github.com/tianocore/edk2/blob/master/EmbeddedPkg/Universal/MmcDxe/MmcIdentification.c#L279
(This is the loop starting with "We need to wait for the MMC or SD
card is ready")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454902521-21164-3-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CMD23 is optional for SD but required for MMC, and the UEFI bootloader
used for Windows on Raspberry Pi 2 issues it.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454902521-21164-2-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a reset function to the pxa2xx_mmci device; previously it had
no handling for system reset at all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-11-git-send-email-peter.maydell@linaro.org
Convert the pxa2xx_mmci device from manual save/load
functions to a VMStateDescription structure.
This is a migration compatibility break.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-10-git-send-email-peter.maydell@linaro.org
Now the PXA2xx MMCI device is QOMified itself, we can
update it to use the SDBus APIs to talk to the SD card.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455646193-13238-9-git-send-email-peter.maydell@linaro.org
Convert the pxa2xx_mmci device to be a sysbus device.
In this commit we only change the device itself, and leave
the interface to the SD card using the old non-SDBus APIs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-8-git-send-email-peter.maydell@linaro.org
Move the creation of the SD card device from the sdhci_sysbus
device itself into the boards that create these devices.
This allows us to remove the cannot_instantiate_with_device_add
notation because we no longer call drive_get_next in the device
model.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-7-git-send-email-peter.maydell@linaro.org
Update the SDHCI code to use the new SDBus APIs.
This commit introduces the new command line options required
to connect a disk to sdhci-pci:
-device sdhci-pci -drive id=mydrive,[...] -device sd,drive=mydrive
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-6-git-send-email-peter.maydell@linaro.org
Add a QOM bus for SD cards to plug in to.
Note that since sd_enable() is used only by one board and there
only as part of a broken implementation, we do not provide it in
the SDBus API (but instead add a warning comment about the old
function). Whoever converts OMAP and the nseries boards to QOM
will need to either implement the card switch properly or move
the enable hack into the OMAP MMC controller model.
In the SDBus API, the old-style use of sd_set_cb to register some
qemu_irqs for notification of card insertion and write-protect
toggling is replaced with methods in the SDBusClass which the
card calls on status changes and methods in the SDClass which
the controller can call to find out the current status. The
query methods will allow us to remove the abuse of the 'register
irqs' API by controllers in their reset methods to trigger
the card to tell them about the current status again.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-5-git-send-email-peter.maydell@linaro.org
Convert the sd_reset() function into a proper Device reset method.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-4-git-send-email-peter.maydell@linaro.org
Turn the SD card into a QOM device.
This conversion only changes the device itself; the various
functions which are effectively methods on the device are not
touched at this point.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-3-git-send-email-peter.maydell@linaro.org
The following commits will remove support for the old sdhci-pci
command line syntax using the x-drive property:
-device sdhci-pci,x-drive=mydrive -drive id=mydrive,[...]
and replace it with an explicit sd device:
-device sdhci-pci -drive id=mydrive,[...] -device sd,drive=mydrive
(This is OK because x-drive is experimental.)
This commit removes the x-drive property so that old style
command lines will fail with a reasonable error message:
-device sdhci-pci,x-drive=mydrive: Property '.x-drive' not found
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1455646193-13238-2-git-send-email-peter.maydell@linaro.org
While processing standard SD commands, the 'req.cmd' value could
lead to OOB read when used as an index into 'sd_cmd_type' or
'sd_cmd_class' arrays. Limit 'req.cmd' value to avoid such an
access.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453315857-1352-1-git-send-email-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-38-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-36-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-5-git-send-email-peter.maydell@linaro.org
Move the ssi.h include file into the ssi directory.
While touching the code also fix the typdef lines as
checkpatch complains.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is needed for a quirk of the Raspberry Pi (bcm2835/6) MMC
controller, where the card insert bit is documented as unimplemented
(always reads zero, doesn't generate interrupts) but is in fact
observed on hardware as set at power on, but is cleared (and remains
clear) on subsequent controller resets.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1450738069-18664-4-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This deletes a block of code that raised a command index error if a
command returned response data, but the guest did not set the
appropriate bits in the response register to handle such a response. I
cannot find any documentation that suggests the controller should
behave in this way, the error code doesn't make sense (command index
error is defined for the case where the index in a response does not
match that of the issued command), and in at least one case (CMD23
issued by UEFI on Raspberry Pi 2), actual hardware does not do this.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1450738069-18664-3-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This check was conditionalising SD card operation on the card being
powered by the SDHCI host controller. It is however possible
(particularly in embedded systems) for the power control of the SD card
to be managed outside of SDHCI. This can be as trivial as hard-wiring
the SD slot VCC to a constant power-rail.
This means the guest SDHCI can validly opt-out of the SDHCI power
control feature while still using the card. So delete this check to
allow operation of the card with SDHCI power control.
This is needed for at least Xilinx Zynq and Raspberry Pi, and
also makes Freescale i.MX25 work for me. The digilent Zybo board
has a public schematic which shows SD VCC hardwiring:
http://digilentinc.com/Data/Products/ZYBO/ZYBO_sch_VB.3.pdf
bottom of page 3.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1450738069-18664-2-git-send-email-Andrew.Baumann@microsoft.com
[AB: Add Pi to list of devices fixed in commit message]
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
blk_attach_dev() fails here only when we're working for device
"sdhci-pci" (which already attached the backend), and then we don't
want to attach a second time. If we ever create another failure mode,
we're setting up ourselves to using the same backend from multiple
frontends, which is likely to end in tears. Can't clean this up this
close to the release, so mark it FIXME.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1449503710-3707-3-git-send-email-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We currently fuse controller and card into a single device model, but
we intend qomify things properly and separate the two. The properties
that really belong to the card would then have to somehow pass-through
to the card's properties. To avoid that complication, either mark
them experimental or drop them.
Properties "capareg", "maxcurr" and the usual PCI device properties
belong to the controller. Property "drive" belongs to the card;
rename it to "x-drive". Properties "logical_block_size",
"physical_block_size", "min_io_size", "opt_io_size",
"discard_granularity" belong to the card, but have no effect; drop
them.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1449503710-3707-2-git-send-email-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Split sdhci.h into pubilc version (i.e include/hw/sd/sdhci.h) and
internal version (i.e hw/sd/sdhci-interna.h) based on register
declarations and object declaration.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Create a sd directory under include/hw/ and move sd.h to
include/hw/sd/
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is possible for the guest to set an invalid block
size which is larger then the fifo_buffer[] array. This
could cause a buffer overflow.
To avoid this limit the maximum size of the blksize variable.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Intel Security ATR <secure@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: abe4c51f513290bbb85d1ee271cb1a3d463d7561.1444067470.git.alistair.francis@xilinx.com
Suggested-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Reported-by: Intel Security ATR <secure@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 19109131 disabled the sdhci-pci support because it used
drive_get_next(). This patch reenables sdhci-pci and changes it to
pass the drive via a qdev property - for example:
-device sdhci-pci,drive=drive0 -drive id=drive0,if=sd,file=myimage
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Conditional compilation hides few type mismatch warnings, fix it to
compile unconditionally.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Suggested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fix compile time warnings, because of type mismatch for unsigned long
long type.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
My Coccinelle semantic patch finds a few more, because it also fixes up
the equally pointless conditional
if (foo) {
free(foo);
foo = NULL;
}
Result (feel free to squash it into your patch):
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The free() and g_free() functions both happily accept
NULL on any platform QEMU builds on. As such putting a
conditional 'if (foo)' check before calls to 'free(foo)'
merely serves to bloat the lines of code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Update the pxa2xx_mmci device to stop using the old_mmio read
and write callbacks in its MemoryRegionOps. This actually
simplifies the code because the separate byte/halfword/word
access functions were all calling into a single function to
do the work anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1434117989-7367-6-git-send-email-peter.maydell@linaro.org
The only valid BlockBackend to pass to sd_reset() is the one for
the SD card, which is sd->blk. Drop the second argument from this
function in favour of having it just use sd->blk.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1430683444-9797-1-git-send-email-peter.maydell@linaro.org
ffs() cannot be replaced with ctz32() when the argument might be zero,
because ffs(0) returns 0 while ctz32(0) returns 32.
The ffs(3) call in sd_normal_command() is a special case though. It can
be converted to ctz32() + 1 because the argument is never zero:
if (!(req.arg >> 8) || (req.arg >> (ctz32(req.arg & ~0xff) + 1))) {
~~~~~~~~~~~~~~~
^--------------- req.arg cannot be zero
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-7-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Device models aren't supposed to go on fishing expeditions for
backends. They should expose suitable properties for the user to set.
For onboard devices, board code sets them.
A number of sysbus devices pick up block backends in their init() /
instance_init() methods with drive_get_next() instead: sl-nand,
milkymist-memcard, pl181, generic-sdhci.
Likewise, a number of sysbus devices pick up character backends in
their init() / realize() methods with qemu_char_get_next_serial():
cadence_uart, digic-uart, etraxfs,serial, lm32-juart, lm32-uart,
milkymist-uart, pl011, stm32f2xx-usart, xlnx.xps-uartlite.
All these mistakes are already marked FIXME. See the commit that
added these FIXMEs for a more detailed explanation of what's wrong.
Fortunately, only machines ppce500 and pseries-* support -device with
sysbus devices, and none of the devices above is supported with these
machines.
Set cannot_instantiate_with_device_add_yet to preserve our luck.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Device models aren't supposed to go on fishing expeditions for
backends. They should expose suitable properties for the user to set.
For onboard devices, board code sets them.
"sdhci-pci" picks up its block backend in its realize() method with
drive_get_next() instead. Already marked FIXME. See the commit that
added the FIXME for a more detailed explanation of what's wrong.
We can't fix this in time for the release, but since the device is new
in 2.3, we can set cannot_instantiate_with_device_add_yet to disable
it before this mistake becomes ABI, and we have to support command
lines like
$ qemu -drive if=sd -drive if=sd,file=sd.img -device sdhci-pci -device sdhci-pci
forever.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Drives defined with if!=none are for board initialization to wire up.
Board code calls drive_get() or similar to find them, and creates
devices with their qdev drive properties set accordingly.
Except a few devices go on a fishing expedition for a suitable backend
instead of exposing a drive property for board code to set: they call
driver_get() or drive_get_next() in their realize() or init() method
to implicitly connect to the "next" backend with a certain interface
type.
Picking up backends that way works when the devices are created by
board code. But it's inappropriate for -device or device_add. Not
only is this inconsistent with how the other block device models work
(they connect to a backend explicitly identified by a "drive"
property), it breaks when the "next" backend has been picked up by the
board already.
Example:
$ qemu-system-arm -S -M connex -pflash flash.img -device ssi-sd
Aborted (core dumped)
Mark them with suitable FIXME comments.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: "Andreas Färber" <andreas.faerber@web.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Convert the device models where initialization obviously can't fail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Support for PCI devices following the "SD Host Controller Simplified
Specification Version 2.00" spec.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the sdhci sysbus QOM types and methods so that sysbus is in
their name. This is in preparation for adding PCI versions of these
types and methods.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SDHCIClass defines a series of class "methods". However, no code
in the QEMU tree overrides these methods or even uses them outside of
sdhci.c.
Remove the virtual methods and replace them with direct calls to the
underlying functions. This simplifies the process of extending the
sdhci code to support PCI devices (which have a different parent
class).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Linux SDHCI PCI driver will only register the device if there is a
clock frequency set. So, set a default frequency of 52Mhz.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The patch is big, but all it really does is replacing
dinfo->bdrv
by
blk_bs(blk_by_legacy_dinfo(dinfo))
The replacement is repetitive, but the conversion of device models to
BlockBackend is imminent, and will shorten it to just
blk_legacy_dinfo(dinfo).
Line wrapping muddies the waters a bit. I also omit tests whether
dinfo->bdrv is null, because it never is.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Benoît Canet <benoit.canet@nodalink.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This dma_memory_read was giving too big a size when begin was non-zero.
This could cause segfaults in some circumstances. Fix.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace qemu_allocate_irqs(foo, bar, 1)[0]
with qemu_allocate_irq(foo, bar, 0).
This avoids leaking the dereferenced qemu_irq *.
Cc: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
[PC Changes:
* Applied change to instance in sh4/sh7750.c
]
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Kirill Batuzov <batuzovk@ispras.ru>
[AF: Fix IRQ index in sh4/sh7750.c]
Cc: qemu-stable@nongnu.org
Signed-off-by: Andreas Färber <afaerber@suse.de>
It does a g_free() on the pointer, so don't pass a local &foo reference.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Andreas Färber <afaerber@suse.de>
Drop the sd_acmd_type[] array: it is never used. (The equivalent
sd_cmd_type[] array for normal commands is used to identify
those commands whose argument includes the card address in the
top 16 bits; but for app commands the card address is passed
with the APP_CMD prefix, not with the argument to the app command
itself.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
CVE-2013-4537
s->arglen is taken from wire and used as idx
in ssi_sd_transfer().
Validate it before access.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Convert legacy ->qdev style casts from TYPE_SSI_SLAVE to TYPE_DEVICE.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[AF: Introduce local DeviceState variable for transition to QOM realize]
Signed-off-by: Andreas Färber <afaerber@suse.de>
* QTest cleanups and test cases for PCI NICs
* NAND fix for "info qtree"
* Cleanup and extension of QOM machine tests
* IndustryPack test cases and conversion to QOM realize
* I2C cleanups
* Cleanups of legacy qdev properties
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=KRcc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/afaerber/tags/qom-devices-for-peter' into staging
QOM infrastructure fixes and device conversions
* QTest cleanups and test cases for PCI NICs
* NAND fix for "info qtree"
* Cleanup and extension of QOM machine tests
* IndustryPack test cases and conversion to QOM realize
* I2C cleanups
* Cleanups of legacy qdev properties
# gpg: Signature made Mon 17 Feb 2014 22:15:37 GMT using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
* remotes/afaerber/tags/qom-devices-for-peter: (49 commits)
qtest: Include system headers before user headers
qapi: Refine human printing of sizes
qdev: Use QAPI type names for properties
qdev: Add enum property types to QAPI schema
block: Handle "rechs" and "large" translation options
qdev: Remove hex8/32/64 property types
qdev: Remove most legacy printers
qdev: Use human mode in "info qtree"
qapi: Add human mode to StringOutputVisitor
qdev: Inline qdev_prop_parse()
qdev: Legacy properties are just strings
qdev: Legacy properties are now read-only
qdev: Remove legacy parsers for hex8/32/64
qdev: Sizes are now parsed by StringInputVisitor
qapi: Add size parser to StringInputVisitor
qtest: Don't segfault with invalid -qtest option
ipack: Move IndustryPack out of hw/char/
ipoctal232: QOM parent field cleanup
ipack: QOM parent field cleanup for IPackDevice
ipack: QOM parent field cleanup for IPackBus
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace them with uint8/32/64.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
device_add plugs devices into suitable bus. For "real" buses, that
actually connects the device. For sysbus, the connections need to be
made separately, and device_add can't do that. The device would be
left unconnected, and could not possibly work.
Quite a few, but not all sysbus devices already set
cannot_instantiate_with_device_add_yet in their class init function.
Set it in their abstract base's class init function
sysbus_device_class_init(), and remove the now redundant assignments
from device class init functions.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
In an ideal world, machines can be built by wiring devices together
with configuration, not code. Unfortunately, that's not the world we
live in right now. We still have quite a few devices that need to be
wired up by code. If you try to device_add such a device, it'll fail
in sometimes mysterious ways. If you're lucky, you get an
unmysterious immediate crash.
To protect users from such badness, DeviceClass member no_user used to
make device models unavailable with -device / device_add, but that
regressed in commit 18b6dad. The device model is still omitted from
help, but is available anyway.
Attempts to fix the regression have been rejected with the argument
that the purpose of no_user isn't clear, and it's prone to misuse.
This commit clarifies no_user's purpose. Anthony suggested to rename
it cannot_instantiate_with_device_add_yet_due_to_internal_bugs, which
I shorten somewhat to keep checkpatch happy. While there, make it
bool.
Every use of cannot_instantiate_with_device_add_yet gets a FIXME
comment asking for rationale. The next few commits will clean them
all up, either by providing a rationale, or by getting rid of the use.
With that done, the regression fix is hopefully acceptable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Commit 4f8a066b5f (blockdev: Remove IF_*
check for read-only blockdev_init) added a usage of bdrv_is_read_only()
to sd_init(), which is called for versatilepb, versatileab and
xilinx-zynq-a9 machines among others with NULL argument by default,
causing the new qom-test to fail.
Add a check to prevent this.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
IF_NONE allows read-only, which makes forbidding it in this place
for other types pretty much pointless.
Instead, make sure that all devices for which the check would have
errored out check in their init function that they don't get a read-only
BlockDriverState. This catches even cases where IF_NONE and -device is
used.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a cast to avoid potentially shifting into the sign bit of
a signed value, which is undefined behaviour in C.
(Detected with clang's -fsanitize=undefined.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1372341831-4264-1-git-send-email-peter.maydell@linaro.org
The DMAContext is a simple pointer to an AddressSpace that is now always
already available. Make everyone hold the address space directly,
and clean up the DMA API to use the AddressSpace directly.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
QEMU models two (of the three) ACMD41 has two modes, "inquiry" and
"first". The selection logic for which of the two is incorrect - it
compares != 0 for the entire argument value rather than only bits 23:0
as per the spec. Fix.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 3ef0a7fd1b2f3ebb23b4fdeabcc14caf3fad6d71.1369622254.git.peter.crosthwaite@xilinx.com
Reviewed-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The end of transfer check was occurring and potentially returning before
the interrupt flag was checked. This means the interrupt will be missed
if it occurs on the last packet. Fix by checking for the interrupt
before checking for the end of transfer.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Message-id: 9969ec154777957ec738fc4e539d68e7494d0081.1369370934.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This message was printing out the data in decimal only, which is not
very friendly to the debugging developer. Add hex variant in
parenthesis to make it consistent with other similar messages in this
module.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: d624179649137832eaa8caa263ef9589b4395d5e.1369370934.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This interrupt is not risen after the last block is written to sd. It
is mutually exclusive with the end of transfer conditions. Fix.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Message-id: 7ca9fd3e03ce1bec94aff08f607c15a0ec3d3371.1369370934.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The data_count variable was being reset on every transfer, including
DMA transfer resumptions. This is incorrect, it should only be set
on a new command.
Manifests as a bug when using ADMA and there is a timer delay between
ADMA frames where the fifo is left in a non empty state.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Message-id: 15a98609cc32315211b0963091a8efd67522e160.1369370934.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Minor fixes to documentation and code comments.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
