The point of writing a macro embedded in a 'do { ... } while (0)'
loop (particularly if the macro has multiple statements or would
otherwise end with an 'if' statement) is so that the macro can be
used as a drop-in statement with the caller supplying the
trailing ';'. Although our coding style frowns on brace-less 'if':
if (cond)
statement;
else
something else;
that is the classic case where failure to use do/while(0) wrapping
would cause the 'else' to pair with any embedded 'if' in the macro
rather than the intended outer 'if'. But conversely, if the macro
includes an embedded ';', then the same brace-less coding style
would now have two statements, making the 'else' a syntax error
rather than pairing with the outer 'if'. Thus, even though our
coding style with required braces is not impacted, ending a macro
with ';' makes our code harder to port to projects that use
brace-less styles.
The change should have no semantic impact. I was not able to
fully compile-test all of the changes (as some of them are
examples of the ugly bit-rotting debug print statements that are
completely elided by default, and I didn't want to recompile
with the necessary -D witnesses - cleaning those up is left as a
bite-sized task for another day); I did, however, audit that for
all files touched, all callers of the changed macros DID supply
a trailing ';' at the callsite, and did not appear to be used
as part of a brace-less conditional.
Found mechanically via: $ git grep -B1 'while (0);' | grep -A1 \\\\
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171201232433.25193-7-eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For a couple of macros in pcnet.c, we have to provide a new scope
to avoid compiler warnings about declarations in the middle of a
switch statement that aren't in a sub-scope. But use of
'do { ... } while (0);' merely to provide that new scope is arcane
overkill, compared to just using '{ ... }'.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20171201232433.25193-2-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some i.MX SoCs (e.g. i.MX7) have FEC registers going as far as offset
0x614, so to avoid getting aborts when accessing those on QEMU, extend
the register file to cover FSL_IMX25_FEC_SIZE(16K) of address space
instead of just 1K.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use 'frame_size' instead of 'len' when calling qemu_send_packet(),
failing to do so results in malformed packets send in case when that
packed is fragmented into multiple DMA transactions.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
More recent version of the IP block support more than one Tx DMA ring,
so add the code implementing that feature.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Needed to support latest Linux kernel driver which relies on that
functionality.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Frame truncation length, TRUNC_FL, is determined by the contents of
ENET_FTRL register, so convert the code to use it instead of a
hardcoded constant.
To avoid the case where TRUNC_FL is greater that ENET_MAX_FRAME_SIZE,
increase the value of the latter to its theoretical maximum of 16K.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make Tx frame assembly buffer to be a paort of IMXFECState structure
to avoid a concern about having large data buffer on the stack.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In current implementation, packet queue flushing logic seem to suffer
from a deadlock like scenario if a packet is received by the interface
before before Rx ring is initialized by Guest's driver. Consider the
following sequence of events:
1. A QEMU instance is started against a TAP device on Linux
host, running Linux guest, e. g., something to the effect
of:
qemu-system-arm \
-net nic,model=imx.fec,netdev=lan0 \
netdev tap,id=lan0,ifname=tap0,script=no,downscript=no \
... rest of the arguments ...
2. Once QEMU starts, but before guest reaches the point where
FEC deriver is done initializing the HW, Guest, via TAP
interface, receives a number of multicast MDNS packets from
Host (not necessarily true for every OS, but it happens at
least on Fedora 25)
3. Recieving a packet in such a state results in
imx_eth_can_receive() returning '0', which in turn causes
tap_send() to disable corresponding event (tap.c:203)
4. Once Guest's driver reaches the point where it is ready to
recieve packets it prepares Rx ring descriptors and writes
ENET_RDAR_RDAR to ENET_RDAR register to indicate to HW that
more descriptors are ready. And at this points emulation
layer does this:
s->regs[index] = ENET_RDAR_RDAR;
imx_eth_enable_rx(s);
which, combined with:
if (!s->regs[ENET_RDAR]) {
qemu_flush_queued_packets(qemu_get_queue(s->nic));
}
results in Rx queue never being flushed and corresponding
I/O event beign disabled.
To prevent the problem, change the code to always flush packet queue
when ENET_RDAR transitions 0 -> ENET_RDAR_RDAR.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Refactor imx_eth_enable_rx() to have more meaningfull variable name
than 'tmp' and to reduce number of logical negations done.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Binding to a particular netdev doesn't seem to belong to this layer
and should probably be done as a part of board or SoC specific code.
Convert all of the users of this IP block to use
qdev_set_nic_properties() instead.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With the previous commit there is now nothing left in sun4m.h so it can be
removed, along with all remaining references to it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
This makes it much easier to compare the multicast CRC calculation endian and
bitshift against the Linux driver implementation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This makes it much easier to compare the multicast CRC calculation endian and
bitshift against the Linux driver implementation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This makes it much easier to compare the multicast CRC calculation endian and
bitshift against the Linux driver implementation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This makes it much easier to compare the multicast CRC calculation endian and
bitshift against the Linux driver implementation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This makes it much easier to compare the multicast CRC calculation endian and
bitshift against the Linux driver implementation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This makes it much easier to compare the multicast CRC calculation endian and
bitshift against the Linux driver implementation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Jason Wang <jasowang@redhat.com>
From the Linux sungem driver, we know that the multicast filter CRC is
implemented using ether_crc_le() which isn't the same as calling zlib's
crc32() function (the zlib implementation requires a complemented initial value
and also returns the complemented result).
Fix the multicast filter by simply using the new net_crc32_le() function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Instead of sunhme_crc32_le() using its own implementation, we can simply call
net_crc32_le() directly and apply the bit shift inline.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Instead of e100_compute_mcast_idx() using its own implementation, we can
simply call net_crc32() directly and apply the bit shift inline.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Instead of lnc_mchash() using its own implementation, we can simply call
net_crc32_le() directly and apply the bit shift inline.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Separate out the standard ethernet CRC32 calculation into a new net_crc32()
function, renaming the constant POLYNOMIAL to POLYNOMIAL_BE to make it clear
that this is a big-endian CRC32 calculation.
As part of the constant rename, remove the duplicate definition of POLYNOMIAL
from eepro100.c and use the new POLYNOMIAL_BE constant instead.
Once this is complete remove the existing CRC32 implementation from
compute_mcast_idx() and call the new net_crc32() function in its place.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The device is supposed to maintain two distinct contexts for transmit
offloads: one has parameters for both segmentation and checksum
offload, the other only for checksum offload. The guest driver can
send two context descriptors, one for each context (the TSE flag
specifies which). Then the guest can refer to one or the other context
in subsequent transmit data descriptors, depending on what offloads it
wants applied to each packet.
Currently the e1000 device stores just one context, and misinterprets
the TSE flags in the context and data descriptors. This is often okay:
Linux happens to send a fresh context descriptor before every data
descriptor, so forgetting the other context doesn't matter. Windows
does rely on separate contexts for TSO vs. non-TSO packets, but for
mostly-TCP traffic the two contexts have identical TCP-specific
offload parameters so confusing them doesn't matter.
One case where this confusion matters is when a Windows guest sets up
a TSO context for TCP and a non-TSO context for UDP, and then
transmits both TCP and UDP traffic in parallel. The e1000 device
sometimes ends up using TCP-specific parameters while doing checksum
offload on a UDP datagram: it writes the checksum to offset 16 (the
correct location for a TCP checksum), stomping on two bytes of UDP
data, and leaving the wrong value in the actual UDP checksum field at
offset 6. (Even worse, the host network stack may then recompute the
UDP checksum, "correcting" it to match the corrupt data before sending
it out a physical interface.)
Correct this by tracking the TSO context independently of the non-TSO
context, and selecting the appropriate context based on the TSE flag
in each transmit data descriptor.
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
sum_needed and cptse flags are received from the guest within each
transmit data descriptor. They are not part of the offload context;
instead, they determine how to apply a previously received context to
the packet being transmitted:
- If cptse is set, perform both segmentation and checksum offload
using the parameters in the TSO context; otherwise just do checksum
offload. (Currently the e1000 device incorrectly stores only one
context, which will be fixed in a subsequent patch.)
- Depending on the bits set in sum_needed, possibly perform L4
checksum offload and/or IP checksum offload, using the parameters in
the appropriate context.
Move these flags out of struct e1000x_txd_props, which is otherwise
dedicated to storing values from a context descriptor, and into the
per-packet TX struct.
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Guest state should not be touched if VM is stopped, unfortunately we
didn't check running state and tried to drain tx queue unconditionally
in virtio_net_set_status(). A crash was then noticed as a migration
destination when user type quit after virtqueue state is loaded but
before region cache is initialized. In this case,
virtio_net_drop_tx_queue_data() tries to access the uninitialized
region cache.
Fix this by only dropping tx queue data when vm is running.
Fixes: 283e2c2adc ("net: virtio-net discards TX data after link down")
Cc: Yuri Benditovich <yuri.benditovich@daynix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Since commit ab06ec4357 we test the vmxnet3 device in the
pxe-tester, too (when running "make check SPEED=slow"). This now
revealed that the code is not working there if the host is a big
endian machine (for example ppc64 or s390x) - "make check SPEED=slow"
is now failing on such hosts.
The vmxnet3 code lacks endianness conversions in a couple of places.
Interestingly, the bitfields in the structs in vmxnet3.h already tried to
take care of the *bit* endianness of the C compilers - but the code missed
to change the *byte* endianness when reading or writing the corresponding
structs. So the bitfields are now wrapped into unions which allow to change
the byte endianness during runtime with the non-bitfield member of the union.
With these changes, "make check SPEED=slow" now properly works on big endian
hosts, too.
Reported-by: David Gibson <dgibson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: David Gibson <dgibson@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The checksum algorithm used by IPv4, TCP and UDP allows a zero value
to be represented by either 0x0000 and 0xFFFF. But per RFC 768, a zero
UDP checksum must be transmitted as 0xFFFF because 0x0000 is a special
value meaning no checksum.
Substitute 0xFFFF whenever a checksum is computed as zero when
modifying a UDP datagram header. Doing this on IPv4 and TCP checksums
is unnecessary but legal. Add a wrapper for net_checksum_finish() that
makes the substitution.
(We can't just change net_checksum_finish(), as that function is also
used by receivers to verify checksums, and in that case the expected
value is always 0x0000.)
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Since commit 1865e288a8 ("Fix eepro100 simple transmission
mode"), the test/pxe-test is broken for the eepro100 device on big
endian hosts. However, it seems like that commit did not introduce the
problem, but just uncovered it: The EEPRO100State->tx.tbd_array_addr and
EEPRO100State->tx.tcb_bytes fields are already in host byte order, since
they have already been byte-swapped in the read_cb() function.
Thus byte-swapping them in tx_command() again results in the wrong
endianness. Removing the byte-swapping here fixes the pxe-test.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This reverts commit 5e89dc0113 since:
- we should use ID in the spec instead the one used by OEM
- in the future, we should allow changing id through either property
or EEPROM file.
Cc: Stefan Weil <sw@weilnetz.de>
Cc: Michael Nawrocki <michael.nawrocki@gtri.gatech.edu>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Adds a new PCI ID for the i82559a (0x8086 0x1030) interface. The
"x-use-alt-device-id" property controls whether this new ID is to be
used, and is true by default, and set to false in a compat entry.
Signed-off-by: Mike Nawrocki <michael.nawrocki@gtri.gatech.edu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The simple transmission mode was treating the area immediately after the
transmit command block (TCB) as if it were a transmit buffer descriptor,
when in reality it is simply the packet data. This change simply copies
the data following the TCB into the packet buffer.
Signed-off-by: Mike Nawrocki <michael.nawrocki@gtri.gatech.edu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This enables them to be used outside of lance.c. We also update the comment to
refer to the SPARC32 lance device rather than the AMD PCNet-II device (of which
lance is a register-compatible subset).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Jason Wang <jasowang@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change all devices that set is_express=1 to implement
INTERFACE_PCIE_DEVICE.
Cc: Keith Busch <keith.busch@intel.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: qemu-block@nongnu.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following devices support both PCI Express and Conventional
PCI, by including special code to handle the QEMU_PCI_CAP_EXPRESS
flag and/or conditional pcie_endpoint_cap_init() calls:
* vfio-pci (is_express=1, but legacy PCI handled by
vfio_populate_device())
* vmxnet3 (is_express=0, but PCIe handled by vmxnet3_realize())
* pvscsi (is_express=0, but PCIe handled by pvscsi_realize())
* virtio-pci (is_express=0, but PCIe handled by
virtio_pci_dc_realize(), and additional legacy PCI code at
virtio_pci_realize())
* base-xhci (is_express=1, but pcie_endpoint_cap_init() call
is conditional on pci_bus_is_express(dev->bus)
* Note that xhci does not clear QEMU_PCI_CAP_EXPRESS like the
other hybrid devices
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Enable it by default for the sparc64-softmmu configuration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
This adds a simplistic emulation of the Sun GEM ethernet controller
found in Apple ASICs.
Currently we only support the Apple UniNorth 1.x variant, but the
other Apple or Sun variants should mostly be a matter of adding
PCI IDs options.
We have a very primitive emulation of a single Broadcom 5201 PHY
which is supported by the MacOS driver.
This model brings out-of-the-box networking to MacOS 9, and all
versions of OS X I tried with the mac99 platform.
Further improvements from Mark:
- Remove sungem.h file, moving constants into sungem.c as required
- Switch to using tracepoints for debugging
- Split register blocks into separate memory regions
- Use arrays in SunGEMState to hold register values
- Add state-saving support
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SunOS defines SEC in <sys/time.h> as 1 (commonly used time symbols).
This fixes build on SmartOS (Joyent).
Patch cherry-picked from pkgsrc by jperkin (Joyent).
Signed-off-by: Kamil Rytarowski <n54@gmx.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Both io and memory use the same mmio functions in the rtl8139 device.
This patch removes the separate MemoryRegionOps and old_mmio accessors
for memory, and replaces it with an alias to the io memory region.
Signed-off-by: Matt Parker <mtparkr@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Cc: jasowang@redhat.com
Cc: jiri@resnulli.us
Cc: armbru@redhat.com
Cc: f4bug@amsat.org
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The rocker device still implements the old PCIDeviceClass .init()
instead of the new .realize(). All devices need to be converted to
.realize().
.init() reports errors with fprintf() and return 0 on success, negative
number on failure. Meanwhile, when -device rocker fails, it first report
a specific error, then a generic one, like this:
$ x86_64-softmmu/qemu-system-x86_64 -device rocker,name=qemu-rocker
rocker: name too long; please shorten to at most 9 chars
qemu-system-x86_64: -device rocker,name=qemu-rocker: Device initialization failed
Now, convert it to .realize() that passes errors to its callers via its
errp argument. Also avoid the superfluous second error message. After
the patch, effect like this:
$ x86_64-softmmu/qemu-system-x86_64 -device rocker,name=qemu-rocker
qemu-system-x86_64: -device rocker,name=qemu-rocker: name too long; please shorten to at most 9 chars
Cc: jasowang@redhat.com
Cc: jiri@resnulli.us
Cc: armbru@redhat.com
Cc: f4bug@amsat.org
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
pci_rocker_init() leaks a World when the name more than 9 chars,
then return a negative value directly, doesn't make a correct
cleanup. So add a new goto label to fix it.
Cc: jasowang@redhat.com
Cc: jiri@resnulli.us
Cc: armbru@redhat.com
Cc: f4bug@amsat.org
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
