Provide *_init functions that populate an I2CAdapter struct without
allocating one, and make the existing *_create functions wrap them.
Because in the new setup *_create might return a pointer inside the
IMXI2C or OMAPI2C struct, create companion *_free functions to go
back to the outer pointer.
All this is temporary until allocation will be handled entirely by
qgraph.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no need to have a test device created by the board.
Instead, create it in the qtest so that we will be able to run
it on other boards too.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
receive_autoinc is relying on the LED state that is set by
send_and_receive. Stop doing that, because qgraph resets the
machine between tests.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If more than 4 bytes are received, the FIFO cannot host the entire
contents of the transfer and STP will be nonzero before entering
the transfer loop. Also, CNT will contain the number of bytes
left to be transferred instead of the total number of bytes in
the transfer.
(Reverse engineered from the omap_i2c.c source code; no available
datasheet).
This will fix ds1338-test for omap-i2c.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions to read/write 8-bit or 16-bit registers are the same
in tmp105 and pca9552 tests, and in fact they are a special case of
"read block"/"write block" functionality; read block in turn is used
in ds1338-test.
Move everything inside libqos-test, removing the duplication. Account
for the small differences by adding to tmp105-test.c the "read register
after writing" behavior that is specific to it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, if qos_node_contains was passed options, it would still
create an edge without any options. Instead, in that case
NULL acts as a terminator.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow choosing the bus that the device will be placed on, in case
the machine has more than one. Otherwise, the bus may not match
the base address of the controller we attach it to.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is a rare race between the atomic_cmpxchg and
bdrv_aio_cancel/bdrv_aio_cancel_async invocations. Detect it, the
only sensible we can do about it is to exit long_cb immediately.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add tests for MSA bit set instructions. This includes following
instructions:
* BCLR.B - clear bit (bytes)
* BCLR.H - clear bit (halfwords)
* BCLR.W - clear bit (words)
* BCLR.D - clear bit (doublewords)
* BNEG.B - negate bit (bytes)
* BNEG.H - negate bit (halfwords)
* BNEG.W - negate bit (words)
* BNEG.D - negate bit (doublewords)
* BSET.B - set bit (bytes)
* BSET.H - set bit (halfwords)
* BSET.W - set bit (words)
* BSET.D - set bit (doublewords)
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Message-Id: <1555699081-24577-5-git-send-email-aleksandar.markovic@rt-rk.com>
Add missing bits and peaces of the tests of the emulation of certain
MSA (non-immediate variants): some tests were missing two last cases;
some instructions were missing wrappers; some test included wrong
headers; some tests were missing altogether; updated some copywright
preambles; do several other minor cleanups.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Message-Id: <1555699081-24577-4-git-send-email-aleksandar.markovic@rt-rk.com>
Next pull request against qemu-4.1. Highlights:
* KVM accelerated support for the XIVE interrupt controller in PAPR
guests
* A number of TCG vector fixes
* Fixes for the PReP / 40p machine
* Improvements to make check-tcg test coverage
Other than that it's just a bunch of assorted fixes, cleanups and
minor improvements.
This supersedes both the pull request dated 2019-05-21 and the one
dated 2019-05-22. I've dropped one hunk which I think may have caused
the check-tcg failure that Peter saw (by enabling the ppc64abi32
build, which I think has been broken for ages). I'm not entirely
certain, since I haven't reproduced exactly the same failure.
-----BEGIN PGP SIGNATURE-----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=2q3B
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190529' into staging
ppc patch queue 2019-05-29
Next pull request against qemu-4.1. Highlights:
* KVM accelerated support for the XIVE interrupt controller in PAPR
guests
* A number of TCG vector fixes
* Fixes for the PReP / 40p machine
* Improvements to make check-tcg test coverage
Other than that it's just a bunch of assorted fixes, cleanups and
minor improvements.
This supersedes both the pull request dated 2019-05-21 and the one
dated 2019-05-22. I've dropped one hunk which I think may have caused
the check-tcg failure that Peter saw (by enabling the ppc64abi32
build, which I think has been broken for ages). I'm not entirely
certain, since I haven't reproduced exactly the same failure.
# gpg: Signature made Wed 29 May 2019 07:49:04 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190529: (44 commits)
ppc/pnv: add dummy XSCOM registers for PRD initialization
ppc/pnv: introduce new skiboot platform properties
spapr: Don't migrate the hpt_maxpagesize cap to older machine types
spapr: change default interrupt mode to 'dual'
spapr/xive: fix multiple resets when using the 'dual' interrupt mode
docs: provide documentation on the POWER9 XIVE interrupt controller
spapr/irq: add KVM support to the 'dual' machine
ppc/xics: fix irq priority in ics_set_irq_type()
spapr/irq: initialize the IRQ device only once
spapr/irq: introduce a spapr_irq_init_device() helper
spapr: check for the activation of the KVM IRQ device
spapr: introduce routines to delete the KVM IRQ device
sysbus: add a sysbus_mmio_unmap() helper
spapr/xive: activate KVM support
spapr/xive: add migration support for KVM
spapr/xive: introduce a VM state change handler
spapr/xive: add state synchronization with KVM
spapr/xive: add hcall support when under KVM
spapr/xive: add KVM support
spapr: Print out extra hints when CAS negotiation of interrupt mode fails
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Expected table change is then handled like this:
1. add table to diff allowed list
2. change generating code (can be combined with 1)
3. maintainer runs a script to update expected +
blows away allowed diff list
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We currently have docker cross building targets for powerpc (32-bit, BE)
and ppc64el (64-bit, LE), but not for pcp64 (64-bit, BE). This is an
irritating gap in make check-tcg coverage so correct it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This test shows that external snapshots and incremental backups are
friends.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190517152111.206494-3-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
We mandate that the source node must be a root node; but there's no reason
I am aware of that it needs to be restricted to such. In some cases, we need
to make sure that there's a medium present, but in the general case we can
allow the backup job itself to do the graph checking.
This patch helps improve the error message when you try to backup from
the same node more than once, which is reflected in the change to test
056.
For backups with bitmaps, it will also show a better error message that
the bitmap is in use instead of giving you something cryptic like "need
a root node."
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1707303
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20190521210053.8864-1-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
If COW areas of the newly allocated clusters are zeroes on the backing
image, efficient bdrv_write_zeroes(flags=BDRV_REQ_NO_FALLBACK) can be
used on the whole cluster instead of writing explicit zero buffers later
in perform_cow().
iotest 060:
write to the discarded cluster does not trigger COW anymore.
Use a backing image instead.
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Message-id: 20190516142749.81019-2-anton.nefedov@virtuozzo.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
bdrv_unref_child() does the following things:
- Updates the child->bs->inherits_from pointer.
- Calls bdrv_detach_child() to remove the BdrvChild from bs->children.
- Calls bdrv_unref() to unref the child BlockDriverState.
When bdrv_unref_child() was introduced in commit 33a604075c it was not
used in bdrv_close() because the drivers that had additional children
(like quorum or blkverify) had already called bdrv_unref() on their
children during their own close functions.
This was changed later (in 0bd6e91a7e for quorum, in 3e586be0b2 for
blkverify) so there's no reason not to use bdrv_unref_child() in
bdrv_close() anymore.
After this there's also no need to remove bs->backing and bs->file
separately from the rest of the children, so bdrv_close() can be
simplified.
Now bdrv_close() unrefs all children (before this patch it was only
bs->file and bs->backing). As a result, none of the callers of
brvd_attach_child() should remove their reference to child_bs (because
this function effectively steals that reference). This patch updates a
couple of tests that were doing their own bdrv_unref().
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 6d1d5feaa53aa1ab127adb73d605dc4503e3abd5.1557754872.git.berto@igalia.com
[mreitz: s/where/were/]
Signed-off-by: Max Reitz <mreitz@redhat.com>
reconnect for vhost blk
tests for UEFI
misc other stuff
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJc5AAMAAoJECgfDbjSjVRp57wIAKUAF8mvTaFfl/ge9IKJ0ZSO
+dZS+2Zdc52n3Qk2K511hMvMmWD6xO98+VSXzwax2KgfIVCcQyYSCSbkyqZ4XiFg
JUobhLHs6W24zn+2T8vZoqe4XWU6Pm1Y6NM72EFuhag8mhFlwWyMjpTwsISbjhGM
/FpHsPpB2/c7Uofe8CVmPl55PDqOoIm35YlbH5v6zUtBiPNRgZTDOMtYjl/tyuZC
VExs41/G15psNDIFd4dL1Zq6UjQBdu3ALIjIXTmPfg0nFXZn7FrOBRHbXWyzR9Tb
rqEDauxb3iGHphgNqeumfrSPXNrfB91Z8AD2aerTcvgUEdbc9QykxS/YM3erkGo=
=kkcS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: features, fixes
reconnect for vhost blk
tests for UEFI
misc other stuff
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 21 May 2019 14:41:32 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (34 commits)
tests: acpi: print error unable to dump ACPI table during rebuild
tests: acpi: refactor rebuild-expected-aml.sh to dump ACPI tables for a specified list of targets
tests: acpi: allow to override default accelerator
tests: acpi: ignore SMBIOS tests when UEFI firmware is used
tests: acpi: add a way to start tests with UEFI firmware
tests: acpi: add acpi_find_rsdp_address_uefi() helper
tests: acpi: move boot_sector_init() into x86 tests branch
tests: acpi: skip FACS table if board uses hw reduced ACPI profile
tests: acpi: fetch X_DSDT if pointer to DSDT is 0
tests: acpi: make pointer to RSDP 64bit
tests: acpi: make RSDT test routine handle XSDT
tests: acpi: make acpi_fetch_table() take size of fetched table pointer
tests: acpi: rename acpi_parse_rsdp_table() into acpi_fetch_rsdp_table()
pci: Simplify pci_bus_is_root()
pcie: Remove redundant test in pcie_mmcfg_data_{read,write}()
libvhost-user: fix bad vu_log_write
hw/arm/virt-acpi-build: pass AcpiMcfgInfo to build_mcfg()
i386, acpi: remove mcfg_ prefix in AcpiMcfgInfo members
hw/arm/virt-acpi-build: remove unnecessary variable mcfg_start
do not call vhost_net_cleanup() on running net from char user event
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- some iotests patches that have multiple reviews and thus are ready to go
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=P3eP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2019-05-21' into staging
- qtest patches to get rid of the global_qtest variable in more tests
- some iotests patches that have multiple reviews and thus are ready to go
# gpg: Signature made Tue 21 May 2019 11:40:31 BST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2019-05-21:
tests/qemu-iotests: Remove the "_supported_os Linux" line from many tests
cirrus / travis: Add gnu-sed and bash for macOS and FreeBSD
tests/qemu-iotests: Do not hard-code the path to bash
tests/qemu-iotests/check: Pick a default machine if necessary
tests/qemu-iotests/005: Add a sanity check for large sparse file support
tests/hd-geo-test: Use qtest_init() instead of qtest_start()
tests/device-introspect: Use qtest_init() instead of qtest_start()
tests/qom-test: Use qtest_init() instead of qtest_start()
tests/numa-test: Use qtest_init() instead of qtest_start()
tests/q35-test: Make test independent of global_qtest
tests/libqos: Get rid of global_qtest dependency in qvring_init()
tests/libqtest: Fix description of qtest_vinitf() and qtest_initf()
tests/libqtest: Remove unused global_qtest-related wrapper functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run.
Use qtest_init() and qtest_quit() instead.
Message-Id: <20190515174328.16361-7-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run.
Use qtest_init() and qtest_quit() instead.
Message-Id: <20190515174328.16361-6-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run.
Use qtest_init() and qtest_quit() instead.
Message-Id: <20190515174328.16361-5-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run.
Use qtest_init() and qtest_quit() instead.
Message-Id: <20190515174328.16361-4-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Use a local QTestState variable, so that we can finally get rid
of the undesired global_qtest variable in this file, too.
Message-Id: <20190515174328.16361-3-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Library functions should not depend on global_qtest functions like
writew() and writeq(), so that they can also be used in tests that
deal with multiple QTestStates at the same time (like migration tests).
Message-Id: <20190515174328.16361-2-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
A bunch of the wrapper functions that use global_qtest are not used
anymore. Remove them to avoid that they are used in new code again.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190510052239.21947-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
By default test cases were run with 'kvm:tcg' accelerators to speed up
tests execution. While it works for x86, were change of accelerator
doesn't affect ACPI tables, the approach doesn't works for ARM usecase
though.
In arm/virt case, KVM mode requires using 'host' cpu model, which
isn't available in TCG mode. That could be worked around with 'max'
cpu model, which works both for KVM and TCG. However in KVM mode it
is necessary to specify matching GIC version, which also could use
'max' value to automatically pick GIC version suitable for host's CPU.
Depending on host cpu type, different GIC versions would be used,
which in turn leads to different ACPI tables (APIC) generated.
As result while comparing with reference blobs, test would fail if
host's GIC version won't match the version on the host where
reference blobs where generated.
Let's keep testing simple for now and allow ARM tests run in TCG only
mode. To do so introduce 'accel' parameter in test configuration, so
test case could override default "kvm:tcg" with accelerator of choice.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1556808723-226478-12-git-send-email-imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For testcase to use UEFI firmware, one needs to provide and specify
firmware and varstore blob names in test_data { uefi_fl1, uefi_fl2 }
fields respectively and RAM start address plus size where to look for
test structure signature. Additionally testcase should specify
bootable cdrom image from uefi-boot-images with EFI test utility.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <1556808723-226478-10-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
introduce UEFI specific counterpart to acpi_find_rsdp_address()
that will help to find RSDP address when [OA]VMF is used as
firmware. It requires guest firmware or other guest app to place
1Mb aligned UefiTestSupport structure (defined in this patch)
in RAM with UefiTestSupport::signature_guid set to
AB87A6B1-2034-BDA0-71BD-375007757785
For test app details see commit
(09a274d82f tests: introduce "uefi-test-tools" with the BiosTablesTest UEFI app)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <1556808723-226478-9-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
that way it would be possible to test a DSDT pointed by
64bit X_DSDT field in FADT.
PS:
it will allow to enable testing arm/virt board, which sets
only newer X_DSDT field.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1556808723-226478-6-git-send-email-imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If RSDP revision is more than 0 fetch table pointed by XSDT
and fallback to legacy RSDT table otherwise.
While at it drop unused acpi_get_xsdt_address().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1556808723-226478-4-git-send-email-imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently acpi_fetch_table() assumes 32 bit size of table pointer
in ACPI tables. However X_foo variants are 64 bit, prepare
acpi_fetch_table() to handle both by adding an argument
for addr_ptr pointed entry size. Follow up commits will use that
to read XSDT and X_foo entries in ACPI tables.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1556808723-226478-3-git-send-email-imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Sometimes, 245 fails for me because some stream job has already finished
while the test expects it to still be active. (With -c none, it fails
basically every time.) The most reliable way to fix this is to simply
set auto_finalize=false so the job will remain in the block graph as
long as we need it. This allows us to drop the rate limiting, too,
which makes the test faster.
The only problem with this is that there is a single place that yields a
different error message depending on whether the stream job is still
copying data (so COR is enabled) or not (COR has been disabled, but the
job still has the WRITE_UNCHANGED permission on the target node). We
can easily address that by expecting either error message.
Note that we do not need auto_finalize=false (or rate limiting) for the
active commit job, because It never completes without an explicit
block-job-complete anyway.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
log() is in the current module, there is no need to prefix it. In fact,
doing so may make VM.run_job() unusable in tests that never use
iotests.log() themselves.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sometimes we cannot tell which error message qemu will emit, and we do
not care. With this change, we can then just pass an array of all
possible messages to assert_qmp() and it will choose the right one.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already have 221 for accesses through the page cache, but it is
better to create a new file for O_DIRECT instead of integrating those
test cases into 221. This way, we can make use of
_supported_cache_modes (and _default_cache_mode) so the test is
automatically skipped on filesystems that do not support O_DIRECT.
As part of the split, add _supported_cache_modes to 221. With that, it
no longer fails when run with -c none or -c directsync.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qmp_cont fails if vm in RUN_STATE_FINISH_MIGRATE, so let's wait for
final RUN_STATE_POSTMIGRATE. Also, while being here, check qmp_cont
result.
Reported-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Tested-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some objects are only needed for system emulation and tools.
We can ignore them for the user mode case
Update tests to run accordingly: conditionally build some tests
on CONFIG_BLOCK.
Some tests use components that are only built when softmmu or
block tools are enabled, not for linux-user. So, if these components
are not available, disable the tests.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190401141222.30034-6-lvivier@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
When possible use generated-files-$(FLAG) to disable
some targets (like KEYCODEMAP_FILES).
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20190401141222.30034-3-lvivier@redhat.com>
The Exclusive Instructions provide a general-purpose mechanism for
atomic updates of memory-based synchronization variables that can be
used for exclusion algorithms.
Use cmpxchg-based implementation that is sufficient for the typical use
of exclusive access in atomic operations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Cleaned up with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-9-armbru@redhat.com>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-6-armbru@redhat.com>
[Rebase to master: update include/hw/net/ne2000-isa.h]
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
slirp/src/*
target/s390x/gen-features.c
tests/fp/platform.h
tests/migration/s390x/a-b-bios.c
tests/test-rcu-simpleq.c
tests/test-rcu-tailq.c
tests/uefi-test-tools/UefiTestToolsPkg/BiosTablesTest/BiosTablesTest.c
We're in the process of spinning out slirp/. tests/fp/platform.h is
has to include qemu/osdep.h because tests/fp/berkeley-softfloat-3/ and
tests/fp/berkeley-testfloat-3/ don't. tests/uefi-test-tools/ is guest
software. The remaining reverts are the same as in commit
b7d89466dd.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190313162812.8885-1-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[Revert change to tests/fp/platform.h, adjust commit message]
This patch adds a test for rebasing an image that currently does not
have a backing file.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This tests that a job coroutine always runs in the right iothread after
the AioContext of its main node has changed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Test case 192 calls _launch_qemu, so it also needs to _cleanup_qemu when
it's done, otherwise the QMP FIFOs stay around in scratch/. It also
creates a temporary NBD socket that needs to be removed as well at the
end of the test case.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
- Get rid of some more dependencies on the global_qtest variable in the qtests
- Some other small test clean-ups
- Some copyright statement clarifications
- Mark TARGET_FMT_lu as poisoned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=LGlY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2019-05-09' into staging
- Fix "make check" problem that occurred with LANG=C and Python 3.5 / 3.6
- Get rid of some more dependencies on the global_qtest variable in the qtests
- Some other small test clean-ups
- Some copyright statement clarifications
- Mark TARGET_FMT_lu as poisoned
# gpg: Signature made Thu 09 May 2019 08:45:47 BST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2019-05-09:
include/exec/poison: Mark TARGET_FMT_lu as poisoned, too
target/sh4: Fix LGPL information in the file headers
target/openrisc: Fix LGPL information in the file headers
hw/i2c/smbus_ich9: Fix the confusing contributions-after-2012 statement
tests: qpci_unplug_acpi_device_test() should not rely on global_qtest
tests/drive_del-test: Use qtest_init() instead of qtest_start()
tests/Makefile: Remove unused test-obj-y variable
tests/tpm-tests: Use g_test_skip() to mark skipped tests
tests/ide-test: Make test independent of global_qtest
tests/test-hmp: Use qtest_init() instead of qtest_start()
tests/qmp-cmd-test: Use qtest_init() instead of qtest_start()
tests/megasas: Make test independent of global_qtest
tests/tco: Make test independent of global_qtest
tests: Force Python I/O encoding for check-qapi-schema
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
libqos functions should not use functions that require global_qtest to
be set, since such library functions could also be used by tests that
deal with multiple test states. Add a parameter to this function to
explicitly specify the test state.
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190508143209.24350-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run
Use qtest_init() and qtest_quit() instead.
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190508142153.21555-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
I recently noticed that test-obj-y contains a file called
tests/check-block-qtest.o which simply does not belong to any .c
file and thus wondered why this is not causing any trouble. It is
only used to add -Itests to the command line (which refers to the
build directory). However, it is not needed because "-iquote $(@D)"
already sets this up in rules.mak. Thus we can simply remove this
variable.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190508075527.32164-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Pass around the QTestState, so we do not need the problematic global_qtest
variable (which causes trouble for tests that have multiple test states)
here anymore.
Message-Id: <20190409085245.31548-6-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run
Use qtest_init() and qtest_quit() instead.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190409085245.31548-5-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run
(since global_qtest can not be used in tests that have to track
multiple QEMU states, like migration tests). Use qtest_init() and
qtest_quit() instead.
Message-Id: <20190409085245.31548-4-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The test uses memwrite() and thus relies on global_qtest. Let's replace it
with qtest_memwrite(), so that we are independent from global_qtest here.
Message-Id: <20190409085245.31548-3-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Pass around the QTestState in the TestData, so we do not need the
global_qtest variable here anymore.
Message-Id: <20190409085245.31548-2-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
A recent patch results in qemu-img reporting the backing file format of
vmdk images as vmdk. This broke iotests 110 and 126.
Fixes: 7502be838e
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190415154129.31021-1-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This requires some changes to keep iotests 104 and 207 working.
qemu-img info in 104 will now return a filename including the user name
and the port, which need to be filtered by adjusting REMOTE_TEST_DIR in
common.rc. This additional information has to be marked optional,
however (which is simple as REMOTE_TEST_DIR is a regex), because
otherwise 197 and 215 would fail: They use it (indirectly) to filter
qemu-img create output which contains a backing filename they have
passed to it -- which probably does not contain a user name or port
number.
The problem in 207 is a nice one to have: qemu-img info used to return
json:{} filenames, but with this patch it returns nice plain ones. We
now need to adjust the filtering to hide the user name (and port number
while we are at it). The simplest way to do this is to include both in
iotests.remote_filename() so that bdrv_refresh_filename() will not
change it, and then iotests.img_info_log() will filter it correctly
automatically.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Message-id: 20190225190828.17726-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_inc_refcounts_imrt() (through realloc_refcount_array()) can eat
an unpredictable amount of memory on corrupted table entries, which are
referencing regions far beyond the end of file.
Prevent this, by skipping such regions from further processing.
Interesting that iotest 138 checks exactly the behavior which we fix
here. So, change the test appropriately.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190227131433.197063-3-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
182 fails if qemu has no support for hotplugging of a virtio-blk device.
Using an NBD server instead works just as well for the test, even on
qemus without hotplugging support.
Fixes: 6d0a4a0fb5
Reported-by: Danilo C. L. de Paula <ddepaula@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20190417153005.30096-1-mreitz@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
For some particular configurations of ext4, sizing an image to 84
sectors + 1 byte causes test failures when the size of the hole is
rounded to a 4k alignment. Let's instead size things to 128 sectors +
1 byte, as the 64k boundary is more likely to work with various hole
granularities.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190506172111.31594-1-eblake@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
The output of qemu-io changed recently - most tests have been fixed in
commit 36b9986b08 ("tests/qemu-iotests: Fix output of qemu-io
related tests") already, but a qcow1, vmdk, and nbd test were still missing.
Fixes: 99e98d7c9f ("qemu-io: Use error_[gs]et_progname()")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190501134127.21104-1-thuth@redhat.com>
[eblake: squash in NBD 083 fixes]
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Tested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
233 generally filters the port, but in two cases does not. If some
other concurrently running application has already taken port 10809,
this will result in an output mismatch. Fix this by applying the
filter in these two cases, too.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20190506160529.6955-1-mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Rebuild the "bios-tables-test" UEFI boot images with the SMBIOS entry
point reporting that has been added in the previous patch.
Cc: "Philippe Mathieu-Daudé" <philmd@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Launchpad: https://bugs.launchpad.net/qemu/+bug/1821884
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
On UEFI systems, the SMBIOS entry point (a.k.a. anchor) structures are
found similarly to the ACPI RSD PTR table(s): by scanning the
ConfigurationTable array in the EFI system table for well-known GUIDs.
Locate the SMBIOS 2.1 (32-bit) and 3.0 (64-bit) anchors in the
BiosTablesTest UEFI application, and report the addresses in new fields
appended to the BIOS_TABLES_TEST structure.
Cc: "Philippe Mathieu-Daudé" <philmd@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Launchpad: https://bugs.launchpad.net/qemu/+bug/1821884
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Just like the previous tests, boots a Linux kernel on a s390x target
using the s390-ccw-virtio machine.
Because it's not possible to have multiple VT220 consoles,
'-nodefaults' is used, so that the one set with set_console() works
correctly.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Message-Id: <20190312171824.5134-20-crosa@redhat.com>
[ehabkost: Updated kernel URL to point to fedoraproject.org]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Just like the previous tests, boots a Linux kernel on an arm target
using the virt machine.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Message-Id: <20190312171824.5134-19-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Just like the previous tests, boots a Linux kernel on a aarch64 target
using the virt machine.
One special option added is the CPU type, given that the kernel
selected fails to boot on the virt machine's default CPU (cortex-a15).
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Message-Id: <20190312171824.5134-18-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
A test can, optionally, be tagged for one or many architectures. If a
test has been tagged for a single architecture, there's a high chance
that the test won't run on other architectures. This changes the
default order of choosing a default target architecture to use based
on the 'arch' tag value first.
The precedence order is for choosing a QEMU binary to use for a test
is now:
* qemu_bin parameter
* arch parameter
* arch tag value (for example, x86_64 if "🥑 tags=arch:x86_64
is used)
This means that if one runs:
$ avocado run -p qemu_bin=/usr/bin/qemu-system-x86_64 test.py
No arch parameter or tag will influence the selection of the QEMU
target binary. If one runs:
$ avocado run -p arch=ppc64 test.py
The target binary selection mechanism will attempt to find a binary
such as "ppc64-softmmu/qemu-system-ppc64". And finally, if one runs
a test that is tagged (in its docstring) with "arch:aarch64":
$ avocado run aarch64.py
The target binary selection mechanism will attempt to find a binary
such as "aarch64-softmmu/qemu-system-aarch64".
At this time, no provision is made to cancel the execution of tests if
the arch parameter given (manually) does not match the test "arch"
tag, but it may be a useful default behavior to be added in the
future.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-7-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently, some tests contains target architecture information, in the
form of a "x86_64" tag. But that tag is not respected in the default
execution, that is, "make check-acceptance" doesn't do anything with
it.
That said, even the target architecture handling currently present in
the "avocado_qemu.Test" class is pretty limited. For instance, by
default, it chooses a target based on the host architecture.
Because the original implementation of the tags feature in Avocado did
not include any time of namespace or "key:val" mechanism, no tag has
relation to another tag. The new implementation of the tags feature
from version 67.0 onwards, allows "key:val" tags, and because of that,
a test can be classified with a tag in a given key. For instance, the
new proposed version of the "boot_linux_console.py" test, which
downloads and attempts to run a x86_64 kernel, is now tagged as:
🥑 tags=arch:x86_64
This means that it can be filtered (out) when no x86_64 target is
available. At the same time, tests that don't have a "arch:" tag,
will not be filtered out.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-6-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add a gva2gpa command purely for debug which performs
address translation on the gva, the existing gpa2hva
command can then also be used to find it in the qemu
userspace; e.g.
(qemu) info registers
.... RSP=ffffffff81c03e98
....
(qemu) gva2gpa 0xffffffff81c03e98
gpa: 0x1c03e98
(qemu) gpa2hva 0x1c03e98
Host virtual address for 0x1c03e98 (pc.ram) is 0x7f0599a03e98
(qemu) x/10x 0xffffffff81c03e98
ffffffff81c03e98: 0x81c03eb8 0xffffffff 0x8101ea3f 0xffffffff
ffffffff81c03ea8: 0x81d27b00 0xffffffff 0x00000000 0x00000000
ffffffff81c03eb8: 0x81c03ec8 0xffffffff
gdb -p ...qemu...
(gdb) x/10x 0x7f0599a03e98
0x7f0599a03e98: 0x81c03eb8 0xffffffff 0x8101ea3f 0xffffffff
0x7f0599a03ea8: 0x81d27b00 0xffffffff 0x00000000 0x00000000
0x7f0599a03eb8: 0x81c03ec8 0xffffffff
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190412152652.827-1-dgilbert@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
qemu-img create allows giving just a format and "-o help" to get a list
of the options supported by that format. Users may not realize that the
protocol level may offer even more options, which they only get to see
by specifying a filename.
This patch adds a note to hint at that fact.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In the "amend" section of 082, we perform a single "convert" test
(namely "convert -o help"). That does not make sense, especially
because we have done exactly that "convert" test earlier in 082 already.
Replacing "convert" by "amend" yields an error, which is correct because
there is no point in "amend" having a default format. The user has to
either specify the format, or give a file for qemu-img to probe.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Disk sizes close to INT64_MAX cause overflow, for some pretty
ridiculous output:
$ ./nbdkit -U - memory size=$((2**63 - 512)) --run 'qemu-img info $nbd'
image: nbd+unix://?socket=/tmp/nbdkitHSAzNz/socket
file format: raw
virtual size: -8388607T (9223372036854775296 bytes)
disk size: unavailable
But there's no reason to have two separate implementations of integer
to human-readable abbreviation, where one has overflow and stops at
'T', while the other avoids overflow and goes all the way to 'E'. With
this patch, the output now claims 8EiB instead of -8388607T, which
really is the correct rounding of largest file size supported by qemu
(we could go 511 bytes larger if we used byte-accurate sizing instead
of rounding up to the next sector boundary, but that wouldn't change
the human-readable result).
Quite a few iotests need updates to expected output to match.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Max Reitz <mreitz@redhat.com>
One of the recent commits changed the way qemu-io prints out its
errors and warnings - they are now prefixed with the program name.
We've got to adapt the iotests accordingly to prevent that they
are failing.
Fixes: 99e98d7c9f ("qemu-io: Use error_[gs]et_progname()")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tJvv
-----END PGP SIGNATURE-----
Merge tag 's390-ccw-bios-2019-04-12' into s390-next-staging
Support for booting from a vfio-ccw passthrough dasd device
# gpg: Signature made Fri 12 Apr 2019 01:17:03 PM CEST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
* tag 's390-ccw-bios-2019-04-12':
pc-bios/s390: Update firmware images
s390-bios: Use control unit type to find bootable devices
s390-bios: Support booting from real dasd device
s390-bios: Add channel command codes/structs needed for dasd-ipl
s390-bios: Use control unit type to determine boot method
s390-bios: Refactor virtio to run channel programs via cio
s390-bios: Factor finding boot device out of virtio code path
s390-bios: Extend find_dev() for non-virtio devices
s390-bios: cio error handling
s390-bios: Support for running format-0/1 channel programs
s390-bios: ptr2u32 and u32toptr
s390-bios: Map low core memory
s390-bios: Decouple channel i/o logic from virtio
s390-bios: Clean up cio.h
s390-bios: decouple common boot logic from virtio
s390-bios: decouple cio setup from virtio
s390 vfio-ccw: Add bootindex property and IPLB data
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
build and capture platform firmware binaries from that release. The
binaries are meant to be used by both end-users and by the "BIOS tables"
unit tests in qtest ("make check").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=k5c2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lersek/tags/edk2-pull-2019-04-22' into staging
Advance the roms/edk2 submodule to the "edk2-stable201903" release, and
build and capture platform firmware binaries from that release. The
binaries are meant to be used by both end-users and by the "BIOS tables"
unit tests in qtest ("make check").
# gpg: Signature made Mon 22 Apr 2019 19:20:08 BST
# gpg: using RSA key D39DA71E0D496CFA
# gpg: Good signature from "Laszlo Ersek <lersek@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: F5D9 660F 1BA5 F310 A95A C5E0 466A EAE0 6125 3988
# Subkey fingerprint: B3A5 5D3F 88A8 90ED 2E63 3E8D D39D A71E 0D49 6CFA
* remotes/lersek/tags/edk2-pull-2019-04-22:
MAINTAINERS: add the "EDK2 Firmware" subsystem
Makefile: install the edk2 firmware images and their descriptors
tests: add missing dependency to build QTEST_QEMU_BINARY, round 2
pc-bios: document the edk2 firmware images; add firmware descriptors
pc-bios: add edk2 firmware binaries and variable store templates
roms: build edk2 firmware binaries and variable store templates
roms/Makefile: replace the $(EDK2_EFIROM) target with "edk2-basetools"
roms/edk2-funcs.sh: add the qemu_edk2_get_thread_count() function
roms/edk2: advance to tag edk2-stable201903
tests/uefi-test-tools/build.sh: work around TianoCore#1607
roms/edk2-funcs.sh: require gcc-4.8+ for building i386 and x86_64
roms: lift "edk2-funcs.sh" from "tests/uefi-test-tools/build.sh"
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit b94b330e23 ("tests: add missing dependency to build
QTEST_QEMU_BINARY", 2017-07-31), Phil fixed the dependency list of make
target "check-qtest-%". Namely, the recipe would set QTEST_QEMU_BINARY to
the softmmu emulator for the emulation target, but the prerequisites
didn't include the emulator.
The same issue affects the "check-report-qtest-%.tap" make target, which
is the other make target whose recipe sets QTEST_QEMU_BINARY:
> $ make -j4 check-report-qtest-aarch64.tap
> TAP check-report-qtest-aarch64.tap
> sh: /.../aarch64-softmmu/qemu-system-aarch64: No such file or directory
Apply Phil's fix to this make target too.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The edk2-stabe201903 release introduced Python3 support to edk2's
BaseTools; however the Python3 enablement breaks in a corner case (which
is nevertheless supported by the edk2 community), namely the in-module
parallelization that we utilize.
This is tracked under
<https://bugzilla.tianocore.org/show_bug.cgi?id=1607>. For now, work
around the issue (in advance) by forcing Python2. (The workaround is a
no-op before we move to edk2-stabe201903 in the roms/edk2 submodule.)
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Extract the dense logic for architecture and toolchain massaging from
"tests/uefi-test-tools/build.sh", to a set of small functions. We'll reuse
these functions for building full platform firmware images.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Filter the qemu-nbd server output to get rid of a direct reference
to my build directory.
Fixes: e9dce9cb
Reported-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
tmpfs does not support O_DIRECT. Detect this case, and skip flipping
@direct if the filesystem does not support it.
Fixes: bf3e50f623
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make a new routine find_boot_device to locate the boot device for all
cases, not just virtio.
The error message for the case where no boot device has been specified
and a suitable boot device cannot be auto detected was specific to
virtio devices. We update this message to remove virtio specific wording.
Signed-off-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <1554388475-18329-12-git-send-email-jjherne@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
drive_new() returns null without setting an error when it provided
help. add_init_drive() assumes null means failure, and crashes trying
to report a null error.
Fixes: c4f26c9f37
Cc: qemu-stable@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The test uses the trick:
if (!opts) {
opts = &(QOSGraph...Options) { };
}
in a couple of places, however the temporary created
by the &() {} goes out of scope at the bottom of the if,
and results in a seg or assert when opts-> fields are
used (on fedora 30's gcc 9).
Fixes: fc281c8020
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190405184037.16799-1-dgilbert@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Clean up wrong usage of FALSE and TRUE in places that use "bool" from stdbool.h.
FALSE and TRUE (with capital letters) are the constants defined by glib for
being used with the "gboolean" type of glib. But some parts of the code also use
TRUE and FALSE for variables that are declared as "bool" (the type from <stdbool.h>).
Signed-off-by: Jafar Abdi <cafer.abdi@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <1553351197-14581-4-git-send-email-cafer.abdi@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Clean up wrong usage of FALSE and TRUE in places that use "bool" from stdbool.h.
FALSE and TRUE (with capital letters) are the constants defined by glib for
being used with the "gboolean" type of glib. But some parts of the code also use
TRUE and FALSE for variables that are declared as "bool" (the type from <stdbool.h>).
Signed-off-by: Jafar Abdi <cafer.abdi@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1553351197-14581-3-git-send-email-cafer.abdi@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Ensure watch IDs unique within a monitor and avoid integer wraparound
issues when many watches are set & unset over time.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJco1tUAAoJEL6G67QVEE/f9xYP/2OTsAk6dHCcWqc///jXN0JW
OLcnpmjuh5KgUmOrs7NIRYRo2DARrhNDDXckHjDuX2HmnzoTB5p7DXLWMPgAzxj6
o83yxYT0Qqw79wxqbDmJ1y3kUVka1r94wCmmvUmxQZjLbDk8u2ytNUDbEOVlM0VJ
R7T800j8PhbY1pg9PiJJZonm7dxZAVNSCF4AgkrJVIes6MqhvNUhVsck5q/CC3yi
0jkglsiVTyXjKpJsioM9VhQXeqiHfFl3qjcPi0XQ99lVpTMFysNd4UdnVXhNs9NI
Xe52yQ7NG3fEggUivtFBmvVplNOg09K6U2vkyk9z8S1WTLZsbabwvwSvkVPW3Ty0
QaDgI6wNSiBb7Lfl2bbUR6X3j9QXUn8bhlczBsorS4uU4+NdHGyERsZLKLZazYYz
5t+xm4YBGJhtlt8IglNBjtaJFBuqgjrBEuBkfpevB2ocioWnU6APOdwWkKlSe3+r
EuKFUcbhRiRAGO05DjntNkePigb66IVkSiJXd4uSid/+akn5kQ19PSD8tXdfvZ7h
8HYTnWZa3OSLd7tZlwRzimnKuVSIsSnj+NobkIs8HSS3N7oN1t4FC5jH9D6GmK0R
djQs6a5mHQbonrc0dXxlb+P8u6I+ppxznPpfL/aQJ4pFM18V6gmcZEQluhwALNe9
rdPUnCudC/9SUNpMf3rI
=qriK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/berrange/tags/filemon-next-pull-request' into staging
filemon: various fixes / improvements to file monitor for USB MTP
Ensure watch IDs unique within a monitor and avoid integer wraparound
issues when many watches are set & unset over time.
# gpg: Signature made Tue 02 Apr 2019 13:53:40 BST
# gpg: using RSA key BE86EBB415104FDF
# gpg: Good signature from "Daniel P. Berrange <dan@berrange.com>" [full]
# gpg: aka "Daniel P. Berrange <berrange@redhat.com>" [full]
# Primary key fingerprint: DAF3 A6FD B26B 6291 2D0E 8E3F BE86 EBB4 1510 4FDF
* remotes/berrange/tags/filemon-next-pull-request:
filemon: fix watch IDs to avoid potential wraparound issues
filemon: ensure watch IDs are unique to QFileMonitor scope
tests: refactor file monitor test to make it more understandable
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
