QEMU may crash when running a spapr machine in 'dual' interrupt controller
mode on some older (but not that old, eg. ubuntu 18.04.2) KVMs with partial
XIVE support:
qemu-system-ppc64: hw/ppc/spapr_rtas.c:411: spapr_rtas_register:
Assertion `!name || !rtas_table[token].name' failed.
XICS is controlled by the guest thanks to a set of RTAS calls. Depending
on whether KVM XICS is used or not, the RTAS calls are handled by KVM or
QEMU. In both cases, QEMU needs to expose the RTAS calls to the guest
through the "rtas" node of the device tree.
The spapr_rtas_register() helper takes care of all of that: it adds the
RTAS call token to the "rtas" node and registers a QEMU callback to be
invoked when the guest issues the RTAS call. In the KVM XICS case, QEMU
registers a dummy callback that just prints an error since it isn't
supposed to be invoked, ever.
Historically, the XICS controller was setup during machine init and
released during final teardown. This changed when the 'dual' interrupt
controller mode was added to the spapr machine: in this case we need
to tear the XICS down and set it up again during machine reset. The
crash happens because we indeed have an incompatibility with older
KVMs that forces QEMU to fallback on emulated XICS, which tries to
re-registers the same RTAS calls.
This could be fixed by adding proper rollback that would unregister
RTAS calls on error. But since the emulated RTAS calls in QEMU can
now detect when they are mistakenly called while KVM XICS is in
use, it seems simpler to register them once and for all at machine
init. This fixes the crash and allows to remove some now useless
lines of code.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156044429963.125694.13710679451927268758.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add a check to make sure that the routine initializing the emulated
IRQ device is called once. We don't have much to test on the XICS
side, so we introduce a 'init' boolean under ICSState.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries machine only uses LSIs to support legacy PCI devices. Every
PHB claims 4 LSIs at realize time. When using in-kernel XICS (or upcoming
in-kernel XIVE), QEMU synchronizes the state of all irqs, including these
LSIs, later on at machine reset.
In order to support PHB hotplug, we need a way to tell KVM about the LSIs
that doesn't require a machine reset. An easy way to do that is to always
inform KVM when an interrupt is claimed, which really isn't a performance
path.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059668360.1466090.5969630516627776426.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICS class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023084177.1011724.14693955932559990358.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We want to use the "simple" ICS type in both KVM and non-KVM setups.
Teach the "simple" ICS how to present interrupts to KVM and adapt
sPAPR accordingly.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023082996.1011724.16237920586343905010.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICSStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081817.1011724.14078777320394028836.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081228.1011724.12474992370439652538.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The realization of KVM ICP currently follows the parent_realize logic,
which is a bit overkill here. Also we want to get rid of the KVM ICP
class. Explicitely call icp_kvm_realize() from the base ICP realize
function.
Note that ICPStateClass::parent_realize is retained because powernv
needs it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080049.1011724.15423463482790260696.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP reset handler simply writes the ICP state to KVM. This
doesn't need the overkill parent_reset logic we have today. Call
icp_set_kvm_state() from the base ICP reset function instead.
Since there are no other users for ICPStateClass::parent_reset, and
it isn't currently expected to change, drop it as well.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023079461.1011724.12644984391500635645.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICPStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023078871.1011724.3083923389814185598.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When compiling with Clang in -std=gnu99 mode, there is a warning/error:
CC ppc64-softmmu/hw/intc/xics_spapr.o
In file included from /home/thuth/devel/qemu/hw/intc/xics_spapr.c:34:
/home/thuth/devel/qemu/include/hw/ppc/xics.h:203:34: error: redefinition of typedef 'sPAPRMachineState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
typedef struct sPAPRMachineState sPAPRMachineState;
^
/home/thuth/devel/qemu/include/hw/ppc/spapr_irq.h:25:34: note: previous definition is here
typedef struct sPAPRMachineState sPAPRMachineState;
^
We have to remove the duplicated typedef here and include "spapr.h" instead.
But "spapr.h" should not be included for the pnv machine files. So move
the spapr-related prototypes into a new file called "xics_spapr.h" instead.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
commit 15ed653fa4 ("ppc/xics: An ICS with offset 0 is assumed to be
uninitialized") introduced an extra check on the ICS offset which is
not strictly necessary.
Revert the change to be able to map the XICS IRQ number space on the
XIVE IRQ number space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu_irq array is now allocated at the machine level using a sPAPR
IRQ set_irq handler depending on the chosen interrupt mode. The use of
this handler is slightly inefficient today but it will become necessary
when the 'dual' interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To support the 'dual' interrupt mode, XICS and XIVE, we plan to move
the qemu_irq array of each interrupt controller under the machine and
do the allocation under the sPAPR IRQ init method.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE interface for the guest is described in the device tree under
the "interrupt-controller" node. A couple of new properties are
specific to XIVE :
- "reg"
contains the base address and size of the thread interrupt
managnement areas (TIMA), for the User level and for the Guest OS
level. Only the Guest OS level is taken into account today.
- "ibm,xive-eq-sizes"
the size of the event queues. One cell per size supported, contains
log2 of size, in ascending order.
- "ibm,xive-lisn-ranges"
the IRQ interrupt number ranges assigned to the guest for the IPIs.
and also under the root node :
- "ibm,plat-res-int-priorities"
contains a list of priorities that the hypervisor has reserved for
its own use. OPAL uses the priority 7 queue to automatically
escalate interrupts for all other queues (DD2.X POWER9). So only
priorities [0..6] are allowed for the guest.
Extend the sPAPR IRQ backend with a new handler to populate the DT
with the appropriate "interrupt-controller" node.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The number of MSI interrupts a sPAPR machine can allocate is in direct
relation with the number of interrupts of the sPAPRIrq backend. Define
statically this value at the sPAPRIrq class level and use it for the
"ibm,pe-total-#msi" property of the sPAPR PHB.
According to the PAPR specs, "ibm,pe-total-#msi" defines the maximum
number of MSIs that are available to the PE. We choose to advertise
the maximum number of MSIs that are available to the machine for
simplicity of the model and to avoid segmenting the MSI interrupt pool
which can be easily shared. If the pool limit is reached, it can be
extended dynamically.
Finally, remove XICS_IRQS_SPAPR which is now unused.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last user of the PowerPCCPU typedef in "hw/ppc/xics.h" vanished with
commit b1fd36c363. It isn't necessary to
include "target/ppc/cpu-qom.h" there anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Just like for the realize handlers, this makes possible to move the
common ICSState code of the reset handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes possible to move the common ICSState code of the realize
handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This changes the ICP realize and reset handlers in DeviceRealize and
DeviceReset handlers. parent handlers are now called from the
inheriting classes which is a cleaner object pattern.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
xics_get_qirq() is only used by the sPAPR machine. Let's move it there
and change its name to reflect its scope. It will be useful for XIVE
support which will use its own set of qirqs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also change the prototype to use a sPAPRMachineState and prefix them
with spapr_irq_. It will let us synchronise the IRQ allocation with
the XIVE interrupt mode when available.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sPAPR and the PowerNV core objects create the interrupt presenter
object of the CPUs in a very similar way. Let's provide a common
routine in which we use the presenter 'type' as a child identifier.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using the emulated XICS, the 'info pic' monitor command shows:
CPU 0 XIRR=ff000000 ((nil)) PP=ff MFRR=ff
ICS 1000..13ff 0x10040060340
1000 MSI 05 00
1001 MSI 05 00
1002 MSI 05 00
1003 MSI ff 00
1004 LSI ff 00
1005 LSI ff 00
1006 LSI ff 00
1007 LSI ff 00
1008 MSI 05 00
1009 MSI 05 00
100a MSI 05 00
100b MSI 05 00
100c MSI 05 00
but when using the in-kernel XICS with the very same guest, we get:
CPU 0 XIRR=00000000 ((nil)) PP=ff MFRR=ff
ICS 1000..13ff 0x10032e00340
1000 MSI ff 00
1001 MSI ff 00
1002 MSI ff 00
1003 MSI ff 00
1004 LSI ff 00
1005 LSI ff 00
1006 LSI ff 00
1007 LSI ff 00
1008 MSI ff 00
1009 MSI ff 00
100a MSI ff 00
100b MSI ff 00
100c MSI ff 00
ie, all irqs are masked and XIRR is null, while we should get the
same output as with the emulated XICS.
If the guest is then migrated, 'info pic' shows the expected values
on both source and destination.
The problem is that QEMU doesn't synchronize with KVM before printing
the XICS state. Migration happens to fix the output because it enforces
synchronization with KVM.
To fix the invalid output of 'info pic', this patch introduces a new
synchronize_state operation for both ICPStateClass and ICSStateClass.
The ICP operation relies on run_on_cpu() in order to kick the vCPU
and avoid sleeping on KVM_GET_ONE_REG.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cpu_setup() handler is only implemented by xics_kvm, where it really
does a typical "realize" job. Moreover, the realize() handler is called
shortly after cpu_setup(), on the same path.
This patch converts xics_kvm to implement realize() instead of cpu_setup().
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Until recently, spapr used to allocate ICPState objects for the lifetime
of the machine. They would only be associated to vCPUs in xics_cpu_setup()
when plugging a CPU core.
Now that ICPState objects have the same lifecycle as vCPUs, it is
possible to associate them during realization.
This patch hence open-codes xics_cpu_setup() in icp_realize(). The vCPU
is passed as a property. Note that vCPU now needs to be realized first
for the IRQs to be allocated. It also needs to resetted before ICPState
realization in order to synchronize with KVM.
Since ICPState objects are freed when unrealized, xics_cpu_destroy() isn't
needed anymore and can be safely dropped.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It makes more sense to pass an IPCState * to handlers of ICPStateClass
instead of a DeviceState *, if only to benefit from compile time type
checking. The same goes with ICSStateClass.
While here, we also change the declaration of ICPStateClass in xics.h
for consistency.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These properties are part of the XICS API. They deserve to appear
explicitely in the XICS header file.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Taking into account that qemu_set_irq() returns immediatly if its first
argument is NULL, icp_kvm_reset() largely duplicates icp_reset().
This patch introduces a reset() handler, so that the common logic can
be implemented in icp_reset() only.
While there we can also drop icp_kvm_realize() and icp_kvm_unrealize(). This
causes icp-kvm to be realized in icp_realize(), which sets icp->xics, but
it has no impact.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since commit a45863bda9 ("xics_kvm: Don't enable KVM_CAP_IRQ_XICS if
already enabled"), we were able to re-hotplug a vCPU that had been hot-
unplugged ealier, thanks to a boolean flag in ICPState that we set when
enabling KVM_CAP_IRQ_XICS.
This could work because the lifecycle of all ICPState objects was the
same as the machine. Commit 5bc8d26de2 ("spapr: allocate the ICPState
object from under sPAPRCPUCore") broke this assumption and now we always
pass a freshly allocated ICPState object (ie, with the flag unset) to
icp_kvm_cpu_setup().
This cause re-hotplug to fail with:
Unable to connect CPU8 to kernel XICS: Device or resource busy
Let's fix this by caching all the vCPU ids for which KVM_CAP_IRQ_XICS was
enabled. This also drops the now useless boolean flag from ICPState.
Reported-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function only does hypercall and RTAS-call registration, and thus
never returns an error. This patch adapt the prototype to reflect that.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerPCCPU typedef is included twice if a file includes
both hw/ppc/xics.h and target/ppc/cpu-qom.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Kernel commit 17d48610ae0f ("KVM: PPC: Book 3S: XICS: Implement ICS
P/Q states") added new bits to the state used by KVM IRQs. Currently,
QEMU does not preserve these bits, so migrating (or otherwise saving
and restoring) the guest state causes the P and Q bits to be cleared.
Clearing the P bit has no effect, because the kernel will set it based
on other data, but the loss of a set Q bit will cause a lost
interrupt.
This patch preserves the P and Q bits, correcting the problem.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This provides a new ICPState object for the PowerNV machine (POWER8).
Access to the Interrupt Management area is done though a memory
region. It contains the registers of the Interrupt Control Presenters
of each thread which are used to accept, return, forward interrupts in
the system.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It will be used by derived classes in PowerNV for customization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, all the ICPs are created before the CPUs, stored in an array
under the sPAPR machine and linked to the CPU when the core threads
are realized. This modeling brings some complexity when a lookup in
the array is required and it can be simplified by allocating the ICPs
when the CPUs are.
This is the purpose of this proposal which introduces a new 'icp_type'
field under the machine and creates the ICP objects of the right type
(KVM or not) before the PowerPCCPU object are.
This change allows more cleanups : the removal of the icps array under
the sPAPR machine and the removal of the xics_get_cpu_index_by_dt_id()
helper.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the ICPState array of the sPAPR machine is indexed with
'cpu_index' of the CPUState. This numbering of CPUs is internal to
QEMU and the guest only knows about what is exposed in the device
tree, that is the 'cpu_dt_id'. This is why sPAPR uses the helper
xics_get_cpu_index_by_dt_id() to do the mapping in a couple of places.
To provide a more generic XICS layer, we need to abstract the IRQ
'server' number and remove any assumption made on its nature. It
should not be used as a 'cpu_index' for lookups like xics_cpu_setup()
and xics_cpu_destroy() do.
To reach that goal, we choose to introduce a generic 'intc' backlink
under PowerPCCPU, and let the machine core init routine do the
ICPState lookup. The resulting object is passed on to xics_cpu_setup()
which does the store under PowerPCCPU. The IRQ 'server' number in XICS
is now generic. sPAPR uses 'cpu_dt_id' and PowerNV will use 'PIR'
number.
This also has the benefit of simplifying the sPAPR hcall routines
which do not need to do any ICPState lookups anymore.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also use an 'sPAPRRTCState' attribute under the sPAPR machine to hold
the RTC object. Overall, these changes remove an unnecessary and
implicit dependency on SysBus.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These cause compilation failures on CentOS 6 or other operating
systems with older GCCs.
Cc: David Gibson <dgibson@redhat.com>
Cc: qemu-ppc@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1488558530-21016-3-git-send-email-pbonzini@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It provides a better monitor output of the ICP and ICS objects, else
the objects are printed out of order.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICS object uses a post_load() handler which is implicitly relying
on the fact that the internal state of the ICS and ICP objects has
been restored but this is not guaranteed. So, let's move the code
under the post_load() handler of the machine where we know the objects
have been fully restored.
The icp_resend() handler of the XICSFabric QOM interface is also
removed as it is now obsolete.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XICSState classes are not used anymore. They have now been fully
deprecated by the XICSFabric QOM interface. Do the cleanups.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is nothing left related to the XICS object in the realize
functions of the KVMXICSState and XICSState class. So adapt the
interfaces to call these routines directly from the sPAPR machine init
sequence.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the last step to remove the XICSState abstraction and have the
machine hold all the objects related to interrupts : ICSs and ICPs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_dt_xics() only needs the number of servers to build the device
tree nodes. Let's change the routine interface to reflect that.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also introduce a xics_icp_get() helper to simplify the changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cpu_setup() handler is currently under the XICSState class but it
really belongs under ICPState as it is setting up an individual vCPU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cpu_setup() handler currently takes a 'XICSState *' argument to
grab the kernel ICP file descriptor. This interface can be simplified
by using the 'xics' backlink of the ICP object.
This change is also required by subsequent patches which makes use of
the QOM interface for XICS.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Let's add two new handlers for ICPs. One is to get an ICP object from
a server number and a second is to resend the irqs when needed.
The icp_resend() handler is a temporary workaround needed by the
ics-simple post_load() handler. It will be removed when the post_load
portion can be done at the machine level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is not used anymore.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
