I want to name a new class QAPISchema.
While there, make it a new-style class.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1442401589-24189-2-git-send-email-armbru@redhat.com>
The xscmpodp and xscmpudp instructions only have the AX, BX bits in
there encoding, the lowest bit (usually TX) is marked as an invalid
bit. We therefore can't decode them with GEN_XX2FORM, which decodes
the two lowest bit.
Introduce a new form GEN_XX2FORM, which decodes AX and BX and mark
the lowest bit as invalid.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
For vector instructions, the helpers get pointers to the vector register
in arguments. Some operands might point to the same register, including
the operand holding the result.
When emulating instructions which access the vector elements in a
non-linear way, we need to store the result in an temporary variable.
This fixes openssl when emulating a POWER8 CPU.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current U-Boot binary in QEMU has a bug where it fails to support
dynamic CCSR addressing. Without this support, u-boot can not boot the
ppce500 machine anymore. This has been fixed upstream in u-boot commit
e834975b.
Update the u-boot blob we carry in QEMU to the latest u-boot upstream,
so that we can successfully run u-boot with the ppce500 machine again.
CC: qemu-stable@nongnu.org
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Thomas Huth <thuth@redhat.com>
We are setting SRR0 to the instruction before the one causing the
unaligned exception. A quick testcase:
. = 0x100
.globl _start
_start:
/* Cause a 0x600 */
li 3,0x1
stwcx. 3,0,3
1: b 1b
. = 0x600
1: b 1b
Built into something we can load as a BIOS image:
gcc -mbig -c test.S
ld -EB -Ttext 0x0 -o test test.o
objcopy -O binary test test.bin
Run with:
qemu-system-ppc64 -nographic -bios test.bin
Shows an incorrect SRR0 (points at the li):
SRR0 0000000000000100
With the patch we get the correct SRR0:
SRR0 0000000000000104
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There is a bug in the register mask when reading
the ATMUs registers. As the result some registers
cannot be read, and read is aliased to the other
registers. Fix it.
Signed-off-by: Rudolf Marek <rudolf.marek@sysgo.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The code to flush the DBDMA channel was effectively duplicated in
dbdma_control_write(), except for the fact that the copy executed outside of a
RUN bit transition was broken by not clearing the FLUSH bit once the flush was
complete.
Newer PPC Linux kernels would timeout waiting for the FLUSH bit to clear again
after submitting a FLUSH command. Fix this by always clearing the FLUSH bit
once the channel flush is complete and removing the repeated code.
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
QEMU does have an I/O thread now, that can be interrupted at any time
because the VCPU thread runs outside the iothread mutex.
Therefore, the kvmppc_timer_hack is obsolete. Remove it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
* QOM API error handling fixes
* Performance improvements for device GPIO property creation
* Remaining conversion of QEMUMachine to QOM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=z33c
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/afaerber/tags/qom-devices-for-peter' into staging
QOM infrastructure fixes and device conversions
* QOM API error handling fixes
* Performance improvements for device GPIO property creation
* Remaining conversion of QEMUMachine to QOM
# gpg: Signature made Sat 19 Sep 2015 15:40:44 BST using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
* remotes/afaerber/tags/qom-devices-for-peter: (21 commits)
machine: Eliminate QEMUMachine and qemu_register_machine()
Revert use of DEFINE_MACHINE() for registrations of multiple machines
Use DEFINE_MACHINE() to register all machines
mac_world: Break long line
machine: DEFINE_MACHINE() macro
exynos4: Declare each QEMUMachine as a separate variable
exynos4: Use MachineClass instead of exynos4_machines array
exynos4: Use EXYNOS4210_NCPUS instead of max_cpus on error message
machine: Set MachineClass::name automatically
machine: Ensure all TYPE_MACHINE subclasses have the right suffix
mac99: Use MACHINE_TYPE_NAME to encode class name
s390: Rename s390-ccw-virtio-2.4 class name to use MACHINE_TYPE_NAME
s390-virtio: Rename machine class name to use MACHINE_TYPE_NAME
pseries: Rename machine class names to use MACHINE_TYPE_NAME
arm: Rename virt machine class to use MACHINE_TYPE_NAME
vexpress: Rename machine classes to use MACHINE_TYPE_NAME
vexpress: Don't set name on abstract class
machine: MACHINE_TYPE_NAME macro
qdev: Do not use slow [*] expansion for GPIO creation
qom: Fix invalid error check in property_get_str()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The struct is not used anymore and can be eliminated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The script used for converting from QEMUMachine had used one
DEFINE_MACHINE() per machine registered. In cases where multiple
machines are registered from one source file, avoid the excessive
generation of module init functions by reverting this unrolling.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Convert all machines to use DEFINE_MACHINE() instead of QEMUMachine
automatically using a script.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
[AF: Style cleanups, convert imx25_pdk machine]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The macro will allow easy registration of a TYPE_MACHINE subclass, using
only the machine name and a MachineClass initialization function as
parameter.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This will make the code follow the same pattern used for other machines,
and will make it easier to automatically convert the code to be
QOM-based.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
We don't need a QEMUMachine array to query max_cpus, if we can get the
corresponding MachineClass.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The code is checking smp_cpus against EXYNOS4210_NCPUS, not against
max_cpus, so use EXYNOS4210_NCPUS in the error message for consistency.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Now all TYPE_MACHINE subclasses use MACHINE_TYPE_NAME to generate the
class name. So instead of requiring each subclass to set
MachineClass::name manually, we can now set it automatically at the
TYPE_MACHINE class_base_init() function.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
[AF/ehabkost: Updated for s390-ccw machines]
[AF: Cleanup of intermediate virt and vexpress name handling]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Now that all non-abstract TYPE_MACHINE subclasses have the -machine
suffix, add an assert to ensure this will be always true.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
It will result in exactly the same class name, but it will make the code
consistent with the other classes.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Machine class names should use the "-machine" suffix to allow
class-name-based machine class lookup to work. Rename the
s390-ccw-virtio-2.4 machine class using the MACHINE_TYPE_NAME macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[AF/ehabkost: Updated for 2.5 machine]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Machine class names should use the "-machine" suffix to allow
class-name-based machine class lookup to work. Rename the s390-virtio
machine class using the MACHINE_TYPE_NAME macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Machine class names should use the "-machine" suffix to allow
class-name-based machine class lookup to work. Rename the the pseries
machine classes using the MACHINE_TYPE_NAME macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Machine class names should use the "-machine" suffix to allow
class-name-based machine class lookup to work. Rename the arm virt
machine class using the MACHINE_TYPE_NAME macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Machine class names should use the "-machine" suffix to allow
class-name-based machine class lookup to work. Rename the vexpress
machine classes using the MACHINE_TYPE_NAME macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[AF: Introduce VEXPRESS_*_MACHINE_NAME]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The MachineClass::name field won't be ever be used on TYPE_VEXPRESS, as
it is an abstract class and the machine class lookup code explicitly
skips abstract classes. We can remove it to make the code simpler.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The macro will be useful to ensure the machine class names follow the
right format to make machine class lookup by class name work correctly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Instead of computing mem_index and s_bits in both tcg_out_qemu_ld and
tcg_out_qemu_st function and passing them to tcg_out_tlb_load, directly
pass oi to the tcg_out_tlb_load function and compute mem_index and
s_bits there.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Somehow the tcg_out_addsub2 function ended-up in the middle of the
qemu_ld/st related functions. Move it with other arithmetics related
functions.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The MIPS TCG backend implements qemu_ld with 64-bit targets using the v0
register (base) as a temporary to load the upper half of the QEMU TLB
comparator (see line 5 below), however this happens before the input
address is used (line 8 to mask off the low bits for the TLB
comparison, and line 12 to add the host-guest offset). If the input
address (addrl) also happens to have been placed in v0 (as in the second
column below), it gets clobbered before it is used.
addrl in t2 addrl in v0
1 srl a0,t2,0x7 srl a0,v0,0x7
2 andi a0,a0,0x1fe0 andi a0,a0,0x1fe0
3 addu a0,a0,s0 addu a0,a0,s0
4 lw at,9136(a0) lw at,9136(a0) set TCG_TMP0 (at)
5 lw v0,9140(a0) lw v0,9140(a0) set base (v0)
6 li t9,-4093 li t9,-4093
7 lw a0,9160(a0) lw a0,9160(a0) set addend (a0)
8 and t9,t9,t2 and t9,t9,v0 use addrl
9 bne at,t9,0x836d8c8 bne at,t9,0x836d838 use TCG_TMP0
10 nop nop
11 bne v0,t8,0x836d8c8 bne v0,a1,0x836d838 use base
12 addu v0,a0,t2 addu v0,a0,v0 use addrl, addend
13 lw t0,0(v0) lw t0,0(v0)
Fix by using TCG_TMP0 (at) as the temporary instead of v0 (base),
pushing the load on line 5 forward into the delay slot of the low
comparison (line 10). The early load of the addend on line 7 also needs
pushing even further for 64-bit targets, or it will clobber a0 before
we're done with it. The output for 32-bit targets is unaffected.
srl a0,v0,0x7
andi a0,a0,0x1fe0
addu a0,a0,s0
lw at,9136(a0)
-lw v0,9140(a0) load high comparator
li t9,-4093
-lw a0,9160(a0) load addend
and t9,t9,v0
bne at,t9,0x836d838
- nop
+ lw at,9140(a0) load high comparator
+lw a0,9160(a0) load addend
-bne v0,a1,0x836d838
+bne at,a1,0x836d838
addu v0,a0,v0
lw t0,0(v0)
Cc: qemu-stable@nongnu.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Expansion of [*] suffix is very slow because index expansion is done using
trial and error strategy, starting every time from zero and retrying with
the next index until insertion succeeds. With large number of already added
properties this process takes huge amount of time (O(n^2) complexity).
Some architectures (like ARM) use very large amount of IRQ pins in interrupt
controller models. This flaw makes machine startup extremely slow
(~20 seconds for ARM64 with 32 CPUs). This patch decreases this time down to
~10 seconds.
Also in qdev_init_gpio_out_named() memset() is now called only once for the
whole array instead of per-cell cleaning
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
When a function returns a null pointer on error and only on error, you
can do
if (!foo(foos, errp)) {
... handle error ...
}
instead of the more cumbersome
Error *err = NULL;
if (!foo(foos, &err)) {
error_propagate(errp, err);
... handle error ...
}
A StringProperty's getter, however, may return null on success! We
then fail to call visit_type_str().
Screwed up in 6a146eb, v1.1.
Fails tests/qom-test in my current, heavily hacked QAPI branch. No
reproducer for master known (but I didn't look hard).
Cc: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Andreas Färber <afaerber@suse.de>
The argument for an Error **errp parameter must point to a null
pointer. If it doesn't, and an error happens, error_set() fails its
assertion.
Instead of
foo(foos, errp);
bar(bars, errp);
you need to do something like
Error *err = NULL;
foo(foos, &err);
if (err) {
error_propagate(errp, err);
goto out;
}
bar(bars, errp);
out:
Screwed up in commit 0e55884 (v1.3.0): property_get_bool().
Screwed up in commit 1f21772 (v2.1.0): object_property_get_enum() and
object_property_get_uint16List().
Screwed up in commit a8e3fbe (v2.4.0): property_get_enum(),
property_set_enum().
Found by inspection, no actual crashes observed.
Fix them up.
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: Hu Tao <hutao@cn.fujitsu.com>
Cc: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Andreas Färber <afaerber@suse.de>
Do not open a Cocoa window when another display is selected that will be
initialized later. The Cocoa display cannot be selected with -display,
so there is no need to check its argument.
Signed-off-by: Rainer Müller <raimue@codingfarm.de>
Reviewed-by: Andreas Färber <andreas.faerber@web.de>
Message-id: 1441807710-25431-1-git-send-email-raimue@codingfarm.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
with write_fis_d2h and signature generation tidied up,
let's adjust the initial d2h semantics to make more sense.
The initial d2h is considered delivered if there is guest
memory to save it to.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1441140641-17631-5-git-send-email-jsnow@redhat.com
It's no longer used. We used to generate a D2H FIS based
upon the command FIS that prompted the update, but in reality,
the D2H FIS is generated purely from register state.
cmd_fis is vestigial, so get rid of it.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1441140641-17631-4-git-send-email-jsnow@redhat.com
The initial register device-to-host FIS no longer needs to specially
set certain fields, as these can be handled generically by setting those
fields explicitly with the signatures we want at port reset time.
(1) Signatures are decomposed into their four component registers and
set upon (AHCI) port reset.
(2) the signature cache register is no longer set manually per-each
device type, but instead just once during ahci_init_d2h.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1441140641-17631-3-git-send-email-jsnow@redhat.com
This check is dead due to an earlier conditional.
AHCI does not currently support hotplugging, so
checks to see if devices are present or not are useless.
Remove it.
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1441140641-17631-2-git-send-email-jsnow@redhat.com
We're supposed to abort on transfers like this, unless we fill
Word 125 of our IDENTIFY data with a default transfer size, which
we don't currently do.
This is an ATA error, not a SCSI/ATAPI one.
See ATA8-ACS3 sections 7.17.6.49 or 7.21.5.
If we don't do this, QEMU will loop forever trying to transfer
zero bytes, which isn't particularly useful.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1442253685-23349-2-git-send-email-jsnow@redhat.com
We're a little too lenient with what we'll let an ATAPI drive handle.
Clamp down on the IDE command execution table to remove CD_OK permissions
from commands that are not and have never been ATAPI commands.
For ATAPI command validity, please see:
- ATA4 Section 6.5 ("PACKET Command feature set")
- ATA8/ACS Section 4.3 ("The PACKET feature set")
- ACS3 Section 4.3 ("The PACKET feature set")
ACS3 has a historical command validity table in Table B.4
("Historical Command Assignments") that can be referenced to find when
a command was introduced, deprecated, obsoleted, etc.
The only reference for ATAPI command validity is by checking that
version's PACKET feature set section.
ATAPI was introduced by T13 into ATA4, all commands retired prior to ATA4
therefore are assumed to have never been ATAPI commands.
Mandatory commands, as listed in ATA8-ACS3, are:
- DEVICE RESET
- EXECUTE DEVICE DIAGNOSTIC
- IDENTIFY DEVICE
- IDENTIFY PACKET DEVICE
- NOP
- PACKET
- READ SECTOR(S)
- SET FEATURES
Optional commands as listed in ATA8-ACS3, are:
- FLUSH CACHE
- READ LOG DMA EXT
- READ LOG EXT
- WRITE LOG DMA EXT
- WRITE LOG EXT
All other commands are illegal to send to an ATAPI device and should
be rejected by the device.
CD_OK removal justifications:
0x06 WIN_DSM Defined in ACS2. Not valid for ATAPI.
0x21 WIN_READ_ONCE Retired in ATA5. Not ATAPI in ATA4.
0x94 WIN_STANDBYNOW2 Retired in ATA4. Did not coexist with ATAPI.
0x95 WIN_IDLEIMMEDIATE2 Retired in ATA4. Did not coexist with ATAPI.
0x96 WIN_STANDBY2 Retired in ATA4. Did not coexist with ATAPI.
0x97 WIN_SETIDLE2 Retired in ATA4. Did not coexist with ATAPI.
0x98 WIN_CHECKPOWERMODE2 Retired in ATA4. Did not coexist with ATAPI.
0x99 WIN_SLEEPNOW2 Retired in ATA4. Did not coexist with ATAPI.
0xE0 WIN_STANDBYNOW1 Not part of ATAPI in ATA4, ACS or ACS3.
0xE1 WIN_IDLEIMMDIATE Not part of ATAPI in ATA4, ACS or ACS3.
0xE2 WIN_STANDBY Not part of ATAPI in ATA4, ACS or ACS3.
0xE3 WIN_SETIDLE1 Not part of ATAPI in ATA4, ACS or ACS3.
0xE4 WIN_CHECKPOWERMODE1 Not part of ATAPI in ATA4, ACS or ACS3.
0xE5 WIN_SLEEPNOW1 Not part of ATAPI in ATA4, ACS or ACS3.
0xF8 WIN_READ_NATIVE_MAX Obsoleted in ACS3. Not ATAPI in ATA4 or ACS.
This patch fixes a divide by zero fault that can be caused by sending
the WIN_READ_NATIVE_MAX command to an ATAPI drive, which causes it to
attempt to use zeroed CHS values to perform sector arithmetic.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1441816082-21031-1-git-send-email-jsnow@redhat.com
CC: qemu-stable@nongnu.org
Fix the pattern generation to actually be interesting,
and make sure all buffers in the ahci-test actually use it.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1441926555-19471-2-git-send-email-jsnow@redhat.com
Commit ef701d7 screwed up handling of out-of-memory conditions.
Before the commit, we report the error and exit(1), in one place. The
commit lifts the error handling up the call chain some, to three
places. Fine. Except it uses &error_abort in these places, changing
the behavior from exit(1) to abort(), and thus undoing the work of
commit 3922825 "exec: Don't abort when we can't allocate guest
memory".
The previous two commits fixed one of the three places, another one
was fixed in commit 33e0eb5. This commit fixes the third one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1441983105-26376-5-git-send-email-armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Commit ef701d7 screwed up handling of out-of-memory conditions.
Before the commit, we report the error and exit(1), in one place. The
commit lifts the error handling up the call chain some, to three
places. Fine. Except it uses &error_abort in these places, changing
the behavior from exit(1) to abort(), and thus undoing the work of
commit 3922825 "exec: Don't abort when we can't allocate guest
memory".
The previous commit fixed up uses of memory_region_init_ram(). One of
them was replaced by memory_region_init_resizeable_ram() [sic!] in
commit a166614, so Coccinelle missed it. Fix it up.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1441983105-26376-4-git-send-email-armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Symptom:
$ qemu-system-x86_64 -m 10000000
Unexpected error in ram_block_add() at /work/armbru/qemu/exec.c:1456:
upstream-qemu: cannot set up guest memory 'pc.ram': Cannot allocate memory
Aborted (core dumped)
Root cause: commit ef701d7 screwed up handling of out-of-memory
conditions. Before the commit, we report the error and exit(1), in
one place, ram_block_add(). The commit lifts the error handling up
the call chain some, to three places. Fine. Except it uses
&error_abort in these places, changing the behavior from exit(1) to
abort(), and thus undoing the work of commit 3922825 "exec: Don't
abort when we can't allocate guest memory".
The three places are:
* memory_region_init_ram()
Commit 4994653 (right after commit ef701d7) lifted the error
handling further, through memory_region_init_ram(), multiplying the
incorrect use of &error_abort. Later on, imitation of existing
(bad) code may have created more.
* memory_region_init_ram_ptr()
The &error_abort is still there.
* memory_region_init_rom_device()
Doesn't need fixing, because commit 33e0eb5 (soon after commit
ef701d7) lifted the error handling further, and in the process
changed it from &error_abort to passing it up the call chain.
Correct, because the callers are realize() methods.
Fix the error handling after memory_region_init_ram() with a
Coccinelle semantic patch:
@r@
expression mr, owner, name, size, err;
position p;
@@
memory_region_init_ram(mr, owner, name, size,
(
- &error_abort
+ &error_fatal
|
err@p
)
);
@script:python@
p << r.p;
@@
print "%s:%s:%s" % (p[0].file, p[0].line, p[0].column)
When the last argument is &error_abort, it gets replaced by
&error_fatal. This is the fix.
If the last argument is anything else, its position is reported. This
lets us check the fix is complete. Four positions get reported:
* ram_backend_memory_alloc()
Error is passed up the call chain, ultimately through
user_creatable_complete(). As far as I can tell, it's callers all
handle the error sanely.
* fsl_imx25_realize(), fsl_imx31_realize(), dp8393x_realize()
DeviceClass.realize() methods, errors handled sanely further up the
call chain.
We're good. Test case again behaves:
$ qemu-system-x86_64 -m 10000000
qemu-system-x86_64: cannot set up guest memory 'pc.ram': Cannot allocate memory
[Exit 1 ]
The next commits will repair the rest of commit ef701d7's damage.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1441983105-26376-3-git-send-email-armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Similar to error_abort, but doesn't report where the error was
created, and terminates the process with exit(1) rather than abort().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1441983105-26376-2-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
