HP-UX 10.20 seems to make the lsi53c895a spinning on a memory location
under certain circumstances. As the SCSI controller and CPU are not
running at the same time this loop will never finish. After some
time, the check loop interrupts with a unexpected device disconnect.
This works, but is slow because the kernel resets the scsi controller.
Instead of signaling UDC, start a timer and exit the loop. Until the
timer fires, the CPU can process instructions which might changes the
memory location.
The limit of instructions is also reduced because scripts running on
the SCSI processor are usually very short. This keeps the time until
the loop is exit short.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-ID: <20240229204407.1699260-1-svens@stackframe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This function is used to set the current SCSI bus phase in the ESP_RSTAT register
without affecting any of flag bits.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The virtio-scsi Host Bus Adapter provides access to devices on a SCSI
bus. Those SCSI devices typically have a BlockBackend. When the
BlockBackend enters a drained section, the SCSI device must temporarily
stop submitting new I/O requests.
Implement this behavior by temporarily stopping virtio-scsi virtqueue
processing when one of the SCSI devices enters a drained section. The
new scsi_device_drained_begin() API allows scsi-disk to message the
virtio-scsi HBA.
scsi_device_drained_begin() uses a drain counter so that multiple SCSI
devices can have overlapping drained sections. The HBA only sees one
pair of .drained_begin/end() calls.
After this commit, virtio-scsi no longer depends on hw/virtio's
ioeventfd aio_set_event_notifier(is_external=true). This commit is a
step towards removing the aio_disable_external() API.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230516190238.8401-19-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The MODE SELECT command can contain an optional block descriptor that can be used
to set the device block size. If the block descriptor is present then update the
block size on the SCSI device accordingly.
This allows CDROMs to be used with A/UX which requires a CDROM drive which is
capable of switching from a 2048 byte sector size to a 512 byte sector size.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When A/UX configures the CDROM device it sends a truncated MODE SELECT request
for page 1 (MODE_PAGE_R_W_ERROR) which is only 6 bytes in length rather than
10. This seems to be due to bug in Apple's code which calculates the CDB message
length incorrectly.
The work at [1] suggests that this truncated request is accepted on real
hardware whereas in QEMU it generates an INVALID_PARAM_LEN sense code which
causes A/UX to get stuck in a loop retrying the command in an attempt to succeed.
Alter the mode page request length check so that truncated requests are allowed
if the SCSI_DISK_QUIRK_MODE_PAGE_TRUNCATED quirk is enabled, whilst also adding a
trace event to enable the condition to be detected.
[1] https://68kmla.org/bb/index.php?threads/scsi2sd-project-anyone-interested.29040/page-7#post-316444
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When initialising a drive ready to install MacOS, Apple HD SC Setup first attempts
to format the drive. Add a simple FORMAT UNIT command which simply returns success
to allow the format to succeed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220622105314.802852-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
"0x%u" format is very misleading, replace by "0x%x".
Found running:
$ git grep -E '0x%[0-9]*([lL]*|" ?PRI)[dDuU]' hw/
Inspired-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20220323114718.58714-3-philippe.mathieu.daude@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
While the reply queue values fit in 16-bit, they are accessed
as 32-bit:
661: s->reply_queue_head = ldl_le_pci_dma(pcid, s->producer_pa);
662: s->reply_queue_head %= MEGASAS_MAX_FRAMES;
663: s->reply_queue_tail = ldl_le_pci_dma(pcid, s->consumer_pa);
664: s->reply_queue_tail %= MEGASAS_MAX_FRAMES;
Having:
41:#define MEGASAS_MAX_FRAMES 2048 /* Firmware limit at 65535 */
In order to update the ld/st*_pci_dma() API to pass the address
of the value to access, it is simpler to have the head/tail declared
as 32-bit values. Replace the uint16_t by uint32_t, wasting 4 bytes in
the MegasasState structure.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-20-philmd@redhat.com>
The LUN is selected with an IDENTIFY message, and persists
until the next message out phase. Instead of passing it to
do_busid_cmd, store it in ESPState. Because do_cmd can simply
skip the message out phase if cmdfifo_cdb_offset is zero, it
can now be used for the S without ATN cases as well.
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This will become more useful later when trying to debug mixed FIFO and PDMA
requests.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-8-mark.cave-ayland@ilande.co.uk>
This enables us to determine whether the command being issued is for a DMA or a
non-DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-6-mark.cave-ayland@ilande.co.uk>
Add tracepoints for SG_IO commands to allow for debugging
of SG_IO commands.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-4-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add trace events for virtio command and response tracing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-2-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200305121253.19078-8-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
While the tracing framework does not forbid trailing newline in
events format string, using them lead to confuse output.
It is the responsibility of the backend to properly end an event
line.
Some of our formats have trailing newlines, remove them.
[Fixed typo in commit description reported by Eric Blake
<eblake@redhat.com>
--Stefan]
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916095121.29506-2-philmd@redhat.com
Message-Id: <20190916095121.29506-2-philmd@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This makes trace logs much easier to read, especially for
people who are not fluent in SCSI.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190305195519.24303-5-svens@stackframe.org>
The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180917053229.4853-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In trace format '#' flag of printf is forbidden. Fix it to '0x%'.
This patch is created by the following:
check that we have a problem
> find . -name trace-events | xargs grep '%#' | wc -l
56
check that there are no cases with additional printf flags before '#'
> find . -name trace-events | xargs grep "%[-+ 0'I]+#" | wc -l
0
check that there are no wrong usage of '#' and '0x' together
> find . -name trace-events | xargs grep '0x%#' | wc -l
0
fix the problem
> find . -name trace-events | xargs sed -i 's/%#/0x%/g'
[Eric Blake noted that xargs grep '%[-+ 0'I]+#' should be xargs grep
"%[-+ 0'I]+#" instead so the shell quoting is correct.
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170731160135.12101-3-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A typo introduced in f19661c8 prevents qemu from building when configured
with --enable-trace-backend=dtrace.
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move all trace-events for files in the hw/scsi/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-16-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
