Currently we track in the TableDesc and CmdQDesc structs the state of
the GITS_BASER<n> and GITS_CBASER Valid bits. However we aren't very
consistent abut checking the valid field: we test it in update_cte()
and update_dte(), but not anywhere else we look things up in tables.
The GIC specification says that it is UNPREDICTABLE if a guest fails
to set any of these Valid bits before enabling the ITS via
GITS_CTLR.Enabled. So we can choose to handle Valid == 0 as
equivalent to a zero-length table. This is in fact how we're already
catching this case in most of the table-access paths: when Valid is 0
we leave the num_entries fields in TableDesc or CmdQDesc set to zero,
and then the out-of-bounds check "index >= num_entries" that we have
to do anyway before doing any of these table lookups will always be
true, catching the no-valid-table case without any extra code.
So we can remove the checks on the valid field from update_cte()
and update_dte(): since these happen after the bounds check there
was never any case when the test could fail. That means the valid
fields would be entirely unused, so just remove them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-11-peter.maydell@linaro.org
We use the arm_boot_info::nb_cpus field in only one place, and that
place can easily get the number of CPUs locally rather than relying
on the board code to have set the field correctly. (At least one
board, xlnx-versal-virt, does not set the field despite having more
than one CPU.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-16-peter.maydell@linaro.org
If we're using PSCI emulation to start secondary CPUs, there is no
point in writing the "secondary boot" stub code, because it will
never be used -- secondary CPUs start powered-off, and when powered
on are set to begin execution at the address specified by the guest's
power-on PSCI call, not at the stub.
Move the call to the hook that writes the secondary boot stub code so
that we can do it only if we're starting a Linux kernel and not using
PSCI.
(None of the users of the hook care about the ordering of its call
relative to anything else: they only use it to write a rom blob to
guest memory.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-14-peter.maydell@linaro.org
Instead of setting the CPU psci-conduit and start-powered-off
properties in the xlnx-versal-virt board code, set the arm_boot_info
psci_conduit field so that the boot.c code can do it.
This will fix a corner case where we were incorrectly enabling PSCI
emulation when booting guest code into EL3 because it was an ELF file
passed to -kernel. (EL3 guest code started via -bios, -pflash, or
the generic loader was already being run with PSCI emulation
disabled.)
Note that EL3 guest code has no way to turn on the secondary CPUs
because there's no emulated power controller, but this was already
true for EL3 guest code run via -bios, -pflash, or the generic
loader.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-8-peter.maydell@linaro.org
Currently we expect board code to set the psci-conduit property on
CPUs and ensure that secondary CPUs are created with the
start-powered-off property set to false, if the board wishes to use
QEMU's builtin PSCI emulation. This worked OK for the virt board
where we first wanted to use it, because the virt board directly
creates its CPUs and is in a reasonable position to set those
properties. For other boards which model real hardware and use a
separate SoC object, however, it is more awkward. Most PSCI-using
boards just set the psci-conduit board unconditionally.
This was never strictly speaking correct (because you would not be
able to run EL3 guest firmware that itself provided the PSCI
interface, as the QEMU implementation would overrule it), but mostly
worked in practice because for non-PSCI SMC calls QEMU would emulate
the SMC instruction as normal (by trapping to guest EL3). However,
we would like to make our PSCI emulation follow the part of the SMCC
specification that mandates that SMC calls with unknown function
identifiers return a failure code, which means that all SMC calls
will be handled by the PSCI code and the "emulate as normal" path
will no longer be taken.
We tried to implement that in commit 9fcd15b919
("arm: tcg: Adhere to SMCCC 1.3 section 5.2"), but this
regressed attempts to run EL3 guest code on the affected boards:
* mcimx6ul-evk, mcimx7d-sabre, orangepi, xlnx-zcu102
* for the case only of EL3 code loaded via -kernel (and
not via -bios or -pflash), virt and xlnx-versal-virt
so for the 7.0 release we reverted it (in commit 4825eaae4f).
This commit provides a mechanism that boards can use to arrange that
psci-conduit is set if running guest code at a low enough EL but not
if it would be running at the same EL that the conduit implies that
the QEMU PSCI implementation is using. (Later commits will convert
individual board models to use this mechanism.)
We do this by moving the setting of the psci-conduit and
start-powered-off properties to arm_load_kernel(). Boards which want
to potentially use emulated PSCI must set a psci_conduit field in the
arm_boot_info struct to the type of conduit they want to use (SMC or
HVC); arm_load_kernel() will then set the CPUs up accordingly if it
is not going to start the guest code at the same or higher EL as the
fake QEMU firmware would be at.
Board/SoC code which uses this mechanism should no longer set the CPU
psci-conduit property directly. It should only set the
start-powered-off property for secondaries if EL3 guest firmware
running bare metal expects that rather than the alternative "all CPUs
start executing the firmware at once".
Note that when calculating whether we are going to run guest
code at EL3, we ignore the setting of arm_boot_info::secure_board_setup,
which might cause us to run a stub bit of guest code at EL3 which
does some board-specific setup before dropping to EL2 or EL1 to
run the guest kernel. This is OK because only one board that
enables PSCI sets secure_board_setup (the highbank board), and
the stub code it writes will behave the same way whether the
one SMC call it makes is handled by "emulate the SMC" or by
"PSCI default returns an error code". So we can leave that stub
code in place until after we've changed the PSCI default behaviour;
at that point we will remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20220127154639.2090164-4-peter.maydell@linaro.org
'Or' the IRQs coming from the QSPI and QSPI DMA models. This is done for
avoiding the situation where one of the models incorrectly deasserts an
interrupt asserted from the other model (which will result in that the IRQ
is lost and will not reach guest SW).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220203151742.1457-1-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This change exposes ACPI ERST support for x86 guests.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-8-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This change introduces the public defintions for ACPI ERST.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-5-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This change reserves the PCI device_id for the new ACPI ERST
device.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-4-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The comment "disk I/O throttling" doesn't make any sense at all
any more. It was added in commit 0563e19151 to describe
bdrv_io_limits_enable()/disable(), which were removed in commit
97148076, so the comment is just a forgotten leftover.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220131125615.74612-1-eesposit@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The vhost-user-blk export runs requests asynchronously in their own
coroutine. When the vhost connection goes away and we want to stop the
vhost-user server, we need to wait for these coroutines to stop before
we can unmap the shared memory. Otherwise, they would still access the
unmapped memory and crash.
This introduces a refcount to VuServer which is increased when spawning
a new request coroutine and decreased before the coroutine exits. The
memory is only unmapped when the refcount reaches zero.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20220125151435.48792-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* Update copyright dates to 2022
* hw/armv7m: Fix broken VMStateDescription
* hw/char/exynos4210_uart: Fix crash on trying to load VM state
* rtc: Move RTC function prototypes to their own header
* xlnx-versal-virt: Support PMC SLCR
* xlnx-versal-virt: Support OSPI flash memory controller
* scripts: Explain the difference between linux-headers and standard-headers
* target/arm: Log CPU index in 'Taking exception' log
* arm_gicv3_its: Various bugfixes and cleanups
* arm_gicv3_its: Implement the missing MOVI and MOVALL commands
* ast2600: Fix address mapping of second SPI controller
* target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
-----BEGIN PGP SIGNATURE-----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=m7N5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20220128' into staging
target-arm queue:
* Update copyright dates to 2022
* hw/armv7m: Fix broken VMStateDescription
* hw/char/exynos4210_uart: Fix crash on trying to load VM state
* rtc: Move RTC function prototypes to their own header
* xlnx-versal-virt: Support PMC SLCR
* xlnx-versal-virt: Support OSPI flash memory controller
* scripts: Explain the difference between linux-headers and standard-headers
* target/arm: Log CPU index in 'Taking exception' log
* arm_gicv3_its: Various bugfixes and cleanups
* arm_gicv3_its: Implement the missing MOVI and MOVALL commands
* ast2600: Fix address mapping of second SPI controller
* target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
# gpg: Signature made Fri 28 Jan 2022 15:29:36 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20220128: (32 commits)
target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
hw/arm: ast2600: Fix address mapping of second SPI controller
hw/intc/arm_gicv3_its: Implement MOVI
hw/intc/arm_gicv3_its: Implement MOVALL
hw/intc/arm_gicv3_its: Check table bounds against correct limit
hw/intc/arm_gicv3_its: Make GITS_BASER<n> RAZ/WI for unimplemented registers
hw/intc/arm_gicv3_its: Provide read accessor for translation_ops
hw/intc/arm_gicv3: Set GICR_CTLR.CES if LPIs are supported
hw/intc/arm_gicv3_redist: Remove unnecessary zero checks
hw/intc/arm_gicv3_its: Sort ITS command list into numeric order
hw/intc/arm_gicv3: Honour GICD_CTLR.EnableGrp1NS for LPIs
hw/intc/arm_gicv3_its: Don't clear GITS_CWRITER on writes to GITS_CBASER
hw/intc/arm_gicv3_its: Don't clear GITS_CREADR when GITS_CTLR.ENABLED is set
hw/intc/arm_gicv3: Initialise dma_as in GIC, not ITS
hw/intc/arm_gicv3_its: Add tracepoints
target/arm: Log CPU index in 'Taking exception' log
scripts: Explain the difference between linux-headers and standard-headers
MAINTAINERS: Remove myself (for raspi).
MAINTAINERS: Add an entry for Xilinx Versal OSPI
hw/arm/xlnx-versal-virt: Connect mt35xu01g flashes to the OSPI
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently when we fill in a TableDesc based on the value the guest
has written to the GITS_BASER<n> register, we calculate both:
* num_entries : the number of entries in the table, constrained
by the amount of memory the guest has given it
* num_ids : the number of IDs we support for this table,
constrained by the implementation choices and the architecture
(eg DeviceIDs are 16 bits, so num_ids is 1 << 16)
When validating ITS commands, however, we check only num_ids,
thus allowing a broken guest to specify table entries that
index off the end of it. This will only corrupt guest memory,
but the ITS is supposed to reject such commands as invalid.
Instead of calculating both num_entries and num_ids, set
num_entries to the minimum of the two limits, and check that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220122182444.724087-13-peter.maydell@linaro.org
Connect the OSPI flash memory controller model (including the source and
destination DMA).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220121161141.14389-8-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of Xilinx Versal's OSPI flash memory controller.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-7-francisco.iglesias@xilinx.com
[PMM: fixed indent]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An option on real hardware when embedding a DMA engine into a peripheral
is to make the peripheral control the engine through a custom DMA control
(hardware) interface between the two. Software drivers in this scenario
configure and trigger DMA operations through the controlling peripheral's
register API (for example, writing a specific bit in a register could
propagate down to a transfer start signal on the DMA control interface).
At the same time the status, results and interrupts for the transfer might
still be intended to be read and caught through the DMA engine's register
API (and signals).
This patch adds a class 'read' method for allowing to start read transfers
from peripherals embedding and controlling the Xilinx CSU DMA engine as in
above scenario.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-6-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add in the missing includes in the header for being able to build the DMA
model when reusing it.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-5-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an orgate and 'or' the interrupts from the BBRAM and RTC models.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-3-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of Versal's PMC SLCR (system-level control registers).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-2-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
softmmu/rtc.c defines two public functions: qemu_get_timedate() and
qemu_timedate_diff(). Currently we keep the prototypes for these in
qemu-common.h, but most files don't need them. Move them to their
own header, a new include/sysemu/rtc.h.
Since the C files using these two functions did not need to include
qemu-common.h for any other reason, we can remove those include lines
when we add the include of the new rtc.h.
The license for the .h file follows that of the softmmu/rtc.c
where both the functions are defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
It's a new year; update the copyright strings for our
help/version/about information and for our documentation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220120124713.288303-1-peter.maydell@linaro.org
vof.h requires "qom/object.h" for DECLARE_CLASS_CHECKERS(),
"exec/memory.h" for address_space_read/write(),
"exec/address-spaces.h" for address_space_memory
and more importantly "cpu.h" for target_ulong.
vof.c doesn't need "exec/ram_addr.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220122003104.84391-1-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
"host" pages are related to the *host* not the *target*,
thus the qemu_host_page_size / qemu_host_page_mask variables
and the HOST_PAGE_ALIGN() / REAL_HOST_PAGE_ALIGN() macros
can be moved to "exec/cpu-common.h" which is target agnostic.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20220120000836.229419-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions are only used within their respective source files, so no
need for exporting.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20220116122327.73048-1-shentey@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that RISC-V Spike machine can use BIN BIOS images, we remove
the macros used for ELF BIOS image names.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we have to use OpenSBI firmware ELF as bios for the spike
machine because the HTIF console requires ELF for parsing "fromhost"
and "tohost" symbols.
The latest OpenSBI can now optionally pick-up HTIF register address
from HTIF DT node so using this feature spike machine can now use
OpenSBI firmware BIN as bios.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Get kernel and fdt start address in virt.c, and pass them to KVM
when cpu reset. Add kvm_riscv.h to place riscv specific interface.
In addition, PLIC is created without M-mode PLIC contexts when KVM
is enabled.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Mingwang Li <limingwang@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-id: 20220112081329.1835-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This change fixes a bug where a write only register is read.
As per https://docs.opentitan.org/hw/ip/rv_timer/doc/#register-table
the 'INTR_TEST0' register is write only.
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220110051606.4031241-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
* hw/intc/arm_gicv3_its: Fix various minor bugs
* hw/arm/aspeed: Add the i3c device to the AST2600 SoC
* hw/arm: kudo: add lm75s behind bus 1 switch at 75
* hw/arm/virt: Fix support for running guests on hosts
with restricted IPA ranges
* hw/intc/arm_gic: Allow reset of the running priority
* hw/intc/arm_gic: Implement read of GICC_IIDR
* hw/arm/virt: Support for virtio-mem-pci
* hw/arm/virt: Support CPU cluster on ARM virt machine
* docs/can: convert to restructuredText
* hw/net: Move MV88W8618 network device out of hw/arm/ directory
* hw/arm/virt: KVM: Enable PAuth when supported by the host
-----BEGIN PGP SIGNATURE-----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=hPal
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20220120-1' into staging
target-arm:
* hw/intc/arm_gicv3_its: Fix various minor bugs
* hw/arm/aspeed: Add the i3c device to the AST2600 SoC
* hw/arm: kudo: add lm75s behind bus 1 switch at 75
* hw/arm/virt: Fix support for running guests on hosts
with restricted IPA ranges
* hw/intc/arm_gic: Allow reset of the running priority
* hw/intc/arm_gic: Implement read of GICC_IIDR
* hw/arm/virt: Support for virtio-mem-pci
* hw/arm/virt: Support CPU cluster on ARM virt machine
* docs/can: convert to restructuredText
* hw/net: Move MV88W8618 network device out of hw/arm/ directory
* hw/arm/virt: KVM: Enable PAuth when supported by the host
# gpg: Signature made Thu 20 Jan 2022 16:12:12 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20220120-1: (38 commits)
hw/intc/arm_gicv3: Check for !MEMTX_OK instead of MEMTX_ERROR
hw/intc/arm_gicv3_its: Range-check ICID before indexing into collection table
hw/intc/arm_gicv3_its: Check indexes before use, not after
hw/intc/arm_gicv3_its: Factor out "find address of table entry" code
hw/intc/arm_gicv3_its: Fix return codes in process_mapd()
hw/intc/arm_gicv3_its: Fix return codes in process_mapc()
hw/intc/arm_gicv3_its: Fix return codes in process_mapti()
hw/intc/arm_gicv3_its: Refactor process_its_cmd() to reduce nesting
hw/intc/arm_gicv3_its: Fix return codes in process_its_cmd()
hw/intc/arm_gicv3_its: Use enum for return value of process_* functions
hw/intc/arm_gicv3_its: Don't use data if reading command failed
hw/intc/arm_gicv3_its: Fix handling of process_its_cmd() return value
hw/intc/arm_gicv3_its: Convert int ID check to num_intids convention
hw/intc/arm_gicv3_its: Fix event ID bounds checks
hw/arm/aspeed: Add the i3c device to the AST2600 SoC
hw/misc/aspeed_i3c.c: Introduce a dummy AST2600 I3C model.
hw/arm: kudo add lm75s behind bus 1 switch at 75
hw/arm/virt: Drop superfluous checks against highmem
hw/arm/virt: Disable highmem devices that don't fit in the PA range
hw/arm/virt: Use the PA range to compute the memory map
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Aspeed 2600 SDK enables I3C support by default. The I3C driver will try
to reset the device controller and set it up through device address table
register. This dummy model responds to these registers with default values
as listed in the ast2600v10 datasheet chapter 54.2.
This avoids a guest machine kernel panic due to referencing an
invalid kernel address if the device address table register isn't
set correctly.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Graeme Gregory <quic_ggregory@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Graeme Gregory <quic_ggregory@quicinc.com>
Message-id: 20220111084546.4145785-2-troy_lee@aspeedtech.com
[PMM: tidied commit message; fixed format strings]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like we can control the enablement of the highmem PCIe region
using highmem_ecam, let's add a control for the highmem GICv3
redistributor region.
Similarily to highmem_ecam, these redistributors are disabled when
highmem is off.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-3-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like we can control the enablement of the highmem PCIe ECAM
region using highmem_ecam, let's add a control for the highmem
PCIe MMIO region.
Similarily to highmem_ecam, this region is disabled when highmem
is off.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-2-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Marvell 88W8618 network device is hidden in the Musicpal
machine. Move it into a new unit file under the hw/net/ directory.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the mem_size of the segment is bigger than the file_size,
and if this space doesn't overlap another segment, it needs
to be cleared.
This bug is very similar to the one we had for linux-user,
22d113b52f ("linux-user: Fix loading of BSS segments"),
where .bss section is encoded as an extension of the the data
one by setting the segment p_memsz > p_filesz.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
[PMD: Use recently added address_space_set()]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220115203725.3834712-3-laurent@vivier.eu>
dma_memory_set() does a DMA barrier, set the address space with
a constant value. The constant value filling code is not specific
to DMA and can be used for AddressSpace. Extract it as a new
helper: address_space_set().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[lv: rebase]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220115203725.3834712-2-laurent@vivier.eu>
- fix compiler warnings with ui and sdl
- update QXL/spice dependancy
- skip I/O tests on Alpine
- update fedora image to latest version
- integrate lcitool and regenerate docker images
- favour CONFIG_LINUX_USER over CONFIG_LINUX
- add libfuse3 dependencies to docker images
- add dtb-kaslr-seed control knob to virt machine
- fix build breakage from HMP update
- update docs for C standard and suffix usage
- add more logging for debugging user hole finding
- expand reserve for brk() for static 64 bit programs
- fix bug with linux-user hole calculation
- avoid affecting flags when printing results in float tests
- add float reference files for ppc64
- update FreeBSD to 12.3
- add bison dependancy to tricore images
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmHm7y4ACgkQ+9DbCVqe
KkSsDwgAgWiOUtnPxNnZ3PuLQpIDCGSotjshCXo9PhPu/SWedvMfTftPU+g3wxbl
+A2GZcNnVPaOrJo7hfDtOtir9UJUFTmyv8KtPhUYmtxxiv3HWM1RvgrBQnMEvo5A
GFAq6jSFclH4HTSxz4FHbEl0TM3feQbSfbMWI6Q1Q+aPm8hWSzhClIqBCwsJJdm8
hi76BE9o94BtvA6Qv2CoPvGsOzpV0X0VXaljf1W927BzJu+b0wEGwIm61+eovNsh
DS2kDZk+PpiYeRN/oC40Z6ozR/Lf/jZ/87AnN3gV/yLDwa5cafA+GtmcKMx1IJIc
BVm0bJo+KzHfYiVjYTJhsU7C2W71PA==
=uBQq
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-for-7.0-180122-2' into staging
Various testing and other misc updates:
- fix compiler warnings with ui and sdl
- update QXL/spice dependancy
- skip I/O tests on Alpine
- update fedora image to latest version
- integrate lcitool and regenerate docker images
- favour CONFIG_LINUX_USER over CONFIG_LINUX
- add libfuse3 dependencies to docker images
- add dtb-kaslr-seed control knob to virt machine
- fix build breakage from HMP update
- update docs for C standard and suffix usage
- add more logging for debugging user hole finding
- expand reserve for brk() for static 64 bit programs
- fix bug with linux-user hole calculation
- avoid affecting flags when printing results in float tests
- add float reference files for ppc64
- update FreeBSD to 12.3
- add bison dependancy to tricore images
# gpg: Signature made Tue 18 Jan 2022 16:47:42 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-for-7.0-180122-2: (31 commits)
docker: include bison in debian-tricore-cross
FreeBSD: Upgrade to 12.3 release
test/tcg/ppc64le: Add float reference files
tests/tcg/multiarch: Read fp flags before printf
linux-user: don't adjust base of found hole
linux-user/elfload: add extra logging for hole finding
linux-user: expand reserved brk space for 64bit guests
docs/devel: more documentation on the use of suffixes
docs/devel: update C standard to C11
monitor: move x-query-profile into accel/tcg to fix build
hw/arm: add control knob to disable kaslr_seed via DTB
tests/docker: add libfuse3 development headers
tests/tcg: use CONFIG_LINUX_USER, not CONFIG_LINUX
tests/docker: auto-generate alpine.docker with lcitool
tests/docker: fully expand the alpine package list
tests/docker: fix sorting of alpine image package lists
tests/docker: updates to alpine package list
.gitlab-ci.d/cirrus: auto-generate variables with lcitool
tests/docker: remove ubuntu.docker container
tests/docker: auto-generate opensuse-leap.docker with lcitool
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* More documentation updates (Leonardo)
* Fixes for the 7448 CPU (Fabiano and Cedric)
* Final removal of 403 CPUs and the .load_state_old handler (Cedric)
* More cleanups of PHB4 models (Daniel and Cedric)
-----BEGIN PGP SIGNATURE-----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=M4/2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-ppc-20220118' into staging
ppc 7.0 queue:
* More documentation updates (Leonardo)
* Fixes for the 7448 CPU (Fabiano and Cedric)
* Final removal of 403 CPUs and the .load_state_old handler (Cedric)
* More cleanups of PHB4 models (Daniel and Cedric)
# gpg: Signature made Tue 18 Jan 2022 11:59:16 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-ppc-20220118: (31 commits)
ppc/pnv: Remove PHB4 version property
ppc/pnv: Add a 'rp_model' class attribute for the PHB4 PEC
ppc/pnv: Move root port allocation under pnv_pec_default_phb_realize()
ppc/pnv: rename pnv_pec_stk_update_map()
ppc/pnv: remove PnvPhb4PecStack object
ppc/pnv: make PECs create and realize PHB4s
ppc/pnv: remove PnvPhb4PecStack::stack_no
ppc/pnv: move default_phb_realize() to pec_realize()
ppc/pnv: remove stack pointer from PnvPHB4
ppc/pnv: reduce stack->stack_no usage
ppc/pnv: introduce PnvPHB4 'pec' property
ppc/pnv: move phb_regs_mr to PnvPHB4
ppc/pnv: move nest_regs_mr to PnvPHB4
ppc/pnv: change pnv_pec_stk_update_map() to use PnvPHB4
ppc/pnv: move nest_regs[] to PnvPHB4
ppc/pnv: move mmbar0/mmbar1 and friends to PnvPHB4
ppc/pnv: change pnv_phb4_update_regions() to use PnvPHB4
ppc/pnv: move intbar to PnvPHB4
ppc/pnv: move phbbar to PnvPHB4
ppc/pnv: move PCI registers to PnvPHB4
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using _qemu is a little confusing. Let's use _compat for these sorts
of things. We should also mention _impl which is another common suffix
in the code base.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20220105135009.1584676-25-alex.bennee@linaro.org>
Generally a guest needs an external source of randomness to properly
enable things like address space randomisation. However in a trusted
boot environment where the firmware will cryptographically verify
components having random data in the DTB will cause verification to
fail. Add a control knob so we can prevent this being added to the
system DTB.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20220105135009.1584676-22-alex.bennee@linaro.org>
On Alpine, SDL is built with directfb support and this triggers warnings
during QEMU build
In file included from /usr/include/directfb/direct/thread.h:38,
from /usr/include/directfb/direct/debug.h:43,
from /usr/include/directfb/direct/interface.h:36,
from /usr/include/directfb/directfb.h:49,
from /usr/include/SDL2/SDL_syswm.h:80,
from /builds/berrange/qemu/include/ui/sdl2.h:8,
from ../ui/sdl2-gl.c:31:
/usr/include/directfb/direct/os/waitqueue.h:41:25: error: redundant redeclaration of 'direct_waitqueue_init' [-Werror=redundant-decls]
41 | DirectResult DIRECT_API direct_waitqueue_init ( DirectWaitQueue *queue );
| ^~~~~~~~~~~~~~~~~~~~~
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20211215141949.3512719-5-berrange@redhat.com>
Message-Id: <20220105135009.1584676-5-alex.bennee@linaro.org>
spice updated the spelling (and arguments) of "attache_worker" in
0.15.0. Update QEMU to match, preventing -Wdeprecated-declarations
compilations from reporting build errors.
See also:
974692bda1
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20211215141949.3512719-3-berrange@redhat.com>
Message-Id: <20220105135009.1584676-3-alex.bennee@linaro.org>
PHB5 will introduce its own root port model. Prepare ground for it.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220117122753.1655504-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
All the complexity that was scattered between PnvPhb4PecStack and
PnvPHB4 are now centered in the PnvPHB4 device. PnvPhb4PecStack does not
serve any purpose in the current code base.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220114180719.52117-8-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This patch changes the design of the PEC device to create and realize PHB4s
instead of PecStacks. After all the recent changes, PHB4s now contain all
the information needed for their proper functioning, not relying on PecStack
in any capacity.
All changes are being made in a single patch to avoid renaming parts of
the PecState and leaving the code in a strange way. E.g. rename
PecClass->num_stacks to num_phbs, which would then read a
pnv_pec_num_stacks[] array. To avoid mixing the old and new design more
than necessary it's clearer to do these changes in a single step.
The name changes made are:
- in PnvPhb4PecState:
* rename 'num_stacks' to 'num_phbs'
* remove the pec->stacks[] array. Current code relies on the
pec->stacks[] obj acting as a simple container, without ever accessing
pec->stacks[] for any other purpose. Instead of converting this into a
pec->phbs[] array, remove it
- in PnvPhb4PecClass, rename *num_stacks to *num_phbs;
- pnv_pec_num_stacks[] is renamed to pnv_pec_num_phbs[].
The logical changes:
- pnv_pec_default_phb_realize():
* init and set the properties of the PnvPHB4 qdev
* do not use stack->phb anymore;
- pnv_pec_realize():
* use the new default_phb_realize() to init/realize each PHB if
running with defaults;
- pnv_pec_instance_init(): removed since we're creating the PHBs during
pec_realize();
- pnv_phb4_get_stack():
* renamed to pnv_phb4_get_pec() and returns a PnvPhb4PecState*;
- pnv_phb4_realize(): use 'phb->pec' instead of 'stack'.
This design change shouldn't caused any behavioral change in the runtime
of the machine.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220114180719.52117-7-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
pnv_pec_default_phb_realize() stopped using it after the previous patch and
no one else is using it.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220114180719.52117-6-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
