Introducing new migration state "postcopy-recover". If a migration
procedure is paused and the connection is rebuilt afterward
successfully, we'll switch the source VM state from "postcopy-paused" to
the new state "postcopy-recover", then we'll do the resume logic in the
migration thread (along with the return path thread).
This patch only do the state switch on source side. Another following up
patch will handle the state switching on destination side using the same
status bit.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180502104740.12123-10-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
---
s/2.11/2.13/
This patch detects the "resume" flag of migration command, rebuild the
channels only if the flag is set.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180502104740.12123-9-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It will be used when we want to resume one paused migration.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180502104740.12123-8-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
---
s/2.12/2.13/
Allows the fault thread to stop handling page faults temporarily. When
network failure happened (and if we expect a recovery afterwards), we
should not allow the fault thread to continue sending things to source,
instead, it should halt for a while until the connection is rebuilt.
When the dest main thread noticed the failure, it kicks the fault thread
to switch to pause state.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180502104740.12123-7-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Let the thread pause for network issues.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180502104740.12123-6-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
When there is IO error on the incoming channel (e.g., network down),
instead of bailing out immediately, we allow the dst vm to switch to the
new POSTCOPY_PAUSE state. Currently it is still simple - it waits the
new semaphore, until someone poke it for another attempt.
One note is that here on ram loading thread we cannot detect the
POSTCOPY_ACTIVE state, but we need to detect the more specific
POSTCOPY_INCOMING_RUNNING state, to make sure we have already loaded all
the device states.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180502104740.12123-5-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Now when network down for postcopy, the source side will not fail the
migration. Instead we convert the status into this new paused state, and
we will try to wait for a rescue in the future.
If a recovery is detected, migration_thread() will reset its local
variables to prepare for that.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180502104740.12123-4-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Introducing a new state "postcopy-paused", which can be used when the
postcopy migration is paused. It is targeted for postcopy network
failure recovery.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180502104740.12123-3-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We need to make sure that we have started all the multifd threads.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Now that we can safely call QOBJECT() on QObject * as well as its
subtypes, we can have macros qobject_ref() / qobject_unref() that work
everywhere instead of having to use QINCREF() / QDECREF() for QObject
and qobject_incref() / qobject_decref() for its subtypes.
The replacement is mechanical, except I broke a long line, and added a
cast in monitor_qmp_cleanup_req_queue_locked(). Unlike
qobject_decref(), qobject_unref() doesn't accept void *.
Note that the new macros evaluate their argument exactly once, thus no
need to shout them.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180419150145.24795-4-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Rebased, semantic conflict resolved, commit message improved]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Postcopy total blocktime is available on destination side only.
But query-migrate was possible only for source. This patch
adds ability to call query-migrate on destination.
To be able to see postcopy blocktime, need to request postcopy-blocktime
capability.
The query-migrate command will show following sample result:
{"return":
"postcopy-vcpu-blocktime": [115, 100],
"status": "completed",
"postcopy-blocktime": 100
}}
postcopy_vcpu_blocktime contains list, where the first item is the first
vCPU in QEMU.
This patch has a drawback, it combines states of incoming and
outgoing migration. Ongoing migration state will overwrite incoming
state. Looks like better to separate query-migrate for incoming and
outgoing migration or add parameter to indicate type of migration.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alexey Perevalov <a.perevalov@samsung.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1521742647-25550-7-git-send-email-a.perevalov@samsung.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Right now it could be used on destination side to
enable vCPU blocktime calculation for postcopy live migration.
vCPU blocktime - it's time since vCPU thread was put into
interruptible sleep, till memory page was copied and thread awake.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alexey Perevalov <a.perevalov@samsung.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1521742647-25550-2-git-send-email-a.perevalov@samsung.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This reverts commit 0746a92612.
Discussion with kwolf suggests this is actually an API change that
we need to gate on a capability. Push to 2.13.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Activating the block devices causes the locks to be taken on
the backing file. If we're running with -S and the destination libvirt
hasn't started the destination with 'cont', it's expecting the locks are
still untaken.
Don't activate the block devices if we're not going to autostart the VM;
'cont' already will do that anyway.
bz: https://bugzilla.redhat.com/show_bug.cgi?id=1560854
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20180328170207.49512-1-dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fix the case where when a migration with a bad protocol is tried,
we leave the block migration capability set.
(This is a cut down version of my 'migration: Fix block failure cases'
where it's other case was fixed by Peter's dd0ee30cae )
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20180316202114.32345-1-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Allow other userfaultfd's to be registered into the fault thread
so that handlers for shared memory can get responses.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Postcopy migration of dirty bitmaps. Only named dirty bitmaps are migrated.
If destination qemu is already containing a dirty bitmap with the same name
as a migrated bitmap (for the same node), then, if their granularities are
the same the migration will be done, otherwise the error will be generated.
If destination qemu doesn't contain such bitmap it will be created.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20180313180320.339796-12-vsementsov@virtuozzo.com
[Changed '+' to '*' as per list discussion. --js]
Signed-off-by: John Snow <jsnow@redhat.com>
Allow migrate-start-postcopy for any postcopy type
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20180313180320.339796-11-vsementsov@virtuozzo.com
There would be savevm states (dirty-bitmap) which can migrate only in
postcopy stage. The corresponding pending is introduced here.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20180313180320.339796-6-vsementsov@virtuozzo.com
When setting migration capabilities via QMP/HMP, we'll apply them even
if the capability check failed. Fix it.
Fixes: 4a84214ebe ("migration: provide migrate_caps_check()", 2017-07-18)
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180305094938.31374-1-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Spotted thanks to ASAN:
QTEST_QEMU_BINARY=x86_64-softmmu/qemu-system-x86_64 tests/migration-test -p /x86_64/migration/bad_dest
==30302==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 48 byte(s) in 1 object(s) allocated from:
#0 0x7f60efba1a38 in __interceptor_calloc (/lib64/libasan.so.4+0xdea38)
#1 0x7f60eef3cf75 in g_malloc0 ../glib/gmem.c:124
#2 0x55ca9094702c in error_copy /home/elmarco/src/qemu/util/error.c:203
#3 0x55ca9037a30f in migrate_set_error /home/elmarco/src/qemu/migration/migration.c:1139
#4 0x55ca9037a462 in migrate_fd_error /home/elmarco/src/qemu/migration/migration.c:1150
#5 0x55ca9038162b in migrate_fd_connect /home/elmarco/src/qemu/migration/migration.c:2411
#6 0x55ca90386e41 in migration_channel_connect /home/elmarco/src/qemu/migration/channel.c:81
#7 0x55ca9038335e in socket_outgoing_migration /home/elmarco/src/qemu/migration/socket.c:85
#8 0x55ca9083dd3a in qio_task_complete /home/elmarco/src/qemu/io/task.c:142
#9 0x55ca9083d6cc in gio_task_thread_result /home/elmarco/src/qemu/io/task.c:88
#10 0x7f60eef37317 in g_idle_dispatch ../glib/gmain.c:5552
#11 0x7f60eef3490b in g_main_dispatch ../glib/gmain.c:3182
#12 0x7f60eef357ac in g_main_context_dispatch ../glib/gmain.c:3847
#13 0x55ca90927231 in glib_pollfds_poll /home/elmarco/src/qemu/util/main-loop.c:214
#14 0x55ca90927420 in os_host_main_loop_wait /home/elmarco/src/qemu/util/main-loop.c:261
#15 0x55ca909275fa in main_loop_wait /home/elmarco/src/qemu/util/main-loop.c:515
#16 0x55ca8fc1c2a4 in main_loop /home/elmarco/src/qemu/vl.c:1942
#17 0x55ca8fc2eb3a in main /home/elmarco/src/qemu/vl.c:4724
#18 0x7f60e4082009 in __libc_start_main (/lib64/libc.so.6+0x21009)
Indirect leak of 45 byte(s) in 1 object(s) allocated from:
#0 0x7f60efba1850 in malloc (/lib64/libasan.so.4+0xde850)
#1 0x7f60eef3cf0c in g_malloc ../glib/gmem.c:94
#2 0x7f60eef3d1cf in g_malloc_n ../glib/gmem.c:331
#3 0x7f60eef596eb in g_strdup ../glib/gstrfuncs.c:363
#4 0x55ca90947085 in error_copy /home/elmarco/src/qemu/util/error.c:204
#5 0x55ca9037a30f in migrate_set_error /home/elmarco/src/qemu/migration/migration.c:1139
#6 0x55ca9037a462 in migrate_fd_error /home/elmarco/src/qemu/migration/migration.c:1150
#7 0x55ca9038162b in migrate_fd_connect /home/elmarco/src/qemu/migration/migration.c:2411
#8 0x55ca90386e41 in migration_channel_connect /home/elmarco/src/qemu/migration/channel.c:81
#9 0x55ca9038335e in socket_outgoing_migration /home/elmarco/src/qemu/migration/socket.c:85
#10 0x55ca9083dd3a in qio_task_complete /home/elmarco/src/qemu/io/task.c:142
#11 0x55ca9083d6cc in gio_task_thread_result /home/elmarco/src/qemu/io/task.c:88
#12 0x7f60eef37317 in g_idle_dispatch ../glib/gmain.c:5552
#13 0x7f60eef3490b in g_main_dispatch ../glib/gmain.c:3182
#14 0x7f60eef357ac in g_main_context_dispatch ../glib/gmain.c:3847
#15 0x55ca90927231 in glib_pollfds_poll /home/elmarco/src/qemu/util/main-loop.c:214
#16 0x55ca90927420 in os_host_main_loop_wait /home/elmarco/src/qemu/util/main-loop.c:261
#17 0x55ca909275fa in main_loop_wait /home/elmarco/src/qemu/util/main-loop.c:515
#18 0x55ca8fc1c2a4 in main_loop /home/elmarco/src/qemu/vl.c:1942
#19 0x55ca8fc2eb3a in main /home/elmarco/src/qemu/vl.c:4724
#20 0x7f60e4082009 in __libc_start_main (/lib64/libc.so.6+0x21009)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20180306170959.3921-1-marcandre.lureau@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
In my "build everything" tree, a change to the types in
qapi-schema.json triggers a recompile of about 4800 out of 5100
objects.
The previous commit split up qmp-commands.h, qmp-event.h, qmp-visit.h,
qapi-types.h. Each of these headers still includes all its shards.
Reduce compile time by including just the shards we actually need.
To illustrate the benefits: adding a type to qapi/migration.json now
recompiles some 2300 instead of 4800 objects. The next commit will
improve it further.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-24-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
Let the callers take the object, then pass it to migrate_init().
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180208103132.28452-12-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We will not allow failures to happen when sending data from destination
to source via the return path. However it is possible that there can be
errors along the way. This patch allows the migrate_send_rp_message()
to return error when it happens, and further extended it to
migrate_send_rp_req_pages().
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180208103132.28452-9-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
If the postcopy down due to some reason, we can always see this on dst:
qemu-system-x86_64: RP: Received invalid message 0x0000 length 0x0000
However in most cases that's not the real issue. The problem is that
qemu_get_be16() has no way to show whether the returned data is valid or
not, and we are _always_ assuming it is valid. That's possibly not wise.
The best approach to solve this would be: refactoring QEMUFile interface
to allow the APIs to return error if there is. However it needs quite a
bit of work and testing. For now, let's explicitly check the validity
first before using the data in all places for qemu_get_*().
This patch tries to fix most of the cases I can see. Only if we are with
this, can we make sure we are processing the valid data, and also can we
make sure we can capture the channel down events correctly.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180208103132.28452-2-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The macro expansions of qdict_put_TYPE() and qlist_append_TYPE() need
qbool.h, qnull.h, qnum.h and qstring.h to compile. We include qnull.h
and qnum.h in the headers, but not qbool.h and qstring.h. Works,
because we include those wherever the macros get used.
Open-coding these helpers is of dubious value. Turn them into
functions and drop the includes from the headers.
This cleanup makes the number of objects depending on qapi/qmp/qnum.h
from 4551 (out of 4743) to 46 in my "build everything" tree. For
qapi/qmp/qnull.h, the number drops from 4552 to 21.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-10-armbru@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
In e91d895 I added the new pause-before-switchover mechanism
to allow migration completion to be delayed; this changes the
last state prior to completion to MIGRATE_STATUS_DEVICE rather
than MIGRATE_STATUS_ACTIVE.
Fix the failure path in migration_completion to recover the block
devices if it fails in MIGRATE_STATUS_DEVICE, not just the
MIGRATE_STATUS_ACTIVE that it previously had.
This corresponds to rh bz:
https://bugzilla.redhat.com/show_bug.cgi?id=1538494
whose symptom is an occasional source crash on a failed migration.
Fixes: e91d8951d5
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixes: b15df1ae50 ("migration: cleanup stats update into function")
The threshold size is changed to be recorded in s->threshold_size.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Allow whatever is performing the connection to pass migrate_fd_connect
an error to indicate there was a problem during connection, an allow
us to clean up.
The caller must free the error.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This reverts commits
ca6011c migration: add postcopy total blocktime into query-migrate
5f32dc8 migration: add blocktime calculation into migration-test
2f7dae9 migration: postcopy_blocktime documentation
3be98be migration: calculate vCPU blocktime on dst side
01a87f0 migration: add postcopy blocktime ctx into MigrationIncomingState
31bf06a migration: introduce postcopy-blocktime capability
as they don't build on ppc32 due to trying to do atomic accesses
on types that are larger than the host pointer type.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It is already called in migrate_fd_cleanup.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Keep the one in migrate_fd_cleanup() would be enough. Removing the other
two.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This patch only moved the last part of migration_thread() into a new
function migration_iteration_finish() to make it much shorter. With
previous works to remove some local variables, now it's fairly easy to
do that.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The major work for migration iterations are to move RAM/block/... data
via qemu_savevm_state_iterate(). Generalize those part into a single
function.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We have quite a few lines in migration_thread() that calculates some
statistics for the migration interations. Isolate it into a single
function to improve readability.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It converts the old if clauses into switch, explicitly mentions the
possible migration states. The old nested "if"s are not clear on what
we do on different states.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Generalize the calculation part when migration complete into a
function to simplify migration_thread().
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Introduce MigrationState.downtime_start to replace the local variable
"start_time" in migration_thread to avoid passing things around.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Firstly, it was passed around. Let's just move it into MigrationState
just like many other variables as state of migration, renaming it to
vm_was_running.
One thing to mention is that for postcopy, we actually don't need this
knowledge at all since postcopy can't resume a VM even if it fails (we
can see that from the old code too: when we try to resume we also check
against "entered_postcopy" variable). So further we do this:
- in postcopy_start(), we don't update vm_old_running since useless
- in migration_thread(), we don't need to check entered_postcopy when
resume, since it's only used for precopy.
Comment this out too for that variable definition.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It was used either to:
1. store initial timestamp of migration start, and
2. store total time used by last migration
Let's provide two parameters for each of them. Mix use of the two is
slightly misleading.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Moving existing callers all into migrate_fd_cleanup(). It simplifies
migration_thread() a bit.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
When reaching here if we are still "active" it means we must be in colo
state. After a quick discussion offlist, we decided to use the safer
error_report().
Finally I want to use "switch" here rather than lots of complicated if
clauses.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
current_migration has .instance_finalize callback, but it is not
called, because nobody unrefs current_migration. Fix that.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Postcopy total blocktime is available on destination side only.
But query-migrate was possible only for source. This patch
adds ability to call query-migrate on destination.
To be able to see postcopy blocktime, need to request postcopy-blocktime
capability.
The query-migrate command will show following sample result:
{"return":
"postcopy-vcpu-blocktime": [115, 100],
"status": "completed",
"postcopy-blocktime": 100
}}
postcopy_vcpu_blocktime contains list, where the first item is the first
vCPU in QEMU.
This patch has a drawback, it combines states of incoming and
outgoing migration. Ongoing migration state will overwrite incoming
state. Looks like better to separate query-migrate for incoming and
outgoing migration or add parameter to indicate type of migration.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alexey Perevalov <a.perevalov@samsung.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Right now it could be used on destination side to
enable vCPU blocktime calculation for postcopy live migration.
vCPU blocktime - it's time since vCPU thread was put into
interruptible sleep, till memory page was copied and thread awake.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alexey Perevalov <a.perevalov@samsung.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Once there, do one thing for line
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
We use int for everything (int64_t), and then we check that value is
between 0 and 255. Change it to the valid types.
This change only happens for HMP. QMP always use bytes and similar.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Right now it is a variable in MigrationState instead of a
MigrationParameter. The change allows to set it as the rest of the
Migration parameters, from the command line, with
query_migration_paramters, set_migrate_parameters, etc.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
After the previous commits, we make sure that the value passed is
right, or we just drop an error. So now we return if there is one
error or we have setup correctly the value passed.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
--
Improve error messasge
Return 0 always for success
We now report errors also when we finish migration, not only on info
migrate. We plan to use this error from several places, and we want
the first error to happen to win, so we add an mutex to order it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add pause-before-switchover support for postcopy.
After starting postcopy it will transition
active->pre-switchover->postcopy_active
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
If a migration_cancel is issued during the new paused state,
kick the pause_sem to get to unpause so it can cancel.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
A new qmp command allows the caller to continue from a given
paused state.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Wait for a semaphore before completing the migration,
if the previously added capability was enabled.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add two statuses for use when the 'pause-before-switchover'
capability is enabled.
'pre-switchover' is the state that we wait in for management
to allow us to continue.
'device' is the state we enter while serialising the devices
after management gives us the OK.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
When 'pause-before-switchover' is enabled, the outgoing migration
will pause before invalidating the block devices and serializing
the device state.
At this point the management layer gets the chance to clean up any
device jobs or other device users before the migration completes.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
That tiny refactoring is necessary to be able to set
UFFD_FEATURE_THREAD_ID while requesting features, and then
to create downtime context in case when kernel supports it.
Signed-off-by: Alexey Perevalov <a.perevalov@samsung.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Split common postcopy staff from ram postcopy staff.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We need that on later patches.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Creation of the threads, nothing inside yet.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
--
Use pointers instead of long array names
Move to use semaphores instead of conditions as paolo suggestion
Put all the state inside one struct.
Use a counter for the number of threads created. Needed during cancellation.
Add error return to thread creation
Add id field
Rename functions to multifd_save/load_setup/cleanup
Change recv parameters to a pointer to struct
Change back to a struct
Use Error * for _cleanup
Indicates how many pages we are going to send in each batch to a multifd
thread.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
--
Be consistent with defaults and documentation
Use new DEFINE_PROP_*
Rename x-multifd-group to x-multifd-page-count
Indicates the number of channels that we will create. By default we
create 2 channels.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
--
Catch inconsistent defaults (eric).
Improve comment stating that number of threads is the same than number
of sockets
Use new DEFIN_PROP_*
Rename x-multifd-threads to x-multifd-threads
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
--
Use new DEFINE_PROP
This function allows us to decide when to close the listener socket.
For now, we only need one connection.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
We pass the ioc instead of the fd. This will allow us to have more
than one channel open. We also make sure that we set the
from_src_file sooner, so we don't need to pass it as a parameter.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
--
Do not assing mis->from_src_file (peterxu)
Strings are more readable for debugging.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1504081950-2528-5-git-send-email-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixed up merge with 977c73
migration_incoming_state_destroy doesn't really destroy, it cleans up.
After a loadvm it's called, but the loadvm command can be run twice,
and so destroying an init-once mutex breaks on the second loadvm.
Reported-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170825141940.20740-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The next commit will put it to use. May look pointless now, but we're
going to change the FOO_lookup's type, and then it'll help.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-13-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Spotted thanks to valgrind and tests/device-introspect-test:
==11711== 1 bytes in 1 blocks are definitely lost in loss record 6 of 14,537
==11711== at 0x4C2EB6B: malloc (vg_replace_malloc.c:299)
==11711== by 0x1E0CDBD8: g_malloc (gmem.c:94)
==11711== by 0x1E0E696E: g_strdup (gstrfuncs.c:363)
==11711== by 0x695693: migration_instance_init (migration.c:2226)
==11711== by 0x717C4B: object_init_with_type (object.c:344)
==11711== by 0x717E80: object_initialize_with_type (object.c:375)
==11711== by 0x7182EB: object_new_with_type (object.c:483)
==11711== by 0x718328: object_new (object.c:493)
==11711== by 0x4B8A29: qmp_device_list_properties (qmp.c:542)
==11711== by 0x4A9561: qmp_marshal_device_list_properties (qmp-marshal.c:1425)
==11711== by 0x819D4A: do_qmp_dispatch (qmp-dispatch.c:104)
==11711== by 0x819E82: qmp_dispatch (qmp-dispatch.c:131)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170801160419.14180-1-marcandre.lureau@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
migrate-set-parameters sets migration parameters according to is
arguments like this:
* Present means "set the parameter to this value"
* Absent means "leave the parameter unchanged"
* Except for parameters tls_creds and tls_hostname, "" means "reset
the parameter to its default value
The first two are perfectly normal: presence of the parameter makes
the command do something.
The third one overloads the parameter with a second meaning. The
overloading is *implicit*, i.e. it's not visible in the types. Works
here, because "" is neither a valid TLS credentials ID, nor a valid
host name.
Pressing argument values the schema accepts, but are semantically
invalid, into service to mean "reset to default" is not general, as
suitable invalid values need not exist. I also find it ugly.
To clean this up, we could add a separate flag argument to ask for
"reset to default", or add a distinct value to @tls_creds and
@tls_hostname. This commit implements the latter: add JSON null to
the values of @tls_creds and @tls_hostname, deprecate "".
Because we're so close to the 2.10 freeze, implement it in the
stupidest way possible: have qmp_migrate_set_parameters() rewrite null
to "" before anything else can see the null. The proper way to do it
would be rewriting "" to null, but that requires fixing up code to
work with null. Add TODO comments for that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Commit de63ab6 "migrate: Share common MigrationParameters struct"
reused MigrationParameters for the arguments of
migrate-set-parameters, with the following rationale:
It is rather verbose, and slightly error-prone, to repeat
the same set of parameters for input (migrate-set-parameters)
as for output (query-migrate-parameters), where the only
difference is whether the members are optional. We can just
document that the optional members will always be present
on output, and then share a common struct between both
commands. The next patch can then reduce the amount of
code needed on input.
I need to unshare them to correct a design flaw in a stupid, but
minimally invasive way, in the next commit. We can restore the
sharing when we redo that patch in a less stupid way. Add a suitable
TODO comment.
Note that I revert only the sharing part of commit de63ab6, not the
part that made the members of query-migrate-parameters' result
optional. The schema (and thus introspection) remains inaccurate for
query-migrate-parameters. If we decide not to restore the sharing, we
should revert that part, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
qmp_query_migrate_parameters() and qmp_migrate_set_parameters()
effectively duplicate QAPI_CLONE() inline. Add suitable TODO
comments.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Optional MigrationParameters members tls_creds and tls_hostname can't
actually be absent outside qmp_migrate_set_parameters() since commit
4af245d (v2.9.0).
Note that commit 4af245d reverted the part of commit de63ab6 (v2.8.0)
that made tls_creds and tls_hostname absent instead of "" in the value
of query-migrate-parameters, even though commit de63ab6 called that a
mistake. What a mess.
Drop the redundant tests for presence, and update documentation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Checks validity for all the capabilities that we enabled with command
line.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1500349150-13240-11-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Abstracted from migrate_set_block_enabled() to allocate
MigrationCapabilityStatusList properly.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1500349150-13240-10-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Abstract helper function to check migration capabilities (from the old
qmp_migrate_set_capabilities). Prepare to be used somewhere else.
There is side effect on the change: when applying the capabilities, we
were skipping the invalid ones, but still applying the valid ones (if
they are provided in the same QMP request). After this refactoring,
we'll ignore all the capabilities if we detected invalid setup along the
way. However, I don't think it is a problem since general users should
not provide anything invalid after all.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1500349150-13240-9-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Since commit a15215f3 ("build: remove --enable-colo/--disable-colo"),
colo is always supported. We don't need any colo_supported() now since
it is always true. Removing any extra code that depends on it.
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Hailiang Zhang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Zhang Chen<zhangchen.fnst@cn.fujitsu.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1500349150-13240-8-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Adding validity check for the migration parameters passed in via global
properties.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1500349150-13240-7-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Abstracted from qmp_migrate_set_parameters().
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1500349150-13240-6-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Helper to check the parameters. Abstracted from
qmp_migrate_set_parameters().
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1500349150-13240-5-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Do the same thing to migration capabilities, just like what we did in
previous patch for migration parameters.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1500349150-13240-4-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Export migration parameters to qdev properties. Then we can use, for
example:
-global migration.x-cpu-throttle-initial=xxx
To specify migration parameters during init.
Prefix "x-" is appended for each parameter exported to show that this is
not a stable interface, and only for debugging/testing purpose.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1500349150-13240-3-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Closing the file before exit on a failure allows
the source to cleanup better, especially with RDMA.
Partial fix for https://bugs.launchpad.net/qemu/+bug/1545052
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170717110936.23314-3-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Once there, be consistent and use
compress_thread_{save,load}_{setup,cleanup}.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170628095228.4661-6-quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Once there, I rename ram_migration_cleanup() to ram_save_cleanup().
Notice that this is the first pass, and I only passed XBZRLE to the
new scheme. Moved decoded_buf to inside XBZRLE struct.
As a bonus, I don't have to export xbzrle functions from ram.c.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
--
loaded_data pointer was needed because called can change it (dave)
spell loaded correctly in comment (dave)
Message-Id: <20170628095228.4661-5-quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We are going to use it now for more than save live regions.
Once there rename qemu_savevm_state_begin() to qemu_savevm_state_setup().
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170628095228.4661-2-quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
[Peter collected Eduardo's patch comment and formatted into patch]
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1499242883-2184-5-git-send-email-peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
MigrateState object is not ready at that time, so we'll get an
assertion. Use qemu_global_option() instead.
Reported-by: Eduardo Habkost <ehabkost@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Fixes: 3df663e ("migration: move only_migratable to MigrationState")
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1499242883-2184-2-git-send-email-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
When this capability is enabled, QEMU will use the return path even for
precopy migration. This is helpful at least in one case when destination
failed to load the image while source quited without confirmation. With
return path, source will wait for the last response from destination,
and if destination fails, it'll fail the migration on source, then the
guest can be run again on the source (rather than assuming to be good,
then the guest will be lost after source quits).
It needs to be enabled explicitly on source, otherwise disabled.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498472935-14461-1-git-send-email-peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It'll be strange that the migration object inherits TYPE_DEVICE. Add
some explanations to it.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498634144-26508-1-git-send-email-peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Now we have some globals that can be configured for migration. Dump them
in HMP info migration for better debugging.
(we can also use this to monitor whether COMPAT fields are applied
correctly on compatible machines)
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498536619-14548-11-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
These two parameters:
- MachineState::enforce_config_section
- MigrationState::send_configuration
are playing similar role here. This patch merges the first one into
second, then we'll have a single place to reference whether we need to
send the configuration section.
I didn't remove the MachineState.enforce_config_section field since when
applying that machine property (in machine_set_property()) we haven't
yet initialized global properties and migration object. Then, it's
still not easy to pass that boolean to MigrationState at such an early
time.
A natural benefit for current patch is that now we kept the meaning of
"enforce-config-section" since it'll still have the highest
priority (that's what "enforce" mean I guess).
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498536619-14548-10-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Move it into MigrationState, revert its meaning and renaming it to
send_section_footer, with a property bound to it. Same trick is played
like previous patches.
Removing savevm_skip_section_footers().
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498536619-14548-9-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It was in SaveState but now moved to MigrationState altogether, reverted
its meaning, then renamed to "send_configuration". Again, using
HW_COMPAT_2_3 for old PC/SPAPR machines, and accel_register_prop() for
xen_init().
Removing savevm_skip_configuration().
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498536619-14548-8-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
One less global variable, and it does only matter with migration.
We keep the old "--only-migratable" option, but also now we support:
-global migration.only-migratable=true
Currently still keep the old interface.
Hmm, now vl.c has no way to access migrate_get_current(). Export a
function for it to setup only_migratable.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498536619-14548-7-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Put it into MigrationState then we can use the properties to specify
whether to enable storing global state.
Removing global_state_set_optional() since now we can use HW_COMPAT_2_3
for x86/power, and AccelClass.global_props for Xen.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498536619-14548-6-git-send-email-peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Let the old man "MigrationState" join the object family. Direct benefit
is that we can start to use all the property features derived from
current QDev, like: HW_COMPAT_* bits, command line setup for migration
parameters (so will never need to set them up each time using HMP/QMP,
this is really, really attractive for test writters), etc.
I see no reason to disallow this happen yet. So let's start from this
one, to see whether it would be anything good.
Now we init the MigrationState struct statically in main() to make sure
it's initialized after global properties are applied, since we'll use
them during creation of the object.
No functional change at all.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1498536619-14548-5-git-send-email-peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Previously, dst side will immediately try to lock the write byte upon
receiving QEMU_VM_EOF, but at src side, bdrv_inactivate_all() is only
done after sending it. If the src host is under load, dst may fail to
acquire the lock due to racing with the src unlocking it.
Fix this by hoisting the bdrv_inactivate_all() operation before
QEMU_VM_EOF.
N.B. A further improvement could possibly be done to cleanly handover
locks between src and dst, so that there is no window where a third QEMU
could steal the locks and prevent src and dst from running.
N.B. This commit includes a minor improvement to the error handling
by using qemu_file_set_error().
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 20170616160658.32290-1-famz@redhat.com
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
[PMM: noted qemu_file_set_error() use in commit as suggested by Daniel]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
0425dc9 is actually v1 of that patch, but it was accidentally
merged (while there was a v2). That will cause problem when we try to
migrate to some old QEMUs when return path is not really there. Let's
fix it, then squashing this patch with 0425dc9 will be exactly patch
content of v2.
Fixes: 0425dc9 ("migration: isolate return path on src")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Nothing uses it outside of migration.h
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
It don't belong anywhere else, just the global state where everybody
can stick other things.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
So, move them there. Notice that we export functions that send
commands, not the command themselves.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Merge them.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Once there, create populate_disk_info.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
--
- create populate_disk_info instead of "abusing" populate_ram_info
Assigning directly to *errp is not valid, as errp may be NULL,
&error_fatal, or &error_abort. Use error_propagate() instead.
Cc: Juan Quintela <quintela@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
There are some places that binded "return path" with postcopy. Let's be
prepared for its usage even without postcopy. This patch mainly did this
on source side.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Block migration may still access the image during its
.save_live_complete_precopy() implementation, so we should only
inactivate the image afterwards.
Another reason for the change is that inactivating an image fails when
there is still a non-device BlockBackend using it, which includes the
BBs used by block migration. We want to give block migration a chance to
release the BBs before trying to inactivate the image (this will be done
in another patch).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
RAM Statistics need to survive migration to make info migrate work, so we
need to store them outside of RAMState. As we already have an struct
with those fields, just used them. (MigrationStats and XBZRLECacheStats).
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
We shouldn't be using memory later than that.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
All functions were internal, except blk_mig_init() that is exported in
misc.h now.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
All functions are internal except for ram_mig_init(). Create
migration/misc.h for this kind of functions.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Just for the functions exported from tls.c. Notice that we can't
remove the migration/migration.h include from tls.c because it access
directly MigrationState for the tls params.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Split the file into public and internal interfaces. I have to rename
the external one because we can't have two include files with the same
name in the same directory. Build system gets confused. The only
exported functions are the ones that handle basic types.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We were do the shutting off only for postcopy. Now we do this as long as
the source return path is there.
Moving the cleanup of from_src_file there too.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The return path channel is possibly leaked. Fix it.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
So we remove all traces of them.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This removes last trace of migration functions from sysemu/sysemu.h.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
That is the only function that we need from exec.c, and having to
include the whole sysemu.h for this.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
---
/me leans to be less sloppy with copyright notices
thanks Dave
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
---
Minor rearrangements due to rebase
Create an include for its exported functions.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
---
Add proper header
Many users now prefer to use drive_mirror over NBD as an
alternative to the older migrate -b option; drive_mirror is
more complex to setup but gives you more options (e.g. only
migrating some of the disks if some of them are shared).
Allow the large chunk of block migration code to be compiled
out for those who don't use it.
Based on a downstream-patch we've had for a while by Jeff Cody.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
--
- When compiled out, allow seting block only with false value (eric)
Not used anymore after moving block migration to use capabilities.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
We have change in the previous patch to use migration capabilities for
it. Notice that we continue using the old command line flags from
migrate command from the time being. Remove the set_params method as
now it is empty.
For savevm, one can't do a:
savevm -b/-i foo
but now one can do:
migrate_set_capability block on
savevm foo
And we can't use block migration. We could disable block capability
unconditionally, but it would not be much better.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
---
- Maintain shared/enabled dependency (Xu suggestion)
- Now we maintain the dependency on the setter functions
- improve error messages
Create one capability for block migration and one parameter for
incremental block migration.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
---
- address all Markus comments
- use Markus and Eric text descriptions
- change logic another time
- improve text messages
The function is only used once, and nothing else in migration knows
about objects. Create the function vmstate_device_is_migratable() in
savem.c that really do the bit that is related with migration.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Yes, we don't have a good place to put that stuff.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This allows us to remove lots of includes of migration/migration.h
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Instead of manually calling blk_resume_after_migration() in migration
code after doing bdrv_invalidate_cache_all(), integrate the BlockBackend
activation with cache invalidation into a single function. This is
achieved with a new callback in BdrvChildRole that is called by
bdrv_invalidate_cache_all().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Migration code activates all block driver nodes on the destination when
the migration completes. It does so by calling
bdrv_invalidate_cache_all() and blk_resume_after_migration(). There is
one code path for precopy and one for postcopy migration, resulting in
four function calls, which used to have three different failure modes.
This patch unifies the behaviour so that failure to activate all block
nodes is non-fatal, but the error message is logged and the VM isn't
automatically started. 'cont' will retry activating the block nodes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
It is internal to migration, not intended for other users.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
In migration codes (especially in migration_thread()), max_size is used
in many place for the threshold value that we will start to do the final
flush and jump to the next stage to dump the whole rest things to
destination. However its name is confusing to first readers. Let's
rename it to "threshold_size" when proper and add a comment for it. No
functional change is made.
CC: Juan Quintela <quintela@redhat.com>
CC: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We set it right above this one. No need to set it twice.
CC: Juan Quintela <quintela@redhat.com>
CC: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
If we close the QEMUFile descriptor in process_incoming_migration_co()
while it has been stopped by an error, the postcopy_ram_listen_thread()
can try to continue to use it. And as the memory has been freed
it is working with an invalid pointer and crashes.
Fix this by releasing the memory after having managed the error
case (which, in fact, calls exit())
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit@kernel.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Only user don't have a MigrationState handly.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The number of dirty pages is output in 'pages' in the command
'info migrate', so add page-size to calculate the number of dirty
pages in bytes.
Signed-off-by: Chao Fan <fanc.fnst@cn.fujitsu.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It was used as a size in all cases except one.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We need to call for the migrate_get_current() in more that half of the
uses, so call that inside.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Treat it like the rest of ram stats counters. Export its value the
same way. As an added bonus, no more MigrationState used in
migration_bitmap_sync();
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
--
Again, dave was the one reviewing it
It can be recalculated from dirty_pages_rate.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
--
Dave was the one that reviewed it O:-)
This is a ram field that was inside MigrationState. Move it to
RAMState and make it the same that the other ram stats.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
This are the last postcopy fields still at MigrationState. Once there
Move MigrationSrcPageRequest to ram.c and remove MigrationState
parameters where appropiate.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
It was on MigrationState when it is only used inside ram.c for
postcopy. Problem is that we need to access it without being able to
pass it RAMState directly.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Its value can be calculated by other exported.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
For compatibility, we need to still send a value, but just specify it
and comment the fact.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
It reflects better what it does.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Usually guest devices don't like other writers to the same image, so
they use blk_set_perm() to prevent this from happening. In the migration
phase before the VM is actually running, though, they don't have a
problem with writes to the image. On the other hand, storage migration
needs to be able to write to the image in this phase, so the restrictive
blk_set_perm() call of qdev devices breaks it.
This patch flags all BlockBackends with a qdev device as
blk->disable_perm during incoming migration, which means that the
requested permissions are stored in the BlockBackend, but not actually
applied to its root node yet.
Once migration has finished and the VM should be resumed, the
permissions are applied. If they cannot be applied (e.g. because the NBD
server used for block migration hasn't been shut down), resuming the VM
fails.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Kashyap Chamarthy <kchamart@redhat.com>
The tls-creds parameter has a default value of NULL indicating
that TLS should not be used. Setting it to non-NULL enables
use of TLS. Once tls-creds are set to a non-NULL value via the
monitor, it isn't possible to set them back to NULL again, due
to current implementation limitations. The empty string is not
a valid QObject identifier, so this switches to use "" as the
default, indicating that TLS will not be used
The tls-hostname parameter has a default value of NULL indicating
the the hostname from the migrate connection URI should be used.
Again, once tls-hostname is set non-NULL, to override the default
hostname for x509 cert validation, it isn't possible to reset it
back to NULL via the monitor. The empty string is not a valid
hostname, so this switches to use "" as the default, indicating
that the migrate URI hostname should be used.
Using "" as the default for both, also means that the monitor
commands "info migrate_parameters" / "query-migrate-parameters"
will report existance of tls-creds/tls-parameters even when set
to their default values.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Record the largest page size in use; we'll need it soon for allocating
temporary buffers.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20170224182844.32452-7-dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Commit a3a3d8c7 introduced a segfault bug while checking for
'dc->vmsd->unmigratable' which caused QEMU to crash when trying to add
devices which do no set their 'dc->vmsd' yet while initialization.
Place a 'dc->vmsd' check prior to it so that we do not segfault for
such devices.
NOTE: This doesn't compromise the functioning of --only-migratable
option as all the unmigratable devices do set their 'dc->vmsd'.
Introduce a new function check_migratable() and move the
only_migratable check inside it, also use stubs to avoid user-mode qemu
build failures.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1487009088-23891-1-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Using QMP, the error message of 'migrate_set_downtime' was displaying
the values in milliseconds, being misleading with the command that
accepts the value in seconds:
{ "execute": "migrate_set_downtime", "arguments": {"value": 3000}}
{"error": {"class": "GenericError", "desc": "Parameter 'downtime_limit'
expects an integer in the range of 0 to 2000000 milliseconds"}}
This message is also seen in HMP when trying to set the same
parameter:
(qemu) migrate_set_parameter downtime-limit 3000000
Parameter 'downtime_limit' expects an integer in the range of 0 to
2000000 milliseconds
To allow for a proper error message when using QMP, a validation
of the user input was added in 'qmp_migrate_set_downtime'.
Signed-off-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Message-Id: <20170222151729.5812-1-danielhb@linux.vnet.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
If we set checkpoint-delay through command 'migrate-set-parameters',
It will not take effect until we finish last sleep chekpoint-delay,
That's will be offensive espeically when we want to change its value
from an extreme big one to a proper value.
Fix it by using timer to realize checkpoint-delay.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Message-Id: <1484657864-21708-2-git-send-email-zhang.zhanghailiang@huawei.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
After the start of postcopy migration there are some non-dirty pages which have
already been migrated. These pages are no longer needed on the source vm so that
we can free them and it doen't hurt to complete the migration.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Message-Id: <20170203152321.19739-4-pbutsykin@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This feature frees the migrated memory on the source during postcopy-ram
migration. In the second step of postcopy-ram migration when the source vm
is put on pause we can free unnecessary memory. It will allow, in particular,
to start relaxing the memory stress on the source host in a load-balancing
scenario.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Message-Id: <20170203152321.19739-3-pbutsykin@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Manually merged in Pavel's 'migration: madvise error_report fixup!'
An early postcopy failure can be recovered from as long as we know
we haven't sent the command to run the destination.
We have to undo the bdrv_inactivate_all by calling
bdrv_invalidate_cache_all
Note that I'm not using ms->block_inactive because once we've
sent the postcopy package we dont want anything else to try
and recover the block storage on the source; the destination
might have started writing to it.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170202155909.31784-3-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1485207141-1941-3-git-send-email-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Change the name of live migration thread from 'migration'
to 'live_migration' to identify it clearly. 'migration'
is a generic word and kernel also has tasks for process
migration with the name 'migration/cpu#'.
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Message-Id: <1485178976-15225-1-git-send-email-pagupta@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
commit fe904ea824 fixed a case
which migration aborted QEMU because it didn't regain the control
of images while some errors happened.
Actually, there are another two cases can trigger the same error reports:
" bdrv_co_do_pwritev: Assertion `!(bs->open_flags & 0x0800)' failed",
Case 1, codes path:
migration_thread()
migration_completion()
bdrv_inactivate_all() ----------------> inactivate images
qemu_savevm_state_complete_precopy()
socket_writev_buffer() --------> error because destination fails
qemu_fflush() ----------------> set error on migration stream
-> qmp_migrate_cancel() ----------------> user cancelled migration concurrently
-> migrate_set_state() ------------------> set migrate CANCELLIN
migration_completion() -----------------> go on to fail_invalidate
if (s->state == MIGRATION_STATUS_ACTIVE) -> Jump this branch
Case 2, codes path:
migration_thread()
migration_completion()
bdrv_inactivate_all() ----------------> inactivate images
migreation_completion() finished
-> qmp_migrate_cancel() ---------------> user cancelled migration concurrently
qemu_mutex_lock_iothread();
qemu_bh_schedule (s->cleanup_bh);
As we can see from above, qmp_migrate_cancel can slip in whenever
migration_thread does not hold the global lock. If this happens after
bdrv_inactive_all() been called, the above error reports will appear.
To prevent this, we can call bdrv_invalidate_cache_all() in qmp_migrate_cancel()
directly if we find images become inactive.
Besides, bdrv_invalidate_cache_all() in migration_completion() doesn't have the
protection of big lock, fix it by add the missing qemu_mutex_lock_iothread();
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Message-Id: <1485244792-11248-1-git-send-email-zhang.zhanghailiang@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
migrate_add_blocker should rightly fail if the '--only-migratable'
option was specified and the device in use should not be able to
perform the action which results in an unmigratable VM.
Make migrate_add_blocker return -EACCES in this case.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-6-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
If a migration is already in progress and somebody attempts
to add a migration blocker, this should rightly fail.
Add an errp parameter and a retcode return value to migrate_add_blocker.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-5-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Merged with recent 'Allow invtsc migration' change
We forgot to assign true to params->has_x_checkpoint_delay parameter
in qmp_query_migrate_parameters.
Without this, qmp command 'query-migrate-parameters' doesn't show the
default value for x-checkpoint-delay option.
This also fixes the fact that HMP was relying on unspecified behavior by
reading x_checkpoint_delay without checking has_x_checkpoint_delay.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sur7
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/amit-migration/tags/migration-for-2.8' into staging
Migration bits from the COLO project
# gpg: Signature made Sun 30 Oct 2016 10:39:55 GMT
# gpg: using RSA key 0xEB0B4DFC657EF670
# gpg: Good signature from "Amit Shah <amit@amitshah.net>"
# gpg: aka "Amit Shah <amit@kernel.org>"
# gpg: aka "Amit Shah <amitshah@gmx.net>"
# Primary key fingerprint: 48CA 3722 5FE7 F4A8 B337 2735 1E9A 3B5F 8540 83B6
# Subkey fingerprint: CC63 D332 AB8F 4617 4529 6534 EB0B 4DFC 657E F670
* remotes/amit-migration/tags/migration-for-2.8:
MAINTAINERS: Add maintainer for COLO framework related files
configure: Support enable/disable COLO feature
docs: Add documentation for COLO feature
COLO: Implement failover work for secondary VM
COLO: Implement the process of failover for primary VM
COLO: Introduce state to record failover process
COLO: Add 'x-colo-lost-heartbeat' command to trigger failover
COLO: Synchronize PVM's state to SVM periodically
COLO: Add checkpoint-delay parameter for migrate-set-parameters
COLO: Load VMState into QIOChannelBuffer before restore it
COLO: Send PVM state to secondary side when do checkpoint
COLO: Add a new RunState RUN_STATE_COLO
COLO: Introduce checkpointing protocol
COLO: Establish a new communicating path for COLO
migration: Switch to COLO process after finishing loadvm
migration: Enter into COLO mode after migration if COLO is enabled
COLO: migrate COLO related info to secondary node
migration: Introduce capability 'x-colo' to migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add checkpoint-delay parameter for migrate-set-parameters, so that
we can control the checkpoint frequency when COLO is in periodic mode.
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
Switch from normal migration loadvm process into COLO checkpoint process if
COLO mode is enabled.
We add three new members to struct MigrationIncomingState,
'have_colo_incoming_thread' and 'colo_incoming_thread' record the COLO
related thread for secondary VM, 'migration_incoming_co' records the
original migration incoming coroutine.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
Add a new migration state: MIGRATION_STATUS_COLO. Migration source side
enters this state after the first live migration successfully finished
if COLO is enabled by command 'migrate_set_capability x-colo on'.
We reuse migration thread, so the process of checkpointing will be handled
in migration thread.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
We add helper function colo_supported() to indicate whether
colo is supported or not, with which we use to control whether or not
showing 'x-colo' string to users, they can use qmp command
'query-migrate-capabilities' or hmp command 'info migrate_capabilities'
to learn if colo is supported.
The default value for COLO (COarse-Grain LOck Stepping) is disabled.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
All the callers of migrate_fd_error() pass a non-NULL
error parameter, and if any did pass NULL then we would
segfault in error_copy(), so remove the unnecessary
NULL check earlier in the function.
(Spotted by Coverity.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Ensure that all I/O channels created for migration are given names
to distinguish their respective roles.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Mark the old commands 'migrate_set_speed' and 'migrate_set_downtime' as
deprecated.
Move max-bandwidth and downtime-limit into migrate-set-parameters for
setting maximum migration speed and expected downtime limit parameters
respectively.
Change downtime units to milliseconds (only for new-command) and set
its upper bound limit to 2000 seconds.
Update the query part in both hmp and qmp qemu control interfaces.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This patch fixes the out-of-bounds check of migration parameters in
qmp_migrate_set_parameters() for cpu-throttle-initial and
cpu-throttle-increment by adding a return statement for both as they
were broken since their introduction in 2.5 via commit 1626fee.
Due to the missing return statements, parameters were getting set to
out-of-bounds values despite the error.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Now that QAPI makes it easy to pass a struct around, we don't
have to declare as many parameters or local variables.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It is rather verbose, and slightly error-prone, to repeat
the same set of parameters for input (migrate-set-parameters)
as for output (query-migrate-parameters), where the only
difference is whether the members are optional. We can just
document that the optional members will always be present
on output, and then share a common struct between both
commands. The next patch can then reduce the amount of
code needed on input.
Also, we made a mistake in qemu 2.7 of returning an empty
string during 'query-migrate-parameters' when there is no
TLS, rather than omitting TLS details entirely. Technically,
this change risks breaking any 2.7 client that is hard-coded
to expect the parameter's existence; on the other hand, clients
that are portable to 2.6 already must be prepared for those
members to not be present.
And this gets rid of yet one more place where the QMP output
visitor is silently converting a NULL string into "" (which
is a hack I ultimately want to kill off).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
If a migration fails/is cancelled during the postcopy stage we currently
end up with the runstate as finish-migrate, where it should be post-migrate.
There's a small window in precopy where I think the same thing can
happen, but I've never seen it.
It rarely matters; the only postcopy case is if you restart a migration, which
again is a case that rarely matters in postcopy because it's only
safe to restart the migration if you know the destination hasn't
been running (which you might if you started the destination with -S
and hadn't got around to 'c' ing it before the postcopy failed).
Even then it's a small window but potentially you could hit if
there's a problem loading the devices on the destination.
This corresponds to:
https://bugzilla.redhat.com/show_bug.cgi?id=1355683
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Message-Id: <1468601086-32117-1-git-send-email-dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
In practice the entry argument is always known at creation time, and
it is confusing that sometimes qemu_coroutine_enter is used with a
non-NULL argument to re-enter a coroutine (this happens in
block/sheepdog.c and tests/test-coroutine.c). So pass the opaque value
at creation time, for consistency with e.g. aio_bh_new.
Mostly done with the following semantic patch:
@ entry1 @
expression entry, arg, co;
@@
- co = qemu_coroutine_create(entry);
+ co = qemu_coroutine_create(entry, arg);
...
- qemu_coroutine_enter(co, arg);
+ qemu_coroutine_enter(co);
@ entry2 @
expression entry, arg;
identifier co;
@@
- Coroutine *co = qemu_coroutine_create(entry);
+ Coroutine *co = qemu_coroutine_create(entry, arg);
...
- qemu_coroutine_enter(co, arg);
+ qemu_coroutine_enter(co);
@ entry3 @
expression entry, arg;
@@
- qemu_coroutine_enter(qemu_coroutine_create(entry), arg);
+ qemu_coroutine_enter(qemu_coroutine_create(entry, arg));
@ reentry @
expression co;
@@
- qemu_coroutine_enter(co, NULL);
+ qemu_coroutine_enter(co);
except for the aforementioned few places where the semantic patch
stumbled (as expected) and for test_co_queue, which would otherwise
produce an uninitialized variable warning.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The *_to_cpup() and cpu_to_*w() functions just compose a pointer
dereference with a byteswap. Instead use ld*_p() and st*_p(),
which handle potential pointer misalignment and avoid the need
to cast the pointer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Message-Id: <1465574962-2710-1-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Apply the following renames for starting incoming migration:
process_incoming_migration -> migration_fd_process_incoming
migration_set_incoming_channel -> migration_channel_process_incoming
migration_tls_set_incoming_channel -> migration_tls_channel_process_incoming
and for starting outgoing migration:
migration_set_outgoing_channel -> migration_channel_connect
migration_tls_set_outgoing_channel -> migration_tls_channel_connect
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1464776234-9910-3-git-send-email-berrange@redhat.com
Message-Id: <1464776234-9910-3-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Knowing whether the destination host supports migration with
postcopy can be tricky.
The destination doesn't need the capability set, however
if we set it then use the opportunity to do the test and
tell the user/management layer early.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1465816605-29488-7-git-send-email-dgilbert@redhat.com
Message-Id: <1465816605-29488-7-git-send-email-dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
On the source, add a count of page requests received from the
destination.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Message-id: 1465816605-29488-4-git-send-email-dgilbert@redhat.com
Message-Id: <1465816605-29488-4-git-send-email-dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The RAM section of qmp_query_migrate is reasonably complex
and repeated 3 times. Split it out into a helper.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1465816605-29488-3-git-send-email-dgilbert@redhat.com
Reviwed-by: Denis V. Lunev <den@openvz.org>
Message-Id: <1465816605-29488-3-git-send-email-dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
This extends the migration_set_incoming_channel and
migration_set_outgoing_channel methods so that they
will automatically wrap the QIOChannel in a
QIOChannelTLS instance if TLS credentials are configured
in the migration parameters.
This allows TLS to work for tcp, unix, fd and exec
migration protocols. It does not (currently) work for
RDMA since it does not use these APIs, but it is
unlikely that TLS would be desired with RDMA anyway
since it would degrade the performance to that seen
with TCP defeating the purpose of using RDMA.
On the target host, QEMU would be launched with a set
of TLS credentials for a server endpoint
$ qemu-system-x86_64 -monitor stdio -incoming defer \
-object tls-creds-x509,dir=/home/berrange/security/qemutls,endpoint=server,id=tls0 \
...other args...
To enable incoming TLS migration 2 monitor commands are
then used
(qemu) migrate_set_str_parameter tls-creds tls0
(qemu) migrate_incoming tcp:myhostname:9000
On the source host, QEMU is launched in a similar
manner but using client endpoint credentials
$ qemu-system-x86_64 -monitor stdio \
-object tls-creds-x509,dir=/home/berrange/security/qemutls,endpoint=client,id=tls0 \
...other args...
To enable outgoing TLS migration 2 monitor commands are
then used
(qemu) migrate_set_str_parameter tls-creds tls0
(qemu) migrate tcp:otherhostname:9000
Thanks to earlier improvements to error reporting,
TLS errors can be seen 'info migrate' when doing a
detached migration. For example:
(qemu) info migrate
capabilities: xbzrle: off rdma-pin-all: off auto-converge: off zero-blocks: off compress: off events: off x-postcopy-ram: off
Migration status: failed
total time: 0 milliseconds
error description: TLS handshake failed: The TLS connection was non-properly terminated.
Or
(qemu) info migrate
capabilities: xbzrle: off rdma-pin-all: off auto-converge: off zero-blocks: off compress: off events: off x-postcopy-ram: off
Migration status: failed
total time: 0 milliseconds
error description: Certificate does not match the hostname localhost
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-27-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Define two new migration parameters to be used with TLS encryption.
The 'tls-creds' parameter provides the ID of an instance of the
'tls-creds' object type, or rather a subclass such as 'tls-creds-x509'.
Providing these credentials will enable use of TLS on the migration
data stream.
If using x509 certificates, together with a migration URI that does
not include a hostname, the 'tls-hostname' parameter provides the
hostname to use when verifying the server's x509 certificate. This
allows TLS to be used in combination with fd: and exec: protocols
where a TCP connection is established by a 3rd party outside of
QEMU.
NB, this requires changing the migrate_set_parameter method in the
HMP to accept a 's' (string) value instead of 'i' (integer). This
is backwards compatible, because the parsing of strings allows the
quotes to be optional, thus any integer is also a valid string.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-26-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>