Implement the wakeup callback in the OHCI USBPortOps, so that when
a downstream device wakes up it correctly causes the OHCI controller
to come out of suspend.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
HcPeriodCurrentED is read-only, but Linux writes to it anyway; silently
ignore this rather than printing a warning message.
(Specifically, drivers/usb/host/ohci-hub.c:ohci_rh_resume() writes a
0, in at least kernels 2.6.25 through 2.6.39.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This causes an "Error: tried to detach unattached usb device " to be printed,
this can happen when deleting ie a usb host qdev, which did not
get attached (because a device matching the filter never got plugged in).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch fixes a bunch of issues in the itd descriptor handling.
Most important fix is to handle transfers which cross page borders
correctly by looking up the address of the next page. Luckily the
linux uses physically contigous memory so the data used to hits the
correct location even with this bug instead of corrupting guest
memory. Also the transfer length updates for outgoing transfers wasn't
correct.
While being at it DPRINTFs have been replaced by tracepoints.
The isoch_pause logic has been disabled. Not clear to me which propose
this serves and I think it is incorrect too as we just skip processing
itds. Even when no xfer happens we have to clear the active bit.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The USB tablet advertises that it supports the "boot" protocol.
However, its reports aren't "boot" protocol compatible. So, it
shouldn't claim that.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The QEMU USB mouse claims to support the "boot" protocol
(bInterfaceSubClass is 1). However, the mouse rejects the
Set_Protocol command.
The qemu mouse does support the "boot" protocol specification, so a
simple fix is to enable the Set_Protocol request.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The state machine doesn't stop in EXECUTING state any more when async
packets are in flight, so the checks are not needed any more and can
be dropped.
Also kick out the check for the frame timer. As we don't stop & sleep
any more on async packets this is obsolete.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds USBBusOps struct with (for now) only a single callback
which is called when a device is about to be destroyed. The USB Host
adapters are implementing this callback and use it to cancel any async
requests which might be in flight before the device actually goes away.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Set the correct bits for nodev, stall and babble errors.
Raise errint irq. Fix state transition from WRITEBACK
to the next state.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Two bugs at once:
First the mask is backwards, so the it used to keeps the offset and
clears the page address, which is not what we need when we update the
offset.
Second the offset calculation is wrong in case head isn't page aligned.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds support for keeping multiple queues going at the same
time. One slow device will not affect other devices any more.
The patch adds code to manage EHCIQueue structs. It also does a number
of changes to the state machine:
* The state machine will never ever stop in EXECUTING any more.
Instead it will continue with the next queue (aka HORIZONTALQH) when
the usb device returns USB_RET_ASYNC.
* The state machine will stop processing when it figures it walks in
circles (easy to figure now that we have a EHCIQueue struct for each
QH we've processed). The bailout logic should not be needed any
more. For now it is still in, but will assert() in case it triggers.
* The state machine will just skip queues with a async USBPacket in
flight.
* The state machine will resume processing as soon as the async
USBPacket is finished.
The patch also takes care to flush the QH struct back to guest memory
when needed, so we don't get stale data when (re-)loading it from guest
memory in FETCHQH state.
It also makes the writeback code to not touch the first three dwords of
the QH struct as the EHCI must not write them. This actually fixes a
bug where QH chaining changes (next ptr) by the linux ehci driver where
overwritten by the emulated EHCI.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add EHCIQueue struct, move the fields needed to track the queue state
into that struct. Pass the new struct instead of ehci state down to
functions which handle the queue state. Lot of variable references have
changed due to that without an actual functional change.
Replace fetch_addr with two variables, one for async and one for
periodic schedule. Add functions to get and set the fetch address.
Use EHCIQueue->usb_status (old name: EHCIState->exec_status) directly in
ehci_execute_complete instead of passing around the status using a
parameters and the return value.
ehci_state_fetchqh returns a EHCIQueue struct now.
No change in behavior.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a separate tracepoint to log how register values change in response
to a mmio write. Especially useful for registers which have read-only
or clear-on-write bits in them.
No change in behavior.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Trace usb port operations (attach, detach, reset),
drop a few obsolete DPRINTF's.
No change in behavior.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add functions to get and set the current state of the state machine,
add tracepoints there to trace state transitions. Add support for
traceing the queue heads and transfer descriptors as we look at them.
Drop a few DPRINTFs and all DPRINTF_ST lines, they are obsolete now.
No change in behavior.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch starts adding trace support to ehci. It traces
updates of the status register (USBSTS), mmio access and
controller reset.
It also adds functions to set and clear status register bits
and puts them in use everywhere.
Some DPRINTF's are dropped in favor of the new tracepoints.
No change in behavior.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* rth/axp-next: (26 commits)
target-alpha: Implement TLB flush primitives.
target-alpha: Use a fixed frequency for the RPCC in system mode.
target-alpha: Trap for unassigned and unaligned addresses.
target-alpha: Remap PIO space for 43-bit KSEG for EV6.
target-alpha: Implement cpu_alpha_handle_mmu_fault for system mode.
target-alpha: Implement more CALL_PAL values inline.
target-alpha: Disable interrupts properly.
target-alpha: All ISA checks to use TB->FLAGS.
target-alpha: Swap shadow registers moving to/from PALmode.
target-alpha: Implement do_interrupt for system mode.
target-alpha: Add IPRs to be used by the emulation PALcode.
target-alpha: Use kernel mmu_idx for pal_mode.
target-alpha: Add various symbolic constants.
target-alpha: Use do_restore_state for arithmetic exceptions.
target-alpha: Tidy up arithmetic exceptions.
target-alpha: Tidy exception constants.
target-alpha: Enable the alpha-softmmu target.
target-alpha: Rationalize internal processor registers.
target-alpha: Merge HW_REI and HW_RET implementations.
target-alpha: Cleanup MMU modes.
...
BM_STATUS_INT is automatically set during ide_set_irq(), there's no reason to
set it manually in addition.
There is even one case where the interrupt status bit was set, but no IRQ was
raised. This is when the PRD table was reached but there is more data to
transfer. The correct behaviour for this case is not to set BM_STATUS_INT.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a dummy legacy ISA device whose responsibility is to
deploy sgabios, an option rom for a serial graphics adapter.
The proposal is that this device is always-on when -nographics,
but can otherwise be enable in any setup when -device sga is used.
[v2: suggestions on qdev by Markus ]
[v3: cleanups and documentation, per list suggestions ]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Switch no_user off and make it suppress the default VGA.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The simple backend only supports a maximum of 6 arguments. Split the
scsi_req_parsed event in two parts to cope with the limit.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The multiboot info struct's 'boot_device' field has 'part1' set to 0x01, which
maps to the second primary partition. To specify the first primary partition,
'part1' should be set to 0x00, since partition numbers start from zero
according to the multiboot spec.
Signed-off-by: Arun Thomas <arun.thomas@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
After the Qdev'ification of the MPC8544DS board and PCI bus, the internal
PCI bus name changed from "pci" to "pci.0". Reflect this change in the
search for that bus.
This patch enables networking on e500 guests again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Current rpath inline function is heavily used in all system calls.
This function has a static buffer making it a non-thread safe function.
This patch introduces new thread-safe routine and makes use of it.
Signed-off-by: Venkateswararao Jujjuri "<jvrao@linux.vnet.ibm.com>
Commit 353ac78d49 moved the files
without fixing the include paths. It used a modified CFLAGS
to add hw to the include search path, but this breaks builds
where the user wants to set special CFLAGS. Long include paths
also increase compilation time.
Therefore this patch removes the special CFLAGS for virtio
and fixes the include statements by using relative include paths.
v2: Remove special CFLAGS.
v3: Update needed for latest QEMU.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Venkateswararao Jujjuri (JV) <jvrao@linux.vnet.ibm.com>
This patch move the 9p device registration into its own file
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri (JV) <jvrao@linux.vnet.ibm.com>
v9fs_complete_rename() mistakenly renames files with similar name
as we don't check if the matched name is really an offspring.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: Venkateswararao Jujjuri (JV) <jvrao@linux.vnet.ibm.com>
Thanks to Tobias Hoffmann <th55@gmx.de> for this patch.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
After NACKing a read operation, a raising SCL should not trigger a new
read from the slave. Introduce a new state which just waits for a stop
or start condition after NACK.
Signed-off-by: Marcus Comstedt <marcus@mc.pp.se>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
All you could ever achieve with it is break stuff, so removing it
should be safe.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
