Swap 'buf' and 'bytes' around for consistency with
blk_co_{pread,pwrite}(), and in preparation to implement these functions
using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pread(blk, offset, buf, bytes, flags)
+ blk_pread(blk, offset, bytes, buf, flags)
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pwrite(blk, offset, buf, bytes, flags)
+ blk_pwrite(blk, offset, bytes, buf, flags)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-4-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement it using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes; @@
- blk_pread(blk, offset, buf, bytes)
+ blk_pread(blk, offset, buf, bytes, 0)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-3-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
They currently return the value of their 'bytes' parameter on success.
Make them return 0 instead, for consistency with other I/O functions and
in preparation to implement them using generated_co_wrapper. This also
makes it clear that short reads/writes are not possible.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Message-Id: <20220705161527.1054072-2-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
The mos6522 datasheet describes how the control lines IRQs are edge-triggered
according to the configuration in the PCR register. Implement the logic according
to the datasheet so that the interrupt bits in IFR are latched when the edge is
detected, and cleared when reading portA/portB or writing to IFR as necessary.
To maintain bisectibility this change also updates the SCSI, SCSI data, Nubus
and VIA2 60Hz/1Hz clocks in the q800 machine to be negative edge-triggered as
confirmed by the PCR programming in all of Linux, NetBSD and MacOS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The VIA2 on the Q800 machine is not a separate chip as in older Macs but instead
is integrated into the on-board logic. From analysing the SCSI routines in the
MacOS toolbox ROM (and to a lesser extent NetBSD and Linux) the expectation seems
to be that the SCSI_DATA (DRQ) bit is live on the Q800 and not latched.
Fortunately we can use the recently introduced mos6522 last_irq_levels variable
which tracks the edge-triggered state to return the SCSI_DATA (DRQ) bit live to
the guest OS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220305150957.5053-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Switch from using a legacy approach to the more formal approach for propagating
device reset to the parent.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
For historical reasons each mos6522 instance implements its own setting and
update of the IFR flag bits using methods exposed by MOS6522DeviceClass. As
of today this is no longer required, and it is now possible to implement
the mos6522 IRQs as standard qdev gpios.
Switch over to use qdev gpios for the mos6522 device and update all instances
accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
softmmu/rtc.c defines two public functions: qemu_get_timedate() and
qemu_timedate_diff(). Currently we keep the prototypes for these in
qemu-common.h, but most files don't need them. Move them to their
own header, a new include/sysemu/rtc.h.
Since the C files using these two functions did not need to include
qemu-common.h for any other reason, we can remove those include lines
when we add the include of the new rtc.h.
The license for the .h file follows that of the softmmu/rtc.c
where both the functions are defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add a new auxmode GPIO that is updated when port B bit 6 is changed indicating
whether the hardware is configured for A/UX mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211020134131.4392-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
According to both Linux and NetBSD, port B bit 6 is used on the Quadra 800 to
configure the GLUE logic in A/UX mode. Whilst the name VIA1B_vMystery isn't
particularly descriptive, the patch leaves this to ensure that the constants
in mac_via.c remain in sync with Linux's mac_via.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211020134131.4392-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Rename qbus_create_inplace() to qbus_init(); this is more in line
with our usual naming convention for functions that in-place
initialize objects.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210923121153.23754-5-peter.maydell@linaro.org
These will soon be required to enable nubus devices to support interrupts.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Now that q800 VIA1 and VIA2 are completely separate devices there is no need to
add a specific device prefix to ensure that the IRQ lines remain separate.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210830102447.10806-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Remove the mac_via device and wire up both q800 VIA1 and VIA2 directly for the
m68k q800 machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
After this change mac_via_reset() is now empty and can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210830102447.10806-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
These variables are already present in MOS6522Q800VIA1State and so it is just
the VMStateDescription move that is needed.
With this change the mac_via VMStateDescription is now empty and can be removed
completely.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The ADB is accessed using clock and data pins on q800 VIA1 port B and so can be
moved to MOS6522Q800VIA1State.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210830102447.10806-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PRAM/RTC is accessed using clock and data pins on q800 VIA1 port B and so
can be moved to MOS6522Q800VIA1State.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210830102447.10806-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PRAM contents are accessed using clock and data pins on q800 VIA1 port B
and so can be moved to MOS6522Q800VIA1State.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This variable is already present in MOS6522Q800VIA1State and can be moved
immediately into the q800 VIA1 VMStateDescription.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move the parent mos6522 objects from vmstate_mac_via into the new VMStateDescription
structures to begin the process of splitting MacVIAState into separate VIA1 and
VIA2 devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The original implementation of the Macintosh VIA devices in commit 6dca62a000
"hw/m68k: add VIA support" used timer optimisations to reduce high CPU usage on
the host when booting Linux. These optimisations worked by waiting until VIA1
port B was accessed before re-arming the timers.
The MacOS toolbox ROM constantly writes to VIA1 port B which calls
via1_one_second_update() and via1_sixty_hz_update() to calculate the new expiry
time, causing the timers to constantly reset and never fire. The effect of this
is that the Ticks (0x16a) global variable holding the number of 60Hz timer ticks
since reset is never incremented by the interrupt causing time to stand still.
Whilst the code was introduced as a performance optimisation, it is likely that
the high CPU usage was actually caused by the incorrect 60Hz timer interval
fixed in the previous patch. Remove the optimisation to keep everything simple
and enable the MacOS toolbox ROM to start keeping time.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210311100505.22596-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The 60Hz timer is initialised using timer_new_ns() meaning that the timer
interval should be measured in ns, and therefore its period is a thousand
times too short.
Use a define for the 60Hz timer period taking the more precise value as
documented in the Guide To The Macintosh Family Hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210311100505.22596-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
According to the "Guide To The Macintosh Family Hardware", the 60Hz VIA1 timer
on newer Macs such as the Quadra only exists for compatibility with old software
and is no longer synced to the VBL interval.
Rename the VBL timer to 60Hz timer to emphasise this and to prevent confusion
when the real VBL interrupt (now handled as a NuBus slot interrupt) is added in
future.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210311100505.22596-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The current workaround for the Linux ADB state machine in kernels < 5.6 switching
the VIA back to IDLE state between send and receive modes is to re-inject the
first byte of the response in the IDLE state, and then force the state machine
into generating an autopoll reply.
In fact what is happening is much simpler: analysis of traces from a real Quadra
suggest that the existing data is returned as the first autopoll response rather
than generating an immediate response starting whilst still in IDLE state.
Update the ADB receive code to work in the same way, which allows the re-injection
code to be completely removed from adb_via_receive() and for adb_via_poll() to
be simplified accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210311100505.22596-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS SCSI driver uses a long access to read the VIA registers rather than
just a single byte during the message out phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210311100505.22596-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The use of the post-increment operator on adb_data_in_index meant that the
trace-event was accidentally displaying the next byte in the incoming ADB
data buffer rather than the current byte.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210311100505.22596-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The 'running' argument from VMChangeStateHandler does not require
other value than 0 / 1. Make it a plain boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210111152020.1422021-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the MOS6522_DEVICE_CLASS and MOS6522_DEVICE_GET_CLASS
macros to be consistent with the TYPE_MOS6522 and MOS6522 macros.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200825192110.3528606-46-ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Handle this at the ADB bus level so that individual implementations do not need
to handle this themselves.
Finally add an assert() into adb_request() to prevent developers from accidentally
making an explicit ADB request without blocking autopoll.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20200623204936.24064-21-mark.cave-ayland@ilande.co.uk>
The existing ADB state machine is designed to work with Linux which has a different
interpretation of the state machine detailed in "Guide to the Macintosh Family
Hardware". In particular the current Linux implementation includes an extra change
to IDLE state when switching the VIA between send and receive modes which does not
occur in MacOS, and omitting this transition causes the current mac_via ADB state
machine to fail.
Rework the ADB state machine accordingly so that it can enumerate and autopoll the
ADB under both Linux and MacOS, including the addition of the new adb_autopoll_block()
and adb_autopoll_unblock() functions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20200623204936.24064-20-mark.cave-ayland@ilande.co.uk>
Currently the logic is split between the mos6522 portB_write() callback and
the memory region used to capture the VIA1 MMIO accesses. Move everything
into the latter mos6522_q800_via1_write() function to keep all the logic in
one place to make it easier to follow.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20200623204936.24064-19-mark.cave-ayland@ilande.co.uk>
mac_via_realize() creates a "mos6522-q800-via1" and a
"mos6522-q800-via2" device, but neglects to realize them. Affects
machine q800.
In theory, a device becomes real only on realize. In practice, the
transition from unreal to real is a fuzzy one. The work to make a
device real can be spread between realize methods (fine),
instance_init methods (wrong), and board code wiring up the device
(fine as long as it effectively happens on realize). Depending on
what exactly is done where, a device can work even when we neglect
to realize it.
These two appear to work. Nevertheless, it's a clear misuse of the
interface. Even when it works today (more or less by chance), it can
break tomorrow.
Fix by realizing them right away.
Fixes: 6dca62a000
Cc: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20200609122339.937862-9-armbru@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Laurent Vivier <laurent@vivier.eu>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
Check the return value of blk_write() and log an error if any
Fixes: Coverity CID 1412799 (Error handling issues)
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200210132252.381343-1-laurent@vivier.eu>
This allows to save and restore the content of the PRAM.
It may be useful if we want to check the configuration or to change it.
The backend is added using mtd interface, for instance:
... -drive file=pram.img,format=raw,if=mtd ...
where pram.img is the file where the data will be stored, its size must
be 256 bytes.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20191219201439.84804-3-laurent@vivier.eu>
The command byte is not decoded correctly.
This patch reworks the RTC/PRAM interface and fixes the problem.
It adds a comment before the function to explain how are encoded commands
and some trace-events to ease debugging.
Bug: https://bugs.launchpad.net/qemu/+bug/1856549
Fixes: 6dca62a000 ("hw/m68k: add VIA support")
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20191219201439.84804-2-laurent@vivier.eu>
VIA needs to be able to poll the ADB interface and to read/write data
from/to the bus.
This patch adds functions allowing that.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20191026164546.30020-7-laurent@vivier.eu>
Inside the 680x0 Macintosh, VIA (Versatile Interface Adapter) is used
to interface the keyboard, Mouse, and real-time clock. It also provides
control line for the floppy disk driver, video interface, sound circuitry
and serial interface.
This implementation is based on the MOS6522 object.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191026164546.30020-6-laurent@vivier.eu>
