There is no point in exposing an internal MMIO region via
SysBus and directly mapping it in the very same device.
Just map it without using the SysBus API.
Transformation done using the following coccinelle script:
@@
expression sbdev;
expression index;
expression addr;
expression subregion;
@@
- sysbus_init_mmio(sbdev, subregion);
... when != sbdev
- sysbus_mmio_map(sbdev, index, addr);
+ memory_region_add_subregion(get_system_memory(), addr, subregion);
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20231019131647.19690-8-philmd@linaro.org>
In order to make the next commit trivial, move sysbus_init_mmio()
calls just before the corresponding sysbus_mmio_map() calls.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20231019131647.19690-7-philmd@linaro.org>
The presenters for xive on P9 and P10 are mostly similar but the
behavior can be tuned through a few CQ registers. This patch adds a
"get_config" method, which will allow to access that config from the
presenter in a later patch.
For now, just define the config for the TIMA version.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The trigger message coming from a HW source contains a special bit
informing the XIVE interrupt controller that the PQ bits have been
checked at the source or not. Depending on the value, the IC can
perform the check and the state transition locally using its own PQ
state bits.
The following changes add new accessors to the XiveRouter required to
query and update the PQ state bits. This only applies to the PowerNV
machine. sPAPR accessors are provided but the pSeries machine should
not be concerned by such complex configuration for the moment.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Let devices specify transaction attributes when calling
dma_memory_rw().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-5-philmd@redhat.com>
and use them to set and test the ASSERTED bit of LSI sources.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211004212141.432954-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The h_int_reset() function resets the XIVE interrupt controller via
device_legacy_reset(). We know that the interrupt controller does
not have a qbus of its own, so the new device_cold_reset() function
(which resets both the device and its child buses) is equivalent here
to device_legacy_reset() and we can just switch to the new API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210503151849.8766-2-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
I have been keeping those logging messages in an ugly form for
while. Make them clean !
Beware not to activate all of them, this is really verbose.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201123163717.1368450-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sPAPR XIVE device is created by the machine in spapr_irq_init().
The latter overrides any value provided by the user with -global for
the "nr-irqs" and "nr-ends" properties with strictly positive values.
It seems reasonable to assume these properties should never be 0,
which wouldn't make much sense by the way.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120174646.619395-2-groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER9, the KVM XIVE device uses priority 7 for the escalation
interrupts. On POWER10, the host can use a reduced set of priorities
and KVM will configure the escalation priority to a lower number. In
any case, the guest is allowed to use priorities in a single range :
[ 0 .. (maxprio - 1) ].
Introduce a 'hv-prio' property to represent the escalation priority
number and use it to compute the "ibm,plat-res-int-priorities"
property defining the priority ranges reserved by the hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200819130843.2230799-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Calls to the KVM XIVE device are guarded by kvm_irqchip_in_kernel(). This
ensures that QEMU won't try to use the device if KVM is disabled or if
an in-kernel irqchip isn't required.
When using ic-mode=dual with the pseries machine, we have two possible
interrupt controllers: XIVE and XICS. The kvm_irqchip_in_kernel() helper
will return true as soon as any of the KVM device is created. It might
lure QEMU to think that the other one is also around, while it is not.
This is exactly what happens with ic-mode=dual at machine init when
claiming IRQ numbers, which must be done on all possible IRQ backends,
eg. RTAS event sources or the PHB0 LSI table : only the KVM XICS device
is active but we end up calling kvmppc_xive_source_reset_one() anyway,
which fails. This doesn't cause any trouble because of another bug :
kvmppc_xive_source_reset_one() lacks an error_setg() and callers don't
see the failure.
Most of the other kvmppc_xive_* functions have similar xive->fd
checks to filter out the case when KVM XIVE isn't active. It
might look safer to have idempotent functions but it doesn't
really help to understand what's going on when debugging.
Since we already have all the kvm_irqchip_in_kernel() in place,
also have the callers to check xive->fd as well before calling
KVM XIVE specific code. This is straight-forward for the spapr
specific XIVE code. Some more care is needed for the platform
agnostic XIVE code since it cannot access xive->fd directly.
Introduce new in_kernel() methods in some base XIVE classes
for this purpose and implement them only in spapr.
In all cases, we still need to call kvm_irqchip_in_kernel() so that
compilers can optimize the kvmppc_xive_* calls away when CONFIG_KVM
isn't defined, thus avoiding the need for stubs.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159679993438.876294.7285654331498605426.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
The "ibm,xive-lisn-ranges" defines ranges of interrupt numbers that
the guest can use to configure IPIs. It starts at 0 today but it could
change to some other offset. Make clear which IRQ range we are
exposing by using SPAPR_IRQ_IPI in the property definition.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200306123307.1348-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a temporary device_legacy_reset function doing what
device_reset does to prepare for the transition with Resettable
API.
All occurrence of device_reset in the code tree are also replaced
by device_legacy_reset.
The new resettable API has different prototype and semantics
(resetting child buses as well as the specified device). Subsequent
commits will make the changeover for each call site individually; once
that is complete device_legacy_reset() will be removed.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-2-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will be used in subsequent patches to access the XIVE associated to
a TCTX without reaching out to the machine through qdev_get_machine().
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[ groug: - split patch
- write subject and changelog ]
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE router base class currently inherits an empty realize hook
from the sysbus device base class, but it will soon implement one
of its own to perform some sanity checks. Do the preliminary plumbing
to have it called.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191219181155.32530-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When doing CAM line compares, fetch the block id from the interrupt
controller which can have set the PC_TCTXT_CHIPID field.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-20-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is now unused.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-16-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On the P9 Processor, the thread interrupt context registers of a CPU
can be accessed "directly" when by load/store from the CPU or
"indirectly" by the IC through an indirect TIMA page. This requires to
configure first the PC_TCTXT_INDIRx registers.
Today, we rely on the get_tctx() handler to deduce from the CPU PIR
the chip from which the TIMA access is being done. By handling the
TIMA memory ops under the interrupt controller model of each machine,
we can uniformize the TIMA direct and indirect ops under PowerNV. We
can also check that the CPUs have been enabled in the XIVE controller.
This prepares ground for the future versions of XIVE.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE and XICS-on-XIVE KVM devices on POWER9 hosts can greatly reduce
their consumption of some scarce HW resources, namely Virtual Presenter
identifiers, if they know the maximum number of vCPUs that may run in the
VM.
Prepare ground for this by passing the value down to xics_kvm_connect()
and kvmppc_xive_connect(). This is purely mechanical, no functional
change.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478678301.67101.2717368060417156338.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each XIVE Router model, sPAPR and PowerNV, now implements the 'match_nvt'
handler of the XivePresenter QOM interface. This is simply moving code
and taking into account the new API.
To be noted that the xive_router_get_tctx() helper is not used anymore
when doing CAM matching and will be removed later on after other changes.
The XIVE presenter model is still too simple for the PowerNV machine
and the CAM matching algo is not correct on multichip system. Subsequent
patches will introduce more changes to scan all chips of the system.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The END source object has both a pointer and a "xive" property pointing to
the router object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383333784.165747.5298512574054268786.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The source object has both a pointer and a "xive" property pointing to the
notifier object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383333227.165747.12901571295951957951.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SpaprInterruptControllerClass and PnvChipClass have an intc_create() method
that calls the appropriate routine, ie. icp_create() or xive_tctx_create(),
to establish the link between the VCPU and the presenter component of the
interrupt controller during realize.
There aren't any symmetrical call to be called when the VCPU gets unrealized
though. It is assumed that object_unparent() is the only thing to do.
This is questionable because the parenting logic around the CPU and
presenter objects is really an implementation detail of the interrupt
controller. It shouldn't be open-coded in the machine code.
Fix this by adding an intc_destroy() method that undoes what was done in
intc_create(). Also NULLify the presenter pointers to avoid having
stale pointers around. This will allow to reliably check if a vCPU has
a valid presenter.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157192724208.3146912.7254684777515287626.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
When a Virtual Processor is scheduled to run on a HW thread, the
hypervisor pushes its identifier in the OS CAM line. When running with
kernel_irqchip=off, QEMU needs to emulate the same behavior.
Set the OS CAM line when the interrupt presenter of the sPAPR core is
reset. This will also cover the case of hot-plugged CPUs.
This change also has the benefit to remove the use of CPU_FOREACH()
which can be unsafe.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191022163812.330-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On the sPAPR machine and PowerNV machine, the interrupt presenters are
created by a machine handler at the core level and are reset
independently. This is not consistent and it raises issues when it
comes to handle hot-plugged CPUs. In that case, the presenters are not
reset. This is less of an issue in XICS, although a zero MFFR could
be a concern, but in XIVE, the OS CAM line is not set and this breaks
the presenting algorithm. The current code has workarounds which need
a global cleanup.
Extend the sPAPR IRQ backend and the PowerNV Chip class with a new
cpu_intc_reset() handler called by the CPU reset handler and remove
the XiveTCTX reset handler which is now redundant.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191022163812.330-6-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The remaining logic in the post_load hook really belongs to the interrupt
controller backends, and just needs to be called on the active controller
(after the active controller is set to the right thing based on the
incoming migration in the generic spapr_irq_post_load() logic).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
It turns out that all the logic in the SpaprIrq::reset hooks (and some in
the SpaprIrq::post_load hooks) isn't really related to resetting the irq
backend (that's handled by the backends' own reset routines). Rather its
about getting the backend ready to be the active interrupt controller or
stopping being the active interrupt controller - reset (and post_load) is
just the only time that changes at present.
To make this flow clearer, move the logic into the explicit backend
activate and deactivate hooks.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly
through that, rather than dispatching via SpaprIrq with the dual
version having to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly
through that, rather than dispatching via SpaprIrq with the dual
version having to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly through
that, rather than dispatching via SpaprIrq with the dual version having
to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
These methods, like cpu_intc_create, really belong to the interrupt
controller, but need to be called on all possible intcs.
Like cpu_intc_create, therefore, make them methods on the intc and
always call it for all existing intcs.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method essentially represents code which belongs to the interrupt
controller, but needs to be called on all possible intcs, rather than
just the currently active one. The "dual" version therefore calls
into the xics and xive versions confusingly.
Handle this more directly, by making it instead a method on the intc
backend, and always calling it on every backend that exists.
While we're there, streamline the error reporting a bit.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The SpaprIrq structure is used to represent ths spapr machine's irq
backend. Except that it kind of conflates two concepts: one is the
backend proper - a specific interrupt controller that we might or
might not be using, the other is the irq configuration which covers
the layout of irq space and which interrupt controllers are allowed.
This leads to some pretty confusing code paths for the "dual"
configuration where its hooks redirect to other SpaprIrq structures
depending on the currently active irq controller.
To clean this up, we start by introducing a new
SpaprInterruptController QOM interface to represent strictly an
interrupt controller backend, not counting anything configuration
related. We implement this interface in the XICs and XIVE interrupt
controllers, and in future we'll move relevant methods from SpaprIrq
into it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
spapr_xive_irq_claim() returns a bool to indicate if it succeeded.
But most of the callers and one callee use int return values and/or an
Error * with more information instead. In any case, ints are a more
common idiom for success/failure states than bools (one never knows
what sense they'll be in).
So instead change to an int return value to indicate presence of error
+ an Error * to describe the details through that call chain.
It also didn't actually check if the irq was already claimed, which is
one of the primary purposes of the claim path, so do that.
spapr_xive_irq_free() also returned a bool... which no callers checked
and was always true, so just drop it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The irq claim and free paths for both XICS and XIVE check for some
validity conditions. Some of these represent genuine runtime failures,
however others - particularly checking that the basic irq number is in a
sane range - could only fail in the case of bugs in the callin code.
Therefore use assert()s instead of runtime failures for those.
In addition the non backend-specific part of the claim/free paths should
only be used for PAPR external irqs, that is in the range SPAPR_XIRQ_BASE
to the maximum irq number. Put assert()s for that into the top level
dispatchers as well.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
If an IRQ is allocated and not configured, such as a MSI requested by
a PCI driver, it can be saved in its default state and possibly later
on restored using the same state. If not initially MASKED, KVM will
try to find a matching priority/target tuple for the interrupt and
fail to restore the VM because 0/0 is not a valid target.
When allocating a IRQ number, the EAS should be set to a sane default :
VALID and MASKED.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190813164420.9829-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a better output of the XIVE END structures including the
escalation information and extend the PowerNV machine 'info pic'
command with a dump of the END EAS table used for escalations.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
