The MAC of the tulip card is stored in the EEPROM and at startup
tulip_fill_eeprom() is called to initialize the EEPROM with the MAC
address given on the command line, e.g.:
-device tulip,mac=00:11:22:33:44:55
In case the mac address was not given on the command line,
tulip_fill_eeprom() initializes the MAC in EEPROM with 00:00:00:00:00:00
which breaks e.g. a HP-UX guest.
Fix this problem by moving qemu_macaddr_default_if_unset() a few lines
up, so that a default mac address is assigned before tulip_fill_eeprom()
initializes the EEPROM.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
virtio_queue_host_notifier_read() tends to read pending event
left behind on ioeventfd in the vhost_net_stop() path, and
attempts to handle outstanding kicks from userspace vq handler.
However, in the ctrl_vq handler, virtio_net_handle_mq() has a
recursive call into virtio_net_set_status(), which may lead to
segmentation fault as shown in below stack trace:
0 0x000055f800df1780 in qdev_get_parent_bus (dev=0x0) at ../hw/core/qdev.c:376
1 0x000055f800c68ad8 in virtio_bus_device_iommu_enabled (vdev=vdev@entry=0x0) at ../hw/virtio/virtio-bus.c:331
2 0x000055f800d70d7f in vhost_memory_unmap (dev=<optimized out>) at ../hw/virtio/vhost.c:318
3 0x000055f800d70d7f in vhost_memory_unmap (dev=<optimized out>, buffer=0x7fc19bec5240, len=2052, is_write=1, access_len=2052) at ../hw/virtio/vhost.c:336
4 0x000055f800d71867 in vhost_virtqueue_stop (dev=dev@entry=0x55f8037ccc30, vdev=vdev@entry=0x55f8044ec590, vq=0x55f8037cceb0, idx=0) at ../hw/virtio/vhost.c:1241
5 0x000055f800d7406c in vhost_dev_stop (hdev=hdev@entry=0x55f8037ccc30, vdev=vdev@entry=0x55f8044ec590) at ../hw/virtio/vhost.c:1839
6 0x000055f800bf00a7 in vhost_net_stop_one (net=0x55f8037ccc30, dev=0x55f8044ec590) at ../hw/net/vhost_net.c:315
7 0x000055f800bf0678 in vhost_net_stop (dev=dev@entry=0x55f8044ec590, ncs=0x55f80452bae0, data_queue_pairs=data_queue_pairs@entry=7, cvq=cvq@entry=1)
at ../hw/net/vhost_net.c:423
8 0x000055f800d4e628 in virtio_net_set_status (status=<optimized out>, n=0x55f8044ec590) at ../hw/net/virtio-net.c:296
9 0x000055f800d4e628 in virtio_net_set_status (vdev=vdev@entry=0x55f8044ec590, status=15 '\017') at ../hw/net/virtio-net.c:370
10 0x000055f800d534d8 in virtio_net_handle_ctrl (iov_cnt=<optimized out>, iov=<optimized out>, cmd=0 '\000', n=0x55f8044ec590) at ../hw/net/virtio-net.c:1408
11 0x000055f800d534d8 in virtio_net_handle_ctrl (vdev=0x55f8044ec590, vq=0x7fc1a7e888d0) at ../hw/net/virtio-net.c:1452
12 0x000055f800d69f37 in virtio_queue_host_notifier_read (vq=0x7fc1a7e888d0) at ../hw/virtio/virtio.c:2331
13 0x000055f800d69f37 in virtio_queue_host_notifier_read (n=n@entry=0x7fc1a7e8894c) at ../hw/virtio/virtio.c:3575
14 0x000055f800c688e6 in virtio_bus_cleanup_host_notifier (bus=<optimized out>, n=n@entry=14) at ../hw/virtio/virtio-bus.c:312
15 0x000055f800d73106 in vhost_dev_disable_notifiers (hdev=hdev@entry=0x55f8035b51b0, vdev=vdev@entry=0x55f8044ec590)
at ../../../include/hw/virtio/virtio-bus.h:35
16 0x000055f800bf00b2 in vhost_net_stop_one (net=0x55f8035b51b0, dev=0x55f8044ec590) at ../hw/net/vhost_net.c:316
17 0x000055f800bf0678 in vhost_net_stop (dev=dev@entry=0x55f8044ec590, ncs=0x55f80452bae0, data_queue_pairs=data_queue_pairs@entry=7, cvq=cvq@entry=1)
at ../hw/net/vhost_net.c:423
18 0x000055f800d4e628 in virtio_net_set_status (status=<optimized out>, n=0x55f8044ec590) at ../hw/net/virtio-net.c:296
19 0x000055f800d4e628 in virtio_net_set_status (vdev=0x55f8044ec590, status=15 '\017') at ../hw/net/virtio-net.c:370
20 0x000055f800d6c4b2 in virtio_set_status (vdev=0x55f8044ec590, val=<optimized out>) at ../hw/virtio/virtio.c:1945
21 0x000055f800d11d9d in vm_state_notify (running=running@entry=false, state=state@entry=RUN_STATE_SHUTDOWN) at ../softmmu/runstate.c:333
22 0x000055f800d04e7a in do_vm_stop (state=state@entry=RUN_STATE_SHUTDOWN, send_stop=send_stop@entry=false) at ../softmmu/cpus.c:262
23 0x000055f800d04e99 in vm_shutdown () at ../softmmu/cpus.c:280
24 0x000055f800d126af in qemu_cleanup () at ../softmmu/runstate.c:812
25 0x000055f800ad5b13 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>) at ../softmmu/main.c:51
For now, temporarily disable handling MQ request from the ctrl_vq
userspace hanlder to avoid the recursive virtio_net_set_status()
call. Some rework is needed to allow changing the number of
queues without going through a full virtio_net_set_status cycle,
particularly for vhost-vdpa backend.
This patch will need to be reverted as soon as future patches of
having the change of #queues handled in userspace is merged.
Fixes: 402378407d ("vhost-vdpa: multiqueue support")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <1651890498-24478-8-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost_net_start() missed a corresponding stop_one() upon error from
vhost_set_vring_enable(). While at it, make the error handling for
err_start more robust. No real issue was found due to this though.
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <1651890498-24478-5-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
With MQ enabled vdpa device and non-MQ supporting guest e.g.
booting vdpa with mq=on over OVMF of single vqp, below assert
failure is seen:
../hw/virtio/vhost-vdpa.c:560: vhost_vdpa_get_vq_index: Assertion `idx >= dev->vq_index && idx < dev->vq_index + dev->nvqs' failed.
0 0x00007f8ce3ff3387 in raise () at /lib64/libc.so.6
1 0x00007f8ce3ff4a78 in abort () at /lib64/libc.so.6
2 0x00007f8ce3fec1a6 in __assert_fail_base () at /lib64/libc.so.6
3 0x00007f8ce3fec252 in () at /lib64/libc.so.6
4 0x0000558f52d79421 in vhost_vdpa_get_vq_index (dev=<optimized out>, idx=<optimized out>) at ../hw/virtio/vhost-vdpa.c:563
5 0x0000558f52d79421 in vhost_vdpa_get_vq_index (dev=<optimized out>, idx=<optimized out>) at ../hw/virtio/vhost-vdpa.c:558
6 0x0000558f52d7329a in vhost_virtqueue_mask (hdev=0x558f55c01800, vdev=0x558f568f91f0, n=2, mask=<optimized out>) at ../hw/virtio/vhost.c:1557
7 0x0000558f52c6b89a in virtio_pci_set_guest_notifier (d=d@entry=0x558f568f0f60, n=n@entry=2, assign=assign@entry=true, with_irqfd=with_irqfd@entry=false)
at ../hw/virtio/virtio-pci.c:974
8 0x0000558f52c6c0d8 in virtio_pci_set_guest_notifiers (d=0x558f568f0f60, nvqs=3, assign=true) at ../hw/virtio/virtio-pci.c:1019
9 0x0000558f52bf091d in vhost_net_start (dev=dev@entry=0x558f568f91f0, ncs=0x558f56937cd0, data_queue_pairs=data_queue_pairs@entry=1, cvq=cvq@entry=1)
at ../hw/net/vhost_net.c:361
10 0x0000558f52d4e5e7 in virtio_net_set_status (status=<optimized out>, n=0x558f568f91f0) at ../hw/net/virtio-net.c:289
11 0x0000558f52d4e5e7 in virtio_net_set_status (vdev=0x558f568f91f0, status=15 '\017') at ../hw/net/virtio-net.c:370
12 0x0000558f52d6c4b2 in virtio_set_status (vdev=vdev@entry=0x558f568f91f0, val=val@entry=15 '\017') at ../hw/virtio/virtio.c:1945
13 0x0000558f52c69eff in virtio_pci_common_write (opaque=0x558f568f0f60, addr=<optimized out>, val=<optimized out>, size=<optimized out>) at ../hw/virtio/virtio-pci.c:1292
14 0x0000558f52d15d6e in memory_region_write_accessor (mr=0x558f568f19d0, addr=20, value=<optimized out>, size=1, shift=<optimized out>, mask=<optimized out>, attrs=...)
at ../softmmu/memory.c:492
15 0x0000558f52d127de in access_with_adjusted_size (addr=addr@entry=20, value=value@entry=0x7f8cdbffe748, size=size@entry=1, access_size_min=<optimized out>, access_size_max=<optimized out>, access_fn=0x558f52d15cf0 <memory_region_write_accessor>, mr=0x558f568f19d0, attrs=...) at ../softmmu/memory.c:554
16 0x0000558f52d157ef in memory_region_dispatch_write (mr=mr@entry=0x558f568f19d0, addr=20, data=<optimized out>, op=<optimized out>, attrs=attrs@entry=...)
at ../softmmu/memory.c:1504
17 0x0000558f52d078e7 in flatview_write_continue (fv=fv@entry=0x7f8accbc3b90, addr=addr@entry=103079215124, attrs=..., ptr=ptr@entry=0x7f8ce6300028, len=len@entry=1, addr1=<optimized out>, l=<optimized out>, mr=0x558f568f19d0) at /home/opc/qemu-upstream/include/qemu/host-utils.h:165
18 0x0000558f52d07b06 in flatview_write (fv=0x7f8accbc3b90, addr=103079215124, attrs=..., buf=0x7f8ce6300028, len=1) at ../softmmu/physmem.c:2822
19 0x0000558f52d0b36b in address_space_write (as=<optimized out>, addr=<optimized out>, attrs=..., buf=buf@entry=0x7f8ce6300028, len=<optimized out>)
at ../softmmu/physmem.c:2914
20 0x0000558f52d0b3da in address_space_rw (as=<optimized out>, addr=<optimized out>, attrs=...,
attrs@entry=..., buf=buf@entry=0x7f8ce6300028, len=<optimized out>, is_write=<optimized out>) at ../softmmu/physmem.c:2924
21 0x0000558f52dced09 in kvm_cpu_exec (cpu=cpu@entry=0x558f55c2da60) at ../accel/kvm/kvm-all.c:2903
22 0x0000558f52dcfabd in kvm_vcpu_thread_fn (arg=arg@entry=0x558f55c2da60) at ../accel/kvm/kvm-accel-ops.c:49
23 0x0000558f52f9f04a in qemu_thread_start (args=<optimized out>) at ../util/qemu-thread-posix.c:556
24 0x00007f8ce4392ea5 in start_thread () at /lib64/libpthread.so.0
25 0x00007f8ce40bb9fd in clone () at /lib64/libc.so.6
The cause for the assert failure is due to that the vhost_dev index
for the ctrl vq was not aligned with actual one in use by the guest.
Upon multiqueue feature negotiation in virtio_net_set_multiqueue(),
if guest doesn't support multiqueue, the guest vq layout would shrink
to a single queue pair, consisting of 3 vqs in total (rx, tx and ctrl).
This results in ctrl_vq taking a different vhost_dev group index than
the default. We can map vq to the correct vhost_dev group by checking
if MQ is supported by guest and successfully negotiated. Since the
MQ feature is only present along with CTRL_VQ, we ensure the index
2 is only meant for the control vq while MQ is not supported by guest.
Fixes: 22288fe ("virtio-net: vhost control virtqueue support")
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <1651890498-24478-3-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the control virtqueue feature is absent or not negotiated,
vhost_net_start() still tries to set up vhost_dev and install
vhost notifiers for the control virtqueue, which results in
erroneous ioctl calls with incorrect queue index sending down
to driver. Do that only when needed.
Fixes: 22288fe ("virtio-net: vhost control virtqueue support")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <1651890498-24478-2-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds a get_vhost() callback function for VirtIODevices that
returns the device's corresponding vhost_dev structure, if the vhost
device is running. This patch also adds a vhost_started flag for
VirtIODevices.
Previously, a VirtIODevice wouldn't be able to tell if its corresponding
vhost device was active or not.
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <1648819405-25696-3-git-send-email-jonah.palmer@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch drops the name parameter for the virtio_init function.
The pair between the numeric device ID and the string device ID
(name) of a virtio device already exists, but not in a way that
lets us map between them.
This patch lets us do this and removes the need for the name
parameter in the virtio_init function.
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <1648819405-25696-2-git-send-email-jonah.palmer@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
"0x200000000" is much more readable than "8589934592".
The change saves one step (conversion) while debugging.
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Message-Id: <20220318140440.596019-1-i.maximets@ovn.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per https://discourse.gnome.org/t/port-your-module-from-g-memdup-to-g-memdup2-now/5538
The old API took the size of the memory to duplicate as a guint,
whereas most memory functions take memory sizes as a gsize. This
made it easy to accidentally pass a gsize to g_memdup(). For large
values, that would lead to a silent truncation of the size from 64
to 32 bits, and result in a heap area being returned which is
significantly smaller than what the caller expects. This can likely
be exploited in various modules to cause a heap buffer overflow.
Replace g_memdup() by the safer g_memdup2() wrapper.
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20220512175747.142058-6-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Change to generated file ebpf/rss.bpf.skeleton.h backed out]
All uses flush output immediately before or after qemu_log_unlock.
Instead of a separate call, move the flush into qemu_log_unlock.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-20-richard.henderson@linaro.org>
Inside qemu_log, we perform qemu_log_trylock/unlock, which need
not be done if we have already performed the lock beforehand.
Always check the result of qemu_log_trylock -- only checking
qemu_loglevel_mask races with the acquisition of the lock on
the logfile.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-10-richard.henderson@linaro.org>
This function can fail, which makes it more like ftrylockfile
or pthread_mutex_trylock than flockfile or pthread_mutex_lock,
so rename it.
To closer match the other trylock functions, release rcu_read_lock
along the failure path, so that qemu_log_unlock need not be called
on failure.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-8-richard.henderson@linaro.org>
Replace a config-time define with a compile time condition
define (compatible with clang and gcc) that must be declared prior to
its usage. This avoids having a global configure time define, but also
prevents from bad usage, if the config header wasn't included before.
This can help to make some code independent from qemu too.
gcc supports __BYTE_ORDER__ from about 4.6 and clang from 3.2.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[ For the s390x parts I'm involved in ]
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One less qemu-specific macro. It also helps to make some headers/units
only depend on glib, and thus moved in standalone projects eventually.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Patch created mechanically with:
$ spatch --in-place --sp-file scripts/coccinelle/use-g_new-etc.cocci \
--macro-file scripts/cocci-macro-file.h FILES...
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220315144156.1595462-4-armbru@redhat.com>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Commit bedd7e93d0 ("virtio-net: fix use after unmap/free for sg")
tries to fix the use after free of the sg by caching the virtqueue
elements in an array and unmap them at once after receiving the
packets, But it forgot to unmap the cached elements on error which
will lead to leaking of mapping and other unexpected results.
Fixing this by detaching the cached elements on error. This addresses
CVE-2022-26353.
Reported-by: Victor Tom <vv474172261@gmail.com>
Cc: qemu-stable@nongnu.org
Fixes: CVE-2022-26353
Fixes: bedd7e93d0 ("virtio-net: fix use after unmap/free for sg")
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
isa_init_irq() has become a trivial one-line wrapper for isa_get_irq().
It can therefore be removed.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com> (tpm_tis_isa)
Acked-by: Corey Minyard <cminyard@mvista.com> (isa_ipmi_bt, isa_ipmi_kcs)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220301220037.76555-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220307134353.1950-14-philippe.mathieu.daude@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
The code used to limit the maximum size of tx queue for others backends
than vhost_user since the introduction of configurable tx queue size in
9b02e1618c ("virtio-net: enable configurable tx queue size").
As vhost_user, vhost_vdpa devices should deal with memory region
crosses already, so let's use the full tx size.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20220217175029.2517071-1-eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
More than 1k of TypeInfo instances are already marked as const. Mark the
remaining ones, too.
This commit was created with:
git grep -z -l 'static TypeInfo' -- '*.c' | \
xargs -0 sed -i 's/static TypeInfo/static const TypeInfo/'
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20220117145805.173070-2-shentey@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In section 7.4.3 of the 82574 datasheet it states that
"In systems that do not support MSI-X, reading the ICR
register clears it's bits..."
Some OSes rely on this.
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The "Interrupt Cause" register (VMXNET3_REG_ICR) is read-only.
Write accesses are ignored. Log them with as LOG_GUEST_ERROR
instead of aborting:
[R +0.239743] writeq 0xe0002031 0x46291a5a55460800
ERROR:hw/net/vmxnet3.c:1819:vmxnet3_io_bar1_write: code should not be reached
Thread 1 "qemu-system-i38" received signal SIGABRT, Aborted.
(gdb) bt
#3 0x74c397d3 in __GI_abort () at abort.c:79
#4 0x76d3cd4c in g_assertion_message (domain=<optimized out>, file=<optimized out>, line=<optimized out>, func=<optimized out>, message=<optimized out>) at ../glib/gtestutils.c:3223
#5 0x76d9d45f in g_assertion_message_expr
(domain=0x0, file=0x59fc2e53 "hw/net/vmxnet3.c", line=1819, func=0x59fc11e0 <__func__.vmxnet3_io_bar1_write> "vmxnet3_io_bar1_write", expr=<optimized out>)
at ../glib/gtestutils.c:3249
#6 0x57e80a3a in vmxnet3_io_bar1_write (opaque=0x62814100, addr=56, val=70, size=4) at hw/net/vmxnet3.c:1819
#7 0x58c2d894 in memory_region_write_accessor (mr=0x62816b90, addr=56, value=0x7fff9450, size=4, shift=0, mask=4294967295, attrs=...) at softmmu/memory.c:492
#8 0x58c2d1d2 in access_with_adjusted_size (addr=56, value=0x7fff9450, size=1, access_size_min=4, access_size_max=4, access_fn=
0x58c2d290 <memory_region_write_accessor>, mr=0x62816b90, attrs=...) at softmmu/memory.c:554
#9 0x58c2bae7 in memory_region_dispatch_write (mr=0x62816b90, addr=56, data=70, op=MO_8, attrs=...) at softmmu/memory.c:1504
#10 0x58bfd034 in flatview_write_continue (fv=0x606000181700, addr=0xe0002038, attrs=..., ptr=0x7fffb9e0, len=1, addr1=56, l=1, mr=0x62816b90)
at softmmu/physmem.c:2782
#11 0x58beba00 in flatview_write (fv=0x606000181700, addr=0xe0002031, attrs=..., buf=0x7fffb9e0, len=8) at softmmu/physmem.c:2822
#12 0x58beb589 in address_space_write (as=0x608000015f20, addr=0xe0002031, attrs=..., buf=0x7fffb9e0, len=8) at softmmu/physmem.c:2914
Reported-by: Dike <dike199774@qq.com>
Reported-by: Duhao <504224090@qq.com>
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2032932
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The migration code will not look at a VMStateDescription's
minimum_version_id_old field unless that VMSD has set the
load_state_old field to something non-NULL. (The purpose of
minimum_version_id_old is to specify what migration version is needed
for the code in the function pointed to by load_state_old to be able
to handle it on incoming migration.)
We have exactly one VMSD which still has a load_state_old,
in the PPC CPU; every other VMSD which sets minimum_version_id_old
is doing so unnecessarily. Delete all the unnecessary ones.
Commit created with:
sed -i '/\.minimum_version_id_old/d' $(git grep -l '\.minimum_version_id_old')
with the one legitimate use then hand-edited back in.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
---
It missed vmstate_ppc_cpu.
The Marvell 88W8618 network device is hidden in the Musicpal
machine. Move it into a new unit file under the hw/net/ directory.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 497679d510.
Fixes: 497679d510 ("virtio-net: add support for configure interrupt")
Cc: "Cindy Lu" <lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add functions to support configure interrupt in virtio_net
The functions are config_pending and config_mask, while
this input idx is VIRTIO_CONFIG_IRQ_IDX will check the
function of configure interrupt.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-9-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To support configure interrupt for vhost-vdpa
Introduce VIRTIO_CONFIG_IRQ_IDX -1 as configure interrupt's queue index,
Then we can reuse the functions guest_notifier_mask and guest_notifier_pending.
Add the check of queue index in these drivers, if the driver does not support
configure interrupt, the function will just return
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-2-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ld*_dma() returns a MemTxResult type. Do not discard
it, return it to the caller.
Update the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-24-philmd@redhat.com>
Let devices specify transaction attributes when calling ld*_pci_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-22-philmd@redhat.com>
Let devices specify transaction attributes when calling st*_pci_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-21-philmd@redhat.com>
virtio-net-failover test tries several device combinations that produces
some expected warnings.
These warning can be confusing, so we disable them during the qtest
sequence.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20211220145314.390697-1-lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
[thuth: Fix memory leak by using error_free()]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The rx_active boolean change to true should always trigger a try_read
call that flushes the queue.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20211203221002.1719306-1-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While activating device in vmxnet3_acticate_device(), it does not
validate guest supplied configuration values against predefined
minimum - maximum limits. This may lead to integer overflow or
OOB access issues. Add checks to avoid it.
Fixes: CVE-2021-20203
Buglink: https://bugs.launchpad.net/qemu/+bug/1913873
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The -1 assumes that cvq device model is accounted in data_queue_pairs,
if cvq does not exists, but it's actually the opposite: Devices with
!cvq are ok but devices with cvq does not add the last queue to
data_queue_pairs.
This is not a problem to vhost-net, but it is to vhost-vdpa:
* Devices with cvq gets initialized at last data vq device model, not
at cvq one.
* Devices with !cvq never gets initialized, since last_index is the
first queue of the last device model.
Because of that, the right change in last_index is to actually add the
cvq, not to remove the missing one.
This is not a problem to vhost-net, but it is to vhost-vdpa, which
device model trust to reach the last index to finish starting the
device.
Also, as the previous commit, rename it to index_end.
Tested with vp_vdpa with host's vhost=on and vhost=off, with ctrl_vq=on
and ctrl_vq=off.
Fixes: 049eb15b5f ("vhost: record the last virtqueue index for the virtio device")
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20211104085625.2054959-3-eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The doc of this field pointed out that last_index is the last vq index.
This is misleading, since it's actually one past the end of the vqs.
Renaming and modifying comment.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211104085625.2054959-2-eperezma@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The fact that the MMIO handler is not re-entrant causes an infinite
loop under certain conditions:
Guest write to TDT -> Loopback -> RX (DMA to TDT) -> TX
We now eliminate the effect of this problem locally in e1000, by adding
a boolean in struct E1000State indicating when the TX side is busy. This
will cause any entering new call to return early instead of interfering
with the ongoing work, and eliminates any risk of looping.
This is intended to address CVE-2021-20257.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch implements the control virtqueue support for vhost. This
requires virtio-net to figure out the datapath queue pairs and control
virtqueue via is_datapath and pass the number of those two types
of virtqueues to vhost_net_start()/vhost_net_stop().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211020045600.16082-10-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces a new field in the vhost_dev structure to record
the last virtqueue index for the virtio device. This will be useful
for the vhost backends with 1:N model to start or stop the device
after all the vhost_dev structures were started or stopped.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211020045600.16082-9-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Most of the time, "queues" really means queue pairs. So this patch
switch to use "queue_pairs" to avoid confusion.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211020045600.16082-8-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We assume there's no cvq in the past, this is not true when we need
control virtqueue support for vhost-user backends. So this patch
implements the control virtqueue support for vhost-net. As datapath,
the control virtqueue is also required to be coupled with the
NetClientState. The vhost_net_start/stop() are tweaked to accept the
number of datapath queue pairs plus the the number of control
virtqueue for us to start and stop the vhost device.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211020045600.16082-7-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit f3a8505656 ("qdev/qbus: add hidden device support") has
introduced a generic way to hide a device but it has modified
qdev_device_add() to check a specific option of the failover device,
"failover_pair_id", before calling the generic mechanism.
It's not needed (and not generic) to do that in qdev_device_add() because
this is also checked by the failover_hide_primary_device() function that
uses the generic mechanism to hide the device.
Cc: Jens Freimann <jfreimann@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20211019071532.682717-3-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
The hide_device helper can be called several times for the same
devices as it shouldn't change any state and should only return an
information.
But not to rely anymore on QemuOpts we have introduced a new field
to store the parameters of the device and don't allow to update it
once it is done.
And as the function is called several times, we ends with:
warning: Cannot attach more than one primary device to 'virtio0'
That is not only a warning as it prevents to hide the device and breaks
failover.
Fix that by checking the device id.
Now, we fail only if the virtio-net device is really used by two different
devices, for instance:
-device virtio-net-pci,id=virtio0,failover=on,... \
-device vfio-pci,id=hostdev0,failover_pair_id=virtio0,... \
-device e1000e,id=e1000e0,failover_pair_id=virtio0,... \
will exit with:
Cannot attach more than one primary device to 'virtio0': 'hostdev0' and 'e1000e0'
Fixes: 259a10dbcb ("virtio-net: Store failover primary opts pointer locally")
Cc: kwolf@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20211019071532.682717-2-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
QDicts are both what QMP natively uses and what the keyval parser
produces. Going through QemuOpts isn't useful for either one, so switch
the main device creation function to QDicts. By sharing more code with
the -object/object-add code path, we can even reduce the code size a
bit.
This commit doesn't remove the detour through QemuOpts from any code
path yet, but it allows the following commits to do so.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20211008133442.141332-15-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Don't go through the global QemuOptsList, it is state of the legacy
command line parser and we will create devices that are not contained
in it. It is also just the command line configuration and not
necessarily the current runtime state.
Instead, look at the qdev device tree which has the current state of all
existing devices.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20211008133442.141332-14-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of accessing the global QemuOptsList, which really belong to the
command line parser and shouldn't be accessed from devices, store a
pointer to the QemuOpts in a new VirtIONet field.
This is not the final state, but just an intermediate step to get rid of
QemuOpts in devices. It will later be replaced with an options QDict.
Before this patch, two "primary" devices could be hidden for the same
standby device, but only one of them would actually be enabled and the
other one would be kept hidden forever, so this doesn't make sense.
After this patch, configuring a second primary device is an error.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20211008133442.141332-13-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
hide_device() is used for virtio-net failover, where the standby virtio
device delays creation of the primary device. It only makes sense to
have a single primary device for each standby device. Adding a second
one should result in an error instead of hiding it and never using it
afterwards.
Prepare for this by adding an Error parameter to the hide_device()
callback where virtio-net is informed about adding a primary device.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20211008133442.141332-12-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When mergeable buffer is enabled, we try to set the num_buffers after
the virtqueue elem has been unmapped. This will lead several issues,
E.g a use after free when the descriptor has an address which belongs
to the non direct access region. In this case we use bounce buffer
that is allocated during address_space_map() and freed during
address_space_unmap().
Fixing this by storing the elems temporarily in an array and delay the
unmap after we set the the num_buffers.
This addresses CVE-2021-3748.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: fbe78f4f55 ("virtio-net support")
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to initialize dev.nvqs from the VhostNetOptions
instead of assuming it was 2. This is useful for implementing control
virtqueue support which will be a single vhost_net structure with a
single cvq.
Note that nvqs is still set to 2 for all users and this patch does not
change functionality.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210903091031.47303-6-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The nvqs and vqs have been initialized during vhost_net_init() and are
not expected to change during the life cycle of vhost_net
structure. So this patch removes the meaningless assignment.
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210903091031.47303-4-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the legacy RX descriptor mode, VLAN tag was saved to d->special
by e1000e_build_rx_metadata() in e1000e_write_lgcy_rx_descr(), but
it was then zeroed out again at the end of the call, which is wrong.
Fixes: c89d416a2b ("e1000e: Don't zero out buffer address in rx descriptor")
Reported-by: Markus Carlstedt <markus.carlstedt@windriver.com>
Signed-off-by: Christina Wang <christina.wang@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The initial value of VLAN Ether Type (VET) register is 0x8100, as per
the manual and real hardware.
While Linux e1000e driver always writes VET register to 0x8100, it is
not always the case for everyone. Drivers relying on the reset value
of VET won't be able to transmit and receive VLAN frames in QEMU.
Unlike e1000 in QEMU, e1000e uses a field 'vet' in "struct E1000Core"
to cache the value of VET register, but the cache only gets updated
when VET register is written. To always get a consistent VET value
no matter VET is written or remains its reset value, drop the 'vet'
field and use 'core->mac[VET]' directly.
Reported-by: Markus Carlstedt <markus.carlstedt@windriver.com>
Signed-off-by: Christina Wang <christina.wang@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The initial value of VLAN Ether Type (VET) register is 0x8100, as per
the manual and real hardware.
While Linux e1000 driver always writes VET register to 0x8100, it is
not always the case for everyone. Drivers relying on the reset value
of VET won't be able to transmit and receive VLAN frames in QEMU.
Reported-by: Markus Carlstedt <markus.carlstedt@windriver.com>
Signed-off-by: Christina Wang <christina.wang@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Problem reported by openEuler fuzz-sig group.
The buff2frame_bas function (hw\net\can\can_sja1000.c)
infoleak(qemu5.x~qemu6.x) or stack-overflow(qemu 4.x).
Reported-by: Qiang Ning <ningqiang1@huawei.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
QEMU should never terminate unexpectedly just because the guest is
doing something wrong like specifying wrong queue numbers. Let's
simply refuse to set the device active in this case.
Buglink: https://bugs.launchpad.net/qemu/+bug/1890160
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
QEMU currently crashes when it's started like this:
cat << EOF | ./qemu-system-i386 -device vmxnet3 -nodefaults -qtest stdio
outl 0xcf8 0x80001014
outl 0xcfc 0xe0001000
outl 0xcf8 0x80001018
outl 0xcf8 0x80001004
outw 0xcfc 0x7
outl 0xcf8 0x80001083
write 0x0 0x1 0xe1
write 0x1 0x1 0xfe
write 0x2 0x1 0xbe
write 0x3 0x1 0xba
writeq 0xe0001020 0xefefff5ecafe0000
writeq 0xe0001020 0xffff5e5ccafe0002
EOF
It hits this assertion:
qemu-system-i386: ../qemu/hw/net/net_tx_pkt.c:453: net_tx_pkt_reset:
Assertion `pkt->raw' failed.
This happens because net_tx_pkt_init() is called with max_frags == 0 and
thus the allocation
p->raw = g_new(struct iovec, max_frags);
results in a NULL pointer that causes the
assert(pkt->raw);
in net_tx_pkt_reset() to fail later. To fix this issue we can check
that max_raw_frags was not zero before asserting that pkt->raw is
a non-NULL pointer.
Buglink: https://bugs.launchpad.net/qemu/+bug/1890157
Message-Id: <20210715193219.1132571-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
QEMU should never abort just because the guest is doing something odd.
Let's simply log the error and ignore the bad transmit queue instead.
Buglink: https://bugs.launchpad.net/qemu/+bug/1926111
Message-Id: <20210715103755.1035566-1-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The GDateTime APIs provided by GLib avoid portability pitfalls, such
as some platforms where 'struct timeval.tv_sec' field is still 'long'
instead of 'time_t'. When combined with automatic cleanup, GDateTime
often results in simpler code too.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Commit 3fe9a838ec "dp8393x: Always use 32-bit accesses" set .impl.min_access_size
and .impl.max_access_size to 4 to try and fix the Linux jazzsonic driver which uses
32-bit accesses.
The problem with forcing the register access to 32-bit in this way is that since the
dp8393x uses 16-bit registers, a manual endian swap is required for devices on big
endian machines with 32-bit accesses.
For both access sizes and machine endians the QEMU memory API can do the right thing
automatically: all that is needed is to set .impl.min_access_size to 2 to declare that
the dp8393x implements 16-bit registers.
Normally .impl.max_access_size should also be set to 2, however that doesn't quite
work in this case since the register stride is specified using a (dynamic) it_shift
property which is applied during the MMIO access itself. The effect of this is that
for a 32-bit access the memory API performs 2 x 16-bit accesses, but the use of
it_shift within the MMIO access itself causes the register value to be repeated in both
the top 16-bits and bottom 16-bits. The Linux jazzsonic driver expects the stride to be
zero-extended up to access size and therefore fails to correctly detect the dp8393x
device due to the extra data in the top 16-bits.
The solution here is to remove .impl.max_access_size so that the memory API will
correctly zero-extend the 16-bit registers to the access size up to and including
it_shift. Since it_shift is never greater than 2 than this will always do the right
thing for both 16-bit and 32-bit accesses regardless of the machine endian, allowing
the manual endian swap code to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 3fe9a838ec ("dp8393x: Always use 32-bit accesses")
Message-Id: <20210705214929.17222-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead of accessing N registers via a single address_space API
call using a temporary buffer (stored in the device state) and
updating each register, move the address_space call in the
register put/get. The load/store and word size checks are moved
to put/get too. This simplifies a bit, making the code easier
to read.
Co-developed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210710174954.2577195-8-f4bug@amsat.org>
Per the DP83932C datasheet from July 1995:
4.0 SONIC Registers
4.1 THE CAM UNIT
The Content Addressable Memory (CAM) consists of sixteen
48-bit entries for complete address filtering of network
packets. Each entry corresponds to a 48-bit destination
address that is user programmable and can contain any
combination of Multicast or Physical addresses. Each entry
is partitioned into three 16-bit CAM cells accessible
through CAM Address Ports (CAP 2, CAP 1 and CAP 0) with
CAP0 corresponding to the least significant 16 bits of
the Destination Address and CAP2 corresponding to the
most significant bits.
Store the CAM registers as 16-bit as it simplifies the code.
Having now the CAM registers as arrays of 3 uint16_t, we can avoid
using the VMSTATE_BUFFER_UNSAFE macro by using VMSTATE_UINT16_2DARRAY
which is more appropriate. This breaks the migration stream however.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210710174954.2577195-5-f4bug@amsat.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210710174954.2577195-3-f4bug@amsat.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Replace address_space_rw(is_write=1) by address_space_write()
and remove pointless cast.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210710174954.2577195-2-f4bug@amsat.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently when a LOAD CAM command is executed the entries are loaded into the
CAM from memory in order which is incorrect. According to the datasheet the
first entry in the CAM descriptor is the entry index which means that each
descriptor may update any single entry in the CAM rather than the Nth entry.
Decode the CAM entry index and use it store the descriptor in the appropriate
slot in the CAM. This fixes the issue where the MacOS toolbox loads a single
CAM descriptor into the final slot in order to perform a loopback test which
must succeed before the Ethernet port is enabled.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625065401.30170-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
- Extract nanoMIPS, microMIPS, Code Compaction from translate.c
- Allow PCI config accesses smaller than 32-bit on Bonito64 device
- Fix migration of g364fb device on Jazz Magnum
- Fix dp8393x PROM checksum on Jazz Magnum and Quadra 800
- Map the UART devices unconditionally on Jazz Magnum
- Add functional test booting Linux on the Fuloong 2E
-----BEGIN PGP SIGNATURE-----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=rR+B
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd/tags/mips-20210702' into staging
MIPS patches queue
- Extract nanoMIPS, microMIPS, Code Compaction from translate.c
- Allow PCI config accesses smaller than 32-bit on Bonito64 device
- Fix migration of g364fb device on Jazz Magnum
- Fix dp8393x PROM checksum on Jazz Magnum and Quadra 800
- Map the UART devices unconditionally on Jazz Magnum
- Add functional test booting Linux on the Fuloong 2E
# gpg: Signature made Fri 02 Jul 2021 16:36:19 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd/tags/mips-20210702:
hw/mips/jazz: Map the UART devices unconditionally
hw/mips/jazz: specify correct endian for dp8393x device
hw/m68k/q800: fix PROM checksum and MAC address storage
qemu/bitops.h: add bitrev8 implementation
dp8393x: remove onboard PROM containing MAC address and checksum
hw/m68k/q800: move PROM and checksum calculation from dp8393x device to board
hw/mips/jazz: move PROM and checksum calculation from dp8393x device to board
dp8393x: convert to trace-events
dp8393x: checkpatch fixes
g364fb: add VMStateDescription for G364SysBusState
g364fb: use RAM memory region for framebuffer
tests/acceptance: Test Linux on the Fuloong 2E machine
hw/pci-host/bonito: Allow PCI config accesses smaller than 32-bit
hw/pci-host/bonito: Trace PCI config accesses smaller than 32-bit
target/mips: Extract nanoMIPS ISA translation routines
target/mips: Extract the microMIPS ISA translation routines
target/mips: Extract Code Compaction ASE translation routines
target/mips: Add declarations for generic TCG helpers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the card is plugged back, reset the partially_hotplugged flag to false
Bug: https://bugzilla.redhat.com/show_bug.cgi?id=1787194
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210629152937.619193-1-lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to the datasheet the dp8393x chipset does not contain any NVRAM capable
of storing a MAC address or checksum. Now that both the MIPS jazz and m68k q800
boards generate the PROM region and checksum themselves, remove the generated
PROM from the dp8393x device itself.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625065401.30170-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210625065401.30170-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Also fix a simple comment typo of "constrainst" to "constraints".
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210625065401.30170-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instead of just returning 0/-1 and letting the caller make up a
meaningless error message, add an Error parameter to allow reporting the
real error and switch to 0/-errno so that different kind of errors can
be distinguished in the caller.
config_len in vhost_user_get_config() is defined by the device, so if
it's larger than VHOST_USER_MAX_CONFIG_SIZE, this is a programming
error. Turn the corresponding check into an assertion.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-6-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This allows callers to return better error messages instead of making
one up while the real error ends up on stderr. Most callers can
immediately make use of this because they already have an Error
parameter themselves. The others just keep printing the error with
error_report_err().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-2-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When RSS is enabled the device tries to load the eBPF program
to select RX virtqueue in the TUN. If eBPF can be loaded
the RSS will function also with vhost (works with kernel 5.8 and later).
Software RSS is used as a fallback with vhost=off when eBPF can't be loaded
or when hash population requested by the guest.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJgrwypAAoJEO8Ells5jWIRDfsIAJyrDUbgDoeg4dM9TEvE+3xr
5Fd52wVozlQhn6zz2ZfEcqVfWNVbVHsVcYnpJQMXOCda5CIl5qZbl2EzS/lBrdkm
f5XUD4lFhwH1pUUugT20lEFYct0dv2UddEmLrEctI+CB5d9bA+SqeDdLAHYbrDIR
jfc/vOrP/1sfvWCsXmZzJ+0UhoGoS8qU2eLx9nwSvan3uLMmLWfWSTUltvwMNvZD
oA6a1O9poV00W89W25tSeMOKKPaS+RZYVFvDd0HzQYRI0t496VxK/Jw0VqfF+iCl
3KBzjhUi7QyFWgQY5xFQcMWwob8McOJOUGX4EQERm8EbHy8VhpugCHinqLPqf38=
=fRpo
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Thu 27 May 2021 04:06:17 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
tap-bsd: Remove special casing for older OpenBSD releases
virtio-net: failover: add missing remove_migration_state_change_notifier()
hw/net/imx_fec: return 0xffff when accessing non-existing PHY
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the failover case configuration, virtio_net_device_realize() uses an
add_migration_state_change_notifier() to add a state notifier, but this
notifier is not removed by the unrealize function when the virtio-net
card is unplugged.
If the card is unplugged and a migration is started, the notifier is
called and as it is not valid anymore QEMU crashes.
This patch fixes the problem by adding the
remove_migration_state_change_notifier() in virtio_net_device_unrealize().
The problem can be reproduced with:
$ qemu-system-x86_64 -enable-kvm -m 1g -M q35 \
-device pcie-root-port,slot=4,id=root1 \
-device pcie-root-port,slot=5,id=root2 \
-device virtio-net-pci,id=net1,mac=52:54:00:6f:55:cc,failover=on,bus=root1 \
-monitor stdio disk.qcow2
(qemu) device_del net1
(qemu) migrate "exec:gzip -c > STATEFILE.gz"
Thread 1 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
0x0000000000000000 in ?? ()
(gdb) bt
#0 0x0000000000000000 in ()
#1 0x0000555555d726d7 in notifier_list_notify (...)
at .../util/notify.c:39
#2 0x0000555555842c1a in migrate_fd_connect (...)
at .../migration/migration.c:3975
#3 0x0000555555950f7d in migration_channel_connect (...)
error@entry=0x0) at .../migration/channel.c:107
#4 0x0000555555910922 in exec_start_outgoing_migration (...)
at .../migration/exec.c:42
Reported-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
If a PHY does not exist, attempts to read from it should return 0xffff.
Otherwise the Linux kernel will believe that a PHY is there and select
the non-existing PHY. This in turn will result in network errors later
on since the real PHY is not selected or configured.
Since reading from or writing to a non-existing PHY is not an emulation
error, replace guest error messages with traces.
Fixes: 461c51ad42 ("Add a phy-num property to the i.MX FEC emulator")
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmCeiMEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpqsIH/A49Av5Bv8huL75lf9GzCx3E1a/z2W9Fphik
OcQ1ahR+7CRDARub+vTG40MBmZBVefIWjLAj3BwBWzFGPX0DZq0zeI102VzlEVKY
OeUx8ixuiKOSLcS+QxE7ZXIBL2Pn7l+MFUi4nLMYKti7c/kola7zlB57qsmXh+VD
AOQ7Utj6NWoi6QocWJsMSCyHCh3Fk9QzcStLlr6/MkSJa1zqv8l22+8oWH07Fk2M
wZfhrm9k094on28iSejsFYL5e4ROeXUajbOdfyMIxWvAB7boC9Jxk/e0oAbuSB4y
2f71Gfk3mU6irS7PvrxcKbk6BVD2zxM2WumOchZJgxFAujDO6yg=
=fvkT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,virtio: bugfixes, improvements
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 14 May 2021 15:27:13 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
Fix build with 64 bits time_t
vhost-vdpa: Make vhost_vdpa_get_device_id() static
hw/virtio: enable ioeventfd configuring for mmio
hw/smbios: support for type 41 (onboard devices extended information)
checkpatch: Fix use of uninitialized value
virtio-scsi: Configure all host notifiers in a single MR transaction
virtio-scsi: Set host notifiers and callbacks separately
virtio-blk: Configure all host notifiers in a single MR transaction
virtio-blk: Fix rollback path in virtio_blk_data_plane_start()
pc-dimm: remove unnecessary get_vmstate_memory_region() method
amd_iommu: fix wrong MMIO operations
virtio-net: Constify VirtIOFeature feature_sizes[]
virtio-blk: Constify VirtIOFeature feature_sizes[]
hw/virtio: Pass virtio_feature_get_config_size() a const argument
x86: acpi: use offset instead of pointer when using build_header()
amd_iommu: Fix pte_override_page_mask()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/arm/virt.c
Target lm32 was deprecated in commit d849800512, v5.2.0. See there
for rationale.
Some of its code lives on in device models derived from milkymist
ones: hw/char/digic-uart.c and hw/display/bcm2835_fb.c.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-2-armbru@redhat.com>
Acked-by: Michael Walle <michael@walle.cc>
[Trivial conflicts resolved, reST markup fixed]
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including cpu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-4-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including sysemu/sysemu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-2-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Several issues has been reported for query-netdev info
series. Consider it's late in the rc, this reverts commit
commit 59b5437eb7.
Signed-off-by: Jason Wang <jasowang@redhat.com>
As the comment of tx_padding_and_crc() says: "Never add CRC in QEMU",
min_frame_len should excluce CRC, so it should be 60 instead of 64.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210316081505.72898-1-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For virtio-net, there is no need to pad the Ethernet frame size to
60 bytes before sending to it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The info_str field of the NetClientState structure is static and has a size
of 256 bytes. This amount is often unclaimed, and the field itself is used
exclusively for HMP "info network".
The patch translates info_str to dynamic memory allocation.
This action is also allows us to painlessly discard usage of this field
for backend devices.
Signed-off-by: Alexey Kirillov <lekiravi@yandex-team.ru>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Buglink: https://bugs.launchpad.net/qemu/+bug/1917085
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Buglink: https://bugs.launchpad.net/qemu/+bug/1910826
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_receive_iov() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
During procss_tx_desc(), driver can try to chain data descriptor with
legacy descriptor, when will lead underflow for the following
calculation in process_tx_desc() for bytes:
if (tp->size + bytes > msh)
bytes = msh - tp->size;
This will lead a infinite loop. So check and fail early if tp->size if
greater or equal to msh.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Cheolwoo Myung <cwmyung@snu.ac.kr>
Reported-by: Ruhr-University Bochum <bugs-syssec@rub.de>
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Currently the emulated EMAC for sun8i always traverses the transmit queue
from the head when transferring packets. It searches for a list of consecutive
descriptors whichs are flagged as ready for processing and transmits their payloads
accordingly. The controller stops processing once it finds a descriptor that is not
marked ready.
While the above behaviour works in most situations, it is not the same as the actual
EMAC in hardware. Actual hardware uses the TX_CUR_DESC register value to keep track
of the last position in the transmit queue and continues processing from that position
when software triggers the start of DMA processing. The currently emulated behaviour can
lead to packet loss on transmit when software fills the transmit queue with ready
descriptors that overlap the tail of the circular list.
This commit modifies the emulated EMAC for sun8i such that it processes
the transmit queue using the TX_CUR_DESC register in the same way as hardware.
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210310195820.21950-2-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Next batch of patches for the ppc target and machine types. Includes:
* Several cleanups for sm501 from Peter Maydell
* An update to the SLOF guest firmware
* Improved handling of hotplug failures in spapr, associated cleanups
to the hotplug handling code
* Several etsec fixes and cleanups from Bin Meng
* Assorted other fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=/uyx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210310' into staging
ppc patch queue for 2021-03-10
Next batch of patches for the ppc target and machine types. Includes:
* Several cleanups for sm501 from Peter Maydell
* An update to the SLOF guest firmware
* Improved handling of hotplug failures in spapr, associated cleanups
to the hotplug handling code
* Several etsec fixes and cleanups from Bin Meng
* Assorted other fixes and cleanups
# gpg: Signature made Wed 10 Mar 2021 04:08:53 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210310:
spapr.c: send QAPI event when memory hotunplug fails
spapr.c: remove duplicated assert in spapr_memory_unplug_request()
target/ppc: fix icount support on Book-e vms accessing SPRs
qemu_timer.c: add timer_deadline_ms() helper
spapr_pci.c: add 'unplug already in progress' message for PCI unplug
spapr.c: add 'unplug already in progress' message for PHB unplug
hw/ppc: e500: Add missing <ranges> in the eTSEC node
hw/net: fsl_etsec: Fix build error when HEX_DUMP is on
spapr_drc.c: use DRC reconfiguration to cleanup DIMM unplug state
spapr_drc.c: add hotunplug timeout for CPUs
spapr_drc.c: introduce unplug_timeout_timer
target/ppc: Fix bcdsub. emulation when result overflows
docs/system: Extend PPC section
spapr: rename spapr_drc_detach() to spapr_drc_unplug_request()
spapr_drc.c: use spapr_drc_release() in isolate_physical/set_unusable
pseries: Update SLOF firmware image
spapr_drc.c: do not call spapr_drc_detach() in drc_isolate_logical()
hw/display/sm501: Inline template header into C file
hw/display/sm501: Expand out macros in template header
hw/display/sm501: Remove dead code for non-32-bit RGB surfaces
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'running' argument from VMChangeStateHandler does not require
other value than 0 / 1. Make it a plain boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210111152020.1422021-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
"qemu-common.h" should be included to provide the forward declaration
of qemu_hexdump() when HEX_DUMP is on.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210228050431.24647-1-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
An assorted set of spelling fixes in various places.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210309111510.79495-1-mjt@msgid.tls.msk.ru>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-2-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some mlx vdpa devices with kernels at least up to 5.11 currently present
0 as their MAC address. This is because they have not been
pre-configured with a MAC: they have a learning bridge and only learn
the MAC once guest is up. Kernel patches and tools to allow programming
the MAC from host are being developed. For now - since these
combinations exist in the field - let's detect zero mac and just try to
proceed with the mac from the qemu command line.
This makes the guest use this MAC to send packets in turn teaching
the MAC to the card, and things work.
TODO:
report the actual MAC from QEMU commad line in the info message.
TODO:
detect that a (non-zero) hardware MAC does not match QEMU command line
and fail init.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20210225165506.18321-2-lulu@redhat.com>
mst: rewritten code comments, message printed and the commit log.
Cc: Eli Cohen <elic@nvidia.com>
Cc: Parav Pandit <parav@nvidia.com>
Tested-by: Adrian Moreno <amorenoz@redhat.com>
Tested-by: Sean Mooney <smooney@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In failover_add_primary(), we search the id of the failover device by
scanning the list of the devices in the opts list to find a device with
a failover_pair_id equals to the id of the virtio-net device.
If the failover_pair_id is not found, QEMU ignores the primary
device silently (which also means it will not be hidden and
it will be enabled directly at boot).
After that, we search the id in the opts list to do a qdev_device_add()
with it. The device will be always found as otherwise we had exited
before, and thus the warning is never displayed.
Fix that by moving the error report to the first exit condition.
Also add a g_assert() to be sure the compiler will not complain
about a possibly NULL pointer.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-4-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
failover_add_primary() calls qdev_device_add() and doesn't unref
the device. Because of that, when the device is unplugged a reference
is remaining and prevents the cleanup of the object.
This prevents to be able to plugin back the failover primary device,
with errors like:
(qemu) device_add vfio-pci,host=0000:41:00.0,id=hostdev0,bus=root.3,failover_pair_id=net0
(qemu) device_del hostdev0
We can check with "info qtree" and "info pci" that the device has been removed, and then:
(qemu) device_add vfio-pci,host=0000:41:00.0,id=hostdev1,bus=root.3,failover_pair_id=net0
Error: vfio 0000:41:00.0: device is already attached
(qemu) device_add vfio-pci,host=0000:41:00.0,id=hostdev0,bus=root.3,failover_pair_id=net0
qemu-kvm: Duplicate ID 'hostdev0' for device
Fixes: 21e8709b29 ("failover: Remove primary_dev member")
Cc: quintela@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-3-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Per MPC8548ERM [1] chapter 14.5.3.4.1:
When RCTRL.RSF is 1, frames less than 64 bytes are accepted upon
a DA match. But currently QEMU does the opposite. This commit
reverses the RCTRL.RSF testing logic to match the manual.
Due to the reverse of the logic, certain guests may potentially
break if they don't program eTSEC to have RCTRL.RSF bit set.
When RCTRL.RSF is 0, short frames are silently dropped, however
as of today both slirp and tap networking do not pad short frames
(e.g.: an ARP packet) to the minimum frame size of 60 bytes. So
ARP requests will be dropped, preventing the guest from becoming
visible on the network.
The same issue was reported on e1000 and vmxenet3 before, see:
commit 78aeb23ede ("e1000: Pad short frames to minimum size (60 bytes)")
commit 40a87c6c9b ("vmxnet3: Pad short frames to minimum size (60 bytes)")
[1] https://www.nxp.com/docs/en/reference-manual/MPC8548ERM.pdf
Fixes: eb1e7c3e51 ("Add Enhanced Three-Speed Ethernet Controller (eTSEC)")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <1612923021-19746-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At present net_checksum_calculate() blindly calculates all types of
checksums (IP, TCP, UDP). Some NICs may have a per type setting in
their BDs to control what checksum should be offloaded. To support
such hardware behavior, introduce a 'csum_flag' parameter to the
net_checksum_calculate() API to allow fine control over what type
checksum is calculated.
Existing users of this API are updated accordingly.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The lan9118 code mostly uses symbolic constants for register offsets;
the exceptions are those which the datasheet doesn't give an official
symbolic name to.
Add some names for the registers which don't already have them, based
on the longer names they are given in the memory map.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210108180401.2263-3-peter.maydell@linaro.org
This commit is the result of running the timer-del-timer-free.cocci
script on the whole source tree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201215154107.3255-4-peter.maydell@linaro.org
Anywhere we create a list of just one item or by prepending items
(typically because order doesn't matter), we can use
QAPI_LIST_PREPEND(). But places where we must keep the list in order
by appending remain open-coded until later patches.
Note that as a side effect, this also performs a cleanup of two minor
issues in qga/commands-posix.c: the old code was performing
new = g_malloc0(sizeof(*ret));
which 1) is confusing because you have to verify whether 'new' and
'ret' are variables with the same type, and 2) would conflict with C++
compilation (not an actual problem for this file, but makes
copy-and-paste harder).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20201113011340.463563-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
[Straightforward conflicts due to commit a8aa94b5f8 "qga: update
schema for guest-get-disks 'dependents' field" and commit a10b453a52
"target/mips: Move mips_cpu_add_definition() from helper.c to cpu.c"
resolved. Commit message tweaked.]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Instead of modifying the value member of a list element passed as a
parameter, and open-coding the manipulation of that list, it's nicer
to just return a freshly allocated value to be prepended to a list
using QAPI_LIST_PREPEND.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20201113011340.463563-3-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In order to use inclusive terminology, rename 'slave stream'
as 'sink stream'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200910070131.435543-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename 'slave stream'
as 'sink stream'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200910070131.435543-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Xilinx ZynqMP CAN controller is developed based on SocketCAN, QEMU CAN bus
implementation. Bus connection and socketCAN connection for each CAN module
can be set through command lines.
Example for using single CAN:
-object can-bus,id=canbus0 \
-machine xlnx-zcu102.canbus0=canbus0 \
-object can-host-socketcan,id=socketcan0,if=vcan0,canbus=canbus0
Example for connecting both CAN to same virtual CAN on host machine:
-object can-bus,id=canbus0 -object can-bus,id=canbus1 \
-machine xlnx-zcu102.canbus0=canbus0 \
-machine xlnx-zcu102.canbus1=canbus1 \
-object can-host-socketcan,id=socketcan0,if=vcan0,canbus=canbus0 \
-object can-host-socketcan,id=socketcan1,if=vcan0,canbus=canbus1
To create virtual CAN on the host machine, please check the QEMU CAN docs:
https://github.com/qemu/qemu/blob/master/docs/can.txt
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Message-id: 1605728926-352690-2-git-send-email-fnu.vikram@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only three uses remained, and we can remove them on that case.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-28-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can calculate device just once.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-27-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pass it as an argument.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-26-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-25-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
So we can calculate the device id when we need it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-24-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It can never give one error.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-23-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We check that it exist at device creation time, so we don't have to
check anywhere else.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-22-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit:
* Rename them to failover_find_primary_devices() so
- it starts with failover_
- it don't connect anything, just find the primary device
* Create documentation for the function
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-19-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It just calls virtio_net_find_primary(), so just update the callers.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-18-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
You should not use pasive.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-17-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We didn't use at all the -1 value, and we don't really care. It was
only used for the cases when this is not the device that we are
searching for. And in that case we should not hide the device.
Once there, simplify virtio-Snet_primary_should_be_hidden.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-16-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
a - is_my_primary() never sets one error
b - If we return 1, primary_device_id is always set
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-15-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Two things, at this point:
* n->primary_device_id has to be set, otherwise
virtio_net_find_primary don't work. So we have a leak here.
* it has to be exactly the same that prim_dev->id because what
qdev_find_recursive() does is just compare this two values.
So remove the unneeded assignment and leaky bits.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-14-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was only used once. And we have there opts->id, so no need for it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-13-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can calculate it, and we only use it once anyways.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-12-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was really only used once, in failover_add_primary(). Just search
for it on global opts when it is needed.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-11-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-10-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
You should not use passive naming variables.
And once there, be able to search for them.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-9-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Never both.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-8-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was only set "once", and with the wrong value. As far as I can see,
libvirt still don't use it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-7-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-6-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Just remove the struct member.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-5-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-4-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Once there, remove not needed cast.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-3-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
