When calling qemu_system_reset after startup on a Cortex-M
CPU, the initial values of PC, MSP and the Thumb bit weren't being set
correctly if the vector table was in ROM. In particular, since Thumb was 0, a
Usage Fault would arise immediately after trying to execute any instruction
on a Cortex-M.
Signed-off-by: Martin Galvan <martin.galvan@tallertechnologies.com>
Message-id: CAOKbPbaLt-LJsAKkQdOE0cs9Xx4OWrUfpDhATXPSdtuNw2xu_A@mail.gmail.com
[PMM: removed an incorrect comment]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the missing input interrupt logic to the pl061 GPIO device. To
keep the floating output pins to stay high, the old state variable had to be
split into two separate ones for input and output - which brings the vmstate
version to 3.
Edge level interrupts and I/O were tested under Linux 3.14. Level interrupt
handling hasn't been tested.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Message-id: 54024FD2.9080204@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Correct an error in the logic for deciding whether we can
take an IRQ interrupt which meant that on M profile cores
it was never possible to disable them.
The design here is still bogus in that M profile doesn't
have separate "IRQ" and "FIQ", which are an A/R profile
concept; we should ideally implement the proper priority
based scheme.
Signed-off-by: David Hoover <spm@boiteauxlettres.sent.at>
[PMM: Wrote a proper commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a property "linux,stdout-path" to the /chosen DT node and make
it point to the emulated UART. This allows users such as the Linux
kernel to produce console output without the need to pass console=
or earlycon=pl011,0x... command line arguments.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1409317439-29349-1-git-send-email-ard.biesheuvel@linaro.org
Reviewed-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Increase the clock step to avoid Travis failure in some builds due to
overagressive timeout.
Signed-off-by: Marc Marí <marc.mari.barcelo@gmail.com>
Message-id: 1410428416-5046-1-git-send-email-marc.mari.barcelo@gmail.com
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make sure to pass the correct fd via SCM_RIGHTS in socket_scm_helper.c
(i.e. fd_to_send, not socket-fd).
Signed-off-by: Stratos Psomadakis <psomas@grnet.gr>
Signed-off-by: Dimitris Aragiorgis <dimara@grnet.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For some device models, the guest can prevent unplug. Some users need a
way to forcibly revoke device model access to the block backend then, so
the underlying images can be safely used for something else.
drive_del lets you do that. Unfortunately, it conflates revoking access
with destroying the backend.
Commit 9063f81 made drive_del immediately destroy the root BDS. Nice:
the device name becomes available for reuse immediately. Not so nice:
the device model's pointer to the root BDS dangles, and we're prone to
crash when the memory gets reused.
Commit d22b2f4 fixed that by hiding the root BDS instead of destroying
it. Destruction only happens on unplug. "Hiding" means removing it
from bdrv_states and graph_bdrv_states; see bdrv_make_anon().
This "destroy on revoke" is a misfeature we don't want to carry
forward to blockdev-add, just like "destroy on unplug" (commit
2d246f0). So make drive_del fail on anything added with blockdev-add.
We'll add separate QMP commands to revoke device model access and to
destroy backends.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BLOCK_IO_ERROR events are logged by libvirt, which helps with
post mortem analysis of guests. However, one information that
we miss today is a human readable string describing the cause
of the I/O error.
This commit adds that string it to BLOCK_IO_ERROR. Note that
this string is a debugging aid for humans, meaning that it
should not parsed by applications.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 3718d8ab65 ("block: Replace in_use
with operation blocker") broke the error path because it consumed
local_err instead of propagating it.
The caller has no way to know that the function failed. This caused
virtio-blk to start "successfully" even though there was a fatal
dataplane error.
Steps to reproduce:
$ qemu-system-x86_64 -enable-kvm -object iothread,id=iothread0 \
-drive if=none,id=drive0,file=a.img \
(qemu) drive_mirror drive0 /tmp/foo.img
(qemu) device_add virtio-blk-pci,iothread=iothread0,drive=drive0
Expected result:
Since the mirror block job is using drive0 it is not possible to start
virtio-blk data-plane.
device_add fails and the PCI adapter is not added.
Actual result:
device_add completes and the PCI adapter is added.
Cc: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch initializes monitor for gdbstub with the qemu_chr_alloc function
instead of just allocating the memory. Initialization function call
is required, because it also creates chr_write_lock mutex, which is used
when writing to this character device.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds outport to VMState to allow correct saving and restoring
the state of PC keyboard controller.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds irq_reinject_on_ack_count field to VMState to allow correct
saving/loading the state of MC146818 RTC.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch avoids setting an irq while loading the state of the ISA bridge.
Because the i8259 has not been deserialized yet, raising an interrupt
could bring the system out-of-sync with the migration source. For example,
the migration source could have masked the interrupt in the i8259. On the
destination, the i8259 device model would not know that yet and would
trigger an interrupt in the CPU.
This patch eliminates setting the irq and just restores the calculated
state fields in post_load function. Interrupt state will be deserialized
separately through the IRR field of the i8259.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some fields were added to VMState by this patch to preserve correct
loading of the serial port controller state.
Updating FCR value while loading was also modified to disable generating
an interrupt by loadvm.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMState added by this patch preserves correct
loading of the parallel port controller state.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMState added by this patch preserves correct
loading of the FDC device state.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ticks and clock offset used by CPU timers have to be saved in vmstate.
But vmstate for these fields registered only in icount mode.
Missing registration leads to breaking the continuity when vmstate is loaded.
This patch introduces new initialization function which fixes this.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch postpones vapic_paddr initialization, which is performed
during migration. When vapic_paddr is synchronized within the migration
process, apic_common functions could operate with incorrect apic state,
if it hadn't loaded yet. This patch postpones the synchronization until
the virtual machine is started, ensuring that the whole virtual machine
state has been loaded.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Tested-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Run resize grow test to ensure that existing data
is not lost during grow and new space is zeroed.
Signed-off-by: Chrysostomos Nanakos <cnanakos@grnet.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is the next step for decoupling block accounting functions from
BlockDriverState.
In a future commit the BlockAcctStats structure will be moved from
BlockDriverState to the device models structures.
Note that bdrv_get_stats was introduced so device models can retrieve the
BlockAcctStats structure of a BlockDriverState without being aware of it's
layout.
This function should go away when BlockAcctStats will be embedded in the device
models structures.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: John Snow <jsnow@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>
CC: Max Reitz <mreitz@redhat.com>
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The middle term goal is to move the BlockAcctStats structure in the device models.
(Capturing I/O accounting statistics in the device models is good for billing)
This patch make a small step in this direction by removing a reference to BDRV.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>i
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The plan is to add new accounting metrics (latency, invalid requests, failed
requests, queue depth) and block.c is overpopulated so it will be better to work
in a separate module.
Moreover the long term plan is to have statistics in each of the BDS of the graph
for metrology purpose; this means that the device model statistics must move from
the topmost BDS to the device model.
So we need to decouple the statistic code from BlockDriverState.
This is another argument for the extraction of the code in a separate module.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Benoit Canet <benoit@irqsave.net>
CC: Fam Zheng <famz@redhat.com>
CC: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Extract the block accounting statistics into a structure so the block device
models can hold them in the future.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Eric Blake <eblake@redhat.com>
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Set the IDE MMIO memory type to little endian. The ATA specs identify
words part of the control commands encoded as little endian.
While this has no impact on little endian systems, it's required for big
endian systems(eg OpenRisc).
Signed-off-by: Valentin Manea <valentin.manea@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Dragging block_int.h into a header is *not* nice. Fortunately, this
is the only offender.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The Error object was leaked after failed bdrv_new(). While there,
streamline control flow a bit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 6db9560 split off the growable case so it can use
bdrv_file_open() instead of bdrv_open() then. Growable BDSes become
anonymous. Weird.
Commit 2e40134 folded bdrv_file_open() back into bdrv_open() with new
flag BDRV_O_PROTOCOL. We still have two bdrv_open() calls, and
growable BDSes remain anonymous.
Circle back to before commit 6db9560: just one call, not anonymous.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
cpu_to_be32() is wrong since vhd_type is an enum constant
(just a regular CPU-endian integer).
Signed-off-by: Xiaodong Gong <gordongong0350@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Management software, such as RHEV's vdsm, want to be able to allocate
disk space on demand. The basic use case is to start a VM with a small
disk and then the disk is enlarged when QEMU hits a ENOSPC condition.
To this end, the management software has to be notified when QEMU
encounters ENOSPC. The solution implemented by this commit is simple:
it extends the BLOCK_IO_ERROR with a 'nospace' key, which is true
when QEMU is stopped due to ENOSPC.
Note that support for querying this event is already present in
query-block by means of the 'io-status' key. Also, the new 'nospace'
BLOCK_IO_ERROR field shares the same semantics with 'io-status',
which basically means that werror= has to be set to either
'stop' or 'enospc' to enable 'nospace'.
Finally, this commit also updates the 'io-status' key doc in the
schema with a list of supported device models.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add back the PCIe config capabilities on XHCI cards in non-PCIe slots,
but only for machine types before 2.1.
This fixes a migration incompatibility in the XHCI PCI devices
caused by:
058fdcf52c - xhci: add endpoint cap on express bus only
Note that in fixing it for compatibility with older QEMUs, it breaks
compatibility with existing QEMU 2.1's on older machine types.
The status before this patch was (if it used an XHCI adapter):
machine type | source qemu
any pre-2.1 - FAIL
any 2.1... - PASS
With this patch:
machine type | source qemu
any pre-2.1 - PASS
pre-2.1 2.1... - FAIL
2.1 2.1... - PASS
A test to trigger it is to add '-device nec-usb-xhci,id=xhci,addr=0x12'
to the command line.
Cc: qemu-stable@nongnu.org
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add parameter errp to gethugepagesize thus callers can handle errors.
If user adds a memory-backend-file object using object_add command,
specifying a non-existing directory for property mem-path, qemu will
core dump with message:
/nonexistingdir: No such file or directory
Bad ram offset fffffffffffff000
Aborted (core dumped)
This patch fixes the problem. With this patch, qemu reports an error
message like:
qemu-system-x86_64: -object memory-backend-file,mem-path=/nonexistingdir,id=mem-file0,size=128M:
failed to get page size of file /nonexistingdir: No such file or directory
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Report an error when memory < hpagesize in file_ram_alloc() so callers
can handle the error.
If user adds a memory-backend-file object using object_add command,
specifying a size that is less than huge page size, qemu will core dump
with message:
Bad ram offset fffffffffffff000
Aborted (core dumped)
This patch fixes the problem. With this patch, qemu reports error
message like:
qemu-system-x86_64: -object memory-backend-file,mem-path=/hugepages,id=mem-file0,size=1M: memory
size 0x100000 must be equal to or larger than huge page size 0x200000
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When using monitor command object_add to add a memory backend whose
size is way too big to allocate memory for it, qemu just exits. In
the case we'd better give an error message and keep guest running.
The problem can be reproduced as follows:
1. run qemu
2. (monitor)object_add memory-backend-ram,size=100000G,id=ram0
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add parameter errp to memory_region_init_rom_device and update all call
sites to propagate the error.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[Propagate the error out of realize. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add parameter errp to memory_region_init_ram and update all call sites
to pass in &error_abort.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add parameter errp to qemu_ram_alloc and qemu_ram_alloc_from_ptr so that
we can handle errors.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[Assert ptr != NULL in memory_region_init_ram_ptr. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes an issue with module build system. block/iscsi.so is
currently broken:
$ ~/build/last/qemu-img
Failed to open module: /home/fam/build/master/block-iscsi.so:
undefined symbol: qmp_query_uuid
qemu-img: Not enough arguments
Try 'qemu-img --help' for more information
To fix this, we should (at least) let qemu-img link qmp_query_uuid from
libqemustub.a. (There are a few other symbols missing, as well.)
This patch changes the linking rules to:
1) Build ".mo" with "ld -r -o $@ $^" for each ".so", and later build .so
with it.
2) Always build all the .mo before linking the executables. This is
achieved by adding those .mo files to the executables' "-y"
variables.
3) When linking an executable, those .mo files in its "-y" variables are
filtered out, and replaced by one or more -Wl,-u,$symbol flags. This
is done in the added macro "process-archive-undefs".
These "-Wl,-u,$symbol" flags will force ld to pull in the function
definition from the archives when linking.
Note that the .mo objects, that are actually meant to be linked in
the executables, are already expanded in unnest-vars, before the
linking command. So we are safe to simply filter out .mo for the
purpose of pulling undefined symbols.
process-archive-undefs works as this: For each ".mo", find all the
undefined symbols in it, filter ones that are defined in the
archives. For each of these symbols, generate a "-Wl,-u,$symbol" in
the link command, and put them before archive names in the command
line.
Suggested-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
So that we won't have an empty getauxval.o which is disliked by ranlib.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In any other cases the object file is effectively empty, which is
disliked by ranlib and nm on Mac OS X.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Just go to the internal error runstate. This lets you use the "x",
"dump-guest-memory" or "info register" commands.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both OpenBSD and FreeBSD SPARC64 attempt to read the interrupt map from the
hardware and will fail if the correct ino isn't present.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Alexander Graf (11):
PPC: KVM: Fix g3beige and mac99 when HV is loaded
PPC: mac99: Move NVRAM to page boundary when necessary
KVM: Add helper to run KVM_CHECK_EXTENSION on vm fd
PPC: KVM: Use vm check_extension for pv hcall
PPC: mac99: Fix core99 timer frequency
PPC: mac_nvram: Remove unused functions
PPC: mac_nvram: Allow 2 and 4 byte accesses
PPC: mac_nvram: Split NVRAM into OF and OSX parts
PPC: Mac: Move tbfreq into local variable
PPC: Cuda: Use cuda timer to expose tbfreq to guest
PPC: Fix default config ordering and add eTSEC for ppc64
Alexey Kardashevskiy (7):
spapr: Move DT memory node rendering to a helper
spapr: Use DT memory node rendering helper for other nodes
spapr: Refactor spapr_populate_memory() to allow memoryless nodes
spapr: Split memory nodes to power-of-two blocks
spapr: Add a helper for node0_size calculation
spapr: Fix ibm, associativity for memory nodes
spapr_pci: Fix config space corruption
Anton Blanchard (2):
spapr-vlan: Don't touch last entry in buffer list
hypervisor property clashes with hypervisor node
Benjamin Herrenschmidt (2):
loader: Add load_image_size() to replace load_image()
spapr: Locate RTAS and device-tree based on real RMA
Bharat Bhushan (4):
ppc: debug stub: Get trap instruction opcode from KVM
ppc: synchronize excp_vectors for injecting exception
ppc: Add software breakpoint support
ppc: Add hw breakpoint watchpoint support
Gonglei (1):
spapr: fix possible memory leak
Greg Kurz (1):
spapr_pci: map the MSI window in each PHB
Nikunj A Dadhania (3):
ppc: spapr-rtas - implement os-term rtas call
spapr: add uuid/host details to device tree
ppc/spapr: Fix MAX_CPUS to 255
Peter Maydell (1):
hw/ppc/spapr_hcall.c: Fix typo in function names
Tom Musta (20):
linux-user: Fix Stack Pointer Bug in PPC setup_rt_frame
linux-user: Split PPC Trampoline Encoding from Register Save
linux-user: Enable Signal Handlers on PPC64
linux-user: Properly Dereference PPC64 ELFv1 Signal Handler Pointer
linux-user: Implement do_setcontext for PPC64
linux-user: Handle PPC64 ELFv2 Function Pointers
target-ppc: Bug Fix: rlwinm
target-ppc: Bug Fix: rlwnm
target-ppc: Bug Fix: rlwimi
target-ppc: Bug Fix: mullwo
target-ppc: Bug Fix: mullw
target-ppc: Bug Fix: mulldo OV Detection
target-ppc: Bug Fix: srawi
target-ppc: Bug Fix: srad
target-ppc: Special Case of rlwimi Should Use Deposit
target-ppc: Optimize rlwinm MB=0 ME=31
target-ppc: Optimize rlwnm MB=0 ME=31
target-ppc: Clean Up mullw
target-ppc: Clean up mullwo
target-ppc: Implement mulldo with TCG
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=lpcC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/agraf/tags/signed-ppc-for-upstream' into staging
Patch queue for ppc - 2014-09-08
Alexander Graf (11):
PPC: KVM: Fix g3beige and mac99 when HV is loaded
PPC: mac99: Move NVRAM to page boundary when necessary
KVM: Add helper to run KVM_CHECK_EXTENSION on vm fd
PPC: KVM: Use vm check_extension for pv hcall
PPC: mac99: Fix core99 timer frequency
PPC: mac_nvram: Remove unused functions
PPC: mac_nvram: Allow 2 and 4 byte accesses
PPC: mac_nvram: Split NVRAM into OF and OSX parts
PPC: Mac: Move tbfreq into local variable
PPC: Cuda: Use cuda timer to expose tbfreq to guest
PPC: Fix default config ordering and add eTSEC for ppc64
Alexey Kardashevskiy (7):
spapr: Move DT memory node rendering to a helper
spapr: Use DT memory node rendering helper for other nodes
spapr: Refactor spapr_populate_memory() to allow memoryless nodes
spapr: Split memory nodes to power-of-two blocks
spapr: Add a helper for node0_size calculation
spapr: Fix ibm, associativity for memory nodes
spapr_pci: Fix config space corruption
Anton Blanchard (2):
spapr-vlan: Don't touch last entry in buffer list
hypervisor property clashes with hypervisor node
Benjamin Herrenschmidt (2):
loader: Add load_image_size() to replace load_image()
spapr: Locate RTAS and device-tree based on real RMA
Bharat Bhushan (4):
ppc: debug stub: Get trap instruction opcode from KVM
ppc: synchronize excp_vectors for injecting exception
ppc: Add software breakpoint support
ppc: Add hw breakpoint watchpoint support
Gonglei (1):
spapr: fix possible memory leak
Greg Kurz (1):
spapr_pci: map the MSI window in each PHB
Nikunj A Dadhania (3):
ppc: spapr-rtas - implement os-term rtas call
spapr: add uuid/host details to device tree
ppc/spapr: Fix MAX_CPUS to 255
Peter Maydell (1):
hw/ppc/spapr_hcall.c: Fix typo in function names
Tom Musta (20):
linux-user: Fix Stack Pointer Bug in PPC setup_rt_frame
linux-user: Split PPC Trampoline Encoding from Register Save
linux-user: Enable Signal Handlers on PPC64
linux-user: Properly Dereference PPC64 ELFv1 Signal Handler Pointer
linux-user: Implement do_setcontext for PPC64
linux-user: Handle PPC64 ELFv2 Function Pointers
target-ppc: Bug Fix: rlwinm
target-ppc: Bug Fix: rlwnm
target-ppc: Bug Fix: rlwimi
target-ppc: Bug Fix: mullwo
target-ppc: Bug Fix: mullw
target-ppc: Bug Fix: mulldo OV Detection
target-ppc: Bug Fix: srawi
target-ppc: Bug Fix: srad
target-ppc: Special Case of rlwimi Should Use Deposit
target-ppc: Optimize rlwinm MB=0 ME=31
target-ppc: Optimize rlwnm MB=0 ME=31
target-ppc: Clean Up mullw
target-ppc: Clean up mullwo
target-ppc: Implement mulldo with TCG
# gpg: Signature made Mon 08 Sep 2014 11:51:15 BST using RSA key ID 03FEDC60
# gpg: Can't check signature: public key not found
* remotes/agraf/tags/signed-ppc-for-upstream: (52 commits)
hypervisor property clashes with hypervisor node
PPC: Fix default config ordering and add eTSEC for ppc64
spapr_pci: map the MSI window in each PHB
target-ppc: Implement mulldo with TCG
target-ppc: Clean up mullwo
target-ppc: Clean Up mullw
target-ppc: Optimize rlwnm MB=0 ME=31
target-ppc: Optimize rlwinm MB=0 ME=31
target-ppc: Special Case of rlwimi Should Use Deposit
spapr-vlan: Don't touch last entry in buffer list
spapr_pci: Fix config space corruption
PPC: Cuda: Use cuda timer to expose tbfreq to guest
PPC: Mac: Move tbfreq into local variable
PPC: mac_nvram: Split NVRAM into OF and OSX parts
PPC: mac_nvram: Allow 2 and 4 byte accesses
PPC: mac_nvram: Remove unused functions
PPC: mac99: Fix core99 timer frequency
PPC: KVM: Use vm check_extension for pv hcall
KVM: Add helper to run KVM_CHECK_EXTENSION on vm fd
target-ppc: Bug Fix: srad
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
