Recent PowerPC kernel end up in kernel panic during boot in -nographic
mode. In this mode the second serial port is used as the udbg console,
and thus a few characters are sent on this port. This activates the
tx interrupt flag, and later choke the Linux kernel, as it was not
expecting such a flag to be set.
The problem here comes from the fact that contrary to most devices the
interrupt flags are only set if the interrupt is enabled. Quoting the
datasheet: "If the corresponding IE bit is not set, the IP for that
source of interrupt will never be set."
This patch fixes that by enabling the interrupt flag only when the
corresponding interrupt is enabled.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As stated before, devices can be little, big or native endian. The
target endianness is not of their concern, so we need to push things
down a level.
This patch adds a parameter to cpu_register_io_memory that allows a
device to choose its endianness. For now, all devices simply choose
native endian, because that's the same behavior as before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
According to scc_escc_um.pdf:
- Reset Highest IUS must update irq status to allow processing
of the next priority interrupt.
- rx interrupt has always higher priority than tx on same channel
The documentation only explicitly says that Reset Highest IUS
command (0x38) clears IUS bits, not that it clears the corresponding
interrupt too, so don't clear interrupts on this command.
The patch allows SunOS 4.1.4 to use the serial ports
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Like qdev_init(), but terminate program via hw_error() instead of
returning an error value.
Use it instead of qdev_init() where terminating the program on failure
is okay, either because it's during machine construction, or because
we know that failure can't happen.
Because relying in the latter is somewhat unclean, and the former is
not always obvious, it would be nice to go back to qdev_init() in the
not-so-obvious cases, only with proper error handling. I'm leaving
that for another day, because it involves making sure that error
values are properly checked by all callers.
Patchworks-ID: 35168
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix another place with =- to be "= -".
to avoid confusion with old-style "-="
(which we also have, and needs to be fixed).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Put space between = and - assigning a negative number
to avoid confusion with old-style "-="
(which we also have, and needs to be fixed).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Sorry folks, but it has to be. One more of these invasive qdev patches.
We have a serious design bug in the qdev interface: device init
callbacks can't signal failure because the init() callback has no
return value. This patch fixes it.
We have already one case in-tree where this is needed:
Try -device virtio-blk-pci (without drive= specified) and watch qemu
segfault. This patch fixes it.
With usb+scsi being converted to qdev we'll get more devices where the
init callback can fail for various reasons.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch is a major overhaul of the device properties. The properties
are saved directly in the device state struct now, the linked list of
property values is gone.
Advantages:
* We don't have to maintain the list with the property values.
* The value in the property list and the value actually used by
the device can't go out of sync any more (used to happen for
the pci.devfn == -1 case) because there is only one place where
the value is stored.
* A record describing the property is required now, you can't set
random properties any more.
There are bus-specific and device-specific properties. The former
should be used for properties common to all bus drivers. Typical
use case is bus addressing, i.e. pci.devfn and i2c.address.
Properties have a PropertyInfo struct attached with name, size and
function pointers to parse and print properties. A few common property
types have PropertyInfos defined in qdev-properties.c. Drivers are free
to implement their own very special property parsers if needed.
Properties can have default values. If unset they are zero-filled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The parameter is always zero except when registering the three internal
io regions (ROM, unassigned, notdirty). Remove the parameter to reduce
the API's power, thus facilitating future change.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add the parameter 'order' to qemu_register_reset and sort callbacks on
registration. On system reset, callbacks with lower order will be
invoked before those with higher order. Update all existing users to the
standard order 0.
Note: At least for x86, the existing users seem to assume that handlers
are called in their registration order. Therefore, the patch preserves
this property. If someone feels bored, (s)he could try to identify this
dependency and express it properly on callback registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The Z85C30 on the PowerMAC machines have one interrupt per serial
channel, while the Sparc machines have only one for both. Allow the
emulated device to use one IRQ per channel.
Patch by Laurent Vivier.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6295 c046a42c-6fe2-441c-8c8c-71466251a162
Swap the two CharDriverState arguments so that the first argument
corresponds to the channel A and the second argument to the channel B.
Modify hw/sun4m.c accordingly.
This fixes the order of the serial ports on the PPC machines.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6284 c046a42c-6fe2-441c-8c8c-71466251a162
