Factor out disconnect code (called when a device disappears) to a
separate function. Add a check for ENODEV errno to a few more places
to make sure we notice disconnects.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch removes all references to signal.h when qemu-common.h is included
as they become redundant.
Signed-off-by: Alexandre Raymond <cerbere@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Remove the cancel callback from the USBPacket struct, move it over
to USBDeviceInfo. Zap usb_defer_packet() which is obsolete now.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Calculate the max packet size correctly. Only bits 0..11 specify the size,
bits 11+12 specify the number of (highspeed) microframes the endpoint wants
to use.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add support for splitting large transfers into multiple smaller ones.
This is needed for the upcoming EHCI emulation which allows guests
to submit requests up to 20k in size. The linux kernel allows 16k
max size though.
Based on a patch from David Ahern, see
http://www.mail-archive.com/qemu-devel@nongnu.org/msg30337.html
Cc: David Ahern <daahern@cisco.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Lookup async urbs which are to be canceled using the linked list
instead of the direct opaque pointer. There are two reasons we
are doing that: First, to avoid the opaque poiner to the callback,
which is needed for upcoming cleanups. Second, because we might
need multiple urbs per request for highspeed support, so a single
opaque pointer doesn't cut it any more anyway.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds code to track all async urbs in a linked list,
so we can find them without having to pass around a opaque
pointer to them. Prerequisite for the cleanups.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds a hostport property which allows to specify the host usb
devices to pass through by bus number and physical port. This means you
can basically hand over one (or more) of the usb plugs on your host to
the guest and whatever device is plugged in there will show up in the
guest.
Usage:
-device usb-host,hostbus=1,hostport=1
You can figure the port numbers by plugging in some usb device, then
find it in "info usbhost" and pick bus and port specified there.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The device path isn't just a number. It specifies the physical port
the device is connected to and in case the device is connected via
usb hub you'll have two numbers there, like this: "5.1". The first
specifies the root port where the hub is plugged into, the second
specifies the port number of the hub where the device is plugged in.
With multiple hubs chained the string can become longer.
This patch renames devpath to port and makes it a string. It also
adapts the sysfs parsing code accordingly. The parser code is also more
strict now and skips the root hubs (which can't be assigned anyway).
The "info usbhost" monitor command now prints bus number, (os-assigned)
device address and physical port for each device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Make the linux usb host passthrough code use the usb_generic_handle_packet()
function, rather then the curent DYI code. This removes 200 lines of almost
identical code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
cppcheck report:
usb-linux.c:661: warning: Redundant assignment of "len" in switch
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Extend the iso buffering code to also buffer iso out packets, this
fixes for example using usb speakers with usb redirection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently we reserve room for endpoint data for 16 endpoints, but given
that we only use endpoint data for endpoints 1-15, and always index the
array with the endpoint-number - 1, 15 is enough.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Refuse iso usb packets when then max packet size for the endpoint is 0,
this avoids an abort in usb_host_alloc_iso() caused by trying to qemu_malloc
a 0 bytes large buffer.
If an endpoint is not in the usb descriptor we've no idea what kind of
endpoint it is and thus how to handle it, refuse packages in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently we are submitting iso packets to the host one at a time, as we
receive them from the emulated host controller. This has 2 problems:
1) If we were fast enough to submit every packet in time for the next host host
controller usb frame, we would be generating 1000 hardware interrupts per
second on the host
2) We are not fast enough to submit every packet in time for the next host host
controller usb frame, causing us to not submit iso urbs in some usb frames
which causes devices with an endpoint with an interval of 1 ms (so every
frame) to loose data. This causes for example ubs-1.1 webcams to not work
properly (usb-2.0 is not supported at all atm).
This patch fixes both problems by changing the iso packet pass through handling
to buffer packets. This version only does so for iso input packets (webcams,
audio in) I'm working on a second patch extending this to iso output packets
(audio out).
This patch makes use of the linux batching of iso packets in one urb.
When an iso in packet gets received from the emulated host controller,
it immediately submits 3 urbs with 32 iso in packets each. This causes
the host to only get an hw interrupt every 32 packets dropping the
interrupt rate to 32 interrupts per second and gives it a queue of urbs
to work from once the first 32 iso in packets have been received to make sure
no packets are dropped.
Besides submitting a whole bunch or urbs as soon as the first urb is
received, effectively creating a buffer inside the kernel, this patch also
gets rid of the asynchroneous completion for iso in urbs. Instead they are
only marked as complete in the fd write callback (which usbfs uses to signal
complete urbs). These complete packets then get consumed by returning them
synchroneously to the emulated host controller when it submits an iso in
packet for the ep in question. When no complete packets are ready (which
happens when the stream is starting) a 0 length packet gets returned to
the emulated host controller.
With this patch I've several usb-1.1 webcams working well with usb pass
through, where as without this patch none of them work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
At least one device I have lies when receiving a USB_REQ_GET_INTERFACE,
always returning 0 even if the alternate setting is different. This is
likely caused because in practice this control message is never used as
the operating system's usb stack knows which alternate setting it has
told the device to get into, and thus this ctrl message does not get
tested by device manufacturers.
When usb_fs_type == USB_FS_SYS, the active alt. setting can be read directly
from sysfs, which allows using this device through qemu's usb redirection.
More in general it seems a good idea to not send needless control msg's to
devices, esp. as the code in question is called every time a set_interface
is done. Which happens multiple times during virtual machine startup, and
when device drivers are activating the usb device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The next patch in this series introduces multiple ways to get the
alt setting dependent upon usb_fs_type, it is cleaner to put this
into its own function.
Note that this patch also changes the assumed alt setting in case
of an error getting the alt setting to be 0 (a sane default) rather
then the interface numberwhich makes no sense.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This isn't used, but leaving it empty causes valgrind noise.
Signed-off-by: Brad Hards <bradh@frogmouth.net>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
This was done with:
sed -i '/get_clock\>.*rt_clock/s/get_clock\>/get_clock_ms/' \
$(git grep -l 'get_clock\>.*rt_clock' )
sed -i '/new_timer\>.*rt_clock/s/new_timer\>/new_timer_ms/' \
$(git grep -l 'new_timer\>.*rt_clock' )
after checking that get_clock and new_timer never occur twice
on the same line. There were no missed occurrences; however, even
if there had been, they would have been caught by the compiler.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some devices seem to choke on receiving a USB_REQ_GET_CONFIGURATION ctrl msg
(witnessed with a digital picture frame usb id 1908:1320).
When usb_fs_type == USB_FS_SYS, the active configuration can be read directly
from sysfs, which allows using this device through qemu's usb redirection.
More in general it seems a good idea to not send needless control msg's to
devices, esp. as the code in question is called every time a set_interface
is done. Which happens multiple times during virtual machine startup, and
when device drivers are activating the usb device.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The next patch in this series introduces multiple ways to get the
configuration dependent upon usb_fs_type, it is cleaner to put this
into its own function.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This allows us to recreate the sysfspath used during scanning later
(which will be used in a later patch in this series).
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 3c9c706c3b.
This breaks build (gcc 4.3.2):
CC usb-linux.o
cc1: warnings being treated as errors
/src/qemu/usb-linux.c: In function 'usb_linux_update_endp_table':
/src/qemu/usb-linux.c:759: error: 'type' may be used uninitialized in
this function
Reported-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The monitor_printf() reports failure. Printing is wrong, because the
caller tries various arguments, and expects the function to fail for
some or all.
Disabled since commit 26a9e82a. Remove it.
The WLAN USB stick ZyXEL NWD271N (0586:3417) uses very large
usb control transfers of more than 2048 bytes which won't fit
into the buffer of the ctrl_struct. This results in an error message
"husb: ctrl buffer too small" and a non-working device.
Increasing the buffer size to 8192 seems to be a safe choice.
Signed-off-by: Christian Krause <chkr@plauener.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
CC usb-linux.o
cc1: warnings being treated as errors
usb-linux.c: In function 'usb_host_read_file':
usb-linux.c:1204: error: ignoring return value of 'fgets', declared with attribute warn_unused_result
make: *** [usb-linux.o] Error 1
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since commit 747bbdf7 QEMU_WARN_UNUSED_RESULT is never defined as it is
conditional on a define from config-host.h which is included only later.
Include that file earlier to get the warnings back.
Reactivating it unfortunately leads to some warnings about unused qdev_init
results. These calls are changed to qdev_init_nofail to avoid build failures.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Device names with whitespace require quoting in the shell and in the
monitor. Some of the offenders are also overly long. Some have a
more convenient alias, some don't.
The place for verbose device names is DeviceInfo member desc. The
name should be short & sweet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Using the qdev name for the product description makes for inconvenient
qdev names.
Put the product description in new USBDeviceInfo member product_desc.
Make usb_qdev_init() use it. No user or guest visible change, since
the value is still the same.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It's not a device name, it's the USB product description string.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Commit 26a9e82a has the following flaws:
* It enabled DEBUG.
* It referenced two properties by the wrong name in
usb_host_device_open(), which crashes with "qdev_prop_set: property
"USB Host Device.bus" not found".
* It broke "-usbdevice host:auto:..." by calling parse_filter()
incorrectly.
* It broke parsing of "-usbdevice host:BUS.ADDR" and "-usbdevice
host:VID:PRID" with a trivial pasto.
* It broke wildcards in "-usbdevice host:auto:...". Before, the four
filter components were stored as int, and the wildcard was encoded
as -1. The faulty commit changed storage to uint32_t, and the
wildcard encoding to 0. But it failed to update parse_filter()
accordingly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
* We don't create/delete devices, we attach/detach them instead.
* The separate autofilter list is gone, we simply walk the list
of devices directly instead.
* Autofiltering is done unconditionally now. Non-auto device scan
code got dropped.
* Autofiltering turns off the timer if there is nothing to do, it
runs only in case there are unattached host devices.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
0) This is an attempt to get an issue in usb-linux.c, for which a patch
was posted about a year ago, finally fixed.
1) Mark Burkley submitted a "EHCI emulation module" for review in in
October 2008 (see:
http://lists.gnu.org/archive/html/qemu-devel/2008-10/msg01326.html). No
EHCI emulation module was ever committed to qemu.
2) Part of that (large) patch was a fix for a separate issue in
usb-linux.c. Max Krasnyansky has ACK'ed that fix (see:
http://lists.gnu.org/archive/html/qemu-devel/2008-11/msg00032.html).
3) I already asked whether this fix was ready to be committed in last
April (see:
http://lists.gnu.org/archive/html/qemu-devel/2009-04/msg01763.html)
4) Maybe submitting this fix as a separate patch (with a really long
commit message but without a Signed-off-by) and cc-ing everbody involved
will help if actually getting this issue fixed.
Paul Bolle
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
But do so only where it may actually fail. Leave the rest for the
next commit.
Patchworks-ID: 35167
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Commit 22f84e73 added a qdev_init() missing on the path through
usb_host_device_open(), but that broke the path through
usb_host_auto_scan(), which already had one. Remove that one.
Patchworks-ID: 35169
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
* Re-add the 'dev->fd = fd;' line which the qdev patches dropped
by mistake.
* call qdev_init() so the newly created usb device is plugged into
a usb port and thus actually visible to the guest.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
In usb-linux.c:usb_host_handle_control, we pass a 1024-byte buffer and
length to the kernel. However, the length was provided by the caller
of dev->handle_packet, and is not checked, so the kernel might provide
too much data and overflow our buffer.
For example, hw/usb-uhci.c could set the length to 2047.
hw/usb-ohci.c looks like it might go up to 4096 or 8192.
This causes a qemu crash, as reported here:
http://www.mail-archive.com/kvm@vger.kernel.org/msg18447.html
This patch increases the usb-linux.c buffer size to 2048 to fix the
specific device reported, and adds a check to avoid the overflow in
any case.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move usb code from vl.c to usb-bus.c and make it use the new data
structures added by qdev conversion. qemu usb core should be able
to handle multiple USB busses just fine now (untested though).
Kill some usb_*_init() legacy functions, use usb_create_simple()
instead.
Kill some FIXMEs added by the first qdev/usb patch.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
