QEMU includes some models of old Arm machine types which are
a bit problematic for us because:
* they're written in a very old way that uses numerous APIs that we
would like to get away from (eg they don't use qdev, they use
qemu_system_reset_request(), they use vmstate_register(), etc)
* they've been that way for a decade plus and nobody particularly has
stepped up to try to modernise the code (beyond some occasional
work here and there)
* we often don't have test cases for them, which means that if we
do try to do the necessary refactoring work on them we have no
idea if they even still work at all afterwards
All these machine types are also of hardware that has largely passed
away into history and where I would not be surprised to find that
e.g. the Linux kernel support was never tested on real hardware
any more.
After some consultation with the Linux kernel developers, we
are going to deprecate:
All PXA2xx machines:
akita Sharp SL-C1000 (Akita) PDA (PXA270)
borzoi Sharp SL-C3100 (Borzoi) PDA (PXA270)
connex Gumstix Connex (PXA255)
mainstone Mainstone II (PXA27x)
spitz Sharp SL-C3000 (Spitz) PDA (PXA270)
terrier Sharp SL-C3200 (Terrier) PDA (PXA270)
tosa Sharp SL-6000 (Tosa) PDA (PXA255)
verdex Gumstix Verdex Pro XL6P COMs (PXA270)
z2 Zipit Z2 (PXA27x)
All OMAP2 machines:
n800 Nokia N800 tablet aka. RX-34 (OMAP2420)
n810 Nokia N810 tablet aka. RX-44 (OMAP2420)
One of the OMAP1 machines:
cheetah Palm Tungsten|E aka. Cheetah PDA (OMAP310)
Rationale:
* for QEMU dropping individual machines is much less beneficial
than if we can drop support for an entire SoC
* the OMAP2 QEMU code in particular is large, old and unmaintained,
and none of the OMAP2 kernel maintainers said they were using
QEMU in any of their testing/development
* although there is a setup that is booting test kernels on some
of the PXA2xx machines, nobody seemed to be using them as part
of their active kernel development and my impression from the
email thread is that PXA is the closest of all these SoC families
to being dropped from the kernel soon
* nobody said they were using cheetah, so it's entirely
untested and quite probably broken
* on the other hand the OMAP1 sx1 model does seem to be being
used as part of kernel development, and there was interest
in keeping collie around
In particular, the mainstone, tosa and z2 machine types have
already been dropped from Linux.
Mark all these machine types as deprecated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240308171621.3749894-1-peter.maydell@linaro.org
To avoid a potential global variable shadow in
hw/i386/pc_piix.c::pc_init1(), rename Xen's
"ram_memory" as "xen_memory".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20231114143816.71079-11-philmd@linaro.org>
RISC-V should also generate the SPCR in a manner similar to ARM.
Therefore, instead of replicating the code, relocate this function
to the common AML build.
Signed-off-by: Sia Jee Heng <jeeheng.sia@starfivetech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240129021440.17640-2-jeeheng.sia@starfivetech.com>
[ Changes by AF:
- Add missing Language SPCR entry
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Now that we can generate reliable clock frequencies from the RCC, remove
the hacky definition of the sysclk in the b_l475e_iot01a initialisation
code and use the correct RCC clock.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240303140643.81957-8-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the necessary files to add a simple RCC implementation with just
reads from and writes to registers. Also instantiate the RCC in the
STM32L4x5_SoC. It is needed for accurate emulation of all the SoC
clocks and timers.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240303140643.81957-2-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
BCM2835 has three I2C controllers. All of them share the same interrupt line.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240224191038.2409945-3-rayhan.faizel@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add support for UART0, in preparation of AST2700 models
-----BEGIN PGP SIGNATURE-----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=gFeX
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20240227' of https://github.com/legoater/qemu into staging
aspeed queue:
* Add support for UART0, in preparation of AST2700 models
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmXd2nMACgkQUaNDx8/7
# 7KErPBAAjKRmJQF9aMEgf7uqsPnJojAVumFe63NE9Gqnvy4MzgoZWfdSnLl2Ddba
# im5IfR7MYv0tzJtqCVtz7o4JwXhhDwesWALQZBM/ms48aacPSNP+7Gn141yLuCCS
# Vr8NBSIz156lSsnFGnRUArcQTDKjDp/1TLRiGcS8SDm/S4Nn++nur+T054EZgbKR
# CMWDeavgzZRb9HPepvWDwqb9qs11hq5/onCqC886dVNznxEKAVYcd0FVbSn3OfDF
# 2EPvKh+fxHlW37wcctlGPnbJK5rRvFi78yZf5utSt+mlVhyiEXjQJ6p8zBIh2w5A
# NlsmUo/UYv1F41yC/vCFRR8KJ2wO5VW7zL6UCGMV6I9hxhu/Qw+FYqWdBbAZWsOO
# GFOkFbe8zbJFXTr/W7P5upBlA7U1/B9VbRj71eu01dqT+n8OGsk8yfnWVs1SjpoD
# 89ZIhpb7lSolQmjPPxrVyfUe3/8ncTx64+CZuAZjxPh/9HA8wDXwVRPtAbIvvGaZ
# YPQ4Qmd4m6nAANAvTg2ufj19WT64XKwrQ6O3IkmGcn0BzHl08GFjru8IUp6rbduG
# m6WqulL1Ej1PrYaiw5ktpJ4Fkoy6iEFXJOWfl3oTLp2KWE5VAohyRKI00AFnHiAC
# frK+cxT4bqDtJR8QbNyJy5d3ZGZV1R6ZA0XjQ1jtb8ty2qISysw=
# =gFeX
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 27 Feb 2024 12:49:55 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20240227' of https://github.com/legoater/qemu:
aspeed: fix hardcode boot address 0
aspeed: introduce a new UART0 device name
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds RPi4B device tree modifications:
- disable pcie, rng200, thermal sensor and genet devices
(they're going to be re-enabled in the following commits)
- create additional memory region in device tree
if RAM amount exceeds VC base address.
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240226000259.2752893-12-sergey.kambalin@auriga.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240226000259.2752893-11-sergey.kambalin@auriga.com
[PMM: Change name to 'raspi4b', not 'raspi4b-2g']
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pre-setup for raspberry pi 4 introduction
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240226000259.2752893-4-sergey.kambalin@auriga.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pre setup for BCM2838 introduction
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240226000259.2752893-2-sergey.kambalin@auriga.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This property allows users to change flash model on command line as
below.
ex: "-M xlnx-versal-virt,ospi-flash=mt35xu02gbba"
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Message-id: 20240220091721.82954-3-sai.pavan.boddu@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no point in checking do we have PCIe if first thing after check
is adding PCIe card without checking.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240215153311.186772-1-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the previous design of ASPEED SOCs QEMU model, it set the boot
address at "0" which was the hardcode setting for ast10x0, ast2600,
ast2500 and ast2400.
According to the design of ast2700, it has a bootmcu(riscv-32) which
is used for executing SPL and initialize DRAM and copy u-boot image
from SPI/Flash to DRAM at address 0x400000000 at SPL boot stage.
Then, CPUs(cortex-a35) execute u-boot, kernel and rofs.
Currently, qemu not support emulate two CPU architectures
at the same machine. Therefore, qemu will only support
to emulate CPU(cortex-a35) side for ast2700 and the boot
address is "0x4 00000000".
Fixed hardcode boot address "0" for future models using
a different mapping address.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The Aspeed datasheet refers to the UART controllers
as UART1 - UART13 for the ast10x0, ast2600, ast2500
and ast2400 SoCs and the Aspeed ast2700 introduces an UART0
and the UART controllers as UART0 - UART12.
To keep the naming in the QEMU models
in sync with the datasheet, let's introduce a new UART0 device name
and do the required adjustements.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - Kept original assert() in aspeed_soc_uart_set_chr()
- Fixed 'i' range in connect_serial_hds_to_uarts() loop ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Remove last two includes of hw/ide/intarnal.h outside of hw/ide and
replace them with newly added public header to allow moving internal.h
into hw/ide to really stop exposing it.
Fixes: a11f439a0e (hw/ide: Stop exposing internal.h to non-IDE files)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240223142633.933694E6004@zero.eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Use ahci_ide_create_devs() instead of open-coding it.
Not accessing AHCIDevice internals anymore allows to
remove "hw/ide/ahci_internal.h" (which isn't really a
public header).
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240226080632.9596-2-philmd@linaro.org>
Split the sysbus version to a separate file so that it is not
included in PCI-only machines, and adjust Kconfig for machines
that do need sysbus-ohci. The copyrights are based on the
time and employer of balrog and Paul Brook's contributions.
While adjusting the SM501 dependency, move it to the right place
instead of keeping it in the R4D machine.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240223124406.234509-10-pbonzini@redhat.com>
[PMD: Rename some functions using 'ohci_sysbus_' prefix]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Add the Exynos4210fimdState::'framebuffer-memory' property. Have
the board set it. We don't need to call sysbus_address_space()
anymore.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240226173805.289-5-philmd@linaro.org>
We want to set another qdev property (a link) for the FIMD
device, we can not use sysbus_create_varargs() which only
passes sysbus base address and IRQs as arguments. Inline
it so we can set the link property in the next commit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240216153517.49422-4-philmd@linaro.org>
Add the PL110::'framebuffer-memory' property. Have the different
ARM boards set it. We don't need to call sysbus_address_space()
anymore.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240226173805.289-3-philmd@linaro.org>
We want to set another qdev property (a link) for the pl110
and pl111 devices, we can not use sysbus_create_simple() which
only passes sysbus base address and IRQs as arguments. Inline
it so we can set the link property in the next commit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240226173805.289-2-philmd@linaro.org>
qdev.c is a mixture between IDE bus specific functions and IDE device
functions. Let's split it up to make it more obvious which part is
related to bus handling and which part is related to device handling.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20240220085505.30255-3-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Add the remaining devices (or unimplemented-device stubs) for
this board: SPI controllers, SCC, FPGAIO, I2S, RTC, the
QSPI write-config block, and ethernet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-13-peter.maydell@linaro.org
Add the GPIO, watchdog, dual-timer and I2C devices to the mps3-an536
board. These are all simple devices that just need to be created and
wired up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-12-peter.maydell@linaro.org
This board has a lot of UARTs: there is one UART per CPU in the
per-CPU peripheral part of the address map, whose interrupts are
connected as per-CPU interrupt lines. Then there are 4 UARTs in the
normal part of the peripheral space, whose interrupts are shared
peripheral interrupts.
Connect and wire them all up; this involves some OR gates where
multiple overflow interrupts are wired into one GIC input.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-11-peter.maydell@linaro.org
Create the CPUs, the GIC, and the per-CPU RAM block for
the mps3-an536 board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240206132931.38376-10-peter.maydell@linaro.org
The AN536 is another FPGA image for the MPS3 development board. Unlike
the existing FPGA images we already model, this board uses a Cortex-R
family CPU, and it does not use any equivalent to the M-profile
"Subsystem for Embedded" SoC-equivalent that we model in hw/arm/armsse.c.
It's therefore more convenient for us to model it as a completely
separate C file.
This commit adds the basic skeleton of the board model, and the
code to create all the RAM and ROM. We assume that we're probably
going to want to add more images in future, so use the same
base class/subclass setup that mps2-tz.c uses, even though at
the moment there's only a single subclass.
Following commits will add the CPUs and the peripherals.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-9-peter.maydell@linaro.org
QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().
Since we don't model the SoC, just use a QOM container.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240213155214.13619-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().
This commit plug the devices which aren't part of the SoC;
they will be plugged into a SoC container in the next one.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240213155214.13619-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240213155214.13619-3-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240213155214.13619-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An access fault is raised when the Access Flag is not set in the
looked-up PTE and the AFFD field is not set in the corresponding context
descriptor. This was already implemented for stage 2. Implement it for
stage 1 as well.
Signed-off-by: Luc Michel <luc.michel@amd.com>
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Mostafa Saleh <smostafa@google.com>
Message-id: 20240213082211.3330400-1-luc.michel@amd.com
[PMM: tweaked comment text]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The patchset adding the GMAC ethernet to this SoC crossed in the
mail with the patchset cleaning up the NIC handling. When we
create the GMAC modules we must call qemu_configure_nic_device()
so that the user has the opportunity to use the -nic commandline
option to create a network backend and connect it to the GMACs.
Add the missing call.
Fixes: 21e5326a7c ("hw/arm: Add GMAC devices to NPCM7XX SoC")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Message-id: 20240206171231.396392-2-peter.maydell@linaro.org
Armv8.1+ CPUs have the Virtual Host Extension (VHE) which adds a
non-secure EL2 virtual timer. We implemented the timer itself in the
CPU model, but never wired up its IRQ line to the GIC.
Wire up the IRQ line (this is always safe whether the CPU has the
interrupt or not, since it always creates the outbound IRQ line).
Report it to the guest via dtb and ACPI if the CPU has the feature.
The DTB binding is documented in the kernel's
Documentation/devicetree/bindings/timer/arm\,arch_timer.yaml
and the ACPI table entries are documented in the ACPI specification
version 6.3 or later.
Because the IRQ line ACPI binding is new in 6.3, we need to bump the
FADT table rev to show that we might be using 6.3 features.
Note that exposing this IRQ in the DTB will trigger a bug in EDK2
versions prior to edk2-stable202311, for users who use the virt board
with 'virtualization=on' to enable EL2 emulation and are booting an
EDK2 guest BIOS, if that EDK2 has assertions enabled. The effect is
that EDK2 will assert on bootup:
ASSERT [ArmTimerDxe] /home/kraxel/projects/qemu/roms/edk2/ArmVirtPkg/Library/ArmVirtTimerFdtClientLib/ArmVirtTimerFdtClientLib.c(72): PropSize == 36 || PropSize == 48
If you see that assertion you should do one of:
* update your EDK2 binaries to edk2-stable202311 or newer
* use the 'virt-8.2' versioned machine type
* not use 'virtualization=on'
(The versions shipped with QEMU itself have the fix.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Message-id: 20240122143537.233498-3-peter.maydell@linaro.org
Similarly to commits dadbb58f59..5ae79fe825 for other ARM boards,
connect FIQ output of the GIC CPU interfaces to the CPU.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240130152548.17855-1-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vhost-user-snd support
x2APIC mode with TCG support
CXL update to r3.1
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXMoXUPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpFtMIAKUKD0hzJrwOyPo4xsRUMbsB3ehIsJsMKfOK
w+JWzTaojAG8ENPelWBdL2sEIs5U73VOchjLqHbH2m5sz6GJ13214amvdU/fYc8+
/dU2ZKoAmaR5L1ovKO/fq07y/J6DrITZ5tosy2i84Xa8EnsL4j3wEPNVWsDi7dna
mvXUICSOOoJQ4O2YhSruKCQ8qIgF1/0Oi3u/rcrW3alSs8VQlrtQXxl6k+LbYqek
+Fytco3jMRHPvQ+GYUIwGuHjN15ghArcvbsV0GIa+24BPY5h7YbDYGbfasePT5OK
zDz51jitkoyDrQr+OzwOEe/X5+dVGhayRXfMtU5Qm53IE3y61qc=
=K4b1
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
vhost-user-snd support
x2APIC mode with TCG support
CXL update to r3.1
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXMoXUPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpFtMIAKUKD0hzJrwOyPo4xsRUMbsB3ehIsJsMKfOK
# w+JWzTaojAG8ENPelWBdL2sEIs5U73VOchjLqHbH2m5sz6GJ13214amvdU/fYc8+
# /dU2ZKoAmaR5L1ovKO/fq07y/J6DrITZ5tosy2i84Xa8EnsL4j3wEPNVWsDi7dna
# mvXUICSOOoJQ4O2YhSruKCQ8qIgF1/0Oi3u/rcrW3alSs8VQlrtQXxl6k+LbYqek
# +Fytco3jMRHPvQ+GYUIwGuHjN15ghArcvbsV0GIa+24BPY5h7YbDYGbfasePT5OK
# zDz51jitkoyDrQr+OzwOEe/X5+dVGhayRXfMtU5Qm53IE3y61qc=
# =K4b1
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 14 Feb 2024 11:18:13 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (60 commits)
MAINTAINERS: Switch to my Enfabrica email
virtio-gpu-rutabaga.c: override resource_destroy method
virtio-gpu.c: add resource_destroy class method
hw/display/virtio-gpu.c: use reset_bh class method
hw/smbios: Fix port connector option validation
hw/smbios: Fix OEM strings table option validation
virtio-gpu: Correct virgl_renderer_resource_get_info() error check
hw/cxl: Standardize all references on CXL r3.1 and minor updates
hw/cxl: Update mailbox status registers.
hw/cxl: Update RAS Capability Definitions for version 3.
hw/cxl: Update link register definitions.
hw/cxl: Update HDM Decoder capability to version 3
tests/acpi: Update DSDT.cxl to reflect change _STA return value.
hw/i386: Fix _STA return value for ACPI0017
tests/acpi: Allow update of DSDT.cxl
hw/mem/cxl_type3: Fix potential divide by zero reported by coverity
hw/cxl: Pass NULL for a NULL MemoryRegionOps
hw/cxl: Pass CXLComponentState to cache_mem_ops
hw/cxl/device: read from register values in mdev_reg_read()
hw/cxl/mbox: Remove dead code
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
s->smmu_pcibus_by_bus_num is a SMMUPciBus pointer cache indexed
by bus number, bus number may not always be a fixed value,
i.e., guest reboot to different kernel which set bus number with
different algorithm.
This could lead to smmu_iommu_mr() providing the wrong iommu MR.
Suggested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20240125073706.339369-3-zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Rather than just using qemu_configure_nic_device(), populate the MAC
address in the system-registers device by peeking at the NICInfo before
it's assigned to the device.
Generate the MAC address early, if there is no matching -nic option.
Otherwise the MAC address wouldn't be generated until net_client_init1()
runs.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Also update the test to specify which device to attach the test socket
to, and remove the comment lamenting the fact that we can't do so.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Some callers instantiate the device unconditionally, others will do so only
if there is a NICInfo to go with it. This appears to be fairly random, but
preseve the existing behaviour for now.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Some callers instantiate the device unconditionally, others will do so only
if there is a NICInfo to go with it. This appears to be fairly random, but
preserve the existing behaviour of each caller for now.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
This patch will allow the SPI controller to be accessible from BCM2835 based
boards as SPI0. SPI driver is usually disabled by default and config.txt does
not work.
Instead, dtmerge can be used to apply spi=on on a bcm2835 dtb file.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240129221807.2983148-3-rayhan.faizel@gmail.com
[PMM: indent tweak]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into trace events. Errors or warnings are converted to error_report and
warn_report calls.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: fe5e3bd54231abe933f95a24e0e88208cd8cfd8f.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into trace events. DPRINTFs that report guest errors are logged with
LOG_GUEST_ERROR.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 799c5141c5751cf2341e1d095349612e046424a8.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into trace events. DPRINTFs that report guest errors are logged with
LOG_GUEST_ERROR.#
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 39db71dd87bf2007cf7812f3d91dde53887f1f2f.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Leverage the common code introduced in commit c9cf636d48 ("machine:
Add a valid_cpu_types property") to check for the single valid CPU
type. Remove the now unused MachineClass::default_cpu_type field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Leverage the common code introduced in commit c9cf636d48 ("machine:
Add a valid_cpu_types property") to check for the single valid CPU
type. Remove the now unused MachineClass::default_cpu_type field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-9-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The npcm7xx Soc is created with a Cortex-A9 core, see in
hw/arm/npcm7xx.c:
static void npcm7xx_init(Object *obj)
{
NPCM7xxState *s = NPCM7XX(obj);
for (int i = 0; i < NPCM7XX_MAX_NUM_CPUS; i++) {
object_initialize_child(obj, "cpu[*]", &s->cpu[i],
ARM_CPU_TYPE_NAME("cortex-a9"));
}
The MachineClass::default_cpu_type field is ignored: delete it.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-8-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Musca boards use the embedded subsystems (SSE) tied to a specific
Cortex core. Our models only use the Cortex-M33.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Remove the now unused MachineClass::default_cpu_type field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-7-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The M2Sxxx SoC family can only be used with Cortex-M3.
Propagating the CPU type from the board level is pointless.
Hard-code the CPU type at the SoC level.
Remove the now ignored MachineClass::default_cpu_type field.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-6-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Restrict MachineClass::valid_cpu_types[] to the single
valid CPU types.
Instead of ignoring invalid CPU type requested by the user:
$ qemu-system-arm -M midway -cpu cortex-a7 -S -monitor stdio
QEMU 8.2.50 monitor - type 'help' for more information
(qemu) info qom-tree
/machine (midway-machine)
/cpu[0] (cortex-a15-arm-cpu)
...
we now display an error:
$ qemu-system-arm -M midway -cpu cortex-a7
qemu-system-arm: Invalid CPU model: cortex-a7
The only valid type is: cortex-a15
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Restrict MachineClass::valid_cpu_types[] to the single
valid CPU type.
Instead of ignoring invalid CPU type requested by the user:
$ qemu-system-arm -M nuri -cpu cortex-a7 -S -monitor stdio
QEMU 8.2.50 monitor - type 'help' for more information
(qemu) info qom-tree
/machine (nuri-machine)
/soc (exynos4210)
/cpu[0] (cortex-a9-arm-cpu)
...
We now display an error:
$ qemu-system-arm -M nuri -cpu cortex-a7
qemu-system-arm: Invalid CPU model: cortex-a7
The only valid type is: cortex-a9
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Update of buildroot images to 2023.11 (6.6.3 kernel)
* Check of the valid CPU type supported by aspeed machines
* Simplified models for the IBM's FSI bus and the Aspeed
controller bridge
-----BEGIN PGP SIGNATURE-----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=0C5S
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu into staging
aspeed queue:
* Update of buildroot images to 2023.11 (6.6.3 kernel)
* Check of the valid CPU type supported by aspeed machines
* Simplified models for the IBM's FSI bus and the Aspeed
controller bridge
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmW7Sa8ACgkQUaNDx8/7
# 7KG7mw/8DbMJY6aqgq5YANszzem1ktJphPCNxq081cbczCOUpCNX4aL+0/ANvxxD
# lbJQB+SZeIRmuFbxYPhq68rtzB4vG7tsQpns4H33EPKT4vuzF70lq4fgptMiun3q
# 1ZJ2LF3jonvQWdhbC17wzAQz0FFb4F7XOxz++UL4okPsgzsYItnd+TWs8q7+erRb
# 84UwN+eBTBAl/FiNk679/tBTqAfCVGgQ7dzotr4f3tg5POvrGOrlEjAn0O+dGGDj
# wgILmpEBsTsilRB1tz8Kw0j/v/VkHz1DJu45lRAV9CIrN22iKcjMilNGgNDT8kcI
# yAlxAw3iN+hVFqDov8wFPjDYd/Qw2oRAPy2Kd14hW9xL8zBOTms1JK5L0PS2+Feo
# ZjMJ2cOJq3t4Wt1ZXRhgHfF4ANwP0OZ/y9bHCy3CkBljEeiTQbikHP9gVV4qHXZH
# 4Q0HnDZQwAgobw3CmZ8jVx1dQueqy3ycuvkhCyv3S0l/tdbtXDtr5pNNu3dAP/PJ
# 3nifLdRImhDvxxO9GKaCdUVLzELzMJl0GrgAsVJPKVnKHA4IiVKmB+XcW9IUbfy/
# 3zA2wHJLrEF+MF6MsuNcEYCCqUvyNLm7rUrXk1wNLXpCJ35bbW5IYy7Ty/8E2GHb
# D5Cv/EPNhMBiNA4+HqQlMOTC13Ozv2qwCuWYCh2Ik8mnzaEiyTo=
# =0C5S
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 01 Feb 2024 07:35:11 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu:
hw/fsi: Update MAINTAINER list
hw/fsi: Added FSI documentation
hw/fsi: Added qtest
hw/arm: Hook up FSI module in AST2600
hw/fsi: Aspeed APB2OPB & On-chip peripheral bus
hw/fsi: Introduce IBM's FSI master
hw/fsi: Introduce IBM's cfam
hw/fsi: Introduce IBM's fsi-slave model
hw/fsi: Introduce IBM's FSI Bus
hw/fsi: Introduce IBM's scratchpad device
hw/fsi: Introduce IBM's Local bus
hw/arm/aspeed: Check for CPU types in machine_run_board_init()
hw/arm/aspeed: Introduce aspeed_soc_cpu_type() helper
hw/arm/aspeed: Init CPU defaults in a common helper
hw/arm/aspeed: Set default CPU count using aspeed_soc_num_cpus()
hw/arm/aspeed: Remove dead code
tests/avocado/machine_aspeed.py: Update buildroot images to 2023.11
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patchset introduces IBM's Flexible Service Interface(FSI).
Time for some fun with inter-processor buses. FSI allows a service
processor access to the internal buses of a host POWER processor to
perform configuration or debugging.
FSI has long existed in POWER processes and so comes with some baggage,
including how it has been integrated into the ASPEED SoC.
Working backwards from the POWER processor, the fundamental pieces of
interest for the implementation are:
1. The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on buses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.
2. The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.
3. The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.
4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The implementation appears as following in the qemu device tree:
(qemu) info qtree
bus: main-system-bus
type System
...
dev: aspeed.apb2opb, id ""
gpio-out "sysbus-irq" 1
mmio 000000001e79b000/0000000000001000
bus: opb.1
type opb
dev: fsi.master, id ""
bus: fsi.bus.1
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.1
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
bus: opb.0
type opb
dev: fsi.master, id ""
bus: fsi.bus.0
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.0
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
The LBUS is modelled to maintain the qdev bus hierarchy and to take
advantage of the object model to automatically generate the CFAM
configuration block. The configuration block presents engines in the
order they are attached to the CFAM's LBUS. Engine implementations
should subclass the LBusDevice and set the 'config' member of
LBusDeviceClass to match the engine's type.
CFAM designs offer a lot of flexibility, for instance it is possible for
a CFAM to be simultaneously driven from multiple FSI links. The modeling
is not so complete; it's assumed that each CFAM is attached to a single
FSI slave (as a consequence the CFAM subclasses the FSI slave).
As for FSI, its symbols and wire-protocol are not modelled at all. This
is not necessary to get FSI off the ground thanks to the mapping of the
CFAM address space onto the OPB address space - the models follow this
directly and map the CFAM memory region into the OPB's memory region.
Future work includes supporting more advanced accesses that drive the
FSI master directly rather than indirectly via the CFAM mapping, which
will require implementing the FSI state machine and methods for each of
the FSI symbols on the slave. Further down the track we can also look at
supporting the bitbanged SoftFSI drivers in Linux by extending the FSI
slave model to resolve sequences of GPIO IRQs into FSI symbols, and
calling the associated symbol method on the slave to map the access onto
the CFAM.
Testing:
Tested by reading cfam config address 0 on rainier machine type.
root@p10bmc:~# pdbg -a getcfam 0x0
p0: 0x0 = 0xc0022d15
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved FSIMasterState under AspeedAPB2OPBState
- modified fsi_opb_fsi_master_address() and
fsi_opb_opb2fsi_address()
- instroduced fsi_aspeed_apb2opb_init()
- reworked fsi_aspeed_apb2opb_realize()
- removed FSIMasterState object and fsi_opb_realize()
- simplified OPBus
- introduced fsi_aspeed_apb2opb_rw to fix endianness issue ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Aspeed SoCs use a single CPU type (set as AspeedSoCClass::cpu_type).
Convert it to a NULL-terminated array (of a single non-NULL element).
Set MachineClass::valid_cpu_types[] to use the common machine code
to provide hints when the requested CPU is invalid (see commit
e702cbc19e ("machine: Improve is_cpu_type_supported()").
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In order to alter AspeedSoCClass::cpu_type in the next
commit, introduce the aspeed_soc_cpu_type() helper to
retrieve the per-SoC CPU type from AspeedSoCClass.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rework aspeed_soc_num_cpus() as a new init_cpus_defaults()
helper to reduce code duplication.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Since commit b7f1a0cb76 ("arm/aspeed: Compute the number
of CPUs from the SoC definition") Aspeed machines use the
aspeed_soc_num_cpus() helper to set the number of CPUs.
Use it for the ast1030-evb (commit 356b230ed1 "aspeed/soc:
Add AST1030 support") and supermicrox11-bmc (commit 40a38df55e
"hw/arm/aspeed: Add board model for Supermicro X11 BMC") machines.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Remove copy/paste typo from commit 6c323aba40 ("hw/arm/aspeed:
Adding new machine Tiogapass in QEMU").
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add MMDC, OCOTP, SQPI, CAAM, and USBMISC as unimplemented devices.
This allows operating systems such as Linux to run emulations such as
mcimx6ul-evk.
Before commit 0cd4926b85 ("Refactor i.MX6UL processor code"), the affected
memory ranges were covered by the unimplemented DAP device. The commit
reduced the DAP address range from 0x100000 to 4kB, and the emulation
thus no longer covered the various unimplemented devices in the affected
address range.
Fixes: 0cd4926b85 ("Refactor i.MX6UL processor code")
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240120005356.2599547-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Various files in hw/arm/ don't require "cpu.h" anymore.
Except virt-acpi-build.c, all of them don't require any
ARM specific knowledge anymore and can be build once as
target agnostic units. Update meson accordingly.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-21-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move Arm A-class Generic Timer definitions to the new
"target/arm/gtimer.h" header so units in hw/ which don't
need access to ARMCPU internals can use them without
having to include the huge "cpu.h".
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-20-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM_CPU_IRQ/FIQ definitions are used to index the GPIO
IRQ created calling qdev_init_gpio_in() in ARMCPU instance_init()
handler. To allow non-ARM code to raise interrupt on ARM cores,
move they to 'target/arm/cpu-qom.h' which is non-ARM specific and
can be included by any hw/ file.
File list to include the new header generated using:
$ git grep -wEl 'ARM_CPU_(\w*IRQ|FIQ)'
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-18-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now than we can access the M-profile bank index
definitions from the target-agnostic "cpu-qom.h"
header, we don't need the huge "cpu.h" anymore
(except in hw/arm/armv7m.c). Reduce its inclusion
to the source unit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-17-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Declare arm_cpu_mp_affinity() prototype in the new
"target/arm/multiprocessing.h" header so units in
hw/arm/ can use it without having to include the huge
target-specific "cpu.h".
File list to include the new header generated using:
$ git grep -lw arm_cpu_mp_affinity
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-11-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Wrapper to return the mp affinity bits from the cpu.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename to arm_build_mp_affinity. This frees up the name for
other usage, and emphasizes that the cpu object is not involved.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-9-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/arm/smmuv3-internal.h uses the REG32() and FIELD()
macros defined in "hw/registerfields.h". Include it in
order to avoid when refactoring unrelated headers:
In file included from ../../hw/arm/smmuv3.c:34:
hw/arm/smmuv3-internal.h:36:28: error: expected identifier
REG32(IDR0, 0x0)
^
hw/arm/smmuv3-internal.h:37:5: error: expected function body after function declarator
FIELD(IDR0, S2P, 0 , 1)
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/arm/xilinx_zynq.c calls tswap32() which is declared
in "exec/tswap.h". Include it in order to avoid when
refactoring unrelated headers:
hw/arm/xilinx_zynq.c:103:31: error: call to undeclared function 'tswap32';
ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
board_setup_blob[n] = tswap32(board_setup_blob[n]);
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/arm/exynos4210.c calls tswap32() which is declared
in "exec/tswap.h". Include it in order to avoid when
refactoring unrelated headers:
hw/arm/exynos4210.c:499:22: error: call to undeclared function 'tswap32';
ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
smpboot[n] = tswap32(smpboot[n]);
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add watchdog timer support to Allwinner-H40 and Bananapi.
The watchdog timer is added as an overlay to the Timer
module memory map.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Message-id: 20240115182757.1095012-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports an AHCI compliant SATA controller.
Add support for it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240115182757.1095012-3-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports two USB host ports shared between a USB 2.0 EHCI
host controller and a USB 1.1 OHCI host controller. Add support for both
of them.
If machine USB support is not enabled, create unimplemented devices
for the USB memory ranges to avoid crashes when booting Linux.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240115182757.1095012-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TUSB6010 USB controller is soldered on the N800 and N810
tablets, thus is always present.
This is a migration compatibility break for the n800/n810
machines started with the '-usb none' option.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240119215106.45776-3-philmd@linaro.org
[PMM: fixed commit message typo]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The USB Controllers are part of the chipset, thus are
always present and mapped in memory.
This is a migration compatibility break for the cubieboard
machine started with the '-usb none' option.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240119215106.45776-2-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the musicpal key input device to use
qemu_add_kbd_event_handler(). This lets us simplify it because we no
longer need to track whether we're in the middle of a PS/2 multibyte
key sequence.
In the conversion we move the keyboard handler registration from init
to realize, because devices shouldn't disturb the state of the
simulation by doing things like registering input handlers until
they're realized, so that device objects can be introspected
safely.
The behaviour where key-repeat is permitted for the arrow-keys only
is intentional (added in commit 7c6ce4baed), so we retain it,
and add a comment to that effect.
This is a migration compatibility break for musicpal.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20231103182750.855577-1-peter.maydell@linaro.org
error_report() strings should not include trailing newlines; remove
the newline from the error we print when devices won't fit into the
address space of the CPU.
This commit also fixes the accidental hardcoded tabs that were in
this line, since we have to touch the line anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240118131649.2726375-1-peter.maydell@linaro.org
It's found that some of the CPU type names in the array of valid
CPU types are invalid because their corresponding classes aren't
registered, as reported by Peter Maydell.
[gshan@gshan build]$ ./qemu-system-arm -machine virt -cpu cortex-a9
qemu-system-arm: Invalid CPU model: cortex-a9
The valid models are: cortex-a7, cortex-a15, (null), (null), (null),
(null), (null), (null), (null), (null), (null), (null), (null), max
Fix it by consolidating the array of valid CPU types. After it's
applied, we have the following output when TCG is enabled.
[gshan@gshan build]$ ./qemu-system-arm -machine virt -cpu cortex-a9
qemu-system-arm: Invalid CPU model: cortex-a9
The valid models are: cortex-a7, cortex-a15, max
[gshan@gshan build]$ ./qemu-system-aarch64 -machine virt -cpu cortex-a9
qemu-system-aarch64: Invalid CPU model: cortex-a9
The valid models are: cortex-a7, cortex-a15, cortex-a35, cortex-a55,
cortex-a72, cortex-a76, cortex-a710, a64fx, neoverse-n1, neoverse-v1,
neoverse-n2, cortex-a53, cortex-a57, max
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2084
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20240111051054.83304-1-gshan@redhat.com
Fixes: fa8c617791 ("hw/arm/virt: Check CPU type in machine_run_board_init()")
Signed-off-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SYSCFG input GPIOs aren't connected yet. When the STM32L4x5 GPIO
device will be implemented, its output GPIOs will be connected to the
SYSCFG input GPIOs.
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240109194438.70934-3-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
RISC-V also needs to create the virtio in DSDT in the same way as ARM.
So, instead of duplicating the code, move this function to the device
specific file which is common across architectures.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20231218150247.466427-3-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V also needs to use the same code to create fw_cfg in DSDT. So,
avoid code duplication by moving the code in arm and riscv to a device
specific file.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20231218150247.466427-2-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240104141159.53883-1-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update the number of priority bits for a number of existing
SoCs according to their technical documentation:
- STM32F100/F205/F405/L4x5: 4 bits
- Stellaris (Sandstorm/Fury): 3 bits
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240106181503.1746200-4-sam@rfc1149.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A SoC will not have a direct access to the NVIC embedded in its ARM
core. By aliasing the "num-prio-bits" property similarly to what is
done for the "num-irq" one, a SoC can easily configure it on its
armv7m instance.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240106181503.1746200-3-sam@rfc1149.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds a new B-L475E-IOT01A board using the STM32L475VG SoC
as well as a dedicated documentation file.
The implementation is derived from the Netduino Plus 2 machine.
There are no peripherals implemented yet, only memory regions.
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240108135849.351719-3-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds a new STM32L4x5 SoC, it is necessary to add support for
the B-L475E-IOT01A board.
The implementation is derived from the STM32F405 SoC.
The implementation contains no peripherals, only memory regions are
implemented.
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240108135849.351719-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'start-powered-off' property has been added to ARM CPUs in
commit 5de164304a ("arm: Allow secondary KVM CPUs to be booted
via PSCI"), then eventually got generalized to all CPUs in commit
c1b701587e ("target/arm: Move start-powered-off property to generic
CPUState"). Since all CPUs have it, no need to check whether it is
available. Updating this property can't fail, so use &error_abort.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20231123143813.42632-5-philmd@linaro.org>
The 'mp-affinity' property is present since commit 15a21fe028
("target-arm: Add mp-affinity property for ARM CPU class").
Use it and remove a /* TODO */ comment. Since all ARM CPUs
have this property, use &error_abort, because this call can
not fail.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20231123143813.42632-4-philmd@linaro.org>
bcm2836_realize() is called by
- bcm2836_class_init() which sets:
bc->cpu_type = ARM_CPU_TYPE_NAME("cortex-a7")
- bcm2837_class_init() which sets:
bc->cpu_type = ARM_CPU_TYPE_NAME("cortex-a53")
Both Cortex-A7 / A53 have the ARM_FEATURE_CBAR set. If it isn't,
then this is a programming error: use &error_abort.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20231123143813.42632-3-philmd@linaro.org>
Set mc->valid_cpu_types so that the user specified CPU type can
be validated in machine_run_board_init(). We needn't to do it by
ourselves.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231204004726.483558-9-gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Set mc->valid_cpu_types so that the user specified CPU type can
be validated in machine_run_board_init(). We needn't to do it
by ourselves.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Leif Lindholm <quic_llindhol@quicinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231204004726.483558-8-gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Set mc->valid_cpu_types so that the user specified CPU type can be
validated in machine_run_board_init(). We needn't to do the check
by ourselves.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231204004726.483558-7-gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The 'host' CPU model isn't available until KVM or HVF is enabled.
For example, the following error messages are seen when the guest
is started with option '-cpu cortex-a8' on tcg after the next commit
is applied to check the CPU type in machine_run_board_init().
ERROR:../hw/core/machine.c:1423:is_cpu_type_supported: \
assertion failed: (model != NULL)
Bail out! ERROR:../hw/core/machine.c:1423:is_cpu_type_supported: \
assertion failed: (model != NULL)
Aborted (core dumped)
Hide 'host' CPU model until KVM or HVF is enabled. With this applied,
the valid CPU models can be shown.
qemu-system-aarch64: Invalid CPU type: cortex-a8
The valid types are: cortex-a7, cortex-a15, cortex-a35, \
cortex-a55, cortex-a72, cortex-a76, cortex-a710, a64fx, \
neoverse-n1, neoverse-v1, neoverse-n2, cortex-a53, \
cortex-a57, max
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231204004726.483558-6-gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231221031652.119827-19-richard.henderson@linaro.org>
* Some header clean-ups by Philippe
* Restrict type names to alphanumerical range (and a few special characters)
* Fix analyze-migration.py script on s390x
* Clean up and improve some tests
* Document handling of commas in CLI options parameters
-----BEGIN PGP SIGNATURE-----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=TA1/
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-12-20' of https://gitlab.com/thuth/qemu into staging
* Add compat machines for QEMU 9.0
* Some header clean-ups by Philippe
* Restrict type names to alphanumerical range (and a few special characters)
* Fix analyze-migration.py script on s390x
* Clean up and improve some tests
* Document handling of commas in CLI options parameters
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmWCtYsRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbWLnw//cNJrxG0V+j0iakX+C7HRumVrLBDI4KYY
# Cp2Hx92SyeQ0Kk8DJS6JueTV0SLjMsV77APu2YPH7ELmPlk+CB9gqmV7xVoYNvsm
# QbRPlIjFw8MHLekadc2A+C+pn48tWACoOdBEDIfazKrxybnf0B57RC/fIfMKHjbs
# 2ALCoFbbgphs7yWuzTHK8ayKaGMhUVkWfzHQwpnq899olHyZBhkl951uKJA6VmLx
# KvggePkpszLjmmXA8MH1hDCcizki31cB0ZKTbQFCyE42s2S3Hvg0GueU90O7Y1cj
# lS5tPVQxyEhUYMLL+/hudlf2OYqVn2BalB7ieUQIy6rG8yoc9zxfIKQi0ccl+2oA
# s8HRq5S0bSjtilQogU1LQL/Gk6W1/N9MmnhKvCGB+BTK5KX7s4EQk02y9gGZm/8s
# pMErMyaXTG4dLiTAK42VgMVDqCYvzBmE+Gj91OmoUR7fb+VMrsWxeBFxMPDn+VtL
# TMJegIFsjw2QCSitcU4v+nP0qtKgXGbuZtrGXKabrxH5PmeQFJDSM7TwpTK4qvjK
# QMIQKBbz8BfJnUzN8qAaaJEpp1T5tcMJClKtfcgxq/+VyaSaHLmD0cljqBC+g+y7
# FTo+fa7oYx44sAlqapdEXBSGn4T+J26iuCef13CCCiPfYBv/tk3b2E0AWHj4y58I
# +VpInjUaPBQ=
# =TA1/
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 20 Dec 2023 04:36:11 EST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-12-20' of https://gitlab.com/thuth/qemu:
tests/unit/test-qmp-event: Replace fixture by global variables
tests/unit/test-qmp-event: Simplify event emission check
tests/unit/test-qmp-event: Drop superfluous mutex
tests/qtest/npcm7xx_pwm-test: Only do full testing in slow mode
qemu-options: Clarify handling of commas in options parameters
tests/qtest/migration-test: Fix analyze-migration.py for s390x
qom/object: Limit type names to alphanumerical and some few special characters
tests/unit/test-io-task: Rename "qemu:dummy" to avoid colon in the name
memory: Remove "qemu:" prefix from the "qemu:ram-discard-manager" type name
hw: Replace anti-social QOM type names (again)
docs/system/arm: Fix for rename of type "xlnx.bbram-ctrl"
target: Restrict 'sysemu/reset.h' to system emulation
hw/s390x/ipl: Remove unused 'exec/exec-all.h' included header
hw/misc/mips_itu: Remove unnecessary 'exec/exec-all.h' header
hw/ppc/spapr_hcall: Remove unused 'exec/exec-all.h' included header
system/qtest: Restrict QTest API to system emulation
system/qtest: Include missing 'hw/core/cpu.h' header
MAINTAINERS: Add some more vmware-related files to the corresponding section
hw: Add compat machines for 9.0
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* arm/kvm: drop the split between "common KVM support" and
"64-bit KVM support", since 32-bit Arm KVM no longer exists
* arm/kvm: clean up APIs to be consistent about CPU arguments
* Don't implement *32_EL2 registers when EL1 is AArch64 only
* Restrict DC CVAP & DC CVADP instructions to TCG accel
* Restrict TCG specific helpers
* Propagate MDCR_EL2.HPMN into PMCR_EL0.N
* Include missing 'exec/exec-all.h' header
* fsl-imx: add simple RTC emulation for i.MX6 and i.MX7 boards
-----BEGIN PGP SIGNATURE-----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=GWIA
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20231219' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* arm/kvm: drop the split between "common KVM support" and
"64-bit KVM support", since 32-bit Arm KVM no longer exists
* arm/kvm: clean up APIs to be consistent about CPU arguments
* Don't implement *32_EL2 registers when EL1 is AArch64 only
* Restrict DC CVAP & DC CVADP instructions to TCG accel
* Restrict TCG specific helpers
* Propagate MDCR_EL2.HPMN into PMCR_EL0.N
* Include missing 'exec/exec-all.h' header
* fsl-imx: add simple RTC emulation for i.MX6 and i.MX7 boards
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmWB6o0ZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3mxMEACRpRxJ81pLs8fFYC5BgRhU
# BCxr+ZqarBygzsH9YWUN2TFFKlEZi7mLu6lzFsfN/qEmYCg8VslPbulQHqcGkx51
# kVxXFp/KuGlKt4zGRagZUJxgYAwwU5mnK6dTZT5/ZF6yWX67dXn8V7MP9lqqEPw5
# 5gut7Mu4f7MiAQbwZY1CWP+iu5uZmdsBuKxA6zkxOWJh/A1SfaqQRO6xVQttLAxS
# DPMTpQGmwPS4I+3gGNnqlSu6etp2tdy2K0cW3fhMp6hx70uNMHmFNzRhT/6TaKka
# 9AqXQsFHQiFXDGAm6PmCvfQI6KpLljDyNL/TuUkQWi72bGEHjUsJAdG0aXVOa30W
# uC7vuJkdZrP/t5P1AkZhWQUrlawDRV2YHNDD+gY4fxJL/STkGyU6M8R1nm1J+InN
# n0SeK0VHRC6DRPXCMQhC5QwKUH6ZjFZRs/r2opTu9p+ThQAQRmZBiVfdISCDMYnN
# DCiSb78gIFaUkwtiP44qq8MJQjsHnXtTD1Akqyo2fXSKs66jDK9Gnc8gENYdpghe
# 7V36bOp6scROHOB2a/r8gT42RKzSN6uh6xByaaToza63/bPgvHnn8vvQQbB01AgX
# zJC1xs3dwY8JMyqDefda0K0NDPS8TzNsXYmgxxxcQJpUvB4VVjet9VIMF3T+d8HO
# Pas41Z1gsQY+rcaRk/9mPA==
# =GWIA
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 19 Dec 2023 14:10:05 EST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20231219' of https://git.linaro.org/people/pmaydell/qemu-arm: (43 commits)
fsl-imx: add simple RTC emulation for i.MX6 and i.MX7 boards
target/arm/helper: Propagate MDCR_EL2.HPMN into PMCR_EL0.N
target/arm/tcg: Including missing 'exec/exec-all.h' header
target/arm: Restrict DC CVAP & DC CVADP instructions to TCG accel
target/arm: Restrict TCG specific helpers
target/arm: Don't implement *32_EL2 registers when EL1 is AArch64 only
target/arm/kvm: Have kvm_arm_hw_debug_active take a ARMCPU argument
target/arm/kvm: Have kvm_arm_handle_debug take a ARMCPU argument
target/arm/kvm: Have kvm_arm_handle_dabt_nisv take a ARMCPU argument
target/arm/kvm: Have kvm_arm_verify_ext_dabt_pending take a ARMCPU arg
target/arm/kvm: Have kvm_arm_[get|put]_virtual_time take ARMCPU argument
target/arm/kvm: Have kvm_arm_vcpu_finalize take a ARMCPU argument
target/arm/kvm: Have kvm_arm_vcpu_init take a ARMCPU argument
target/arm/kvm: Have kvm_arm_pmu_set_irq take a ARMCPU argument
target/arm/kvm: Have kvm_arm_pmu_init take a ARMCPU argument
target/arm/kvm: Have kvm_arm_pvtime_init take a ARMCPU argument
target/arm/kvm: Have kvm_arm_set_device_attr take a ARMCPU argument
target/arm/kvm: Have kvm_arm_sve_get_vls take a ARMCPU argument
target/arm/kvm: Have kvm_arm_sve_set_vls take a ARMCPU argument
target/arm/kvm: Have kvm_arm_add_vcpu_properties take a ARMCPU argument
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Unify the "kvm_arm.h" API: All functions related to ARM vCPUs
take a ARMCPU* argument. Use the CPU() QOM cast macro When
calling the generic vCPU API from "sysemu/kvm.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231123183518.64569-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Unify the "kvm_arm.h" API: All functions related to ARM vCPUs
take a ARMCPU* argument. Use the CPU() QOM cast macro When
calling the generic vCPU API from "sysemu/kvm.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231123183518.64569-9-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Unify the "kvm_arm.h" API: All functions related to ARM vCPUs
take a ARMCPU* argument. Use the CPU() QOM cast macro When
calling the generic vCPU API from "sysemu/kvm.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231123183518.64569-8-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both i.MX25 and i.MX6 SoC models ignore the Error argument when
setting the PHY number. Pick &error_abort which is the error
used by the i.MX7 SoC (see commit 1f7197deb0 "ability to change
the FEC PHY on i.MX7 processor").
Fixes: 74c1330582 ("ability to change the FEC PHY on i.MX25 processor")
Fixes: a9c167a3c4 ("ability to change the FEC PHY on i.MX6 processor")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231120115116.76858-1-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'stm32vldiscovery' machine ignores the CPU type requested by
the command line. This might confuse users, since the following
will create a machine with a Cortex-M3 CPU:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
qemu-system-aarch64: Invalid CPU type: neoverse-n1-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'netduino2' machine ignores the CPU type requested by the
command line. This might confuse users, since the following will
create a machine with a Cortex-M3 CPU:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
qemu-system-arm: Invalid CPU type: cortex-a9-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both 'netduinoplus2' and 'olimex-stm32-h405' machines ignore the
CPU type requested by the command line. This might confuse users,
since the following will create a machine with a Cortex-M4 CPU:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
qemu-system-aarch64: Invalid CPU type: cortex-r5f-arm-cpu
The valid types are: cortex-m4-arm-cpu
Since the SoC family can only use Cortex-M4 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since commit 9036e917f8 ("{include/}hw/arm: refactor virt PPI logic"),
GIC maintenance IRQ registration fails on arm64:
[ 0.979743] kvm [1]: Cannot register interrupt 9
That commit re-defined VIRTUAL_PMU_IRQ to be a INTID but missed a case
where the maintenance IRQ is actually referred by its PPI index. Just
like commit fa68ecb330 ("hw/arm/virt: fix PMU IRQ registration"), use
INITID_TO_PPI(). A search of "GIC_FDT_IRQ_TYPE_PPI" indicates that there
shouldn't be more similar issues.
Fixes: 9036e917f8 ("{include/}hw/arm: refactor virt PPI logic")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20231110090557.3219206-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of manually setting "foo-len" and "foo[i]" properties, build a
QList and use the new qdev_prop_set_array() helper to set the whole
array property with a single call.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20231109174240.72376-8-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of manually setting "foo-len" and "foo[i]" properties, build a
QList and use the new qdev_prop_set_array() helper to set the whole
array property with a single call.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20231109174240.72376-7-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of manually setting "foo-len" and "foo[i]" properties, build a
QList and use the new qdev_prop_set_array() helper to set the whole
array property with a single call.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20231109174240.72376-6-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of manually setting "foo-len" and "foo[i]" properties, build a
QList and use the new qdev_prop_set_array() helper to set the whole
array property with a single call.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20231109174240.72376-5-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of manually setting "foo-len" and "foo[i]" properties, build a
QList and use the new qdev_prop_set_array() helper to set the whole
array property with a single call.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20231109174240.72376-4-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of manually setting "foo-len" and "foo[i]" properties, build a
QList and use the new qdev_prop_set_array() helper to set the whole
array property with a single call.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20231109174240.72376-3-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
