pl011_create() is only used in DeviceRealize handlers,
not a hot-path. Inlining is not justified.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230220115114.25237-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current FIFO handling code does not reset RXFE/RXFF flags when guest
resets FIFO by writing to UARTLCR register, although internal FIFO state
is reset to 0 read count. Actual guest-visible flag update will happen
only on next data read or write attempt. As a result of that any guest
that expects RXFE flag to be set (and RXFF to be cleared) after resetting
FIFO will never see that happen.
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230123162304.26254-5-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PL011 currently lacks a reset method. Implement it.
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230123162304.26254-4-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Previous change slightly modified the way we handle data writes when
FIFO is disabled. Previously we kept incrementing read_pos and were
storing data at that position, although we only have a
single-register-deep FIFO now. Then we changed it to always store data
at pos 0.
If guest disables FIFO and the proceeds to read data, it will work out
fine, because we still read from current read_pos before setting it to
0.
However, to make code less fragile, introduce a post_load hook for
PL011State and move fixup read FIFO state when FIFO is disabled. Since
we are introducing a post_load hook, also do some sanity checking on
untrusted incoming input state.
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Message-id: 20230123162304.26254-3-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PL011 can be in either of 2 modes depending guest config: FIFO and
single register. The last mode could be viewed as a 1-element-deep FIFO.
Current code open-codes a bunch of depth-dependent logic. Refactor FIFO
depth handling code to isolate calculating current FIFO depth.
One functional (albeit guest-invisible) side-effect of this change is
that previously we would always increment s->read_pos in UARTDR read
handler even if FIFO was disabled, now we are limiting read_pos to not
exceed FIFO depth (read_pos itself is reset to 0 if user disables FIFO).
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230123162304.26254-2-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PL011 TRM says that "UARTIBRD = 0 is invalid and UARTFBRD is ignored
when this is the case". But the code looks at FBRD for the invalid case.
Fix this.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Message-id: 1408f62a2e45665816527d4845ffde650957d5ab.1665051588.git.baruchs-c@neureality.ai
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Break events are currently only handled by chardev/char-serial.c, so we
just ignore errors, which results in no behaviour change for other
chardevs.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Message-id: 20210806144700.3751979-1-jlu@pengutronix.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A clock is added by commit aac63e0e6e ("hw/char/pl011: add a clock
input") since v5.2.0 which corresponds to virt-5.2 machine type. It
causes backwards migration failure from upstream to downstream (v5.1.0)
when the machine type is specified with virt-5.1.
This fixes the issue by following instructions from section "Connecting
subsections to properties" in docs/devel/migration.rst. With this applied,
the PL011 clock is migrated based on the machine type.
virt-5.2 or newer: migration
virt-5.1 or older: non-migration
Cc: qemu-stable@nongnu.org # v5.2.0+
Fixes: aac63e0e6e ("hw/char/pl011: add a clock input")
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20210318023801.18287-1-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Clock framework allows users to specify a callback which is
called after the clock's period has been updated. Some users need to
also have a callback which is called before the clock period is
updated.
As the first step in adding support for notifying Clock users on
pre-update events, add an argument to the ClockCallback to specify
what event is being notified, and add an argument to the various
functions for registering a callback to specify which events are
of interest to that callback.
Note that the documentation update renders correct the previously
incorrect claim in 'Adding a new clock' that callbacks "will be
explained in a following section".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-2-peter.maydell@linaro.org
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add a clock input to the PL011 UART so we can compute the current baud
rate and trace it. This is intended for developers who wish to use QEMU
to e.g. debug their firmware or to figure out the baud rate configured
by an unknown/closed source binary.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Chardev events are listed in the QEMUChrEvent enum.
By using the enum in the IOEventHandler typedef we:
- make the IOEventHandler type more explicit (this handler
process out-of-band information, while the IOReadHandler
is in-band),
- help static code analyzers.
This patch was produced with the following spatch script:
@match@
expression backend, opaque, context, set_open;
identifier fd_can_read, fd_read, fd_event, be_change;
@@
qemu_chr_fe_set_handlers(backend, fd_can_read, fd_read, fd_event,
be_change, opaque, context, set_open);
@depends on match@
identifier opaque, event;
identifier match.fd_event;
@@
static
-void fd_event(void *opaque, int event)
+void fd_event(void *opaque, QEMUChrEvent event)
{
...
}
Then the typedef was modified manually in
include/chardev/char-fe.h.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-15-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
The pl011 logs when the guest makes a bad access. It prints
the address offset in hex but confusingly omits the '0x'
prefix; add it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL011 UART has six interrupt lines:
* RX (receive data)
* TX (transmit data)
* RT (receive timeout)
* MS (modem status)
* E (errors)
* combined (logical OR of all the above)
So far we have only emulated the combined interrupt line;
add support for the others, so that boards that wire them
up to different interrupt controller inputs can do so.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl011's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Frontends should have an interface to setup the handler of a backend change.
The interface will be used in the next commits
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1499342940-56739-3-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move all the frontend struct and methods to a seperate unit. This avoids
accidentally mixing backend and frontend calls, and helps with readabilty.
Make qemu_chr_replay() a macro shared by both char and char-fe.
Export qemu_chr_write(), and use a macro for qemu_chr_write_all()
(nb: yes, CharBackend is for char frontend :)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
So they are all in one place. The following patch will move serial &
parallel declarations to the respective headers.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
No need to keep explicit_fe_open around if it affects only a
qemu_chr_fe_set_handlers(). Use an additional argument instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases, front ends do not care about the side effect of
CharBackend, so we can simply skip the checks and call the qemu_chr_fe
functions even without associated CharDriver.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-20-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_chr_accept_input() and qemu_chr_disconnect() are only used by
frontend, so use qemu_chr_fe prefix.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-14-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Store the property in a CharBackend instead of CharDriverState*. This
also replace systematically chr by chr.chr to access the
CharDriverState*. The following patches will replace it with calls to
qemu_chr_fe CharBackend functions.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The qemu_chr_fe_write method will return -1 on EAGAIN if the
chardev backend write would block. Almost no callers of the
qemu_chr_fe_write() method check the return value, instead
blindly assuming data was successfully sent. In most cases
this will lead to silent data loss on interactive consoles,
but in some cases (eg RNG EGD) it'll just cause corruption
of the protocol being spoken.
We unfortunately can't fix the virtio-console code, due to
a bug in the Linux guest drivers, which would cause the
entire Linux kernel to hang if we delay processing of the
incoming data in any way. Fixing this requires first fixing
the guest driver to not hold spinlocks while writing to the
hvc device backend.
Fixes bug: https://bugs.launchpad.net/qemu/+bug/1586756
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1473170165-540-4-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* drop qemu_char_get_next_serial and use chardev prop
* add pl011_create wrapper function to create pl011 uart device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-2-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Device models aren't supposed to go on fishing expeditions for
backends. They should expose suitable properties for the user to set.
For onboard devices, board code sets them.
A number of sysbus devices pick up block backends in their init() /
instance_init() methods with drive_get_next() instead: sl-nand,
milkymist-memcard, pl181, generic-sdhci.
Likewise, a number of sysbus devices pick up character backends in
their init() / realize() methods with qemu_char_get_next_serial():
cadence_uart, digic-uart, etraxfs,serial, lm32-juart, lm32-uart,
milkymist-uart, pl011, stm32f2xx-usart, xlnx.xps-uartlite.
All these mistakes are already marked FIXME. See the commit that
added these FIXMEs for a more detailed explanation of what's wrong.
Fortunately, only machines ppce500 and pseries-* support -device with
sysbus devices, and none of the devices above is supported with these
machines.
Set cannot_instantiate_with_device_add_yet to preserve our luck.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Character devices defined with -serial and -parallel are for board
initialization to wire up. Board code examines serial_hds[] and
parallel_hds[] to find them, and creates devices with their qdev
chardev properties set accordingly.
Except a few devices go on a fishing expedition for a suitable backend
instead of exposing a chardev property for board code to set: they use
serial_hds[] (often via qemu_char_get_next_serial()) or parallel_hds[]
in their realize() or init() method to connect to a backend.
Picking up backends that way works when the devices are created by
board code. But it's inappropriate for -device or device_add. Not
only is it inconsistent with how the other characrer device models
work (they connect to a backend explicitly identified by a "chardev"
property), it breaks when the backend has been picked up by the board
or a previous -device / device_add already.
Example:
$ qemu-system-ppc64 -M bamboo -S -device i82378 -device pc87312 -device pc87312
qemu-system-ppc64: -device pc87312: Property 'isa-parallel.chardev' can't take value 'parallel0', it's in use
Mark them with suitable FIXME comments.
Cc: Li Guang <lig.fnst@cn.fujitsu.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: "Andreas Färber" <andreas.faerber@web.de>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The receive fifo full bit should be set when 1 character is received and
the fifo is disabled or when 16 characters are in the fifo.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1395166721-15716-4-git-send-email-robherring2@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Offset 4 is UARTRSR/UARTECR, not the UARTCR. The UARTCR would be
corrupted if the UARTRSR is ever written. Fix by implementing a correct
model of the UARTRSR/UARTECR register. Reads of this register simply
reflect the error bits in data register. Only breaks can be triggered in
QEMU. With the pl011_can_receive function, we effectively have flow
control between the host and the model. Framing and parity errors simply
don't make sense in the model and will never occur.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1395166721-15716-3-git-send-email-robherring2@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Intermittent issues have been seen where no serial input occurs. It
appears the pl011 gets in a state where the rx interrupt never fires
because the rx interrupt only asserts when crossing the fifo trigger
level. The fifo state appears to get out of sync when the pl011 is
re-configured. This combined with the rx timeout interrupt not being
modeled results in no more rx interrupts.
Disabling the fifo is the recommended way to clear the tx fifo in the
TRM (section 3.3.8). The behavior in this case for the rx fifo is
undefined in the TRM, but having fifo contents to be maintained during
configuration changes is not likely expected behavior. Reseting the
fifo state when the fifo size is changed is the simplest solution.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1395166721-15716-2-git-send-email-robherring2@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let the Luminary variant inherit from the ARM one, overwriting its ID on
instance_init. Introduce type constant and use QOM casts. Replace
triplicated SysBusDevice initfn with QOM realizefn and instance_init.
Signed-off-by: Andreas Färber <afaerber@suse.de>
