atoui() and get_index() pass char values to isdigit(). With a
standard isdigit(), we'd get undefined behavior when the value is
negative. Can't happen as char is unsigned on s390x. Even if it
ould, we're actually using isdigit() from pc-bios/s390-ccw/libc.h
here, which works fine for negative values. Clean up anyway, just
to avoid setting a bad example.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190418145355.21100-6-armbru@redhat.com>
[thuth: updated the commit message]
Signed-off-by: Thomas Huth <thuth@redhat.com>
zIPL boot menu entries can be non-sequential. Let's account
for this issue for the s390 enumerated boot menu. Since we
can no longer print a range of available entries to the
user, we have to present a list of each available entry.
An example of this menu:
s390-ccw Enumerated Boot Menu.
[0] default
[1]
[2]
[7]
[8]
[9]
[11]
[12]
Please choose:
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
zIPL boot menu entries can be non-sequential. Let's account
for this issue for the s390 zIPL boot menu. Since this boot
menu is actually an imitation and is not completely capable
of everything the real zIPL menu can do, let's also print a
different banner to the user.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Interactive boot menu for scsi. This follows a similar procedure
as the interactive menu for eckd dasd. An example follows:
s390x Enumerated Boot Menu.
3 entries detected. Select from index 0 to 2.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Added additional "break;" statement to avoid analyzer warnings]
Signed-off-by: Thomas Huth <thuth@redhat.com>
If no boot menu options are present, then flag the boot menu to
use the zipl options that were set in the zipl configuration file
(and stored on disk by zipl). These options are found at some
offset prior to the start of the zipl boot menu banner. The zipl
timeout value is limited to a 16-bit unsigned integer and stored
as seconds, so we take care to convert it to milliseconds in order
to conform to the rest of the boot menu functionality. This is
limited to CCW devices.
For reference, the zipl configuration file uses the following
fields in the menu section:
prompt=1 enable the boot menu
timeout=X set the timeout to X seconds
To explicitly disregard any boot menu options, then menu=off or
<bootmenu enable='no' ... /> must be specified.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It is possible while waiting for multiple types of external
interrupts that we might have pending irqs remaining between
irq consumption and irq-type disabling. Those interrupts
could potentially propagate to the guest after IPL completes
and cause unwanted behavior.
As it is today, the SCLP will only recognize write events that
are enabled by the control program's send and receive masks. To
limit the window for, and prevent further irqs from, ASCII
console events (specifically keystrokes), we should only enable
the control program's receive mask when we need it.
While we're at it, remove assignment of the (non control program)
send and receive masks, as those are actually set by the SCLP.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Implements an sclp_read function to capture input from the
console and a wrapper function that handles parsing certain
characters and adding input to a buffer. The input is checked
for any erroneous values and is handled appropriately.
A prompt will persist until input is entered or the timeout
expires (if one was set). Example:
Please choose (default will boot in 10 seconds):
Correct input will boot the respective boot index. If the
user's input is empty, 0, or if the timeout expires, then
the default zipl entry will be chosen. If the input is
within the range of available boot entries, then the
selection will be booted. Any erroneous input will cancel
the timeout and re-prompt the user.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When the boot menu options are present and the guest's
disk has been configured by the zipl tool, then the user
will be presented with an interactive boot menu with
labeled entries. An example of what the menu might look
like:
zIPL v1.37.1-build-20170714 interactive boot menu.
0. default (linux-4.13.0)
1. linux-4.13.0
2. performance
3. kvm
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Read the stage2 boot loader data block-by-block. We scan the
current block for the string "zIPL" to detect the start of the
boot menu banner. We then load the adjacent blocks (previous
block and next block) to account for the possibility of menu
data spanning multiple blocks.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reads boot menu flag and timeout values from the iplb and
sets the respective fields for the menu.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
