After a flash device enters CFI mode from autoselect mode, the reset
command returns the device to autoselect mode. An additional reset
command is necessary to return to read array mode.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-7-stephen.checkoway@oberlin.edu>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Split the if() condition check and arrange the indentation to
ease the review of the next patches. No logical change.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-21-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Extract the pflash_regions_count() function, the code will be
easier to review.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-20-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Some flash chips support sectors of different sizes. For example, the
AMD AM29LV160DT has 31 64 kB sectors, one 32 kB sector, two 8 kB
sectors, and a 16 kB sector, in that order. The AM29LV160DB has those in
the reverse order.
The `num-blocks` and `sector-length` properties work exactly as they did
before: a flash device with uniform sector lengths. To get non-uniform
sector lengths for up to four regions, the following properties may be
set
- region 0. `num-blocks0` and `sector-length0`;
- region 1. `num-blocks1` and `sector-length1`;
- region 2. `num-blocks2` and `sector-length2`; and
- region 3. `num-blocks3` and `sector-length3`.
If the uniform and nonuniform properties are set, then both must specify
a flash device with the same total size. It would be better to disallow
both being set, or make `num-blocks0` and `sector-length0` alias
`num-blocks` and `sector-length`, but that would make testing currently
impossible.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased, add assert() on pri_offset]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The 'page mode' feature entry was implicitly set as zero
(not supported). Document it exists, so we won't discard
it if we squeeze the CFI table.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Manufacturers are allowed to move the PRI table, this is why the
offset is queryable via fixed offsets 0x15/0x16.
Add a variable to hold the offset, so it will be easier to later
move the PRI table.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-17-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
We can directly use pfl->total_len, remove the local 'chip_len'
variable.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Most AMD commands only examine 11 bits of the address. This masks the
addresses used in the comparison to 11 bits. The exceptions are word or
sector addresses which use offset directly rather than the shifted
offset, boff.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-4-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The pflash_read()/pflash_write() can check the device endianess
via the pfl->be variable, so remove the 'int be' argument.
Since the big/little MemoryRegionOps are now identical, it is
pointless to declare them both. Unify them.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch to ease review]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Extract the code block in a new function, remove a goto statement.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch, remove the XXX tracing comment]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The load/store API eases code review.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch, simplified tracing]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The load/store API eases code review.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Pull out all of the code to modify the status into simple helper
functions. Status handling becomes more complex once multiple
chips are interleaved to produce a single device.
No change in functionality is intended with this commit.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
No change in functionality is intended with this commit.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Always compile the debug code to prevent format string to bitrot.
Delete dead code.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch, use PRIx32]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Use a field width format to have a single function to log
the different width accesses.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-4-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Call the read() trace function after the value is set, so we can
log the returned value.
Rename the I/O trace functions with '_io_' in their name.
Reviewed-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-3-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
* Fix build
* xen-block: support feature-large-sector-size
* xen-block: Support IOThread polling for PV shared rings
* Avoid usage of a VLA
* Cleanup Xen headers usage
-----BEGIN PGP SIGNATURE-----
iQFOBAABCgA4FiEE+AwAYwjiLP2KkueYDPVXL9f7Va8FAl0Q7JgaHGFudGhvbnku
cGVyYXJkQGNpdHJpeC5jb20ACgkQDPVXL9f7Va8B1wf/bL9gdT/1R9474ZfbWAGZ
KzkCo0C3jXUWRXd9z/UVwkmOhz0tLj1otx0fR+HFM4An+YAY6D0oZAKO9SCHhGDQ
XflAK74dw1ieuZI+3Q5PXQO5xM1Oz0J+3TGlOFdZlh5UD68mEzteGnzU/zzs7i4E
AZiKVOdO4YzMdHLVO4X/AqZH48n82FxjKcog7cZ9fTqDUz8SZGwJVSWocUZ0yOWb
uhAacvhwHeZj64NuNShyF/RM7jolTk4CZWJv8Gy9CPxOM7noQIv0ttwu+QWCmODg
pdTxd8HrE4rTnKaQFiHVas/AZ3cOfRw9RjdsARhXtGJq8AaQag9Q0iLZpyBYBfsF
6w==
=MDEA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/aperard/tags/pull-xen-20190624' into staging
Xen queue
* Fix build
* xen-block: support feature-large-sector-size
* xen-block: Support IOThread polling for PV shared rings
* Avoid usage of a VLA
* Cleanup Xen headers usage
# gpg: Signature made Mon 24 Jun 2019 16:30:32 BST
# gpg: using RSA key F80C006308E22CFD8A92E7980CF5572FD7FB55AF
# gpg: issuer "anthony.perard@citrix.com"
# gpg: Good signature from "Anthony PERARD <anthony.perard@gmail.com>" [marginal]
# gpg: aka "Anthony PERARD <anthony.perard@citrix.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5379 2F71 024C 600F 778A 7161 D8D5 7199 DF83 42C8
# Subkey fingerprint: F80C 0063 08E2 2CFD 8A92 E798 0CF5 572F D7FB 55AF
* remotes/aperard/tags/pull-xen-20190624:
xen: Import other xen/io/*.h
Revert xen/io/ring.h of "Clean up a few header guard symbols"
xen: Drop includes of xen/hvm/params.h
xen: Avoid VLA
xen-bus / xen-block: add support for event channel polling
xen-bus: allow AioContext to be specified for each event channel
xen-bus: use a separate fd for each event channel
xen-block: support feature-large-sector-size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The device mistakenly reports that the Weighted Round Robin with Urgent
Priority Class arbitration mechanism is supported.
It is not.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Message-id: 20190606092530.14206-1-klaus@birkelund.eu
Acked-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
A Xen public header have been imported into QEMU (by
f65eadb639 "xen: import ring.h from xen"), but there are other header
that depends on ring.h which come from the system when building QEMU.
This patch resolves the issue of having headers from the system
importing a different copie of ring.h.
This patch is prompt by the build issue described in the previous
patch: 'Revert xen/io/ring.h of "Clean up a few header guard symbols"'
ring.h and the new imported headers are moved to
"include/hw/xen/interface" as those describe interfaces with a guest.
The imported headers are cleaned up a bit while importing them: some
part of the file that QEMU doesn't use are removed (description
of how to make hypercall in grant_table.h have been removed).
Other cleanup:
- xen-mapcache.c and xen-legacy-backend.c don't need grant_table.h.
- xenfb.c doesn't need event_channel.h.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190621105441.3025-3-anthony.perard@citrix.com>
This patch introduces a poll callback for event channel fd-s and uses
this to invoke the channel callback function.
To properly support polling, it is necessary for the event channel callback
function to return a boolean saying whether it has done any useful work or
not. Thus xen_block_dataplane_event() is modified to directly invoke
xen_block_handle_requests() and the latter only returns true if it actually
processes any requests. This also means that the call to qemu_bh_schedule()
is moved into xen_block_complete_aio(), which is more intuitive since the
only reason for doing a deferred poll of the shared ring should be because
there were previously insufficient resources to fully complete a previous
poll.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190408151617.13025-4-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds an AioContext parameter to xen_device_bind_event_channel()
and then uses aio_set_fd_handler() to set the callback rather than
qemu_set_fd_handler().
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190408151617.13025-3-paul.durrant@citrix.com>
[Call aio_set_fd_handler() with is_external=true]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
A recent Xen commit [1] clarified the semantics of sector based quantities
used in the blkif protocol such that it is now safe to create a xen-block
device with a logical_block_size != 512, as long as the device only
connects to a frontend advertizing 'feature-large-block-size'.
This patch modifies xen-block accordingly. It also uses a stack variable
for the BlockBackend in xen_block_realize() to avoid repeated dereferencing
of the BlockConf pointer, and changes the parameters of
xen_block_dataplane_create() so that the BlockBackend pointer and sector
size are passed expicitly rather than implicitly via the BlockConf.
These modifications have been tested against a recent Windows PV XENVBD
driver [2] using a xen-disk device with a 4kB logical block size.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=commit;h=67e1c050e36b2c9900cca83618e56189effbad98
[2] https://winpvdrvbuild.xenproject.org:8080/job/XENVBD-master/126
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190409164038.25484-1-paul.durrant@citrix.com>
[Edited error message]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The uninitialized memory allocated for the command FIFO of the
floppy controller during the VM hardware initialization incurs
many unwanted reports by Valgrind when VM state is being saved.
That verbosity hardens a search for the real memory issues when
the iotests run. Particularly, the patch eliminates 20 unnecessary
reports of the Valgrind tool in the iotest #169.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-id: 1559154027-282547-1-git-send-email-andrey.shinkevich@virtuozzo.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
This adds a new parameter to blk_new() which requires its callers to
declare from which AioContext this BlockBackend is going to be used (or
the locks of which AioContext need to be taken anyway).
The given context is only stored and kept up to date when changing
AioContexts. Actually applying the stored AioContext to the root node
is saved for another commit.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add an Error parameter to blk_set_aio_context() and use
bdrv_child_try_set_aio_context() internally to check whether all
involved nodes can actually support the AioContext switch.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kenneth Heitke <kenneth.heitke@intel.com>
Reviewed-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since we now support the message VHOST_USER_GET_INFLIGHT_FD
and VHOST_USER_SET_INFLIGHT_FD. The backend is able to restart
safely because it can track inflight I/O in shared memory.
This patch allows qemu to reconnect the backend after
connection closed.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Ni Xun <nixun@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190320112646.3712-7-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a return value for vhost_user_blk_start() to check whether
we start vhost-user backend successfully or not.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190320112646.3712-6-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We should only start vhost-user backend at the first kick for
virtio 1.0 transitional devices.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190320112646.3712-5-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use started flag in vhost_user_blk_set_status() to decide if
starting vhost-user backend or not.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190320112646.3712-4-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
`nvme_dma_read_prp` erronously used `qemu_iovec_*to*_buf` instead of
`qemu_iovec_*from*_buf` when the request involved the controller memory
buffer.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Reviewed-by: Kenneth Heitke <kenneth.heitke@intel.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Factored out of pc_system_firmware_init() so the next commit can reuse
it in hw/arm/virt.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190416091348.26075-3-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Xen blkif protocol requires that sector based quantities should be
interpreted strictly as multiples of 512 bytes. Specifically:
"first_sect and last_sect in blkif_request_segment, as well as
sector_number in blkif_request, are always expressed in 512-byte units."
Commit fcab2b464e "xen: add header and build dataplane/xen-block.c"
incorrectly modified behaviour to use the block device logical_block_size
property as the scale, instead of correctly shifting values by the
hardcoded BDRV_SECTOR_BITS (and hence scaling them to 512 byte units).
This patch undoes that change and restores compliance with the spec.
Furthermore, this patch also restores the original xen_disk behaviour
of advertizing a hardcoded 'sector-size' value of 512 in xenstore and
scaling 'sectors' accordingly. The realize() method is also modified to
fail if logical_block_size is set to anything other than 512.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190401121719.27208-1-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and properly enable it when synthesizing a drive.
The Xen toolstack sets 'discard-enable' to '1' in xenstore when it wants
to enable discard on a specified image. The code in
xen_block_drive_create() correctly parses this and uses it to set
'discard' to 'unmap' for the file_layer, but fails to do the same for the
driver_layer (which effectively disables it). Meanwhile the code in
xen_block_realize() advertizes discard support to the frontend in the
default case (because conf->discard_granularity defaults to -1), even when
the underlying image may not handle it.
This patch adds the missing option to the driver_layer in
xen_block_driver_create() and checks whether BDRV_O_UNMAP is actually
set on the block device before advertizing discard to the frontend.
In the case that discard is supported it also makes sure that the
granularity is set to the physical block size.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190320142825.24565-1-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
We disabled code to limit device sizes to 8, 16, 32 or 64MiB more than
a decade ago in commit 95d1f3edd5 and c8b153d794, v0.9.1. Bury.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
[Extracted from a larger patch, extended to pflash_cfi02.c]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190319163551.32499-3-armbru@redhat.com>
We reject undersized backends with a rather enigmatic "failed to read
the initial flash content" error. For instance:
$ qemu-system-ppc64 -S -display none -M sam460ex -drive if=pflash,format=raw,file=eins.img
qemu-system-ppc64: Initialization of device cfi.pflash02 failed: failed to read the initial flash content
We happily accept oversized images, ignoring their tail. Throwing
away parts of firmware that way is pretty much certain to end in an
even more enigmatic failure to boot.
Require the backend's size to match the device's size exactly. Report
mismatch like this:
qemu-system-ppc64: Initialization of device cfi.pflash01 failed: device requires 1048576 bytes, block backend provides 512 bytes
Improve the error for actual read failures to "can't read block
backend".
To avoid duplicating even more code between the two pflash device
models, do all that in new helper blk_check_size_and_read_all().
The error reporting can still be confusing. For instance:
qemu-system-ppc64 -S -display none -M taihu -drive if=pflash,format=raw,file=eins.img -drive if=pflash,unit=1,format=raw,file=zwei.img
qemu-system-ppc64: Initialization of device cfi.pflash02 failed: device requires 2097152 bytes, block backend provides 512 bytes
Leaves the user guessing which of the two -drive is wrong. Mention
the issue in a TODO comment.
Suggested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190319163551.32499-2-armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Patch created mechanically by rerunning:
$ spatch --sp-file scripts/coccinelle/qobject.cocci \
--macro-file scripts/cocci-macro-file.h \
--dir hw/block --in-place
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190313174433.12966-1-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch adds support for vhost-user-blk device to get/set
inflight buffer from/to backend.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190228085355.9614-6-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Take a VhostUserState* that can be pre-allocated, and initialize it
with the associated chardev.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Tiwei Bie <tiwei.bie@intel.com>
Message-Id: <20190308140454.32437-4-marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The implementation used blocks units rather than the expected bytes.
Fixes: c03e7ef12a ("nvme: Implement Write Zeroes")
Reported-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add an helper to access the opaque struct PFlashCFI01.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308131445.17502-9-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Our pflash devices are simplistically modelled has having
"num-blocks" sectors of equal size "sector-length". Real hardware
commonly has sectors of different sizes. How our "sector-length"
property is related to the physical device's multiple sector sizes
is unclear.
Helper functions pflash_cfi01_register() and pflash_cfi02_register()
create a pflash device, set properties including "sector-length" and
"num-blocks", and realize. They take parameters @size, @sector_len
and @nb_blocs.
QOMification left parameter @size unused. Obviously, @size should
match @sector_len and @nb_blocs, i.e. size == sector_len * nb_blocs.
All callers satisfy this.
Remove @nb_blocs and compute it from @size and @sector_len.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-16-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
QOMification left parameter @qdev unused in pflash_cfi01_register()
and pflash_cfi02_register(). All callers pass NULL. Remove.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-15-armbru@redhat.com>
We have two open-coded copies of macro PFLASH_CFI01(). Move the macro
to the header, so we can ditch the copies. Move PFLASH_CFI02() to the
header for symmetry.
We define macros TYPE_PFLASH_CFI01 and TYPE_PFLASH_CFI02 for type name
strings, then mostly use the strings. If the macros are worth
defining, they are worth using. Replace the strings by the macros.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-6-armbru@redhat.com>
pflash_cfi01.c and pflash_cfi02.c start their identifiers with
pflash_cfi01_ and pflash_cfi02_ respectively, except for
CFI_PFLASH01(), TYPE_CFI_PFLASH01, CFI_PFLASH02(), TYPE_CFI_PFLASH02.
Rename for consistency.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-5-armbru@redhat.com>
Our implementation of "write to buffer" (command 0xE8) is flawed.
LOG_UNIMP its use, and add some FIXME comments.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-4-armbru@redhat.com>
When a guest tries to abort "write to buffer" (command 0xE8), we print
"PFLASH: Possible BUG - Write block confirm", then exit(1). Letting
the guest terminate QEMU is not a good idea. Instead, LOG_UNIMP we
screwed up, then reset the device.
Macro PFLASH_BUG() is now unused; delete it.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-3-armbru@redhat.com>
flash.h's incomplete struct pflash_t is completed both in
pflash_cfi01.c and in pflash_cfi02.c. The complete types are
incompatible. This can hide type errors, such as passing a pflash_t
created with pflash_cfi02_register() to pflash_cfi01_get_memory().
Furthermore, POSIX reserves typedef names ending with _t.
Rename the two structs to PFlashCFI01 and PFlashCFI02.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-2-armbru@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-42-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some functions sometimes uses req->dev even though a local variable
VirtIOBlock* s = req->dev has already been defined.
Updated places to use s everywhere in the file.
Signed-off-by: Anastasiia Rusakova <arusakova917@gmail.com>
Message-id: 20190307161925.4158-1-rusakova.nastasia@icloud.com
Message-Id: <20190307161925.4158-1-rusakova.nastasia@icloud.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Don't dynamically allocate the pflash's timer. But do use timer_del in
an unrealize function to make sure that the timer can't fire after the
pflash_t has been freed.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190219153727.62279-1-stephen.checkoway@oberlin.edu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The locally allocated QDict-s need to be freed. ('file_layer' will be
freed implicitly since it is added as an object to 'driver_layer').
Spotted by Coverity: CID 1398649
While in the neighbourhood free 'driver' and 'filename' as soon as they are
added to the QDicts. Freeing after the 'done' label doesn't make that much
sense as, if the error path jumps to that label, the values would be NULL
anyway.
This patch also makes that more obvious by taking the error path if
'params' is NULL and then asserting that both driver and filename are
non-NULL in the normal path.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190219163440.15702-1-paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The function needs to make sure it is passed a valid disk name. This is
easily done by making sure that the parsing loop results in a non-zero
value.
Spotted by Coverity: CID 1398640
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190215162533.19475-4-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The assignment to 'p' is unnecessary as the code will either goto 'invalid'
or p will get overwritten.
Spotted by Coverity: CID 1398638
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190215162533.19475-3-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The if() statement is clearly bogus (dead code which should have been
cleaned up when grant mapping was removed).
Spotted by Coverity: CID 1398635
While in the neighbourhood, add a missing 'fall through' annotation.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190215162533.19475-2-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
- Block graph change fixes (avoid loops, cope with non-tree graphs)
- bdrv_set_aio_context() related fixes
- HMP snapshot commands: Use only tag, not the ID to identify snapshots
- qmeu-img, commit: Error path fixes
- block/nvme: Build fix for gcc 9
- MAINTAINERS updates
- Fix various issues with bdrv_refresh_filename()
- Fix various iotests
- Include LUKS overhead in qemu-img measure for qcow2
- A fix for vmdk's image creation interface
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcc/knAAoJEH8JsnLIjy/WptQP/3F8Lh52H4egXaP7NUUuDjQM
AhqhuDAp/EZBS+xim9kLTogNJADe/rMWdSX/YB5aLpSPYbjasC66NgaLhd6QewgQ
VIcsLUdlYAyZ5ZjJytimfMTLwm1X02RmVIe55y52DTY8LlfViZzOlf3qwqPm00ao
EJB2cl8UJLM+PVEu59cCw3R0/06LY+WIJRB32d3tnCBRTkaJwfR9h4lrp/juVcFZ
U+2eWU68KMbUHSYiWANowN+KRV3uPY4HVA98v3F0vDmcBxlVHOeBg6S+PcT7tK8p
huzCMwcdwUyPMJgVs/+WBtUnbG0jN6SHUYmFLz859UMVgBnCw5tzBMf8qw1wOA4A
Iw+zor27Pxj4IlxcLPp5f97YZ8k9acdMR2VKPH6xLJZ1JF+sKa54RfzESd5EJeIj
Mfcp773H0lIaWcFJ6RY1F0L1E1ta7QigwNBiWMdYfh0a0EWHnDvGyYeaSPYEQ+rl
e8bZOcfrYwVI7DTDiZOIkGA9D8DXEPDNp+sl6s1DxeY69D0NNaXTtCPqFNNAbFbd
20uD7yDRZlWq32cQB/K9D5cSkZRSOzdUpLfLU3nQU2+dz11x6OpM6m7DVboSrztD
1HtPPDzDEvH5dOP7ibd60s+ntjkSiNfNkUgnuVrBE/d/PocC1eHHpZt5V7f43Ofb
RxVwH5+smzQ9nsNBfQR0
=gaah
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- Block graph change fixes (avoid loops, cope with non-tree graphs)
- bdrv_set_aio_context() related fixes
- HMP snapshot commands: Use only tag, not the ID to identify snapshots
- qmeu-img, commit: Error path fixes
- block/nvme: Build fix for gcc 9
- MAINTAINERS updates
- Fix various issues with bdrv_refresh_filename()
- Fix various iotests
- Include LUKS overhead in qemu-img measure for qcow2
- A fix for vmdk's image creation interface
# gpg: Signature made Mon 25 Feb 2019 14:18:15 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (71 commits)
iotests: Skip 211 on insufficient memory
vmdk: false positive of compat6 with hwversion not set
iotests: add LUKS payload overhead to 178 qemu-img measure test
qcow2: include LUKS payload overhead in qemu-img measure
iotests.py: s/_/-/g on keys in qmp_log()
iotests: Let 045 be run concurrently
iotests: Filter SSH paths
iotests.py: Filter filename in any string value
iotests.py: Add is_str()
iotests: Fix 207 to use QMP filters for qmp_log
iotests: Fix 232 for LUKS
iotests: Remove superfluous rm from 232
iotests: Fix 237 for Python 2.x
iotests: Re-add filename filters
iotests: Test json:{} filenames of internal BDSs
block: BDS options may lack the "driver" option
block/null: Generate filename even with latency-ns
block/curl: Implement bdrv_refresh_filename()
block/curl: Harmonize option defaults
block/nvme: Fix bdrv_refresh_filename()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio_blk_dma_restart_bh() submits new requests, so in order to make
sure that these requests are not started inside a drained section of the
attached BlockBackend, we need to make sure that draining the
BlockBackend waits for the BH to be executed.
This BH is still questionable because its scheduled in the main thread
instead of the configured iothread. Leave a FIXME comment for this.
But with this fix, enabling the data plane at least waits for these
requests (in bdrv_set_aio_context()) instead of changing the AioContext
under their feet and making them run in the wrong thread, causing
crashes and failures (e.g. due to missing locking).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the support of DISCARD and WRITE_ZEROES commands,
that have been introduced in the virtio-blk protocol to have
better performance when using SSD backend.
We support only one segment per request since multiple segments
are not widely used and there are no userspace APIs that allow
applications to submit multiple segments in a single call.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-7-sgarzare@redhat.com
Message-Id: <20190221103314.58500-7-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Starting from DISABLE and WRITE_ZEROES features, we use an array of
VirtIOFeature (as virtio-net) to properly set the config size
depending on the features enabled.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-6-sgarzare@redhat.com
Message-Id: <20190221103314.58500-6-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In order to avoid migration issues, we enable DISCARD and
WRITE_ZEROES features only for machine type >= 4.0
As discussed with Michael S. Tsirkin and Stefan Hajnoczi on the
list [1], DISCARD operation should not have security implications
(eg. page cache attacks), so we can enable it by default.
[1] https://lists.gnu.org/archive/html/qemu-devel/2019-02/msg00504.html
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-4-sgarzare@redhat.com
Message-Id: <20190221103314.58500-4-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Since configurable features for virtio-blk are growing, this patch
adds host_features field in the struct VirtIOBlock. (as in virtio-net)
In this way, we can avoid to add new fields for new properties and
we can directly set VIRTIO_BLK_F* flags in the host_features.
We update "config-wce" and "scsi" property definition to use the new
host_features field without change the behaviour.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-3-sgarzare@redhat.com
Message-Id: <20190221103314.58500-3-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We add acct_failed param in order to use virtio_blk_handle_rw_error()
also when is not required to call block_acct_failed(). (eg. a discard
operation is failed)
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-2-sgarzare@redhat.com
Message-Id: <20190221103314.58500-2-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit caa1ee43 "vhost-user-blk: add discard/write zeroes features
support" added fields to struct virtio_blk_config. This changes
the size of the config space and breaks migration from QEMU 3.1
and older:
qemu-system-ppc64: get_pci_config_device: Bad config data: i=0x10 read: 41 device: 1 cmask: ff wmask: 80 w1cmask:0
qemu-system-ppc64: Failed to load PCIDevice:config
qemu-system-ppc64: Failed to load virtio-blk:virtio
qemu-system-ppc64: error while loading state for instance 0x0 of device 'pci@800000020000000:01.0/virtio-blk'
qemu-system-ppc64: load of migration failed: Invalid argument
Since virtio-blk doesn't support the "discard" and "write zeroes"
features, it shouldn't even expose the associated fields in the
config space actually. Just include all fields up to num_queues to
match QEMU 3.1 and older.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1550022537-27565-1-git-send-email-changpeng.liu@intel.com
Message-Id: <1550022537-27565-1-git-send-email-changpeng.liu@intel.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In several part we still using req->dev or VIRTIO_DEVICE(req->dev)
when we have already defined s and vdev pointers:
VirtIOBlock *s = req->dev;
VirtIODevice *vdev = VIRTIO_DEVICE(s);
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 20190208142347.214815-1-sgarzare@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
vhost user blk discard/write zeroes features
misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcWbMUAAoJECgfDbjSjVRp2acH+wa8abfyQIpVMji+cdvcw7Wo
yJjCoPxX0y+tm7FGp6YjyyQhSzjUYRS+71NL6xkZVxs8yh4ZCbb/xDRYmrVG2cb6
6tUcqp1zlMp+w+kVKS4m4WTb0Z1bIODOi99tNBXxYjWY9lXF/hjZbhRpt6vL/NaP
hqYtp+wlhyjxsY/GFn5XZLY7F6+QKq/lsMJD80FvbtHBh/ngqmgyoouNwYzg1faW
M3wD5A3IOXLzU+MGK6uCtKK0+t3xzvaVJL7zChimKkn+y+Pg9T+s04zQS739bJRg
dYYrVK3IOt2tvVxBZnnUm9eBIxxElAxRssmERPe2i0mBRSXYKomuVZrXJ6ROhjA=
=TxWc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, cleanups, features
vhost user blk discard/write zeroes features
misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 05 Feb 2019 16:00:20 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
contrib/libvhost-user: cleanup casts
r2d: fix build on mingw
mmap-alloc: fix hugetlbfs misaligned length in ppc64
mmap-alloc: unfold qemu_ram_mmap()
i386, acpi: cleanup build_facs by removing second unused argument
fw_cfg: fix the life cycle and the name of "qemu_extra_params_fw"
acpi: Make TPM 2.0 with TIS available as MSFT0101
hw/virtio: Use CONFIG_VIRTIO_PCI switch instead of CONFIG_PCI
vhost-user-blk: add discard/write zeroes features support
contrib/vhost-user-blk: fix the compilation issue
pci/msi: export msi_is_masked()
intel_iommu: reset intr_enabled when system reset
intel_iommu: fix operator in vtd_switch_address_space
hw: virtio-pci: drop DO_UPCAST
include: update Linux headers to 4.21-rc1/5.0-rc1
scripts/update-linux-headers.sh: adjust for Linux 4.21-rc1 (or 5.0-rc1)
contrib/libvhost-user: switch to uint64_t
virtio: add checks for the size of the indirect table
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux commit 1f23816b8 "virtio_blk: add discard and write zeroes support"
added the support in the Guest kernel, while here also enable the features
support with vhost-user-blk driver. Also enable the test example utility
with DISCARD and WRITE ZEROES commands.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some frontend drivers will handle dynamic resizing of PV disks, so set up
the BlockDevOps resize_cb() method during xen_block_realize() to allow
this to be done.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
- New debugging QMP command to explore block graphs
- Converted DPRINTF()s to trace events
- Fixed qemu-io's use of getopt() for systems with optreset
- Minor NVMe emulation fixes
- An iotest fix
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcUkaiAAoJEPQH2wBh1c9AHsEIAIU0+FNjtdz7lNgyeBCSFCFa
/qWNk4+w6QBfhTTx/N0hGwh5/FvNYQhby8VHtZitE4/QcLbJwHYgWf14pwce3tP3
3qNB87AdQpKMpbajQM2x2Xy8lnlPeM7fe21Q/12vuX7AlEDT3gH+W9rg94bw2oFN
r+xBk6H5F2aVElw3CwMM7eary4+dPnnCQwAnoqM+g5hdpL+0scrIyARGw7v0hmSn
LDWESCM4a55lEYmwj1wS3J3uj6Fj00yzBvcEuCcT1GO+lXlV8/ciO9r2HqxVKwgz
4GAi/BERoMKjfn+/77/yI5flprPx2voNGgkyBY4C3z9ncnN6u02QBZSusBIWpSg=
=Kt4r
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/xanclic/tags/pull-block-2019-01-31' into staging
Block patches:
- New debugging QMP command to explore block graphs
- Converted DPRINTF()s to trace events
- Fixed qemu-io's use of getopt() for systems with optreset
- Minor NVMe emulation fixes
- An iotest fix
# gpg: Signature made Thu 31 Jan 2019 00:51:46 GMT
# gpg: using RSA key F407DB0061D5CF40
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/xanclic/tags/pull-block-2019-01-31:
iotests: Allow 147 to be run concurrently
iotests: Bind qemu-nbd to localhost in 147
iotests.py: Add qemu_nbd_pipe()
nvme: use pci_dev directly in nvme_realize
nvme: ensure the num_queues is not zero
nvme: use TYPE_NVME instead of constant string
qemu-io: Add generic function for reinitializing optind.
block/sheepdog: Convert from DPRINTF() macro to trace events
block/file-posix: Convert from DPRINTF() macro to trace events
block/curl: Convert from DPRINTF() macro to trace events
block/ssh: Convert from DPRINTF() macro to trace events
scripts: add render_block_graph function for QEMUMachine
qapi: add x-debug-query-block-graph
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no need to make another reference.
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190120055558.32984-4-liq3ea@163.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
When it is zero, it causes segv.
Using following command:
"-drive file=//home/test/test1.img,if=none,id=id0
-device nvme,drive=id0,serial=test,num_queues=0"
causes following Backtrack:
Thread 4 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
[Switching to Thread 0x7fffe9735700 (LWP 30952)]
0x0000555555a7a77c in nvme_start_ctrl (n=0x5555577473f0) at hw/block/nvme.c:825
825 if (unlikely(n->cq[0])) {
(gdb) bt
0 0x0000555555a7a77c in nvme_start_ctrl (n=0x5555577473f0)
at hw/block/nvme.c:825
1 0x0000555555a7af7f in nvme_write_bar (n=0x5555577473f0, offset=20,
data=4587521, size=4) at hw/block/nvme.c:969
2 0x0000555555a7b81a in nvme_mmio_write (opaque=0x5555577473f0, addr=20,
data=4587521, size=4) at hw/block/nvme.c:1163
3 0x0000555555869236 in memory_region_write_accessor (mr=0x555557747cd0,
addr=20, value=0x7fffe97320f8, size=4, shift=0, mask=4294967295, attrs=...)
at /home/test/qemu1/qemu/memory.c:502
4 0x0000555555869446 in access_with_adjusted_size (addr=20,
value=0x7fffe97320f8, size=4, access_size_min=2, access_size_max=8,
access_fn=0x55555586914d <memory_region_write_accessor>,
mr=0x555557747cd0, attrs=...) at /home/test/qemu1/qemu/memory.c:568
5 0x000055555586c479 in memory_region_dispatch_write (mr=0x555557747cd0,
addr=20, data=4587521, size=4, attrs=...)
at /home/test/qemu1/qemu/memory.c:1499
6 0x00005555558030af in flatview_write_continue (fv=0x7fffe0061130,
addr=4273930260, attrs=..., buf=0x7ffff7ff0028 "\001", len=4, addr1=20,
l=4, mr=0x555557747cd0) at /home/test/qemu1/qemu/exec.c:3234
7 0x00005555558031f9 in flatview_write (fv=0x7fffe0061130, addr=4273930260,
attrs=..., buf=0x7ffff7ff0028 "\001", len=4)
at /home/test/qemu1/qemu/exec.c:3273
8 0x00005555558034ff in address_space_write (
---Type <return> to continue, or q <return> to quit---
as=0x555556758480 <address_space_memory>, addr=4273930260, attrs=...,
buf=0x7ffff7ff0028 "\001", len=4) at /home/test/qemu1/qemu/exec.c:3363
9 0x0000555555803550 in address_space_rw (
as=0x555556758480 <address_space_memory>, addr=4273930260, attrs=...,
buf=0x7ffff7ff0028 "\001", len=4, is_write=true)
at /home/test/qemu1/qemu/exec.c:3374
10 0x00005555558884a1 in kvm_cpu_exec (cpu=0x555556920e40)
at /home/test/qemu1/qemu/accel/kvm/kvm-all.c:2031
11 0x000055555584cd9d in qemu_kvm_cpu_thread_fn (arg=0x555556920e40)
at /home/test/qemu1/qemu/cpus.c:1281
12 0x0000555555dbaf6d in qemu_thread_start (args=0x5555569438a0)
at util/qemu-thread-posix.c:502
13 0x00007ffff5dc86db in start_thread (arg=0x7fffe9735700)
at pthread_create.c:463
14 0x00007ffff5af188f in clone ()
at ../sysdeps/unix/sysv/linux/x86_64/clone.S:95
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190120055558.32984-3-liq3ea@163.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190120055558.32984-2-liq3ea@163.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
VirtIOBlock *s is already defined and initialized with req->dev
on top of virtio_blk_handle_request(), so we can remove it from
the code block of VIRTIO_BLK_T_GET_ID case.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190130095231.42081-1-sgarzare@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This should have been removed then xen_disk.c was removed but I missed them.
Fixes: 19f87870ba
xen: remove the legacy 'xen_disk' backend
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190122145132.12571-1-paul.durrant@citrix.com>
[lv: s/stake/stale/ and add "Fixes" tag]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The %lu format string is different depending on the host architecture
which causes builds like the debian-armhf-cross build to fail. Use the
correct PRi64 format string.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190116121350.23863-1-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Memset vhost_dev to zero in the vhost_dev_cleanup function.
This causes dev.vqs to be NULL, so that
vqs does not free up space when calling the g_free function.
This will result in a memory leak. But you can't release vqs
directly in the vhost_dev_cleanup function, because vhost_net
will also call this function, and vhost_net's vqs is assigned by array.
In order to solve this problem, we first save the pointer of vqs,
and release the space of vqs after vhost_dev_cleanup is called.
Signed-off-by: Jian Wang <wangjian161@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The xen-block dataplane currently allocates memory to hold the data for
each request as that request is used, and frees it afterwards. Because
it requires page-aligned blocks, this interacts poorly with non-page-
aligned allocations and balloons the heap.
Instead, allocate the maximum possible buffer size required for the
protocol, which is BLKIF_MAX_SEGMENTS_PER_REQUEST (currently 11) pages
when the request structure is created, and keep that buffer until it is
destroyed. Since the requests are re-used via a free list, this should
actually improve memory usage.
Signed-off-by: Tim Smith <tim.smith@citrix.com>
Re-based and commit comment adjusted.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
If the I/O ring is full, the guest cannot send any more requests
until some responses are sent. Only sending all available responses
just before checking for new work does not leave much time for the
guest to supply new work, so this will cause stalls if the ring gets
full. Also, not completing reads as soon as possible adds latency
to the guest.
To alleviate that, complete IO requests as soon as they come back.
xen_block_send_response() already returns a value indicating whether
a notify should be sent, which is all the batching we need.
Signed-off-by: Tim Smith <tim.smith@citrix.com>
Re-based and commit comment adjusted.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
When I/O consists of many small requests, performance is improved by
batching them together in a single io_submit() call. When there are
relatively few requests, the extra overhead is not worth it. This
introduces a check to start batching I/O requests via blk_io_plug()/
blk_io_unplug() in an amount proportional to the number which were
already in flight at the time we started reading the ring.
Signed-off-by: Tim Smith <tim.smith@citrix.com>
Re-based and commit comment adjusted.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This backend has now been replaced by the 'xen-qdisk' XenDevice.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds create and destroy function for XenBlockDevice-s so that
they can be created automatically when the Xen toolstack instantiates a new
PV backend via xenstore. When the XenBlockDevice is created this way it is
also necessary to create a 'drive' which matches the configuration that the
Xen toolstack has written into xenstore. This is done by formulating the
parameters necessary for each 'blockdev' layer of the drive and then using
qmp_blockdev_add() to create the layers. Also, for compatibility with the
legacy 'xen_disk' implementation, an iothread is automatically created for
the new XenBlockDevice. This, like the driver layers, will be destroyed
after the XenBlockDevice is unrealized.
The legacy backend scan for 'qdisk' is removed by this patch, which makes
the 'xen_disk' code is redundant. The code will be removed by a subsequent
patch.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and wire in the dataplane.
This patch adds the remaining code to make the xen-block XenDevice
functional. The parameters that a block frontend expects to find are
populated in the backend xenstore area, and the 'ring-ref' and
'event-channel' values specified in the frontend xenstore area are
mapped/bound and used to set up the dataplane.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This is a purely cosmetic patch that purges remaining use of 'blk' and
'ioreq' in local function names, and then makes sure all functions are
prefixed with 'xen_block_'.
No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This is a purely cosmetic patch that purges the name 'ioreq' from struct,
variable and field names. (This name has been problematic for a long time
as 'ioreq' is the name used for generic I/O requests coming from Xen).
The patch replaces 'struct ioreq' with a new 'XenBlockRequest' type and
'ioreq' field/variable names with 'request', and then does necessary
fix-up to adhere to coding style.
Function names are not modified by this patch. They will be dealt with in
a subsequent patch.
No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
