vmxnet3 has no dependency on PC, and VMware Fusion actually makes it
available on Apple Silicon according to:
https://kb.vmware.com/s/article/90364
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
For GPIE.NSICR, Section 7.3.2.1.2 says:
> ICR bits are cleared on register read. If GPIE.NSICR = 0b, then the
> clear on read occurs only if no bit is set in the IMS or at least one
> bit is set in the IMS and there is a true interrupt as reflected in
> ICR.INTA.
e1000e does similar though it checks for CTRL_EXT.IAME, which does not
exist on igb.
Suggested-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This follows the corresponding change for e1000e. This fixes:
tests/avocado/netdev-ethtool.py:NetDevEthtool.test_igb
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In MSI-X mode, if there are interrupts already notified but not cleared
and a new interrupt arrives, e1000e incorrectly notifies the notified
ones again along with the new one.
To fix this issue, replace e1000e_update_interrupt_state() with
two new functions: e1000e_raise_interrupts() and
e1000e_lower_interrupts(). These functions don't only raise or lower
interrupts, but it also performs register writes which updates the
interrupt state. Before it performs a register write, these function
determines the interrupts already raised, and compares with the
interrupts raised after the register write to determine the interrupts
to notify.
The introduction of these functions made tracepoints which assumes that
the caller of e1000e_update_interrupt_state() performs register writes
obsolete. These tracepoints are now removed, and alternative ones are
added to the new functions.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb has a configurable size limit for LPE, and uses different limits
depending on whether the packet is treated as a VLAN packet.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e does not support using UDP for RSS hash, but igb does.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
eth_strip_vlan and eth_strip_vlan_ex refers to ehdr_buf as struct
eth_header. Enforce alignment for the structure.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
It is possible to have another VLAN tag even if the packet is already
tagged.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Rename variable "n" to "causes", which properly represents the content
of the variable.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Rename variable "n" to "causes", which properly represents the content
of the variable.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 7.3.4.1 says:
> When auto-clear is enabled for an interrupt cause, the EICR bit is
> set when a cause event mapped to this vector occurs. When the EITR
> Counter reaches zero, the MSI-X message is sent on PCIe. Then the
> EICR bit is cleared and enabled to be set by a new cause event
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The constants need to be consistent between the PF and VF.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Keeping Tx packet state after the transmit queue is emptied but this
behavior is unreliable as the state can be reset anytime the migration
happens.
Always reset Tx packet state always after the queue is emptied.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Keeping Tx packet state after the transmit queue is emptied has some
problems:
- The datasheet says the descriptors can be reused after the transmit
queue is emptied, but the Tx packet state may keep references to them.
- The Tx packet state cannot be migrated so it can be reset anytime the
migration happens.
Always reset Tx packet state always after the queue is emptied.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 7.2.2.3 Advanced Transmit Data Descriptor says:
> For frames that spans multiple descriptors, all fields apart from
> DCMD.EOP, DCMD.RS, DCMD.DEXT, DTALEN, Address and DTYP are valid only
> in the first descriptors and are ignored in the subsequent ones.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The goto is a bit confusing as it changes the control flow only if L4
protocol is not recognized. It is also different from e1000e, and
noisy when comparing e1000e and igb.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Without this change, the status flags may not be traced e.g. if checksum
offloading is disabled.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Without this change, the status flags may not be traced e.g. if checksum
offloading is disabled.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e and igb employs NetPktRssIpV6TcpEx for RSS hash if TcpIpv6 MRQC
bit is set. Moreover, igb also has a MRQC bit for NetPktRssIpV6Tcp
though it is not implemented yet. Rename it to TcpIpv6Ex to avoid
confusion.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 13.7.15 Receive Length Error Count says:
> Packets over 1522 bytes are oversized if LongPacketEnable is 0b
> (RCTL.LPE). If LongPacketEnable (LPE) is 1b, then an incoming packet
> is considered oversized if it exceeds 16384 bytes.
> These lengths are based on bytes in the received packet from
> <Destination Address> through <CRC>, inclusively.
As QEMU processes packets without CRC, the number of bytes for CRC
need to be subtracted. This change adds some size definitions to be used
to derive the new size thresholds to eth.h.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This saves some code and enables tracepoint for e1000's VLAN filtering.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The old eth_setup_vlan_headers has no user so remove it and rename
eth_setup_vlan_headers_ex.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb_receive_internal() used to check the iov length to determine
copy the iovs to a contiguous buffer, but the check is flawed in two
ways:
- It does not ensure that iovcnt > 0.
- It does not take virtio-net header into consideration.
The size of this copy is just 22 octets, which can be even less than
the code size required for checks. This (wrong) optimization is probably
not worth so just remove it. Removing this also allows igb to assume
aligned accesses for the ethernet header.
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e_receive_internal() used to check the iov length to determine
copy the iovs to a contiguous buffer, but the check is flawed in two
ways:
- It does not ensure that iovcnt > 0.
- It does not take virtio-net header into consideration.
The size of this copy is just 18 octets, which can be even less than
the code size required for checks. This (wrong) optimization is probably
not worth so just remove it.
Fixes: 6f3fbe4ed0 ("net: Introduce e1000e device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb does not properly ensure the buffer passed to
net_rx_pkt_set_protocols() is contiguous for the entire L2/L3/L4 header.
Allow it to pass scattered data to net_rx_pkt_set_protocols().
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The datasheet says contradicting statements regarding ICR accesses so it
is not reliable to determine the behavior of ICR accesses. However,
e1000e does clear IMS bits when reading ICR accesses and Linux also
expects ICR accesses will clear IMS bits according to:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/intel/igb/igb_main.c?h=v6.2#n8048
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
While the datasheet of e1000e says it checks CTRL.VME for tx VLAN
tagging, igb's datasheet has no such statements. It also says for
"CTRL.VLE":
> This register only affects the VLAN Strip in Rx it does not have any
> influence in the Tx path in the 82576.
(Appendix A. Changes from the 82575)
There is no "CTRL.VLE" so it is more likely that it is a mistake of
CTRL.VME.
Fixes: fba7c3b788 ("igb: respect VMVIR and VMOLR for VLAN")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb's advanced descriptor uses a packet type encoding different from
one used in e1000e's extended descriptor. Fix the logic to encode
Rx packet type accordingly.
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Before this change, e1000 and the common code updated BPRC and MPRC
depending on the matched filter, but e1000e and igb decided to update
those counters by deriving the packet type independently. This
inconsistency caused a multicast packet to be counted twice.
Updating BPRC and MPRC depending on are fundamentally flawed anyway as
a filter can be used for different types of packets. For example, it is
possible to filter broadcast packets with MTA.
Always determine what counters to update by inspecting the packets.
Fixes: 3b27430177 ("e1000: Implementing various counters")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This allows to use the network packet abstractions even if PCI is not
used.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is intended to be followed by another change for the interface.
It also fixes the leak of memory mapping when the specified memory is
partially mapped.
Fixes: e263cd49c7 ("Packet abstraction for VMWARE network devices")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The bytes and packets counter registers are cleared on read.
Copying the "total counter" registers to the "good counter" registers has
side effects.
If the "total" register is never read by the OS, it only gets incremented.
This leads to exponential growth of the "good" register.
This commit increments the counters individually to avoid this.
Signed-off-by: Timothée Cocault <timothee.cocault@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The commit 93a97dc520 ("virtio-net: enable vq reset feature") enables
unconditionally vq reset feature as long as the device is emulated.
This makes impossible to actually disable the feature, and it causes
migration problems from qemu version previous than 7.2.
The entire final commit is unneeded as device system already enable or
disable the feature properly.
This reverts commit 93a97dc520.
Fixes: 93a97dc520 ("virtio-net: enable vq reset feature")
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230504101447.389398-1-eperezma@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that the tswap() functions are available for target-independent
code, too, we can move xilinx_ethlite.c from specific_ss to softmmu_ss
to avoid that we have to compile this file multiple times.
Message-Id: <20230508120314.59274-1-thuth@redhat.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
In allwinner-sun8i-emac we just read directly from guest memory into
a host FrameDescriptor struct and back. This only works on
little-endian hosts. Reading and writing of descriptors is already
abstracted into functions; make those functions also handle the
byte-swapping so that TransferDescriptor structs as seen by the rest
of the code are always in host-order, and fix two places that were
doing ad-hoc descriptor reading without using the functions.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230424165053.1428857-3-peter.maydell@linaro.org
The msf2-emac ethernet controller has functions emac_load_desc() and
emac_store_desc() which read and write the in-memory descriptor
blocks and handle conversion between guest and host endianness.
As currently written, emac_store_desc() does the endianness
conversion in-place; this means that it effectively consumes the
input EmacDesc struct, because on a big-endian host the fields will
be overwritten with the little-endian versions of their values.
Unfortunately, in all the callsites the code continues to access
fields in the EmacDesc struct after it has called emac_store_desc()
-- specifically, it looks at the d.next field.
The effect of this is that on a big-endian host networking doesn't
work because the address of the next descriptor is corrupted.
We could fix this by making the callsite avoid using the struct; but
it's more robust to have emac_store_desc() leave its input alone.
(emac_load_desc() also does an in-place conversion, but here this is
fine, because the function is supposed to be initializing the
struct.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20230424151919.1333299-1-peter.maydell@linaro.org
The MAC address set from Qemu wasn't being saved into the register space.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: moved variable declaration to top of function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This protects devices from bh->mmio reentrancy issues.
Thanks: Thomas Huth <thuth@redhat.com> for diagnosing OS X test failure.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230427211013.2994127-5-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The SOC on i.MX6UL and i.MX7 has 2 Ethernet interfaces. The PHY on each may
be connected to separate MDIO busses, or both may be connected on the same
MDIO bus using different PHY addresses. Commit 461c51ad42 ("Add a phy-num
property to the i.MX FEC emulator") added support for specifying PHY
addresses, but it did not provide support for linking the second PHY on
a given MDIO bus to the other Ethernet interface.
To be able to support two PHY instances on a single MDIO bus, two properties
are needed: First, there needs to be a flag indicating if the MDIO bus on
a given Ethernet interface is connected. If not, attempts to read from this
bus must always return 0xffff. Implement this property as phy-connected.
Second, if the MDIO bus on an interface is active, it needs a link to the
consumer interface to be able to provide PHY access for it. Implement this
property as phy-consumer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20230315145248.1639364-2-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
