This includes in QEMU a new CPU model for the POWER10 processor with
the same capabilities of a POWER9 process. The model will be extended
when support is completed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a CPU is reset, QEMU makes sure no interrupt is pending by clearing
CPUPPCstate::pending_interrupts in ppc_cpu_reset(). In the case of a
complete machine emulation, eg. a sPAPR machine, an external interrupt
request could still be pending in KVM though, eg. an IPI. It will be
eventually presented to the guest, which is supposed to acknowledge it at
the interrupt controller. If the interrupt controller is emulated in QEMU,
either XICS or XIVE, ppc_set_irq() won't deassert the external interrupt
pin in KVM since it isn't pending anymore for QEMU. When the vCPU re-enters
the guest, the interrupt request is still pending and the vCPU will try
again to acknowledge it. This causes an infinite loop and eventually hangs
the guest.
The code has been broken since the beginning. The issue wasn't hit before
because accel=kvm,kernel-irqchip=off is an awkward setup that never got
used until recently with the LC92x IBM systems (aka, Boston).
Add a ppc_irq_reset() function to do the necessary cleanup, ie. deassert
the IRQ pins of the CPU in QEMU and most importantly the external interrupt
pin for this vCPU in KVM.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157548861740.3650476.16879693165328764758.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER8 systems the Directed Privileged Door-bell Exception State
register (DPDES) stores doorbell pending status, one bit per a thread
of a core, set by "msgsndp" instruction. The register is shared among
threads of the same core and KVM on POWER9 emulates it in a similar way
(POWER9 does not have DPDES).
DPDES is shared but QEMU assumes all SPRs are per thread so the only safe
way to write DPDES back to VCPU before running a guest is doing so
while all threads are pulled out of the guest so DPDES cannot change.
There is only one situation when this condition is met: incoming migration
when all threads are stopped. Otherwise any QEMU HMP/QMP command causing
kvm_arch_put_registers() (for example printing registers or dumping memory)
can clobber DPDES in a race with other vcpu threads.
This changes DPDES handling so it is not written to KVM at runtime.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190923084110.34643-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ibm,get_system_parameter rtas call is used by the guest to retrieve
data relating to certain parameters of the system. The SPLPAR
characteristics option (token 20) is used to determine characteristics of
the environment in which the lpar will run.
It may be useful for a guest to know the number of physical host threads
present on the underlying system where it is being run. Add the
characteristic "HostThrs" to the SPLPAR Characteristics
ibm,get_system_parameter rtas call to expose this information to a
guest. Add a n_host_threads property to the processor class which is
then used to retrieve this information and define it for POWER8 and
POWER9. Other processors will default to 0 and the charateristic won't
be added.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190827045751.22123-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As defined in Power 3.0 section 4.4.4 "Underflow Exception",
a tiny result is detected before rounding.
Fixes: https://bugs.launchpad.net/qemu/+bug/1841491
Reported-by: Paul Clarke <pc@us.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190827020013.27154-1-richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
First ppc and spapr pull request for qemu-4.2. Includes:
* Some TCG emulation fixes and performance improvements
* Support for the mffsl instruction in TCG
* Added missing DPDES SPR
* Some enhancements to the emulation of the XIVE interrupt
controller
* Cleanups to spapr MSI management
* Some new suspend/resume infrastructure and a draft suspend
implementation for spapr
* New spapr hypercall for TPM communication (will be needed for
secure guests under an Ultravisor)
* Fix several memory leaks
And a few other assorted fixes.
-----BEGIN PGP SIGNATURE-----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=E+7d
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20190821' into staging
ppc patch queue for 2019-08-21
First ppc and spapr pull request for qemu-4.2. Includes:
* Some TCG emulation fixes and performance improvements
* Support for the mffsl instruction in TCG
* Added missing DPDES SPR
* Some enhancements to the emulation of the XIVE interrupt
controller
* Cleanups to spapr MSI management
* Some new suspend/resume infrastructure and a draft suspend
implementation for spapr
* New spapr hypercall for TPM communication (will be needed for
secure guests under an Ultravisor)
* Fix several memory leaks
And a few other assorted fixes.
# gpg: Signature made Wed 21 Aug 2019 08:24:44 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20190821: (42 commits)
ppc: Fix emulated single to double denormalized conversions
ppc: Fix emulated INFINITY and NAN conversions
ppc: conform to processor User's Manual for xscvdpspn
ppc: Add support for 'mffsl' instruction
target/ppc: Add Directed Privileged Door-bell Exception State (DPDES) SPR
spapr/xive: Mask the EAS when allocating an IRQ
spapr: Implement better workaround in spapr-vty device
spapr/irq: Drop spapr_irq_msi_reset()
spapr/pci: Free MSIs during reset
spapr/pci: Consolidate de-allocation of MSIs
ppc: remove idle_timer logic
spapr: Implement ibm,suspend-me
i386: use machine class ->wakeup method
machine: Add wakeup method to MachineClass
ppc/xive: Improve 'info pic' support
ppc/xive: Provide silent escalation support
ppc/xive: Provide unconditional escalation support
ppc/xive: Provide escalation support
ppc/xive: Provide backlog support
ppc/xive: Implement TM_PULL_OS_CTX special command
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
DPDES stores a status of a doorbell message and if it is lost in
migration, the destination CPU won't receive it. This does not hit us
much as IPIs complete too quick to catch a pending one and even if
we missed one, broadcasts happen often enough to wake that CPU.
This defines DPDES and registers with KVM for migration.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190816061733.53572-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Implement cpu_exec_enter/exit on ppc which calls into new methods of
the same name in PPCVirtualHypervisorClass. These are used by spapr
to implement the splpar VPA dispatch counter initially.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-2-npiggin@gmail.com>
[dwg: Removed unnecessary CONFIG_USER_ONLY checks as suggested by gkurz]
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The opcode decode tables aren't really part of the CPUPPCState but an
internal implementation detail for the translator. This can cause
problems with memcpy in cpu_copy as any table created during
ppc_cpu_realize get written over causing a memory leak. To avoid this
move the tables into PowerPCCPU which is better suited to hold
internal implementation details.
Attempts to fix: https://bugs.launchpad.net/qemu/+bug/1836558
Cc: 1836558@bugs.launchpad.net
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190716121352.302-1-alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Prior patch resets can_do_io flag at the TB entry. Therefore there is no
need in resetting this flag at the end of the block.
This patch removes redundant gen_io_end calls.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Message-Id: <156404429499.18669.13404064982854123855.stgit@pasha-Precision-3630-Tower>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@gmail.com>
Move commands query-cpu-definitions, query-cpu-model-baseline,
query-cpu-model-comparison, and query-cpu-model-expansion with their
types from target.json to machine-target.json. Also move types
CpuModelInfo, CpuModelExpansionType, and CpuModelCompareResult from
misc.json there. Add machine-target.json to MAINTAINERS section
"Machine core".
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-13-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[Commit message typo fixed]
Other accelerators have their own headers: sysemu/hax.h, sysemu/hvf.h,
sysemu/kvm.h, sysemu/whpx.h. Only tcg_enabled() & friends sit in
qemu-common.h. This necessitates inclusion of qemu-common.h into
headers, which is against the rules spelled out in qemu-common.h's
file comment.
Move tcg_enabled() & friends into their own header sysemu/tcg.h, and
adjust #include directives.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Rebased with conflicts resolved automatically, except for
accel/tcg/tcg-all.c]
Consolidate some boilerplate from foo_cpu_initfn.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace ppc_env_get_cpu with env_archcpu. The combination
CPU(ppc_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cc: qemu-ppc@nongnu.org
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Commit dc99065b5f (v0.1.0) added dis-asm.h from binutils.
Commit 43d4145a98 (v0.1.5) inlined bfd.h into dis-asm.h to remove the
dependency on binutils.
Commit 76cad71136 (v1.4.0) moved dis-asm.h to include/disas/bfd.h.
The new name is confusing when you try to match against (pre GPLv3+)
binutils. Rename it back. Keep it in the same directory, of course.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417191805.28198-17-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The various TARGET_cpu_list() take an fprintf()-like callback and a
FILE * to pass to it. Their callers (vl.c's main() via list_cpus(),
bsd-user/main.c's main(), linux-user/main.c's main()) all pass
fprintf() and stdout. Thus, the flexibility provided by the (rather
tiresome) indirection isn't actually used.
Drop the callback, and call qemu_printf() instead.
Calling printf() would also work, but would make the code unsuitable
for monitor context without making it simpler.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417191805.28198-10-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We now have enough support to boot a PowerNV machine with a POWER9
processor. Allow HV mode on POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-16-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Prior to POWER9 the decrementer was a 32-bit register which decremented
with each tick of the timebase. From POWER9 onwards the decrementer can
be set to operate in a mode called large decrementer where it acts as a
n-bit decrementing register which is visible as a 64-bit register, that
is the value of the decrementer is sign extended to 64 bits (where n is
implementation dependant).
The mode in which the decrementer operates is controlled by the LPCR_LD
bit in the logical paritition control register (LPCR).
>From POWER9 onwards the HDEC (hypervisor decrementer) was enlarged to
h-bits, also sign extended to 64 bits (where h is implementation
dependant). Note this isn't configurable and is always enabled.
On POWER9 the large decrementer and hdec are both 56 bits, as
represented by the lrg_decr_bits cpu class property. Since they are the
same size we only add one property for now, which could be extended in
the case they ever differ in the future.
We also add the lrg_decr_bits property for POWER5+/7/8 since it is used
to determine the size of the hdec, which is only generated on the
POWER5+ processor and later. On these processors it is 32 bits.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190301024317.22137-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Our TCG TLB only tags whether it's a HV vs a guest access, so it must
be flushed when the LPIDR is changed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215170029.15641-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This controls whether the External Interrupt (0x500) can be
delivered to the hypervisor or not.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190215161648.9600-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Adds support for the Hypervisor directed interrupts in addition to the
OS ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - modified the icp_realize() and xive_tctx_realize() to take
into account explicitely the POWER9 interrupt model
- introduced a specific power9_set_irq for POWER9 ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215161648.9600-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This adds support for delivering that exception
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190215161648.9600-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
And use it to get the correct HILE bit in HID0
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190215161648.9600-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
STOP must act differently based on PSSCR:EC on POWER9. When set, it
acts like the P7/P8 power management instructions and wake up at 0x100
based on the wakeup conditions in LPCR.
When PSSCR:EC is clear however it will wakeup at the next instruction
after STOP (if EE is clear) or take the corresponding interrupts (if
EE is set).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190215161648.9600-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Here's the next batch of ppc and spapr patches. Higlights are:
* A bunch of improvements to TCG handling of vector instructions from
Richard Henderson and Marc Cave-Ayland
* Cleanup to the XICS interrupt controller from Greg Kurz, removing
the special KVM subclasses which were a bad idea
* Some refinements to the XIVE interrupt controller from Cédric Le
Goater
* Fix from Fabiano Rosas for a really dumb buffer overflow in the
device tree code for memory hotplug
* Code for allowing access to SPRs from the gdb stub from Fabiano
Rosas
* Assorted minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=QQra
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.0-20190219' into staging
ppc patch queue 2019-02-19
Here's the next batch of ppc and spapr patches. Higlights are:
* A bunch of improvements to TCG handling of vector instructions from
Richard Henderson and Marc Cave-Ayland
* Cleanup to the XICS interrupt controller from Greg Kurz, removing
the special KVM subclasses which were a bad idea
* Some refinements to the XIVE interrupt controller from Cédric Le
Goater
* Fix from Fabiano Rosas for a really dumb buffer overflow in the
device tree code for memory hotplug
* Code for allowing access to SPRs from the gdb stub from Fabiano
Rosas
* Assorted minor fixes and cleanups
# gpg: Signature made Mon 18 Feb 2019 13:47:54 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.0-20190219: (43 commits)
target/ppc: convert vmin* and vmax* to vector operations
target/ppc: convert vadd*s and vsub*s to vector operations
target/ppc: Split out VSCR_SAT to a vector field
target/ppc: Add set_vscr_sat
target/ppc: Use mtvscr/mfvscr for vmstate
target/ppc: Add helper_mfvscr
target/ppc: Remove vscr_nj and vscr_sat
target/ppc: Use helper_mtvscr for reset and gdb
target/ppc: Pass integer to helper_mtvscr
target/ppc: convert xxsel to vector operations
target/ppc: convert xxspltw to vector operations
target/ppc: convert xxspltib to vector operations
target/ppc: convert VSX logical operations to vector operations
target/ppc: convert vsplt[bhw] to use vector operations
target/ppc: convert vspltis[bhw] to use vector operations
target/ppc: convert vaddu[b,h,w,d] and vsubu[b,h,w,d] over to use vector operations
target/ppc: convert VMX logical instructions to use vector operations
xics: Drop the KVM ICS class
spapr/irq: Use the "simple" ICS class for KVM
xics: Handle KVM interrupt presentation from "simple" ICS code
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is required before changing the representation of the register.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190215100058.20015-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Not setting flush_to_zero from gdb_set_avr_reg was a bug.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190215100058.20015-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ISA 2.06/2.07 Power Management instructions (doze, nap & rvwinkle)
don't exist on POWER9, don't enable them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190128094625.4428-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows reading and writing of SPRs via GDB:
(gdb) p/x $srr1
$1 = 0x8000000002803033
(gdb) p/x $pvr
$2 = 0x4b0201
(gdb) set $pvr=0x4b0000
(gdb) p/x $pvr
$3 = 0x4b0000
The `info` command can also be used:
(gdb) info registers spr
For this purpose, GDB needs to be provided with an XML description of
the registers (see the gdb-xml directory for examples) and a set of
callbacks for reading and writing the registers must be defined.
The XML file in this case is created dynamically, based on the SPRs
already defined in the machine. This way we avoid the need for several
XML files to suit each possible ppc machine.
The gdb_{get,set}_spr_reg callbacks take an index based on the order
the registers appear in the XML file. This index does not match the
actual location of the registers in the env->spr array so the
gdb_find_spr_idx function does that conversion.
Note: GDB currently needs to know the guest endianness in order to
properly print the registers values. This is done automatically by GDB
when provided with the ELF file or explicitly with the `set endian
<big|little>` command.
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using the e6500 CPU, QEMU generates a fatal error after
complaining about registering SPR 604 twice.
Building and testing with commit
9b2e891ec5 shows the issue:
qemu-system-ppc64 --version
QEMU emulator version 3.1.50 (v3.1.0-456-g9b2e891ec5-dirty)
Copyright (c) 2003-2018 Fabrice Bellard and the QEMU Project developers
qemu-system-ppc64 -M none -cpu e6500
Error: Trying to register SPR 604 (25c) twice !
Signed-off-by: Jon Diekema <jon.diekema@ge.com>
Message-Id: <CALvuzg43uSodseEHjNaRcPFBKKPTY2mcppUbYgiLL=QO9RxX_Q@mail.gmail.com>
[removed duplicated mail header in the commit message]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The VSX register array is a block of 64 128-bit registers where the first 32
registers consist of the existing 64-bit FP registers extended to 128-bit
using new VSR registers, and the last 32 registers are the VMX 128-bit
registers as show below:
64-bit 64-bit
+--------------------+--------------------+
| FP0 | | VSR0
+--------------------+--------------------+
| FP1 | | VSR1
+--------------------+--------------------+
| ... | ... | ...
+--------------------+--------------------+
| FP30 | | VSR30
+--------------------+--------------------+
| FP31 | | VSR31
+--------------------+--------------------+
| VMX0 | VSR32
+-----------------------------------------+
| VMX1 | VSR33
+-----------------------------------------+
| ... | ...
+-----------------------------------------+
| VMX30 | VSR62
+-----------------------------------------+
| VMX31 | VSR63
+-----------------------------------------+
In order to allow for future conversion of VSX instructions to use TCG vector
operations, recreate the same layout using an aligned version of the existing
vsr register array.
Since the old fpr and avr register arrays are removed, the existing callers
must also be updated to use the correct offset in the vsr register array. This
also includes switching the relevant VMState fields over to using subarrays
to make sure that migration is preserved.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Because it is a recommended coding practice (see HACKING).
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ptcr (partition table control register) is used to store the address
and size of the partition table. For nested kvm-hv we have a level 1
guest register the location of it's partition table with the hypervisor.
Thus to support migration we need to be able to read this out of kvm
and restore it post migration.
Add the one reg id for the ptcr.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
External PID is a mechanism present on BookE 2.06 that enables application to
store/load data from different address spaces. There are special version of some
instructions, which operate on alternate address space, which is specified in
the EPLC/EPSC regiser.
This implementation uses two additional MMU modes (mmu_idx) to provide the
address space for the load and store instructions. The QEMU TLB fill code was
modified to recognize these MMU modes and use the values in EPLC/EPSC to find
the proper entry in he PPC TLB. These two QEMU TLBs are also flushed on each
write to EPLC/EPSC.
Following instructions are implemented: dcbfep dcbstep dcbtep dcbtstep dcbzep
dcbzlep icbiep lbepx ldepx lfdepx lhepx lwepx stbepx stdepx stfdepx sthepx
stwepx.
Following vector instructions are not: evlddepx evstddepx lvepx lvepxl stvepx
stvepxl.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Calling error_report() in a function that takes an Error ** argument
is suspicious. Convert a few that are actually warnings to
warn_report().
While there, split a warning consisting of multiple sentences to
conform to conventions spelled out in warn_report()'s contract.
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Fam Zheng <famz@redhat.com>
Cc: Wei Huang <wei@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20181017082702.5581-5-armbru@redhat.com>
There is no known available OS for ppc around anymore that uses page
sizes below 4k, so it does not make much sense that we keep wasting
our time on building and testing the ppcemb-softmmu target. It has
been deprecated since two releases, and nobody complained, so let's
remove this now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add support for DBCR (debug control register) based debugging as used on
BookE ppc. So far supports only branch and single-step events, but these are
the important ones. GDB in Linux guest can now do single-stepping.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
While just setting the MSR bits is sufficient, we can tidy
the helper code by extracting the MSR test to a helper and
then forcing it true for user-only.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows faults from MO_ALIGN to have the same effect
as from gen_check_align.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
CPUPPCState currently contains a number of fields containing the state of
the VPA. The VPA is a PAPR specific concept covering several guest/host
shared memory areas used to communicate some information with the
hypervisor.
As a PAPR concept this is really machine specific information, although it
is per-cpu, so it doesn't really belong in the core CPU state structure.
There's also other information that's per-cpu, but platform/machine
specific. So create a (void *)machine_data in PowerPCCPU which can be
used by the machine to locate per-cpu data. Intialization, lifetime and
cleanup of machine_data is entirely up to the machine type.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
According to PowerISA, the PIR register should be readable in privileged
mode also, not only in hypervisor privileged mode.
PowerISA 3.0 - 4.3.3 Processor Identification Register
"Read access to the PIR is privileged; write access is not provided."
Figure 18 in section 4.4.4 explicitly confirms that mfspr PIR is privileged
and doesn't require hypervisor state.
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: qemu-ppc@nongnu.org
Signed-off-by: Leandro Lupori <leandro.lupori@gmail.com>
Reviewed-by: Jose Ricardo Ziviani <joserz@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The powerpc Linux kernel[1] and skiboot firmware[2] recently gained changes
that cause the Processor Compatibility Register (PCR) SPR to be cleared.
These changes cause Linux to fail to boot on the Qemu powernv machine
with an error:
Trying to write privileged spr 338 (0x152) at 0000000030017f0c
With this patch Qemu makes this register available as a hypervisor
privileged register.
Note that bits set in this register disable features of the processor.
Currently the only register state that is supported is when the register
is zeroed (enable all features). This is sufficient for guests to
once again boot.
[1] https://lkml.kernel.org/r/20180518013742.24095-1-mikey@neuling.org
[2] https://patchwork.ozlabs.org/patch/915932/
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Rename the 2.13 machines to match the number we're going to
use for the next release.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-id: 20180522104000.9044-5-peter.maydell@linaro.org
osdep.h is only needed for files that are compiled directly.
Remove it from included C source files, and rename them to
*.inc.c so that scripts/clean-includes knows to skip them.
Cc: Eric Blake <eblake@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
