object_get_canonical_path_component() returns a malloced copy of a
property name on success, null on failure.
19 of its 25 callers immediately free the returned copy.
Change object_get_canonical_path_component() to return the property
name directly. Since modifying the name would be wrong, adjust the
return type to const char *.
Drop the free from the 19 callers become simpler, add the g_strdup()
to the other six.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200714160202.3121879-4-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
In armsse_realize() we have a loop over [0, info->num_cpus), which
indexes into various fixed-size arrays in the ARMSSE struct. This
confuses Coverity, which warns that we might overrun those arrays
(CID 1430326, 1430337, 1430371, 1430414, 1430430). This can't
actually happen, because the info struct is always one of the entries
in the armsse_variants[] array and num_cpus is either 1 or 2; we also
already assert in armsse_init() that num_cpus is not too large.
However, adding an assert to armsse_realize() like the one in
armsse_init() should help Coverity figure out that these code paths
aren't possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200713143716.9881-1-peter.maydell@linaro.org
The doc-comments which document the qdev API are split between the
header file and the C source files, because as a project we haven't
been consistent about where we put them.
Move all the doc-comments in qdev.c to the header files, so that
users of the APIs don't have to look at the implementation files for
this information.
In the process, unify them into our doc-comment format and expand on
them in some cases to clarify expected use cases.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200711142425.16283-2-peter.maydell@linaro.org
When MTE is enabled, tag memory must exist for all RAM.
It might be possible to simultaneously hot plug tag memory
alongside the corresponding normal memory, but for now just
disable hotplug.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200713213341.590275-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While we expect KVM to support MTE at some future point,
it certainly won't be ready in time for qemu 5.1.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200713213341.590275-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Control this cpu feature via a machine property, much as we do
with secure=on, since both require specialized support in the
machine setup to be functional.
Default MTE to off, since this feature implies extra overhead.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200713213341.590275-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here are some assorted fixes for qemu-5.1:
* SLOF update with improved TPM handling, and fix for possible stack
overflows on many-vcpu machines
* Fix for NUMA distances on NVLink2 attached GPU memory nodes
* Fixes to fail more gracefully on attempting to plug unsupported PCI bridge types
* Don't allow pnv-psi device to be user created
-----BEGIN PGP SIGNATURE-----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=CYAQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.1-20200720' into staging
ppc patch queue 20200720
Here are some assorted fixes for qemu-5.1:
* SLOF update with improved TPM handling, and fix for possible stack
overflows on many-vcpu machines
* Fix for NUMA distances on NVLink2 attached GPU memory nodes
* Fixes to fail more gracefully on attempting to plug unsupported PCI bridge types
* Don't allow pnv-psi device to be user created
# gpg: Signature made Mon 20 Jul 2020 06:29:21 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.1-20200720:
pseries: Update SLOF firmware image
spapr: Add a new level of NUMA for GPUs
spapr_pci: Robustify support of PCI bridges
ppc/pnv: Make PSI device types not user creatable
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
NUMA nodes corresponding to GPU memory currently have the same
affinity/distance as normal memory nodes. Add a third NUMA associativity
reference point enabling us to give GPU nodes more distance.
This is guest visible information, which shouldn't change under a
running guest across migration between different qemu versions, so make
the change effective only in new (pseries > 5.0) machine types.
Before, `numactl -H` output in a guest with 4 GPUs (nodes 2-5):
node distances:
node 0 1 2 3 4 5
0: 10 40 40 40 40 40
1: 40 10 40 40 40 40
2: 40 40 10 40 40 40
3: 40 40 40 10 40 40
4: 40 40 40 40 10 40
5: 40 40 40 40 40 10
After:
node distances:
node 0 1 2 3 4 5
0: 10 40 80 80 80 80
1: 40 10 80 80 80 80
2: 80 80 10 80 80 80
3: 80 80 80 10 80 80
4: 80 80 80 80 10 80
5: 80 80 80 80 80 10
These are the same distances as on the host, mirroring the change made
to host firmware in skiboot commit f845a648b8cb ("numa/associativity:
Add a new level of NUMA for GPU's").
Signed-off-by: Reza Arbab <arbab@linux.ibm.com>
Message-Id: <20200716225655.24289-1-arbab@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some recent error handling cleanups unveiled issues with our support of
PCI bridges:
1) QEMU aborts when using non-standard PCI bridge types,
unveiled by commit 7ef1553dac "spapr_pci: Drop some dead error handling"
$ qemu-system-ppc64 -M pseries -device pcie-pci-bridge
Unexpected error in object_property_find() at qom/object.c:1240:
qemu-system-ppc64: -device pcie-pci-bridge: Property '.chassis_nr' not found
Aborted (core dumped)
This happens because we assume all PCI bridge types to have a "chassis_nr"
property. This property only exists with the standard PCI bridge type
"pci-bridge" actually. We could possibly revert 7ef1553dac but it seems
much simpler to check the presence of "chassis_nr" earlier.
2) QEMU abort if same "chassis_nr" value is used several times,
unveiled by commit d2623129a7 "qom: Drop parameter @errp of
object_property_add() & friends"
$ qemu-system-ppc64 -M pseries -device pci-bridge,chassis_nr=1 \
-device pci-bridge,chassis_nr=1
Unexpected error in object_property_try_add() at qom/object.c:1167:
qemu-system-ppc64: -device pci-bridge,chassis_nr=1: attempt to add duplicate property '40000100' to object (type 'container')
Aborted (core dumped)
This happens because we assume that "chassis_nr" values are unique, but
nobody enforces that and we end up generating duplicate DRC ids. The PCI
code doesn't really care for duplicate "chassis_nr" properties since it
is only used to initialize the "Chassis Number Register" of the bridge,
with no functional impact on QEMU. So, even if passing the same value
several times might look weird, it never broke anything before, so
I guess we don't necessarily want to enforce strict checking in the PCI
code now.
Workaround both issues in the PAPR code: check that the bridge has a
unique and non null "chassis_nr" when plugging it into its parent bus.
Fixes: 05929a6c5d ("spapr: Don't use bus number for building DRC ids")
Fixes: 7ef1553dac ("spapr_pci: Drop some dead error handling")
Fixes: d2623129a7 ("qom: Drop parameter @errp of object_property_add() & friends")
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159431476748.407044.16711294833569014964.stgit@bahia.lan>
[dwg: Move check slightly to a better place]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU aborts with -device pnv-psi-POWER8:
$ qemu-system-ppc64 -device pnv-psi-POWER8
qemu-system-ppc64: hw/intc/xics.c:605: ics_realize: Assertion
`ics->xics' failed.
Aborted (core dumped)
The Processor Service Interface Controller is an internal device.
It should only be instantiated by the chip, which takes care of
configuring the link required by the ICS object in the case of
POWER8. It doesn't make sense for a user to specify it on the
command line.
Note that the PSI model for POWER8 was added 3 yrs ago but the
devices weren't available on the command line because of a bug
that was fixed by recent commit 2f35254aa0 ("pnv/psi: Correct
the pnv-psi* devices not to be sysbus devices").
Fixes: 54f59d786c ("ppc/pnv: Add cut down PSI bridge model and hookup external interrupt")
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159413975752.169116.5808968580649255382.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SET_SENSOR_READING is a complex IPMI command (see IPMI spec 35.17)
which enables the host software to set the reading value and the event
status of sensors supporting it.
Below is a proposal for all the operations (reading, assert, deassert,
event data) with the following limitations :
- No event are generated for threshold-based sensors.
- The case in which the BMC needs to generate its own events is not
supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20191118092429.16149-1-clg@kaod.org>
[Moved the break statement for case SENSOR_GEN_EVENT_DATA above the
closing brace to keep the indention consistent.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We use "create_simple" names for functions that allocate, initialize,
configure and realize device objects: pci_create_simple(),
isa_create_simple(), usb_create_simple(). For consistency, rename
i2c_create_slave() as i2c_slave_create_simple(). Since we have
to update all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-5-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The other i2c functions are called i2c_slave_FOO(). Rename as
i2c_slave_realize_and_unref() to be consistent.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-4-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We use "new" names for functions that allocate and initialize
device objects: pci_new(), isa_new(), usb_new().
Let's call this one i2c_slave_new(). Since we have to update
all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-3-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
All the callers of aspeed_i2c_get_bus() have a AspeedI2CState and
cast it to a DeviceState with DEVICE(), then aspeed_i2c_get_bus()
cast the DeviceState to an AspeedI2CState with ASPEED_I2C()...
Simplify aspeed_i2c_get_bus() callers by using AspeedI2CState
argument.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-2-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The System Management Bus is more or less a derivative of the I2C
bus, thus the Kconfig entry depends of I2C.
Not all boards providing an I2C bus support SMBus.
Use two different Kconfig entries to be able to select I2C without
selecting SMBus.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-6-philmd@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAl8PVgUACgkQda1lgCoL
QhHkeQgA2QkM4jJQ5QHG0rIin8PpbH/CZ3gn9gMwcrDLYxzrxguWaWLicvwF1VmN
hcqfHvyF5fs36v3ebCD9Gopc1NZyPce1iqaVwE/r1yTyFeBZyIMJ54IRhWyvqTbp
ndzq9jwZ4c+mIm4OueGHISP1EVJnfw6nq56zbJlZXVP9LrV+CTsr49ScaNwVXXxf
TeqLwWHwweJhqjSDRY4Tiqd+kLcEc/sl/2tRB3QE9lzM8ziCGdKg9oJMrimS/xdA
9+t5geDj3W3AF+e+fJ17InrEVcr+zU6XJYmKGMJ2yZvzIPof69UShVbd6XTO7Xpz
bKN8DEcfEaRwMFjuYpFCllTeXGsD4g==
=D8HF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2020-07-15-1' into staging
Merge tpm 2020/07/15 v1
# gpg: Signature made Wed 15 Jul 2020 20:16:21 BST
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* remotes/stefanberger/tags/pull-tpm-2020-07-15-1:
tests: tpm: Skip over pcrUpdateCounter byte in result comparison
tpm: tpm_spapr: Exit on TPM backend failures
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix the contition to figure whenever we need to wait for more data or
not. Simply check the mode, if we are not in DATAIN state any more we
are done already and don't need to go ASYNC.
Fixes: 7ad3d51ebb ("usb: add short-packet handling to usb-storage driver")
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Tested-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20200713062712.1476-1-kraxel@redhat.com
Calling ramfb_display_update() might replace the DisplaySurface with the
boot display, which in turn will free the currently active
DisplaySurface.
So clear our DisplaySurface pinter (dpy->region.surface pointer) to (a)
avoid use-after-free and (b) force replacing the boot display with the
real display when switching back.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-id: 20200713124520.23266-1-kraxel@redhat.com
Exit on TPM backend failures in the same way as the TPM CRB and TIS device
models do. With this change we now get an error report when the backend
did not start up properly:
error: internal error: qemu unexpectedly closed the monitor:
2020-07-07T12:49:28.333928Z qemu-system-ppc64: tpm-emulator: \
TPM result for CMD_INIT: 0x101 operation failed
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20200707201625.4177419-2-stefanb@linux.vnet.ibm.com
The test of the write of the dblac register was testing the old value
instead of the new value. This would accept the write of an invalid value
but subsequently refuse any following valid writes.
Signed-off-by: erik-smit <erik.lucas.smit@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Added fix for checksum offload for IPv6 if a backend doesn't
have a virtual header.
This patch is a part of IPv6 fragmentation.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
If you have a networking device and its virtio failover device, and
you remove them in this order:
- virtio device
- the real device
You get qemu crash.
See bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1820120
Bug exist on qemu 4.2 and 5.0.
But in 5.0 don't shows because commit
77b06bba62
somehow papers over it.
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
By using invalidated address, guest can do out-of-bounds accesses.
These patches fix the issue by only allowing SD card image sizes
power of 2, and not switching to SEND_DATA state when the address
is invalid (out of range).
This issue was found using QEMU fuzzing mode (using --enable-fuzzing,
see docs/devel/fuzzing.txt) and reported by Alexander Bulekov.
Reproducer:
https://bugs.launchpad.net/qemu/+bug/1880822/comments/1
CI jobs results:
. https://cirrus-ci.com/build/5157142548185088
. https://gitlab.com/philmd/qemu/-/pipelines/166381731
. https://travis-ci.org/github/philmd/qemu/builds/707956535
-----BEGIN PGP SIGNATURE-----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=VZsF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/sdcard-CVE-2020-13253-pull-request' into staging
Fix CVE-2020-13253
By using invalidated address, guest can do out-of-bounds accesses.
These patches fix the issue by only allowing SD card image sizes
power of 2, and not switching to SEND_DATA state when the address
is invalid (out of range).
This issue was found using QEMU fuzzing mode (using --enable-fuzzing,
see docs/devel/fuzzing.txt) and reported by Alexander Bulekov.
Reproducer:
https://bugs.launchpad.net/qemu/+bug/1880822/comments/1
CI jobs results:
. https://cirrus-ci.com/build/5157142548185088
. https://gitlab.com/philmd/qemu/-/pipelines/166381731
. https://travis-ci.org/github/philmd/qemu/builds/707956535
# gpg: Signature made Tue 14 Jul 2020 14:54:44 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/sdcard-CVE-2020-13253-pull-request:
hw/sd/sdcard: Do not switch to ReceivingData if address is invalid
hw/sd/sdcard: Update coding style to make checkpatch.pl happy
hw/sd/sdcard: Do not allow invalid SD card sizes
hw/sd/sdcard: Simplify realize() a bit
hw/sd/sdcard: Restrict Class 6 commands to SCSD cards
tests/acceptance/boot_linux: Expand SD card image to power of 2
tests/acceptance/boot_linux: Tag tests using a SD card with 'device:sd'
docs/orangepi: Add instructions for resizing SD image to power of two
MAINTAINERS: Cc qemu-block mailing list
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only move the state machine to ReceivingData if there is no
pending error. This avoids later OOB access while processing
commands queued.
"SD Specifications Part 1 Physical Layer Simplified Spec. v3.01"
4.3.3 Data Read
Read command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
4.3.4 Data Write
Write command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
WP_VIOLATION errors are not modified: the error bit is set, we
stay in receive-data state, wait for a stop command. All further
data transfer is ignored. See the check on sd->card_status at the
beginning of sd_read_data() and sd_write_data().
Fixes: CVE-2020-13253
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Buglink: https://bugs.launchpad.net/qemu/+bug/1880822
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-6-f4bug@amsat.org>
To make the next commit easier to review, clean this code first.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200630133912.9428-3-f4bug@amsat.org>
QEMU allows to create SD card with unrealistic sizes. This could
work, but some guests (at least Linux) consider sizes that are not
a power of 2 as a firmware bug and fix the card size to the next
power of 2.
While the possibility to use small SD card images has been seen as
a feature, it became a bug with CVE-2020-13253, where the guest is
able to do OOB read/write accesses past the image size end.
In a pair of commits we will fix CVE-2020-13253 as:
Read command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
Write command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
WP_VIOLATION errors are not modified: the error bit is set, we
stay in receive-data state, wait for a stop command. All further
data transfer is ignored. See the check on sd->card_status at the
beginning of sd_read_data() and sd_write_data().
While this is the correct behavior, in case QEMU create smaller SD
cards, guests still try to access past the image size end, and QEMU
considers this is an invalid address, thus "all further data transfer
is ignored". This is wrong and make the guest looping until
eventually timeouts.
Fix by not allowing invalid SD card sizes (suggesting the expected
size as a hint):
$ qemu-system-arm -M orangepi-pc -drive file=rootfs.ext2,if=sd,format=raw
qemu-system-arm: Invalid SD card size: 60 MiB
SD card size has to be a power of 2, e.g. 64 MiB.
You can resize disk images with 'qemu-img resize <imagefile> <new-size>'
(note that this will lose data if you make the image smaller than it currently is).
Cc: qemu-stable@nongnu.org
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200713183209.26308-8-f4bug@amsat.org>
We don't need to check if sd->blk is set twice.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-18-f4bug@amsat.org>
Only SCSD cards support Class 6 (Block Oriented Write Protection)
commands.
"SD Specifications Part 1 Physical Layer Simplified Spec. v3.01"
4.3.14 Command Functional Difference in Card Capacity Types
* Write Protected Group
SDHC and SDXC do not support write-protected groups. Issuing
CMD28, CMD29 and CMD30 generates the ILLEGAL_COMMAND error.
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-7-f4bug@amsat.org>
Conver the Ibex UART to use the recently added qdev-clock functions.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: b0136fad870a29049959ec161c1217b967d7e19d.1594332223.git.alistair.francis@wdc.com
Message-Id: <b0136fad870a29049959ec161c1217b967d7e19d.1594332223.git.alistair.francis@wdc.com>
At present the size of Mask ROM for sifive_u / spike / virt machines
is set to 0x11000, which ends at an unusual address. This changes the
size to 0xf000 so that it ends at 0x10000.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1594289144-24723-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Even though the start address in ROM code is declared as a 64 bit address
for RV64, it can't be used as upper bits are set to zero in ROM code.
Update the ROM code correctly to reflect the 64bit value.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-5-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
OpenSBI is the default firmware in Qemu and has various firmware loading
options. Currently, qemu loader uses fw_jump which has a compile time
pre-defined address where fdt & kernel image must reside. This puts a
constraint on image size of the Linux kernel depending on the fdt location
and available memory. However, fw_dynamic allows the loader to specify
the next stage location (i.e. Linux kernel/U-Boot) in memory and other
configurable boot options available in OpenSBI.
Add support for OpenSBI dynamic firmware loading support. This doesn't
break existing setup and fw_jump will continue to work as it is. Any
other firmware will continue to work without any issues as long as it
doesn't expect anything specific from loader in "a2" register.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-4-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, the fdt is copied to the ROM after the reset vector. The firmware
has to copy it to DRAM. Instead of this, directly copy the device tree to a
pre-computed dram address. The device tree load address should be as far as
possible from kernel and initrd images. That's why it is kept at the end of
the DRAM or 4GB whichever is lesser.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-3-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, all riscv machines except sifive_u have identical reset vector
code implementations with memory addresses being different for all machines.
They can be easily combined into a single function in common code.
Move it to common function and let all the machines use the common function.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-2-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Adjust the PCIe memory maps to follow the order.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1593746511-19517-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since added in commit 2bea128c3d, each SDHCI is wired with a SD
card, using empty card when no block drive provided. This is not
the desired behavior. The SDHCI exposes a SD bus to plug cards
on, if no card available, it is fine to have an unplugged bus.
Avoid creating unnecessary SD card device when no block drive
provided.
Fixes: 2bea128c3d ("hw/sd/aspeed_sdhci: New device")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200705173402.15620-1-f4bug@amsat.org
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace the free-floating set of IRQs and palmte_onoff_gpios()
function with a simple QOM device that encapsulates this
behaviour.
This fixes Coverity issue CID 1421944, which points out that
the memory returned by qemu_allocate_irqs() is leaked.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628214230.2592-3-peter.maydell@linaro.org
Remove hard-tabs from palm.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628214230.2592-2-peter.maydell@linaro.org
Currently we have a free-floating set of IRQs and a function
tosa_out_switch() which handle the GPIO lines on the tosa board which
connect to LEDs, and another free-floating IRQ and tosa_reset()
function to handle the GPIO line that resets the system. Encapsulate
this behaviour in a simple QOM device.
This commit fixes Coverity issue CID 1421929 (which pointed out that
the 'outsignals' in tosa_gpio_setup() were leaked), because it
removes the use of the qemu_allocate_irqs() API from this code
entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628203748.14250-3-peter.maydell@linaro.org
Remove the hardcoded tabs from hw/arm/tosa.c. There aren't
many, but since they're all in constant #defines they're not
going to go away with our usual "only when we touch a function"
policy on reformatting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628203748.14250-2-peter.maydell@linaro.org
Only when guest code is unmasking interrupts, terminate the excution
of translated code and exit to the main CPU loop to handle previous
pended interrupts because of the interrupts mask by guest code.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Message-id: 20200710233433.19729-4-wentong.wu@intel.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Regularize our handling of <sys/signal.h>: currently we include it in
osdep.h, but only for OpenBSD, and we include it without an ifdef
guard in a couple of C files. This causes problems for Haiku, which
doesn't have that header.
Instead, check in configure whether sys/signal.h exists, and if it
does then always include it from osdep.h.
Signed-off-by: David Carlier <devnexen@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200703145614.16684-5-peter.maydell@linaro.org
[PMM: Expanded commit message; rename to HAVE_SYS_SIGNAL_H]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coverity points out (CID 1430180) that the new case is missing
break or a /* fallthrough */ comment. Break is the right thing to
do as in that case, tail is not used.
Fixes 1733eebb9e ("virtio-iommu: Implement RESV_MEM probe request")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200708160147.18426-1-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
