If the user set disable smm by '-machine smm=off', we
should not register smram_listener so that we can
avoid waster memory in kvm since the added sencond
address space.
Meanwhile we should assign value of the global kvm_state
before invoking the kvm_arch_init(), because
pc_machine_is_smm_enabled() may use it by kvm_has_mm().
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Message-Id: <1496316915-121196-1-git-send-email-arei.gonglei@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It'll be nice to know which virq belongs to which device/vector when
adding msi routes, so adding two more parameters for the add trace.
Meanwhile, releasing virq has no tracing before. Add one for it.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1494309644-18743-2-git-send-email-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As a rule, CPU internal state should never be updated when
!cpu->kvm_vcpu_dirty (or the HAX equivalent). If that is done, then
subsequent calls to cpu_synchronize_state() - usually safe and idempotent -
will clobber state.
However, we routinely do this during a loadvm or incoming migration.
Usually this is called shortly after a reset, which will clear all the cpu
dirty flags with cpu_synchronize_all_post_reset(). Nothing is expected
to set the dirty flags again before the cpu state is loaded from the
incoming stream.
This means that it isn't safe to call cpu_synchronize_state() from a
post_load handler, which is non-obvious and potentially inconvenient.
We could cpu_synchronize_all_state() before the loadvm, but that would be
overkill since a) we expect the state to already be synchronized from the
reset and b) we expect to completely rewrite the state with a call to
cpu_synchronize_all_post_init() at the end of qemu_loadvm_state().
To clear this up, this patch introduces cpu_synchronize_pre_loadvm() and
associated helpers, which simply marks the cpu state as dirty without
actually changing anything. i.e. it says we want to discard any existing
KVM (or HAX) state and replace it with what we're going to load.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dave Gilbert <dgilbert@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Time to wire up all the call sites that request a shutdown or
reset to use the enum added in the previous patch.
It would have been less churn to keep the common case with no
arguments as meaning guest-triggered, and only modified the
host-triggered code paths, via a wrapper function, but then we'd
still have to audit that I didn't miss any host-triggered spots;
changing the signature forces us to double-check that I correctly
categorized all callers.
Since command line options can change whether a guest reset request
causes an actual reset vs. a shutdown, it's easy to also add the
information to reset requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> [ppc parts]
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> [SPARC part]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x parts]
Message-Id: <20170515214114.15442-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This dependency is the wrong way, and we will need util/qemu-timer.h from
sysemu/cpus.h in the next patch.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The purpose of the KVM_SET_SIGNAL_MASK API is to let userspace "kick"
a VCPU out of KVM_RUN through a POSIX signal. A signal is attached
to a dummy signal handler; by blocking the signal outside KVM_RUN and
unblocking it inside, this possible race is closed:
VCPU thread service thread
--------------------------------------------------------------
check flag
set flag
raise signal
(signal handler does nothing)
KVM_RUN
However, one issue with KVM_SET_SIGNAL_MASK is that it has to take
tsk->sighand->siglock on every KVM_RUN. This lock is often on a
remote NUMA node, because it is on the node of a thread's creator.
Taking this lock can be very expensive if there are many userspace
exits (as is the case for SMP Windows VMs without Hyper-V reference
time counter).
KVM_CAP_IMMEDIATE_EXIT provides an alternative, where the flag is
placed directly in kvm_run so that KVM can see it:
VCPU thread service thread
--------------------------------------------------------------
raise signal
signal handler
set run->immediate_exit
KVM_RUN
check run->immediate_exit
The previous patches changed QEMU so that the only blocked signal is
SIG_IPI, so we can now stop using KVM_SET_SIGNAL_MASK and sigtimedwait
if KVM_CAP_IMMEDIATE_EXIT is available.
On a 14-VCPU guest, an "inl" operation goes down from 30k to 6k on
an unlocked (no BQL) MemoryRegion, or from 30k to 15k if the BQL
is involved.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_on_sigbus_vcpu asynchronously from the VCPU thread.
Information for the SIGBUS can be stored in thread-local variables
and processed later in kvm_cpu_exec.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Build it on kvm_arch_on_sigbus_vcpu instead. They do the same
for "action optional" SIGBUSes, and the main thread should never get
"action required" SIGBUSes because it blocks the signal.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
it's not very convenient to use the crash-information property interface,
so provide a CPU class callback to get the guest crash information, and pass
that information in the event
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Message-Id: <1487053524-18674-3-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Windows reports BSOD parameters through Hyper-V crash MSRs. This
information is very useful for initial crash analysis and thus
it would be nice to have a way to fetch it.
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Message-Id: <1487053524-18674-2-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce rules in the top level Makefile that are able to generate
trace.[ch] files in every subdirectory which has a trace-events file.
The top level directory is handled specially, so instead of creating
trace.h, it creates trace-root.h. This allows sub-directories to
include the top level trace-root.h file, without ambiguity wrt to
the trace.g file in the current sub-dir.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170125161417.31949-7-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This changes the *_run_on_cpu APIs (and helpers) to pass data in a
run_on_cpu_data type instead of a plain void *. This is because we
sometimes want to pass a target address (target_ulong) and this fails on
32 bit hosts emulating 64 bit guests.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20161027151030.20863-24-alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The changes to run_on_cpu and friends mean that all helpers are passed
the CPUState of vCPU they are running on. The conversion missed the
field in commit e0eeb4a21a which
introduced bugs.
Reported-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Tested-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20161010154625.14881-1-alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce global kvm_msi_use_devid flag plus associated
kvm_msi_devid_required() macro. Passes the device ID,
if needed, while building the MSI route entry. Device IDs are
required by the ARM GICv3 ITS (IRQ remapping function is based on
this information).
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1474616617-366-5-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CPUState is a fairly common pointer to pass to these helpers. This means
if you need other arguments for the async_run_on_cpu case you end up
having to do a g_malloc to stuff additional data into the routine. For
the current users this isn't a massive deal but for MTTCG this gets
cumbersome when the only other parameter is often an address.
This adds the typedef run_on_cpu_func for helper functions which has an
explicit CPUState * passed as the first parameter. All the users of
run_on_cpu and async_run_on_cpu have had their helpers updated to use
CPUState where available.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
[Sergey Fedorov:
- eliminate more CPUState in user data;
- remove unnecessary user data passing;
- fix target-s390x/kvm.c and target-s390x/misc_helper.c]
Signed-off-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc parts)
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> (s390 parts)
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <1470158864-17651-3-git-send-email-alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_setup_guest_memory only does "madvise to QEMU_MADV_DONTFORK" and
is only called by ram_block_add, which actually is duplicate code.
Bonus: add simple comment for kvm_has_sync_mmu to make life easier.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Message-Id: <1473662096-32598-1-git-send-email-caoj.fnst@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1470224274-31522-5-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reported from Alexey Kardashevskiy:
3f1fea0fb5 "kvm-irqchip: do explicit commit when update irq" produces
a crash on pseries guest running with VFIO on POWER8 machine as it does
not support KVM_CAP_IRQCHIP (KVM_CAP_IRQ_XICS is there instead). At the
result, KVMState::irq_routes is NULL when VFIO calls
kvm_irqchip_commit_routes.
This makes the routing update conditional.
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These will help us monitoring irqchip route activities more easily.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the past, we are doing gsi route commit for each irqchip route
update. This is not efficient if we are updating lots of routes in the
same time. This patch removes the committing phase in
kvm_irqchip_update_msi_route(). Instead, we do explicit commit after all
routes updated.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
One more IEC notifier is added to let msi routes know about the IEC
changes. When interrupt invalidation happens, all registered msi routes
will be updated for all PCI devices.
Since both vfio and vhost are possible gsi route consumers, this patch
will go one step further to keep them safe in split irqchip mode and
when irqfd is enabled.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
[move trace-events lines into target-i386/trace-events]
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Adding two hooks to be notified when adding/removing msi routes. There
are two kinds of MSI routes:
- in kvm_irqchip_add_irq_route(): before assigning IRQFD. Used by
vhost, vfio, etc.
- in kvm_irqchip_send_msi(): when sending direct MSI message, if
direct MSI not allowed, we will first create one MSI route entry
in the kernel, then trigger it.
This patch only hooks the first one (irqfd case). We do not need to
take care for the 2nd one, since it's only used by QEMU userspace
(kvm-apic) and the messages will always do in-time translation when
triggered. While we need to note them down for the 1st one, so that we
can notify the kernel when cache invalidation happens.
Also, we do not hook IOAPIC msi routes (we have explicit notifier for
IOAPIC to keep its cache updated). We only need to care about irqfd
users.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Changing the original MSIMessage parameter in kvm_irqchip_add_msi_route
into the vector number. Vector index provides more information than the
MSIMessage, we can retrieve the MSIMessage using the vector easily. This
will avoid fetching MSIMessage every time before adding MSI routes.
Meanwhile, the vector info will be used in the coming patches to further
enable gsi route update notifications.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As stated in linux/Documentation/virtual/kvm/api.txt:
The maximum possible value for max_vcpu_id can be retrieved using the
KVM_CAP_MAX_VCPU_ID of the KVM_CHECK_EXTENSION ioctl() at run-time.
If the KVM_CAP_MAX_VCPU_ID does not exist, you should assume that
max_vcpu_id is the same as the value returned from KVM_CAP_MAX_VCPUS.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Message-Id: <146424974323.5666.5471538288045048119.stgit@bahia.huguette.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu/osdep.h checks whether MAP_ANONYMOUS is defined, but this check
is bogus without a previous inclusion of sys/mman.h. Include it in
sysemu/os-posix.h and remove it from everywhere else.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce kvm_get_max_memslots() API that can be used to obtain the
maximum number of memslots supported by KVM.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In order to deal well with the kvm vcpus (which can not be removed without any
protection), we do not close KVM vcpu fd, just record and mark it as stopped
into a list, so that we can reuse it for the appending cpu hot-add request if
possible. It is also the approach that kvm guys suggested:
https://www.mail-archive.com/kvm@vger.kernel.org/msg102839.html
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
[- Explicit CPU_REMOVE() from qemu_kvm/tcg_destroy_vcpu()
isn't needed as it is done from cpu_exec_exit()
- Use iothread mutex instead of global mutex during
destroy
- Don't cleanup vCPU object from vCPU thread context
but leave it to the callers (device_add/device_del)]
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM API restricts vcpu ids to be < KVM_CAP_MAX_VCPUS. On PowerPC
targets, depending on the number of threads per core in the host and
in the guest, some topologies do generate higher vcpu ids actually.
When this happens, QEMU bails out with the following error:
kvm_init_vcpu failed: Invalid argument
The KVM_CREATE_VCPU ioctl has several EINVAL return paths, so it is
not possible to fully disambiguate.
This patch adds a check in the code that computes vcpu ids, so that
we can detect the error earlier, and print a friendlier message instead
of calling KVM_CREATE_VCPU with an obviously bogus vcpu id.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This can be used when probing whether KVM support specific device. Here,
a raw vmfd is used.
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: Sergey Fedorov <serge.fdrv@gmail.com>
Message-id: 1458788142-17509-4-git-send-email-peterx@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By using utilities in bitops and bitmap, this patch tries to make it more
friendly to audience. No functional change.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Message-Id: <1457229445-25954-1-git-send-email-richard.weiyang@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All references to mr->ram_addr are replaced by
memory_region_get_ram_addr(mr) (except for a few assertions that are
replaced with mr->ram_block).
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <1456813104-25902-5-git-send-email-famz@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-Id: <1454355464-14999-1-git-send-email-drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-16-git-send-email-peter.maydell@linaro.org
The arguments of error_report() should yield a short error string
without newlines.
A few places try to print additional help after the error message by
embedding newlines in the error string. That's nice, but let's do it
the right way. Commit 474c213 cleaned up some, but they keep coming
back. Offenders tracked down with the Coccinelle semantic patch from
commit 312fd5f.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This patch adds support for split IRQ chip mode. When
KVM_CAP_SPLIT_IRQCHIP is enabled:
1.) The PIC, PIT, and IOAPIC are implemented in userspace while
the LAPIC is implemented by KVM.
2.) The software IOAPIC delivers interrupts to the KVM LAPIC via
kvm_set_irq. Interrupt delivery is configured via the MSI routing
table, for which routes are reserved in target-i386/kvm.c then
configured in hw/intc/ioapic.c
3.) KVM delivers IOAPIC EOIs via a new exit KVM_EXIT_IOAPIC_EOI,
which is handled in target-i386/kvm.c and relayed to the software
IOAPIC via ioapic_eoi_broadcast.
Signed-off-by: Matt Gingell <gingell@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ioeventfd mechanism is used by vhost, dataplane, and virtio-pci to
turn guest MMIO/PIO writes into eventfd file descriptor events. This
allows arbitrary threads to be notified when the guest writes to a
specific MMIO/PIO address.
qtest and TCG do not support ioeventfd because memory writes are not
checked against registered ioeventfds in QEMU. This patch implements
this in memory_region_dispatch_write() so qtest can use ioeventfd.
Also this patch fixes vhost aborting on some misconfigured old kernels
like 3.18.0 on ARM. It is possible to explicitly enable CONFIG_EVENTFD
in expert settings, while MMIO binding support in KVM will still be
missing.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-Id: <006e01d12377$0b9c2d40$22d487c0$@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Just noticed this while grepping TARGET_PAGE_SIZE for an unrelated
reason. I didn't use qemu_real_host_page_size as kvm_set_phys_mem()
does, because we'd need to make sure page_size_init() has run first.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-Id: <1447115022-4142-1-git-send-email-drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
The HOST_PAGE_ALIGN macros don't work until the page size variables
have been set up; later in postcopy I use those macros in the RAM
code, and it can be triggered using -object.
Fix this by initialising page_size_init() earlier - it's currently
initialised inside the accelerators, move it up into vl.c.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This reverts commit de9d61e83d.
Now 'cpu_clean_all_dirty' is useless, we can revert the related code.
Conflicts:
include/sysemu/kvm.h
Signed-off-by: Liang Li <liang.z.li@intel.com>
Message-Id: <1446695464-27116-3-git-send-email-liang.z.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions for checking xcrs, xsave and pit_state2 are
only used on x86, so they should reside in target-i386/kvm.c.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1444933820-6968-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In-kernel ITS emulation on ARM64 will require to supply requester IDs.
These IDs can now be retrieved from the device pointer using new
pci_requester_id() function.
This patch adds pci_dev pointer to KVM GSI routing functions and makes
callers passing it.
x86 architecture does not use requester IDs, but hw/i386/kvm/pci-assign.c
also made passing PCI device pointer instead of NULL for consistency with
the rest of the code.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-Id: <ce081423ba2394a4efc30f30708fca07656bc500.1444916432.git.p.fedin@samsung.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This capability is useful to determine whether we can use KVM ITS
emulation on ARM
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-Id: <ff4ccb09b837d37defd639b885526949a25276de.1444916432.git.p.fedin@samsung.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As the comment in kvm_set_phys_mem() says, KVM works in page size chunks.
However it uses hardcoded TARGET_PAGE_SIZE which is 4K on most platforms
while actual host may use different page size, for example, PPC64 hosts
use 64K system pages.
This replaces static TARGET_PAGE_SIZE with run-time calculated
qemu_real_host_page_size.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <1444102257-17405-1-git-send-email-aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some functions previously used only by vGICv2 are useful also for vGICv3
implementation. Untie them from GICState and make accessible from within
other modules:
- kvm_arm_gic_set_irq()
- kvm_gic_supports_attr() - moved to common code and renamed to
kvm_device_check_attr()
- kvm_gic_access() - turned into GIC-independent kvm_device_access().
Data pointer changed to void * because some GICv3 registers are
64-bit wide
Some of these changes are not used right now, but they will be helpful for
implementing live migration.
Actually kvm_dist_get() and kvm_dist_put() could also be made reusable, but
they would require two extra parameters (s->dev_fd and s->num_cpu) as well as
lots of typecasts of 's' to DeviceState * and back to GICState *. This makes
the code very ugly so i decided to stop at this point. I tried also an
approach with making a base class for all possible GICs, but it would contain
only three variables (dev_fd, cpu_num and irq_num), and accessing them through
the rest of the code would be again tedious (either ugly casts or qemu-style
separate object pointer). So i disliked it too.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2ef56d1dd64ffb75ed02a10dcdaf605e5b8ff4f8.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
KVM kernel can send guest crash events into userspace.
Appropriate guest crash handler is called when kernel guest
crash event received. Guest crash event recognized by a
KVM_SYSTEM_EVENT_CRASH type of system event.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1435924905-8926-11-git-send-email-den@openvz.org>
[Rebase: add lock/unlock iothread around qemu_system_guest_panicked - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
