Add smbios support for loongarch virt machine, and put them into fw_cfg
table so that bios can parse them quickly. The weblink of smbios spec:
https://www.dmtf.org/dsp/DSP0134, the version is 3.6.0.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220712083206.4187715-5-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add uefi bios loading support, now only uefi bios is porting to
loongarch virt machine.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220712083206.4187715-3-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add fw_cfg table for loongarch virt machine, including memmap table.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220712083206.4187715-2-yangxiaojuan@loongson.cn>
[rth: Replace fprintf with assert; drop unused return value;
initialize reserved slot to zero.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This legacy function is only used during the initialisation of the MIPS magnum
machine, so inline its functionality directly into mips_jazz_init() and then
remove it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-41-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now that the legacy ps2_mouse_init() function is no longer used, it can be completely
removed along with its associated trace-event.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-40-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 mouse device within KBDState using
object_initialize_child() in i8042_initfn() and i8042_mmio_init() and realize
it in i8042_realizefn() and i8042_mmio_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-39-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now that the legacy ps2_kbd_init() function is no longer used, it can be completely
removed along with its associated trace-event.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-38-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 keyboard device within KBDState using
object_initialize_child() in i8042_initfn() and i8042_mmio_init() and realize
it in i8042_realizefn() and i8042_mmio_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-37-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 mouse device within LASIPS2MousePort using
object_initialize_child() in lasips2_mouse_port_init() and realize it in
lasips2_mouse_port_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-34-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 keyboard device within LASIPS2KbdPort using
object_initialize_child() in lasips2_kbd_port_init() and realize it in
lasips2_kbd_port_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-33-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This makes it clearer that the pointer is a reference to the LASIPS2 container
device rather than an implied part of the QOM hierarchy.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-30-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now we can implement port-based IRQs by wiring the PS2 device IRQs to the
LASI2Port named input gpios rather than directly to the LASIPS2 device, and
generate the LASIPS2 output IRQ from the int_status bitmap representing the
individual port IRQs instead of the birq boolean.
This enables us to remove the separate PS2 keyboard and PS2 mouse named input
gpios from the LASIPS2 device and simplify the register implementation to
drive the port IRQ using qemu_set_irq() rather than accessing the LASIPS2
device IRQs directly. As a consequence the IRQ level logic in lasips2_set_irq()
can also be simplified accordingly.
For now this patch ignores adding the int_status bitmap and simply drops the
birq boolean from the vmstate_lasips2 VMStateDescription. This is because the
migration stream is already missing some required LASIPS2 fields, and as this
series already introduces a migration break for the lasips2 device it is
easiest to fix this in a follow-up patch.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220712215251.7944-29-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The LASIPS2 device named input gpio is soon to be connected to the port output
IRQs. Add a new int_status field to LASIPS2State which is a bitmap representing
the port input IRQ status which will be enabled in the next patch.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220712215251.7944-28-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The named input gpio is to be connected to the IRQ output of the downstream
PS2 device and used to drive the port IRQ. Initialise the named input gpio
in lasips2_port_init() and add new lasips2_port_class_init() and
lasips2_port_realize() functions to connect the PS2 device output gpio to
the new named input gpio.
Note that the reference to lasips2_port_realize() is stored in
LASIPS2PortDeviceClass but not yet used.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-27-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will soon be used to store the reference to the LASIPS2_PORT parent device
for LASIPS2_KBD_PORT and LASIPS2_MOUSE_PORT.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-26-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Introduce a new lasips2_port_init() QOM init function for the LASIPS2_PORT type
and use it to initialise a new gpio for use as a port IRQ. Add a new qemu_irq
representing the gpio as a new irq field within LASIPS2Port.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-25-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The existing boolean irq field in LASIPS2Port will soon be replaced by a proper
qemu_irq, so rename the field to birq to allow the upcoming qemu_irq to use the
irq name.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-24-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move the initialisation of the mouse port from lasips2_init() to
a new lasips2_mouse_port_init() function which will be invoked using
object_initialize_child() during the LASIPS2 device init.
Update LASIPS2State so that it now holds the new LASIPS2MousePort child object and
ensure that it is realised in lasips2_realize().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-21-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move the initialisation of the keyboard port from lasips2_init() to
a new lasips2_kbd_port_init() function which will be invoked using
object_initialize_child() during the LASIPS2 device init.
Update LASIPS2State so that it now holds the new LASIPS2KbdPort child object and
ensure that it is realised in lasips2_realize().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-20-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will be soon be used to hold the underlying PS2_MOUSE_DEVICE object.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-19-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will be soon be used to hold the underlying PS2_KBD_DEVICE object.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-18-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This becomes an abstract QOM type which will be a parent type for separate
keyboard and mouse port types.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-17-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This allows the compiler to enforce that the PS2 device pointer is always of
type PS2State. Update the name of the pointer from dev to ps2dev to emphasise
this type change.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-16-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is only one user of the legacy lasips2_initfn() function which is in
machine_hppa_init(), so inline its functionality into machine_hppa_init() and
then remove it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-15-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The base property was only needed for use by vmstate_register() in order to
preserve migration compatibility. Now that the lasips2 migration state is
registered through the DeviceClass vmsd field, the base property and also
the lasips2_properties array can be removed completely as they are no longer
required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-14-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 mouse device within PL050MouseState using
object_initialize_child() in pl050_mouse_init() and realize it in
pl050_mouse_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-12-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 keyboard device within PL050KbdState using
object_initialize_child() in pl050_kbd_init() and realize it in
pl050_kbd_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-11-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will soon be used to store the reference to the PL050 parent device
for PL050_KBD_DEVICE and PL050_MOUSE_DEVICE.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-8-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will be soon be used to hold the underlying PS2_MOUSE_DEVICE object.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-6-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will be soon be used to hold the underlying PS2_KBD_DEVICE object.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-5-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This allows the compiler to enforce that the PS2 device pointer is always of
type PS2State. Update the name of the pointer from dev to ps2dev to emphasise
this type change.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-4-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This allows the QOM types in pl050.c to be used elsewhere by simply including
pl050.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is nothing in the specs on DMA engine interrupt lines: it should have
been in the "BCM2835 ARM Peripherals" datasheet but the appropriate
"ARM peripherals interrupt table" (p.113) is nearly empty.
All Raspberry Pi models 1-3 (based on bcm2835) have
Linux device tree (arch/arm/boot/dts/bcm2835-common.dtsi +25):
/* dma channel 11-14 share one irq */
This information is repeated in the driver code
(drivers/dma/bcm2835-dma.c +1344):
/*
* in case of channel >= 11
* use the 11th interrupt and that is shared
*/
In this patch channels 0--10 and 11--14 are handled separately.
Signed-off-by: Andrey Makarov <andrey.makarov@auriga.com>
Message-id: 20220716113210.349153-1-andrey.makarov@auriga.com
[PMM: fixed checkpatch nits]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
performance improvements by Jinhao
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* shadow doorbells
* ioeventfd
plus some misc fixes (Darren, Niklas).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEUigzqnXi3OaiR2bATeGvMW1PDekFAmLRKGwACgkQTeGvMW1P
Deki7Af9Hg0ltW9RyxzUtYB5hwaMpgrHHcViBoLK8mt7wa5hh5luFb1P3/+yltUG
LU/cws93mq3jDy30dKnVa5+xugDmuEy470OxjJPCivLEpV6qpONulp+iHFIKim4N
kPXX8K1R4XVTVvCFFpmub6GUCFZpXRVW9uPAAL96BzaSjEK7K+5H3boJ7HfT5YUY
Tx9LuPQUcIUHViF/4wNU0Sqx15PoOOjHqSnA3EjCDCscqPkbhaoEoyI5Pk+BMxzf
tElNh/ffP5x0BSaKOofdtW+iHaxlSgPJ6IA0W9dwXJyRCvoaa9near2iGXDa6PEA
bRpQpudzIkL3Swfgcm4D+N7NQbCSOg==
=Wg5B
-----END PGP SIGNATURE-----
Merge tag 'nvme-next-pull-request' of git://git.infradead.org/qemu-nvme into staging
hw/nvme updates
performance improvements by Jinhao
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* shadow doorbells
* ioeventfd
plus some misc fixes (Darren, Niklas).
# gpg: Signature made Fri 15 Jul 2022 09:42:20 BST
# gpg: using RSA key 522833AA75E2DCE6A24766C04DE1AF316D4F0DE9
# gpg: Good signature from "Klaus Jensen <its@irrelevant.dk>" [unknown]
# gpg: aka "Klaus Jensen <k.jensen@samsung.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DDCA 4D9C 9EF9 31CC 3468 4272 63D5 6FC5 E55D A838
# Subkey fingerprint: 5228 33AA 75E2 DCE6 A247 66C0 4DE1 AF31 6D4F 0DE9
* tag 'nvme-next-pull-request' of git://git.infradead.org/qemu-nvme:
hw/nvme: Use ioeventfd to handle doorbell updates
nvme: Fix misleading macro when mixed with ternary operator
hw/nvme: force nvme-ns param 'shared' to false if no nvme-subsys node
hw/nvme: fix example serial in documentation
hw/nvme: Add trace events for shadow doorbell buffer
hw/nvme: Implement shadow doorbell buffer support
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New ISL69259 device model
* New fby35 multi-SoC machine (AST1030 BIC + AST2600 BMC)
* Aspeed GPIO fixes
* Extension of m25p80 with write protect bits
* More avocado tests using the Aspeed SDK
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmLQJ/kACgkQUaNDx8/7
7KFO5BAAkqiSSQ9G3ihI51ET3+inihrw9wmN7FX5eMOxj8csLz1UbKOJ/YtjXvgt
whfY5/iugVveUW+/X1xZmHbydec24f/umSpqqCtkPkIwCgvN4gjQAriXTK4qqx7g
pCZoWxYeHsR19r985y//I+wFPB//Dd3Ac/1BgA4m0tdy/bK3MPLV2ocDe8d09Yfe
wDYAFby4q8raKzMkJMibP7/phIg4hyguNAYtkSUsJChnXjK8/2ymsjlx7Xz+N1Gp
Fynv9vaFiYOEvmDTPqbs7XMs3Qc+Sjz2RsxgaEdSI4pLk8H8hhgVueYE1ctWlpkI
7q/g5KjXZsq6eKxNYDqU+ysY+vjdLZmO1tEmolgR+k4C+ladUYSBaI1XiGJjCmpb
6vkM2ls1sgmb6C24e8vP64Jp/AgT6Qg7OW1Db3VcpBbQirf9SqtkXezgseOrsnXm
Ni1uQF9NwUiRUWTA/bK4y/pSYNItoQ4KkeoAWPsiEm0d4Pezk2X+EMjJcCTQw9Zx
BFtDxi/3rWB3imvhizynT93+rtNH7Z74kiI7iZGbZr6L2XhpEUlwoo+EOaeb4XAS
ZEuR+kBNUMR9k4YhyF0DlvN61SuD703SdXCROsUq3EzCgza24JM4bl2IMSyv9Wdj
DCL6yYEyf8FsJ9+KtK8A1uXc2yDcV4iGfEqOReTB5+k99ICzgEg=
=faie
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20220714' of https://github.com/legoater/qemu into staging
aspeed queue:
* New ISL69259 device model
* New fby35 multi-SoC machine (AST1030 BIC + AST2600 BMC)
* Aspeed GPIO fixes
* Extension of m25p80 with write protect bits
* More avocado tests using the Aspeed SDK
# gpg: Signature made Thu 14 Jul 2022 15:28:09 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20220714' of https://github.com/legoater/qemu:
aspeed: Add fby35-bmc slot GPIO's
hw/gpio/aspeed: Don't let guests modify input pins
qtest/aspeed_gpio: Add input pin modification test
hw: m25p80: add tests for BP and TB bit write protect
hw: m25p80: Add Block Protect and Top Bottom bits for write protect
test/avocado/machine_aspeed.py: Add SDK tests
docs: aspeed: Minor updates
docs: aspeed: Add fby35 multi-SoC machine section
aspeed: Add AST1030 (BIC) to fby35
aspeed: fby35: Add a bootrom for the BMC
aspeed: Add AST2600 (BMC) to fby35
aspeed: Add fby35 skeleton
aspeed: Make aspeed_board_init_flashes public
aspeed: Refactor UART init for multi-SoC machines
aspeed: Create SRAM name from first CPU index
hw/sensor: Add Renesas ISL69259 device model
hw/sensor: Add IC_DEVICE_ID to ISL voltage regulators
hw/i2c/pmbus: Add idle state to return 0xff's
aspeed: sbc: Allow per-machine settings
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using the Parfait source code analyser and issue was found in
hw/nvme/ctrl.c where the macros NVME_CAP_SET_CMBS and NVME_CAP_SET_PMRS
are called with a ternary operatore in the second parameter, resulting
in a potentially unexpected expansion of the form:
x ? a: b & FLAG_TEST
which will result in a different result to:
(x ? a: b) & FLAG_TEST.
The macros should wrap each of the parameters in brackets to ensure the
correct result on expansion.
Signed-off-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Implement Doorbel Buffer Config command (Section 5.7 in NVMe Spec 1.3)
and Shadow Doorbel buffer & EventIdx buffer handling logic (Section 7.13
in NVMe Spec 1.3). For queues created before the Doorbell Buffer Config
command, the nvme_dbbuf_config function tries to associate each existing
SQ and CQ with its Shadow Doorbel buffer and EventIdx buffer address.
Queues created after the Doorbell Buffer Config command will have the
doorbell buffers associated with them when they are initialized.
In nvme_process_sq and nvme_post_cqe, proactively check for Shadow
Doorbell buffer changes instead of wait for doorbell register changes.
This reduces the number of MMIOs.
In nvme_process_db(), update the shadow doorbell buffer value with
the doorbell register value if it is the admin queue. This is a hack
since hosts like Linux NVMe driver and SPDK do not use shadow
doorbell buffer for the admin queue. Copying the doorbell register
value to the shadow doorbell buffer allows us to support these hosts
as well as spec-compliant hosts that use shadow doorbell buffer for
the admin queue.
Signed-off-by: Jinhao Fan <fanjinhao21s@ict.ac.cn>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
[k.jensen: rebased]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
* pre-install data files in the build directory (Akihiko)
* SCSI fixes for Mac OS (Mark)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmLO3bQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNv5AgAgGe8hGOcqJSzmFgeUJ7UEaauap6E
fF4zau8Xux7R6pnvPe2FeJ70AlvstFAUoU++7G3linQ+eqnFD7E18KQkfp9qX7jY
xDFPJRf6JNhwDjxQ2Tp0ShOcm5HkDv4Z4cPlx0T+wfKTlUWCzNEkhVrjOhpDYnSe
OldsdFjY0sUjZ1R/QNiuQ65aWwOr9gJ07KfakJQMX2YCMun6SO3kB/GtmyecTV3C
uNAUIdqJLsEbR1ckdMVVmixhtzMPW2R7/vjJkxG8RXUAcDmDHkuKPhWKyZ9a7/hh
CV8iMQMup6mgT8ndb5DWv551Y+C/rA1bH9U1NkaeQ9RP83CE4a6fpSMiiQ==
=82zT
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* SCSI fuzzing fix (Mauro)
* pre-install data files in the build directory (Akihiko)
* SCSI fixes for Mac OS (Mark)
# gpg: Signature made Wed 13 Jul 2022 15:59:00 BST
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu:
pc-bios/s390-ccw: add -Wno-array-bounds
q800: add default vendor and product information for scsi-cd devices
q800: add default vendor and product information for scsi-hd devices
scsi-disk: allow MODE SELECT block descriptor to set the block size
scsi-disk: allow the MODE_PAGE_R_W_ERROR AWRE bit to be changeable for CDROM drives
q800: implement compat_props to enable quirk_mode_page_truncated for scsi-cd devices
scsi-disk: add SCSI_DISK_QUIRK_MODE_PAGE_TRUNCATED quirk for Macintosh
scsi-disk: add FORMAT UNIT command
q800: implement compat_props to enable quirk_mode_page_vendor_specific_apple for scsi devices
scsi-disk: add SCSI_DISK_QUIRK_MODE_PAGE_VENDOR_SPECIFIC_APPLE quirk for Macintosh
q800: implement compat_props to enable quirk_mode_sense_rom_use_dbd for scsi-cd devices
scsi-disk: add SCSI_DISK_QUIRK_MODE_SENSE_ROM_USE_DBD quirk for Macintosh
q800: implement compat_props to enable quirk_mode_page_apple_vendor for scsi-cd devices
scsi-disk: add MODE_PAGE_APPLE_VENDOR quirk for Macintosh
scsi-disk: add new quirks bitmap to SCSIDiskState
meson: Prefix each element of firmware path
module: Use bundle mechanism
datadir: Use bundle mechanism
cutils: Introduce bundle mechanism
scsi/lsi53c895a: really fix use-after-free in lsi_do_msgout (CVE-2022-0216)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This change moves the code that connects the SoC UART's to serial_hd's
to the machine.
It makes each UART a proper child member of the SoC, and then allows the
machine to selectively initialize the chardev for each UART with a
serial_hd.
This should preserve backwards compatibility, but also allow multi-SoC
boards to completely change the wiring of serial devices from the
command line to specific SoC UART's.
This also removes the uart-default property from the SoC, since the SoC
doesn't need to know what UART is the "default" on the machine anymore.
I tested this using the images and commands from the previous
refactoring, and another test image for the ast1030:
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/fuji.mtd
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/wedge100.mtd
wget https://github.com/peterdelevoryas/OpenBIC/releases/download/oby35-cl-2022.13.01/Y35BCL.elf
Fuji uses UART1:
qemu-system-arm -machine fuji-bmc \
-drive file=fuji.mtd,format=raw,if=mtd \
-nographic
ast2600-evb uses uart-default=UART5:
qemu-system-arm -machine ast2600-evb \
-drive file=fuji.mtd,format=raw,if=mtd \
-serial null -serial mon:stdio -display none
Wedge100 uses UART3:
qemu-system-arm -machine palmetto-bmc \
-drive file=wedge100.mtd,format=raw,if=mtd \
-serial null -serial null -serial null \
-serial mon:stdio -display none
AST1030 EVB uses UART5:
qemu-system-arm -machine ast1030-evb \
-kernel Y35BCL.elf -nographic
Fixes: 6827ff20b2 ("hw: aspeed: Init all UART's with serial devices")
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-4-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds a passthrough for PMBUS_IC_DEVICE_ID to allow Renesas
voltage regulators to return the integrated circuit device ID if they
would like to.
The behavior is very device specific, so it hasn't been added to the
general PMBUS model. Additionally, if the device ID hasn't been set,
then the voltage regulator will respond with the error byte value. The
guest error message will change slightly for IC_DEVICE_ID with this
commit.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-3-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-2-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In order to correctly report secure boot running firmware the values
of certain registers must be set.
We don't yet have documentation from ASPEED on what they mean. The
meaning is inferred from u-boot's use of them.
Introduce properties so the settings can be configured per-machine.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Tested-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20220628154740.1117349-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When A/UX configures the CDROM device it sends a truncated MODE SELECT request
for page 1 (MODE_PAGE_R_W_ERROR) which is only 6 bytes in length rather than
10. This seems to be due to bug in Apple's code which calculates the CDB message
length incorrectly.
The work at [1] suggests that this truncated request is accepted on real
hardware whereas in QEMU it generates an INVALID_PARAM_LEN sense code which
causes A/UX to get stuck in a loop retrying the command in an attempt to succeed.
Alter the mode page request length check so that truncated requests are allowed
if the SCSI_DISK_QUIRK_MODE_PAGE_TRUNCATED quirk is enabled, whilst also adding a
trace event to enable the condition to be detected.
[1] https://68kmla.org/bb/index.php?threads/scsi2sd-project-anyone-interested.29040/page-7#post-316444
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both MacOS and A/UX make use of vendor-specific MODE SELECT commands with PF=0
to identify SCSI devices:
- MacOS sends a MODE SELECT command with PF=0 for the MODE_PAGE_VENDOR_SPECIFIC
(0x0) mode page containing 2 bytes before initialising a disk
- A/UX (installed on disk) sends a MODE SELECT command with PF=0 during SCSI
bus enumeration, and gets stuck in an infinite loop if it fails
Add a new SCSI_DISK_QUIRK_MODE_PAGE_VENDOR_SPECIFIC_APPLE quirk to allow both
PF=0 MODE SELECT commands and implement a MODE_PAGE_VENDOR_SPECIFIC (0x0)
mode page which is compatible with MacOS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
During SCSI bus enumeration A/UX sends a MODE SENSE command to the CDROM with
the DBD bit unset and expects the response to include a block descriptor. As per
the latest SCSI documentation, QEMU currently force-disables the block
descriptor for CDROM devices but the A/UX driver expects the requested block
descriptor to be returned.
If the block descriptor is not returned in the response then A/UX becomes
confused, since the block descriptor returned in the MODE SENSE response is
used to generate a subsequent MODE SELECT command which is then invalid.
Add a new SCSI_DISK_QUIRK_MODE_SENSE_ROM_USE_DBD quirk to allow this behaviour
to be enabled as required. Note that an additional workaround is required for
the previous SCSI_DISK_QUIRK_MODE_PAGE_APPLE_VENDOR quirk which must never
return a block descriptor even though the DBD bit is left unset.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One of the mechanisms MacOS uses to identify CDROM drives compatible with MacOS
is to send a custom MODE SELECT command for page 0x30 to the drive. The
response to this is a hard-coded manufacturer string which must match in order
for the CDROM to be usable within MacOS.
Add an implementation of the MODE SELECT page 0x30 response guarded by a newly
defined SCSI_DISK_QUIRK_MODE_PAGE_APPLE_VENDOR quirk bit so that CDROM drives
attached to non-Apple machines function exactly as before.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Developers often run QEMU without installing. The bundle mechanism
allows to look up files which should be present in installation even in
such a situation.
It is a general mechanism and can find any files in the installation
tree. The build tree will have a new directory, qemu-bundle, to
represent what files the installation tree would have for reference by
the executables.
Note that it abandons compatibility with Windows older than 8. The
extended support for the prior version, 7 ended more than 2 years ago,
and it is unlikely that someone would like to run the latest QEMU on
such an old system.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220624145039.49929-3-akihiko.odaki@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function is no longer used.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220628111701.677216-7-richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Keep generated_co_wrapper and coroutine_fn pairs together. This should
make it clear that each I/O function has these two versions.
Also move blk_co_{pread,pwrite}()'s implementations out of the header
file for consistency.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220705161527.1054072-18-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Also convert blk_truncate() into a generated_co_wrapper.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-17-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Also convert blk_ioctl() into a generated_co_wrapper.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-16-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-15-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-14-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-13-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Also convert blk_pwrite_compressed() into a generated_co_wrapper.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-12-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Swap 'buf' and 'bytes' around for consistency with other I/O functions.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-11-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Also convert it into a generated_co_wrapper.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-10-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Implement blk_preadv_part() using generated_co_wrapper.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-9-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Implement them using generated_co_wrapper.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-8-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
We need to add include/sysemu/block-backend-io.h to the inputs of the
block-gen.c target defined in block/meson.build.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-7-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
It does not mutate the buffer.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-6-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement them using generated_co_wrapper.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-5-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Swap 'buf' and 'bytes' around for consistency with
blk_co_{pread,pwrite}(), and in preparation to implement these functions
using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pread(blk, offset, buf, bytes, flags)
+ blk_pread(blk, offset, bytes, buf, flags)
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pwrite(blk, offset, buf, bytes, flags)
+ blk_pwrite(blk, offset, bytes, buf, flags)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-4-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement it using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes; @@
- blk_pread(blk, offset, buf, bytes)
+ blk_pread(blk, offset, buf, bytes, 0)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-3-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Also convert bdrv_pwrite_sync() to being implemented using
generated_co_wrapper.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220609152744.3891847-9-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
bdrv_{pread,pwrite}() now return -EIO instead of -EINVAL when 'bytes' is
negative, making them consistent with bdrv_{preadv,pwritev}() and
bdrv_co_{pread,pwrite,preadv,pwritev}().
bdrv_pwrite_zeroes() now also calls trace_bdrv_co_pwrite_zeroes() and
clears the BDRV_REQ_MAY_UNMAP flag when appropriate, which it didn't
previously.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Message-Id: <20220609152744.3891847-8-afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement bdrv_{pread,pwrite}() using generated_co_wrapper.
unsigned int fits in int64_t, so all callers remain correct.
bdrv_check_request32() is called further down the stack and causes -EIO
to be returned if 'bytes' is negative or greater than
BDRV_REQUEST_MAX_BYTES, which in turns never exceeds SIZE_MAX.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Message-Id: <20220609152744.3891847-7-afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
It does not mutate the buffer.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220609152744.3891847-6-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
They currently return the value of their headerlen/buflen parameter on
success. Returning 0 instead makes it clear that short reads/writes are
not possible.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220609152744.3891847-5-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
In 60592cfed2 ("hw/arm/virt: dt: add kaslr-seed property"), the
kaslr-seed property was added, but the equally as important rng-seed
property was forgotten about, which has identical semantics for a
similar purpose. This commit implements it in exactly the same way as
kaslr-seed. It then changes the name of the disabling option to reflect
that this has more to do with randomness vs determinism, rather than
something particular about kaslr.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[PMM: added deprecated.rst section for the deprecation]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This queue consists of improvements and bug fixes in TCG, powernv and
pSeries, with some fixes in other areas as well.
- tcg and target/ppc: BCDA and mffscdrn implementations, Remove CONFIG_INT128
conditional code
- fix '-cpu max' alias
- remove '-cpu default' alias
- spapr: fixes in DDW handling, H_WATCHDOG support
- powernv: cleanups in the pnv-phb3/4 models
- fix core type of MPC8555 and MPC8560 models
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCYsXrpgAKCRA82cqW3gMx
ZBe9AP4oqMTFw7r9EQPJU4QFMUeAVABl4o0xNb2wLyYov9CtKAD+LoVERSmtLTJ1
kFpgBrRTWKVylaLEdZQoTdFlJeBwzQg=
=GPG1
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20220706' of https://gitlab.com/danielhb/qemu into staging
ppc patch queue for 2022-07-06:
This queue consists of improvements and bug fixes in TCG, powernv and
pSeries, with some fixes in other areas as well.
- tcg and target/ppc: BCDA and mffscdrn implementations, Remove CONFIG_INT128
conditional code
- fix '-cpu max' alias
- remove '-cpu default' alias
- spapr: fixes in DDW handling, H_WATCHDOG support
- powernv: cleanups in the pnv-phb3/4 models
- fix core type of MPC8555 and MPC8560 models
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYKAB0WIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCYsXrpgAKCRA82cqW3gMx
# ZBe9AP4oqMTFw7r9EQPJU4QFMUeAVABl4o0xNb2wLyYov9CtKAD+LoVERSmtLTJ1
# kFpgBrRTWKVylaLEdZQoTdFlJeBwzQg=
# =GPG1
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 07 Jul 2022 01:38:06 AM +0530
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20220706' of https://gitlab.com/danielhb/qemu: (34 commits)
target/ppc: Fix MPC8555 and MPC8560 core type to e500v1
target/ppc/cpu-models: Remove the "default" CPU alias
target/ppc: Return default CPU for max CPU
target/ppc: implement cdtbcd
target/ppc: implement cbcdtd
target/ppc: implement addg6s
target/ppc: Add flag for ISA v2.06 BCDA instructions
tests/tcg/ppc64: Add mffsce test
target/ppc: Implement mffscdrn[i] instructions
target/ppc: Move mffs[.] to decodetree
target/ppc: Move mffsl to decodetree
target/ppc: Move mffsce to decodetree
target/ppc: Move mffscrn[i] to decodetree
target/ppc: Fix insn32.decode style issues
ppc/spapr: Implement H_WATCHDOG
ppc: Define SETFIELD for the ppc target
target/ppc: use int128.h methods in vsubcuq
target/ppc: use int128.h methods in vsubecuq and vsubeuqm
target/ppc: use int128.h methods in vsubuqm
target/ppc: use int128.h methods in vaddcuq
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The new PAPR 2.12 defines a watchdog facility managed via the new
H_WATCHDOG hypercall.
This adds H_WATCHDOG support which a proposed driver for pseries uses:
https://patchwork.ozlabs.org/project/linuxppc-dev/list/?series=303120
This was tested by running QEMU with a debug kernel and command line:
-append \
"pseries-wdt.timeout=60 pseries-wdt.nowayout=1 pseries-wdt.action=2"
and running "echo V > /dev/watchdog0" inside the VM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220622051008.1067464-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
It keeps repeating, move it to the header. This uses __builtin_ffsll() to
allow using the macros in #define.
This is not using the QEMU's FIELD macros as this would require changing
all such macros found in skiboot (the PPC PowerNV firmware).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220628080544.1509428-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
PAPR+/LoPAPR says:
===
The platform must restore the default DMA window for the PE on a call
to the ibm,remove-pe-dma-window RTAS call when all of the following
are true:
a. The call removes the last DMA window remaining for the PE.
b. The DMA window being removed is not the default window
===
This resets DMA as PAPR mandates.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220622052955.1069903-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
It is not advisable to execute an object_dynamic_cast() to poke into
bus->qbus.parent and follow it up with a C cast into the PnvPHB type we
think we got.
In fact this is not needed. There is nothing sophisticated being done
with the PHB object retrieved during root_port_realize() for both PHB3
and PHB4. We're retrieving a PHB reference just to access phb->chip_id
and phb->phb_id and use them to define the chassis/slot of the root
port.
phb->phb_id is already being passed to pnv_phb_attach_root_port() via
the 'index' parameter. Let's also add a 'chip_id' parameter to this
function and assign chassis and slot right there. This will spare us
from the hassle of accessing the PHB object inside realize().
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220621173436.165912-4-danielhb413@gmail.com>
This commit wires up bootinfo's RNG seed attribute so that Linux VMs can
have their RNG seeded from the earliest possible time in boot, just like
the "rng-seed" device tree property on those platforms. The link
contains the corresponding Linux patch.
Link: https://lore.kernel.org/lkml/20220626111509.330159-1-Jason@zx2c4.com/
Based-on: <20220625152318.120849-1-Jason@zx2c4.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Message-Id: <20220626111804.330745-1-Jason@zx2c4.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
* Fix edk2/opensbi jobs to not run automatically by accident
* Improve timings in the migration qtest
* Remove libvixl disassembler
* Add ukrainian translation
* Require a recent version of libpng
-----BEGIN PGP SIGNATURE-----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=Q2vV
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2022-07-05' of https://gitlab.com/thuth/qemu into staging
* Fix memory leak in test-cutils
* Fix edk2/opensbi jobs to not run automatically by accident
* Improve timings in the migration qtest
* Remove libvixl disassembler
* Add ukrainian translation
* Require a recent version of libpng
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmLECEkRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbV7lxAAmEItM6PIoW58eWPzReKVH8LE2w3UlvOZ
# JQhNgJjuN23fqjUVkcT0yCfdNCz/nKvafHnxfHQnrAXyB5V5vU8ovBgSuWK2mcmD
# NTFK+/2x5lcsyBrOe3QoeD2g1r7+Os3AYVkdnN/t2HAMLwQyaoshKaMV/UHC9O/i
# Kle1svYRNyCgyXJgxaOdbVMBSLi/L9h2R5AaG31GIi9wnf0n8HDH/ONtmeIpN09g
# BlMeZqPhGJT+tpMvviif65/Za57Y9h/r+TOgEIIs00cWmxqaBmcXXN9qog2s0n7A
# nOm3ck2lpGJCQ6+sl6/Mphyr3X6nWHsxGrLDElS0Ba5bg6T/Xqfg2pBcb81Klkjc
# QcTdFPiMxKUczgpFq326sqiaVzMgys4vwnW5iPSd5swNzrkYKADAIreki5jyM3cH
# lohBG/ruOmg5xMkX2K6pra0iOAeCz44Ku/HTREfY1CTUgEQZJY4SZrMJSnmUTnM+
# EQCkDcmOsnFDaQazneCbo18l37cXOgEhH8VoGAOqg1aRjr7TNlsJzx87PoD+9zNR
# GEh7kp18ABRGik5ZACdLQ/HhhOJa8+UWsGCwCdeBGv/TVug1Byz0OUG0PxX3X5SV
# WwubeKyZcqzoH92SQI3jZGSmuGBySy9q51T2k8FjZvaDsPiUN/MLPspNezH1qj2B
# W7qEaqIyGmo=
# =Q2vV
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 05 Jul 2022 03:15:45 PM +0530
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [undefined]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2022-07-05' of https://gitlab.com/thuth/qemu:
include/qemu/host-utils: Remove unused code in the *_overflow wrappers
meson.build: Require a recent version of libpng
po: add ukrainian translation
disas: Remove libvixl disassembler
tests: use consistent bandwidth/downtime limits in migration tests
tests: increase migration test converge downtime to 30 seconds
tests: wait for migration completion before looking for STOP event
tests: wait max 120 seconds for migration test status changes
gitlab-ci: Extend timeout for ubuntu-20.04-s390x-all to 75m
gitlab: honour QEMU_CI variable in edk2/opensbi jobs
gitlab: tweak comments in edk2/opensbi jobs
gitlab: normalize indentation in edk2/opensbi rules
tests/fp: Do not build softfloat3 tests if TCG is disabled
tests: fix test-cutils leaks
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In general loongarch ipi device, 32bit registers is emulated, however for
anysend/mailsend device only 64bit register access is supported. So separate
the ipi memory region into two regions, including 32 bits and 64 bits.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220705064901.2353349-2-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
According to commit cec07c0b61 the code in the #else paths was required
for GCC < 5.0 and Clang < 3.8. We don't support such old compilers
at all anymore, so we can remove these lines now. We keep the wrapper
function, though, since they are easier to read and help to make sure that
the parameters have the right types.
Message-Id: <20220701025132.303469-1-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The disassembly via capstone should be superiour to our old vixl
sources nowadays, so let's finally cut this old disassembler out
of the QEMU source tree.
Message-Id: <20220603164249.112459-1-thuth@redhat.com>
Tested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Loongarch pch msi intc connects to extioi controller, the range of irq
number is 64-255. Add a property for irqbase, so that we can compute
the irq offset from the view of pch_msi controller with the method:
msi vector (from view of upper extioi intc) - irqbase
Signed-off-by: Mao Bibo <maobibo@loongson.cn>
Message-Id: <20220701030740.2469162-1-maobibo@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The update makes it easier to find and specify devices.
They can only be found by device type name without the id field,
for example, devices of the same type have the same label.
The update also adds a head field,
which is useful for devices that support multiple heads,
such as virtio-gpu.
Signed-off-by: Jianxian Wen <jianxian.wen@verisilicon.com>
Signed-off-by: Lu Gao <lu.gao@verisilicon.com>
Message-Id: <4C23C17B8E87E74E906A25A3254A03F4018FC045B0@SHASXM06.verisilicon.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This introduces a really basic PECI controller that responses to
commands by always setting the response code to success and then raising
an interrupt to indicate the command is done. This helps avoid getting
hit with constant errors if the driver continuously attempts to send a
command and keeps timing out.
The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC.
They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support
PECI 4.0, which includes more read/write buffer registers from 0x80 to
0xFC to support 64-byte mode.
This patch doesn't attempt to handle that, or to create a different
version of the controller for the different generations, since it's only
implementing functionality that is common to all generations.
The basic sequence of events is that the firmware will read and write to
various registers and then trigger a command by setting the FIRE bit in
the command register (similar to the I2C controller).
Then the firmware waits for an interrupt from the PECI controller,
expecting the interrupt status register to be filled in with info on
what happened. If the command was transmitted and received successfully,
then response codes from the host CPU will be found in the data buffer
registers.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-12-me@pjd.dev>
[ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds support for DMA RX in slave mode while using the new
register set in the AST2600 and AST1030. This patch also pretty much
assumes packet mode is enabled, I'm not sure if this will work in DMA
step mode.
This is particularly useful for testing IPMB exchanges between Zephyr
and external devices, which requires multi-master I2C support and DMA in
the new register mode, because the Zephyr drivers from Aspeed use DMA in
the new mode by default. The Zephyr drivers are also using packet mode.
The typical sequence of events for receiving data in DMA slave + packet
mode is that the Zephyr firmware will configure the slave address
register with an address to receive on and configure the bus's function
control register to enable master mode and slave mode simultaneously at
startup, before any transfers are initiated.
RX DMA is enabled in the slave mode command register, and the slave RX
DMA buffer address and slave RX DMA buffer length are set. TX DMA is not
covered in this patch.
When the Aspeed I2C controller receives data from some other I2C master,
it will reset the I2CS_DMA_LEN RX_LEN value to zero, then buffer
incoming data in the RX DMA buffer while incrementing the I2CC_DMA_ADDR
address counter and decrementing the I2CC_DMA_LEN counter. It will also
update the I2CS_DMA_LEN RX_LEN value along the way.
Once all the data has been received, the bus controller will raise an
interrupt indicating a packet command was completed, the slave address
matched, a normal stop condition was seen, and the transfer was an RX
operation.
If the master sent a NACK instead of a normal stop condition, or the
transfer timed out, then a slightly different set of interrupt status
values would be set. Those conditions are not handled in this commit.
The Zephyr firmware then collects data from the RX DMA buffer and clears
the status register by writing the PKT_MODE_EN bit to the status
register. In packet mode, clearing the packet mode interrupt enable bit
also clears most of the other interrupt bits automatically (except for a
few bits above it).
Note: if the master transmit or receive functions were in use
simultaneously with the slave mode receive functionality, then the
master mode functions may have raised the interrupt line for the bus
before the DMA slave transfer is complete. It's important to have the
slave's interrupt status register clear throughout the receive
operation, and if the slave attempts to raise the interrupt before the
master interrupt status is cleared, then it needs to re-raise the
interrupt once the master interrupt status is cleared. (And vice-versa).
That's why in this commit, when the master interrupt status is cleared
and the interrupt line is lowered, we call the slave interrupt _raise_
function, to see if the interrupt was pending. (And again, vice-versa).
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-8-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add slave mode functionality for the Aspeed I2C controller in old
register mode. This is implemented by realizing an I2C slave device
owned by the I2C controller and attached to its own bus.
The I2C slave device only implements asynchronous sends on the bus, so
slaves not supporting that will not be able to communicate with it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: checkpatch fixes ]
Message-Id: <20220601210831.67259-6-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-7-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allow slaves to master the bus by registering a bottom halve. If the bus
is busy, the bottom half is queued up. When a slave has succesfully
mastered the bus, the bottom half is scheduled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg : - fixed typos in commit log ]
Message-Id: <20220601210831.67259-4-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-5-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
sysbus_mmio_map maps devices into "get_system_memory()".
With the new SoC memory attribute, we want to make sure that each device is
mapped into the SoC memory.
In single SoC machines, the SoC memory is the same as "get_system_memory()",
but in multi SoC machines it will be different.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Multi-SoC machines can use this property to specify a memory container
for each SoC. Single SoC machines will just specify get_system_memory().
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the Aspeed machines allocate a ram container region in
which the machine ram region is mapped. See commit ad1a978218
("aspeed: add a RAM memory region container"). An extra region is
mapped after ram in the ram container to catch invalid access done by
FW. That's how FW determines the size of ram. See commit ebe31c0a8e
("aspeed: add a max_ram_size property to the memory controller").
Let's move all the logic under the SoC where it should be. It will
also ease the work on multi SoC support.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220623202123.3972977-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
v2: - add arguments to QEMUMachine constructor in test, to make it work
on arm in gitlab pipeline
- use bdrv_inc_in_flight() / bdrv_dec_in_flight() instead of direct
manipulation with bs->in_flight
- add new options for copy-before-write filter
- new trace points for NBD
- prefer unsigned type for some 'in_flight' fields
-----BEGIN PGP SIGNATURE-----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=ndKk
-----END PGP SIGNATURE-----
Merge tag 'pull-block-2022-06-14-v2' of https://gitlab.com/vsementsov/qemu into staging
Block jobs & NBD patches
v2: - add arguments to QEMUMachine constructor in test, to make it work
on arm in gitlab pipeline
- use bdrv_inc_in_flight() / bdrv_dec_in_flight() instead of direct
manipulation with bs->in_flight
- add new options for copy-before-write filter
- new trace points for NBD
- prefer unsigned type for some 'in_flight' fields
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCgAdFiEEi5wmzbL9FHyIDoahVh8kwfGfefsFAmK8BqkACgkQVh8kwfGf
# efuiMw/+P9FFLfGFSjVP+LYeT0Ah6kN1ypCMQzIk3Qq/J6qgMZhtRqpQoZOfIFQL
# U9fGmEtQZ7gvEMD/nJToL6uOYlnQfPxDcA6GrRwWWE3rcFiPK4J0q2LlnPLn4QaU
# W/qag5l/QnZfLlj/iV6neWOEvqdnvY1L8IS+T8xV6N0iBYlwgMC/6FGshQwehzcV
# T5F1qPGB0vjFDjf92LFPEsvsFFHjHIVPwOyJMvF64QtSk57utikq/la9PI/yA9AH
# Ll4mNQuZKx6rSI5wE6b21jc8iOUvaoHdPSEDQZfNILSdgGdiKvFwE51y+baGnIAD
# TpjxfG59q0jyGxMjQVxMRSFaxAC4+Mqi82diSPv4xbiUdsE4byJH0oENn4z7+wAv
# EvjuU9yx4FfHHltoUNwfn2pv00o/ELdZIoBNmW36rPxSGZMvfVfRtuBL7XWNUFbW
# Fr4BwsjC4KfIxb16QTBGhXVv6grxdlwoU9N23npdi0YpW1ftZzXGDa85+gINQ807
# eK/gP/OtYPwIql0bgmLiuaRNzC9psmQOO6vQbdvd/e4BEVWkxiez37+e+zFMStmL
# OAL8rS6jckUoxVZjCYFEWg97XOobLUIhQxt9Fwh2omMDGKTwv861ghUAivxSWs93
# IRNxfwqNPxnpDDXjnK1ayZgU08IL98AUYVKcPN1y8JvEhB4Hr1k=
# =ndKk
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 29 Jun 2022 01:30:41 PM +0530
# gpg: using RSA key 8B9C26CDB2FD147C880E86A1561F24C1F19F79FB
# gpg: Good signature from "Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>" [unknown]
# gpg: aka "Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8B9C 26CD B2FD 147C 880E 86A1 561F 24C1 F19F 79FB
* tag 'pull-block-2022-06-14-v2' of https://gitlab.com/vsementsov/qemu:
block: use 'unsigned' for in_flight field on driver state
nbd: trace long NBD operations
iotests: copy-before-write: add cases for cbw-timeout option
block/copy-before-write: implement cbw-timeout option
block/block-copy: block_copy(): add timeout_ns parameter
util: add qemu-co-timeout
iotests: add copy-before-write: on-cbw-error tests
block/copy-before-write: add on-cbw-error open parameter
block/copy-before-write: refactor option parsing
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add possibility to limit block_copy() call in time. To be used in the
next commit.
As timed-out block_copy() call will continue in background anyway (we
can't immediately cancel IO operation), it's important also give user a
possibility to pass a callback, to do some additional actions on
block-copy call finish.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Add new API, to make a time limited call of the coroutine.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
xen_piix_pci_write_config_client() is implemented in the xen sub tree and
uses PIIX constants internally, thus creating a direct dependency on
PIIX. Now that xen_set_pci_link_route() is stubbable, the logic of
xen_piix_pci_write_config_client() can be moved to PIIX which resolves
the dependency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-3-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The only user of xen_set_pci_link_route() is
xen_piix_pci_write_config_client() which implements PIIX-specific logic in
the xen namespace. This makes xen-hvm depend on PIIX which could be
avoided if xen_piix_pci_write_config_client() was implemented in PIIX. In
order to do this, xen_set_pci_link_route() needs to be stubbable which
this patch addresses.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-2-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
pi440fx_state is an out-parameter which is never read by the caller.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220612192800.40813-1-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It always returns IOVA_OK so nobody uses it.
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20220427154931.3166388-1-eperezma@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will be used for implementing the xtensa select_one
system call. Choose "poll" over "select" so that we can
reuse Glib's g_poll constants and to avoid struct timeval.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This function has been replaced by *_write.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This function has been replaced by *_write.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For arm-compat, initialize console_{in,out}_gf;
otherwise, initialize stdio file descriptors.
This will go some way to cleaning up arm-compat, and
will allow other semihosting to use normal stdio.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add a GuestFDType for connecting to the semihosting console.
Hook up to read, write, isatty, and fstat syscalls.
Note that the arm-specific syscall flen cannot be applied
to the console, because the console is not a descriptor
exposed to the guest.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Will replace qemu_semihosting_console_{outs,outc},
but we need more plumbing first.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Rename qemu_semihosting_connect_chardevs to
qemu_semihosting_chardev_init; pass the result
directly to qemu_semihosting_console_init.
Store the chardev in SemihostingConsole instead
of SemihostingConfig, which lets us drop
semihosting_get_chardev.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allow more than one character to be read at one time.
Will be used by m68k and nios2 semihosting for stdio.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We don't need CPUArchState, and we do want the CPUState of the
thread performing the operation -- use this instead of current_cpu.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The implementation of qemu_semihosting_console_inc does not
defer to gdbstub, but only reads from the fifo in console.c.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Change 'ret' to uint64_t. This resolves a FIXME in the
m68k and nios2 semihosting that we've lost data.
Change 'err' to int. There is nothing target-specific
about the width of the errno value.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This syscall will be used by m68k and nios2 semihosting.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
These syscalls will be used by m68k and nios2 semihosting.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out the non-ARM specific portions of SYS_SYSTEM to a
reusable function.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out the non-ARM specific portions of SYS_RENAME to a
reusable function.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out the non-ARM specific portions of SYS_REMOVE to a
reusable function.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The ARM-specific SYS_FLEN isn't really something that can be
reused by other semihosting apis, but there are parts that can
reused for the implementation of semihost_sys_fstat.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out the non-ARM specific portions of SYS_ISTTY to a
reusable function. This handles all GuestFD.
Add a common_semi_istty_cb helper to translate the Posix
error return, 0+ENOTTY, to the Arm semihosting not-a-file
success result.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out the non-ARM specific portions of SYS_SEEK to a
reusable function. This handles all GuestFD. Isolate the
curious ARM-specific return value processing to a new
callback, common_semi_seek_cb.
Expand the internal type of the offset to int64_t, and
provide the whence argument, which will be required by
m68k and nios2 semihosting.
Note that gdb_do_syscall %x reads target_ulong, not int.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out the non-ARM specific portions of SYS_WRITE to a
reusable function. This handles all GuestFD. This removes
the last use of common_semi_syscall_len.
Note that gdb_do_syscall %x reads target_ulong, not int.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out the non-ARM specific portions of SYS_READ to a
reusable function. This handles all GuestFD. Isolate the
curious ARM-specific return value processing to a new
callback, common_semi_rw_cb.
Note that gdb_do_syscall %x reads target_ulong, not int.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out the non-ARM specific portions of SYS_CLOSE to a
reusable function. This handles all GuestFD.
Note that gdb_do_syscall %x reads target_ulong, not int.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Split out the non-ARM specific portions of SYS_OPEN to a
reusable function. This handles gdb and host file i/o.
Add helpers to validate the length of the filename string.
Prepare for usage by other semihosting by allowing the
filename length parameter to be 0, and calling strlen.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Define constants for the errno values defined by the
gdb remote fileio protocol.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We have two copies of these structures, and require them
in semihosting/ going forward.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There were 3 copies of these flags. Place them in the
file with gdb_do_syscall, with which they belong.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This header is not private to the top-level semihosting directory,
so place it in the public include directory.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In arm-compat-semi.c, we have more advanced treatment of
guest file descriptors than we do in other implementations.
Split out GuestFD and related functions to a new file so
that they can be shared.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Mirror the interface of the user-only function of the same name.
Use probe_access_flags for the common case of ram, and
cpu_memory_rw_debug for the uncommon case of mmio.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
---
v3: Use probe_access_flags (pmm)
Rather that static (and not even inline) functions within a
header, move the functions to semihosting/uaccess.c.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We were reporting unconditional success for these functions;
pass on any failure from cpu_memory_rw_debug.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We have a subdirectory for semihosting; move this file out of exec.
Rename to emphasize the contents are a replacement for the functions
in linux-user/bsd-user uaccess.c.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220524154056.2896913-5-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220524154056.2896913-4-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Vhost has error notifications, let's log them like other errors.
For each virt-queue setup eventfd for vring error notifications.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
[vsementsov: rename patch, change commit message and dump error like
other errors in the file]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20220623161325.18813-3-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Roman Kagan <rvkagan@yandex-team.ru>
Kernel and user vhost may report virtqueue errors via eventfd.
This is only reliable way to get notification about protocol error.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Message-Id: <20220623161325.18813-2-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Roman Kagan <rvkagan@yandex-team.ru>
We need to fetch the name of the current accelerator in flexible error
messages more going forward. Let's create a helper that gives it to us
without casting in the target code.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220620192242.70573-1-agraf@csgraf.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that all the PS2 devices have been converted to use GPIOs the update_irq()
callback function and the update_arg parameter can be removed.
This allows these arguments to be completely removed from ps2_kbd_init() and
ps2_mouse_init(), along with the transitional logic that was added to
ps2_raise_irq() and ps2_lower_irq().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-55-mark.cave-ayland@ilande.co.uk>
This describes the I8042 device interface implemented within QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220624134109.881989-54-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This describes the I8042_MMIO device interface implemented within QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220624134109.881989-51-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This describes the LASI PS2 device interface implemented within QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220624134109.881989-49-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This is in preparation for handling vmstate_register() within the device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-45-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Now that the register memory regions are exposed as SysBus memory regions, move
the mapping of the LASIPS2 registers from lasips2_initfn() to the HPPA machine
(which is its only user).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-43-mark.cave-ayland@ilande.co.uk>
When QOMifying a device it is typical to use _init() as the suffix for an
instance_init function, however this name is already in use by the legacy LASIPS2
wrapper function. Eventually the wrapper function will be removed, but for now
rename it to lasips2_initfn() to avoid a naming collision.
At the same time update lasips2_initfn() return the LASIPS2 device so that it
can later be accessed using qdev APIs by the HPPA machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-41-mark.cave-ayland@ilande.co.uk>
This allows the QOM types in lasips2.c to be used elsewhere by simply including
lasips2.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-40-mark.cave-ayland@ilande.co.uk>
This allows both IRQs to be declared as a single qdev gpio array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-36-mark.cave-ayland@ilande.co.uk>
Define the gpio for the PS2 output IRQ in ps2_init() and add logic to optionally
use it in ps2_raise_irq() and ps2_lower_irq() if the gpio is connected. If the
gpio is not connected then call the legacy update_irq() function as before.
This allows the incremental conversion of devices from the legacy update_irq()
function to use gpios instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-35-mark.cave-ayland@ilande.co.uk>
This function is no longer used outside of ps2.c and so can be declared static.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-32-mark.cave-ayland@ilande.co.uk>
Now that the register memory region is exposed as a SysBus memory region, move
the mapping of the I8042_MMIO registers from i8042_mm_init() to the MIPS magnum
machine (which is its only user).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-29-mark.cave-ayland@ilande.co.uk>
This exposes the I8042_MMIO device to the caller to allow the register memory
region to be mapped outside of i8042_mm_init().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-28-mark.cave-ayland@ilande.co.uk>
Move the initialisation of the register memory region to the I8042_MMIO device
realize function and expose it using sysbus_init_mmio().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-26-mark.cave-ayland@ilande.co.uk>
This will soon be used to set the size of the register memory region using a
qdev property.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-25-mark.cave-ayland@ilande.co.uk>
Currently i8042_mm_init() creates a new KBDState directly which is used by the MIPS
magnum machine. Introduce a new I8042_MMIO QOM type that will soon be used to
allow the MIPS magnum machine to be wired up using standard qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-22-mark.cave-ayland@ilande.co.uk>
This allows the QOM types in pckbd.c to be used elsewhere by simply including
i8042.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-21-mark.cave-ayland@ilande.co.uk>
This allows the QOM types in pckbd.c to be used elsewhere by simply including
i8042.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-20-mark.cave-ayland@ilande.co.uk>
The functionality of ps2_common_reset() can be moved into a new ps2_reset() function
for the PS2_DEVICE QOM type. Update PS2DeviceClass to hold a reference to the parent
reset function and update the PS2_KBD_DEVICE and PS2_MOUSE_DEVICE types to use
device_class_set_parent_reset() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-9-mark.cave-ayland@ilande.co.uk>
This is in preparation for allowing the new PS2_KBD_DEVICE and PS2_MOUSE_DEVICE
QOM types to reference the parent PS2_DEVICE device reset() function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-8-mark.cave-ayland@ilande.co.uk>
With the latest changes it is now possible to improve some of the function
prototypes in ps2.c and ps.h to use the appropriate PS2KbdState or
PS2MouseState type instead of being a void opaque.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-7-mark.cave-ayland@ilande.co.uk>
Move the QOM type definitions into the ps2.h header file to allow the new QOM
types to be used by other devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-6-mark.cave-ayland@ilande.co.uk>
It seems that aio_wait_kick always required a memory barrier
or atomic operation in the caller, but nobody actually
took care of doing it.
Let's put the barrier in the function instead, and pair it
with another one in AIO_WAIT_WHILE. Read aio_wait_kick()
comment for further explanation.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220524173054.12651-1-eesposit@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We have too much logic to simply check that bitmaps are of the same
size. Let's just define that hbitmap_merge() and
bdrv_dirty_bitmap_merge_internal() require their argument bitmaps be of
same size, this simplifies things.
Let's look through the callers:
For backup_init_bcs_bitmap() we already assert that merge can't fail.
In bdrv_reclaim_dirty_bitmap_locked() we gracefully handle the error
that can't happen: successor always has same size as its parent, drop
this logic.
In bdrv_merge_dirty_bitmap() we already has assertion and separate
check. Make the check explicit and improve error message.
Signed-off-by: Vladimir Sementsov-Ogievskiy <v.sementsov-og@mail.ru>
Reviewed-by: Nikita Lapshin <nikita.lapshin@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20220517111206.23585-4-v.sementsov-og@mail.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 1b7fd72955 ("block: rename buffer_alignment to
guest_block_size") noted:
At this point, the field is set by the device emulation, but completely
ignored by the block layer.
The last time the value of buffer_alignment/guest_block_size was
actually used was before commit 339064d506 ("block: Don't use guest
sector size for qemu_blockalign()").
This value has not been used since 2013. Get rid of it.
Cc: Xie Yongji <xieyongji@bytedance.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220518130945.2657905-1-stefanha@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Faria <afaria@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_co_drain() has not been used since commit 9a0cec664e ("mirror:
use bdrv_drained_begin/bdrv_drained_end") in 2016. Remove it so there
are fewer drain scenarios to worry about.
Use bdrv_drained_begin()/bdrv_drained_end() instead. They are "mixed"
functions that can be called from coroutine context. Unlike
bdrv_co_drain(), these functions provide control of the length of the
drained section, which is usually the right thing.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220521122714.3837731-1-stefanha@redhat.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Alberto Faria <afaria@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With the new command one can:
- assign flexible resources (queues, interrupts) to primary and
secondary controllers,
- toggle the online/offline state of given controller.
Signed-off-by: Łukasz Gieryk <lukasz.gieryk@linux.intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
With four new properties:
- sriov_v{i,q}_flexible,
- sriov_max_v{i,q}_per_vf,
one can configure the number of available flexible resources, as well as
the limits. The primary and secondary controller capability structures
are initialized accordingly.
Since the number of available queues (interrupts) now varies between
VF/PF, BAR size calculation is also adjusted.
Signed-off-by: Łukasz Gieryk <lukasz.gieryk@linux.intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Introduce handling for Secondary Controller List (Identify command with
CNS value of 15h).
Secondary controller ids are unique in the subsystem, hence they are
reserved by it upon initialization of the primary controller to the
number of sriov_max_vfs.
ID reservation requires the addition of an intermediate controller slot
state, so the reserved controller has the address 0xFFFF.
A secondary controller is in the reserved state when it has no virtual
function assigned, but its primary controller is realized.
Secondary controller reservations are released to NULL when its primary
controller is unregistered.
Signed-off-by: Lukasz Maniak <lukasz.maniak@linux.intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Implementation of Primary Controller Capabilities data
structure (Identify command with CNS value of 14h).
Currently, the command returns only ID of a primary controller.
Handling of remaining fields are added in subsequent patches
implementing virtualization enhancements.
Signed-off-by: Lukasz Maniak <lukasz.maniak@linux.intel.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch implements initial support for Single Root I/O Virtualization
on an NVMe device.
Essentially, it allows to define the maximum number of virtual functions
supported by the NVMe controller via sriov_max_vfs parameter.
Passing a non-zero value to sriov_max_vfs triggers reporting of SR-IOV
capability by a physical controller and ARI capability by both the
physical and virtual function devices.
NVMe controllers created via virtual functions mirror functionally
the physical controller, which may not entirely be the case, thus
consideration would be needed on the way to limit the capabilities of
the VF.
NVMe subsystem is required for the use of SR-IOV.
Signed-off-by: Lukasz Maniak <lukasz.maniak@linux.intel.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This is for code which needs a portable equivalent to a QIOChannelFile
connected to /dev/null.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add support for writing and reading the device address register in old
register mode.
On the AST2400 (only 1 slave address)
* no upper bits
On the AST2500 (2 possible slave addresses),
* bit[31] : Slave Address match indicator
* bit[30] : Slave Address Receiving pending
On the AST2600 (3 possible slave addresses),
* bit[31-30] : Slave Address match indicator
* bit[29] : Slave Address Receiving pending
The model could be more precise to take into account all fields but
since the Linux driver is masking the register value being set, it
should be fine. See commit 3fb2e2aeafb2 ("i2c: aspeed: disable
additional device addresses on ast2[56]xx") from Zeiv. This can be
addressed later.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: add details to commit log ]
Message-Id: <20220601210831.67259-3-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Moves register definitions and short commonly used inlined functiosn to
the header file to help tidy up the implementation file.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I34dff7485b6bbe3c9482715ccd94dbd65dc5f324
Message-Id: <20220331043248.2237838-8-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On AST2600, I2C has a secondary mode, called "new mode", which changes
the layout of registers, adds some minor behavior changes, and
introduces a new way to transfer data called "packet mode".
Most of the bit positions of the fields are the same between old and new
mode, so we use SHARED_FIELD_XX macros to reuse most of the code between
the different modes.
For packet mode, most of the command behavior is the same compared to
other modes, but there are some minor changes to how interrupts are
handled compared to other modes.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I072f8301964f623afc74af1fe50c12e5caef199e
Message-Id: <20220331043248.2237838-6-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a register array will allow us to represent old-mode and new-mode
I2C registers by using the same underlying register array, instead of
adding an entire new set of variables to represent new mode.
As part of this, we also do additional cleanup to use ARRAY_FIELD_
macros instead of FIELD_ macros on registers.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Ib94996b17c361b8490c042b43c99d8abc69332e3
[ clg: use of memset in aspeed_i2c_bus_reset() ]
Message-Id: <20220331043248.2237838-5-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Occasionally a peripheral will have different operating modes, where the
MMIO layout changes, but some of the register fields have the same offsets
and behaviors.
To help support this, we add SHARED_FIELD_XX macros that create SHIFT,
LENGTH, and MASK macros for the fields that are shared across registers,
and accessors for these fields.
An example use may look as follows:
There is a peripheral with registers REG_MODE1 and REG_MODE2 at
different addreses, and both have a field FIELD1 initialized by
SHARED_FIELD().
Depending on what mode the peripheral is operating in, the user could
extract FIELD1 via
SHARED_ARRAY_FIELD_EX32(s->regs, R_REG_MODE1, FIELD1)
or
SHARED_ARRAY_FIELD_EX32(s->regs, R_REG_MODE2, FIELD1)
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Id3dc53e7d2f8741c95697cbae69a81bb699fa3cb
Message-Id: <20220331043248.2237838-2-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Based on already existing QEMU implementation created a signed
256 bit by 128 bit division needed to implement the vector divide
extended signed quadword instruction from PowerISA 3.1
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220525134954.85056-6-lucas.araujo@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Based on already existing QEMU implementation, created an unsigned 256
bit by 128 bit division needed to implement the vector divide extended
unsigned instruction from PowerISA3.1
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220525134954.85056-5-lucas.araujo@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
There are two parts in this patch:
1, support akcipher service by cryptodev-builtin driver
2, virtio-crypto driver supports akcipher service
In principle, we should separate this into two patches, to avoid
compiling error, merge them into one.
Then virtio-crypto gets request from guest side, and forwards the
request to builtin driver to handle it.
Test with a guest linux:
1, The self-test framework of crypto layer works fine in guest kernel
2, Test with Linux guest(with asym support), the following script
test(note that pkey_XXX is supported only in a newer version of keyutils):
- both public key & private key
- create/close session
- encrypt/decrypt/sign/verify basic driver operation
- also test with kernel crypto layer(pkey add/query)
All the cases work fine.
Run script in guest:
rm -rf *.der *.pem *.pfx
modprobe pkcs8_key_parser # if CONFIG_PKCS8_PRIVATE_KEY_PARSER=m
rm -rf /tmp/data
dd if=/dev/random of=/tmp/data count=1 bs=20
openssl req -nodes -x509 -newkey rsa:2048 -keyout key.pem -out cert.pem -subj "/C=CN/ST=BJ/L=HD/O=qemu/OU=dev/CN=qemu/emailAddress=qemu@qemu.org"
openssl pkcs8 -in key.pem -topk8 -nocrypt -outform DER -out key.der
openssl x509 -in cert.pem -inform PEM -outform DER -out cert.der
PRIV_KEY_ID=`cat key.der | keyctl padd asymmetric test_priv_key @s`
echo "priv key id = "$PRIV_KEY_ID
PUB_KEY_ID=`cat cert.der | keyctl padd asymmetric test_pub_key @s`
echo "pub key id = "$PUB_KEY_ID
keyctl pkey_query $PRIV_KEY_ID 0
keyctl pkey_query $PUB_KEY_ID 0
echo "Enc with priv key..."
keyctl pkey_encrypt $PRIV_KEY_ID 0 /tmp/data enc=pkcs1 >/tmp/enc.priv
echo "Dec with pub key..."
keyctl pkey_decrypt $PRIV_KEY_ID 0 /tmp/enc.priv enc=pkcs1 >/tmp/dec
cmp /tmp/data /tmp/dec
echo "Sign with priv key..."
keyctl pkey_sign $PRIV_KEY_ID 0 /tmp/data enc=pkcs1 hash=sha1 > /tmp/sig
echo "Verify with pub key..."
keyctl pkey_verify $PRIV_KEY_ID 0 /tmp/data /tmp/sig enc=pkcs1 hash=sha1
echo "Enc with pub key..."
keyctl pkey_encrypt $PUB_KEY_ID 0 /tmp/data enc=pkcs1 >/tmp/enc.pub
echo "Dec with priv key..."
keyctl pkey_decrypt $PRIV_KEY_ID 0 /tmp/enc.pub enc=pkcs1 >/tmp/dec
cmp /tmp/data /tmp/dec
echo "Verify with pub key..."
keyctl pkey_verify $PUB_KEY_ID 0 /tmp/data /tmp/sig enc=pkcs1 hash=sha1
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: lei he <helei.sig11@bytedance.com
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20220611064243.24535-2-pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When switching address space with mutex lock hold, mapping will be
replayed for assigned device. This will trigger relock deadlock.
Also release the mutex resource in unrealize routine.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220613061010.2674054-3-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently assigned devices can not work in virtio-iommu bypass mode.
Guest driver fails to probe the device due to DMA failure. And the
reason is because of lacking GPA -> HPA mappings when VM is created.
Add a root container memory region to hold both bypass memory region
and iommu memory region, so the switch between them is supported
just like the implementation in virtual VT-d.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220613061010.2674054-2-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
An initial simple upstream port emulation to allow the creation
of CXL switches. The Device ID has been allocated for this use.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220616145126.8002-2-Jonathan.Cameron@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* virtio reset cleanups
* build system cleanups
* fix Cirrus CI
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmKpooQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNlFwf+OugLGRZl3KVc7akQwUJe9gg2T31h
VkC+7Tei8FAwe8vDppVd+CYEIi0M3acxD2amRrv2etCCGSuySN1PbkfRcSfPBX01
pRWpasdhfqnZR8Iidi7YW1Ou5CcGqKH49nunBhW10+osb/mu5sVscMuOJgTDj/lK
CpsmDyk6572yGmczjNLlmhYcTU36clHpAZgazZHwk1PU+B3fCKlYYyvUpT3ItJvd
cK92aIUWrfofl3yTy0k4IwvZwNjTBirlstOIomZ333xzSA+mm5TR+mTvGRTZ69+a
v+snpMp4ILDMoB5kxQ42kK5WpdiN//LnriA9CBFDtOidsDDn8kx7gJe2RA==
=Dxwa
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* statistics subsystem
* virtio reset cleanups
* build system cleanups
* fix Cirrus CI
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmKpooQUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroNlFwf+OugLGRZl3KVc7akQwUJe9gg2T31h
# VkC+7Tei8FAwe8vDppVd+CYEIi0M3acxD2amRrv2etCCGSuySN1PbkfRcSfPBX01
# pRWpasdhfqnZR8Iidi7YW1Ou5CcGqKH49nunBhW10+osb/mu5sVscMuOJgTDj/lK
# CpsmDyk6572yGmczjNLlmhYcTU36clHpAZgazZHwk1PU+B3fCKlYYyvUpT3ItJvd
# cK92aIUWrfofl3yTy0k4IwvZwNjTBirlstOIomZ333xzSA+mm5TR+mTvGRTZ69+a
# v+snpMp4ILDMoB5kxQ42kK5WpdiN//LnriA9CBFDtOidsDDn8kx7gJe2RA==
# =Dxwa
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 15 Jun 2022 02:12:36 AM PDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [undefined]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (21 commits)
build: include pc-bios/ part in the ROMS variable
meson: put cross compiler info in a separate section
q35：Enable TSEG only when G_SMRAME and TSEG_EN both enabled
build: fix check for -fsanitize-coverage-allowlist
tests/vm: allow running tests in an unconfigured source tree
configure: cleanup -fno-pie detection
configure: update list of preserved environment variables
virtio-mmio: cleanup reset
virtio: stop ioeventfd on reset
virtio-mmio: stop ioeventfd on legacy reset
s390x: simplify virtio_ccw_reset_virtio
block: add more commands to preconfig mode
hmp: add filtering of statistics by name
qmp: add filtering of statistics by name
hmp: add filtering of statistics by provider
qmp: add filtering of statistics by provider
hmp: add basic "info stats" implementation
cutils: add functions for IEC and SI prefixes
qmp: add filtering of statistics by target vCPU
kvm: Support for querying fd-based stats
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Forward remote device's interrupts to the guest
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Message-id: 9523479eaafe050677f4de2af5dd0df18c27cfd9.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Determine the BARs used by the PCI device and register handlers to
manage the access to the same.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 3373e10b5be5f42846f0632d4382466e1698c505.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Assign separate address space for each device in the remote processes.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: afe0b0a97582cdad42b5b25636a29c523265a10a.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Define vfio-user object which is remote process server for QEMU. Setup
object initialization functions and properties necessary to instantiate
the object
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: e45a17001e9b38f451543a664ababdf860e5f2f2.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add vfio-user to x-remote machine. It is a boolean, which indicates if
the machine supports vfio-user protocol. The machine configures the bus
differently vfio-user and multiprocess protocols, so this property
informs it on how to configure the bus.
This property should be short lived. Once vfio-user fully replaces
multiprocess, this property could be removed.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 5d51a152a419cbda35d070b8e49b772b60a7230a.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add blocker to prevent hot-unplug of devices
TYPE_VFIO_USER_SERVER, which is introduced shortly, attaches itself to a
PCIDevice on which it depends. If the attached PCIDevice gets removed
while the server in use, it could cause it crash. To prevent this,
TYPE_VFIO_USER_SERVER adds an unplug blocker for the PCIDevice.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: c41ef80b7cc063314d629737bed2159e5713f2e0.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Allow retrieving only a subset of statistics. This can be useful
for example in order to plot a subset of the statistics many times
a second: KVM publishes ~40 statistics for each vCPU on x86; retrieving
and serializing all of them would be useless.
Another use will be in HMP in the following patch; implementing the
filter in the backend is easy enough that it was deemed okay to make
this a public interface.
Example:
{ "execute": "query-stats",
"arguments": {
"target": "vcpu",
"vcpus": [ "/machine/unattached/device[2]",
"/machine/unattached/device[4]" ],
"providers": [
{ "provider": "kvm",
"names": [ "l1d_flush", "exits" ] } } }
{ "return": {
"vcpus": [
{ "path": "/machine/unattached/device[2]"
"providers": [
{ "provider": "kvm",
"stats": [ { "name": "l1d_flush", "value": 41213 },
{ "name": "exits", "value": 74291 } ] } ] },
{ "path": "/machine/unattached/device[4]"
"providers": [
{ "provider": "kvm",
"stats": [ { "name": "l1d_flush", "value": 16132 },
{ "name": "exits", "value": 57922 } ] } ] } ] } }
Extracted from a patch by Mark Kanda.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow retrieving the statistics from a specific provider only.
This can be used in the future by HMP commands such as "info
sync-profile" or "info profile". The next patch also adds
filter-by-provider capabilities to the HMP equivalent of
query-stats, "info stats".
Example:
{ "execute": "query-stats",
"arguments": {
"target": "vm",
"providers": [
{ "provider": "kvm" } ] } }
The QAPI is a bit more verbose than just a list of StatsProvider,
so that it can be subsequently extended with filtering of statistics
by name.
If a provider is specified more than once in the filter, each request
will be included separately in the output.
Extracted from a patch by Mark Kanda.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add an HMP command to retrieve statistics collected at run-time.
The command will retrieve and print either all VM-level statistics,
or all vCPU-level statistics for the currently selected CPU.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extract the knowledge of IEC and SI prefixes out of size_to_str and
freq_to_str, so that it can be reused when printing statistics.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a simple filtering of statistics, that allows to retrieve
statistics for a subset of the guest vCPUs. This will be used for
example by the HMP monitor, in order to retrieve the statistics
for the currently selected CPU.
Example:
{ "execute": "query-stats",
"arguments": {
"target": "vcpu",
"vcpus": [ "/machine/unattached/device[2]",
"/machine/unattached/device[4]" ] } }
Extracted from a patch by Mark Kanda.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
